]>
git.gag.com Git - fw/altos/log
Keith Packard [Sun, 26 Feb 2023 06:40:29 +0000 (22:40 -0800)]
ao-tools: Add flash utility for stm32f1x chips
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 30 Jan 2024 20:33:22 +0000 (12:33 -0800)]
altos/lpc: Adjust ADC clock from 450kHz to 4.5MHz
A missing zero. Also, let products change this value if desired to
improve high-impedence performance.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 1 Feb 2024 01:47:08 +0000 (17:47 -0800)]
Fix configure tests for multi-arch libaltos
libaltos builds now require a long list of compilers. Check for all of them
before enabling it when building in auto mode.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Mon, 22 Jan 2024 23:15:44 +0000 (16:15 -0700)]
kernel: conditionalize config "report in feet" on presence of baro sensor
Keith Packard [Sun, 7 Jan 2024 06:09:41 +0000 (22:09 -0800)]
altos/easytimer-v2: Initialize logging too
Now that the logging bits are all written, let's turn it on.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 7 Jan 2024 06:08:54 +0000 (22:08 -0800)]
altos: Updating pyro format tried to copy entries with no value
Need to check for NO_VALUE before attempting to copy data, otherwise
things will go badly.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 7 Jan 2024 06:07:29 +0000 (22:07 -0800)]
altos/samd21: Enable stdio for USB by default
samd21 usb driver didn't bother to enable stdio for USB for some
reason.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 7 Jan 2024 01:06:58 +0000 (17:06 -0800)]
altos/easytimer-v2: Update comments in flash loader ao_pins.h
No code changes, but the comments were wrong.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 7 Jan 2024 01:03:30 +0000 (17:03 -0800)]
altos/easytimer-v2: Add logging bits
32-byte records with all data in a single record instead of
separate volt/sensor bits.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 16 Mar 2023 17:30:24 +0000 (10:30 -0700)]
altos: Build easytimer-v2 bits
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 16 Mar 2023 17:29:10 +0000 (10:29 -0700)]
altos: Initial easytimer-v2 bits
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 16 Mar 2023 17:25:19 +0000 (10:25 -0700)]
altos: Use BMI088 as z-axis accel as needed
When there's no high-g accel available, use the 'along' axis
to measure acceleration.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 11 Dec 2023 21:44:54 +0000 (13:44 -0800)]
fixup seven segment debug code
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Thu, 16 Nov 2023 16:28:44 +0000 (09:28 -0700)]
Merge branch 'master' of ssh://git.gag.com/scm/git/fw/altos
Bdale Garbee [Thu, 16 Nov 2023 16:28:21 +0000 (09:28 -0700)]
add a paragraph about how to hook up a pressure sensor to an EasyMotor
Keith Packard [Tue, 10 Oct 2023 18:24:45 +0000 (11:24 -0700)]
micropeak: Include firmware in install bits
These are useful for people building their own hardware.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 10 Oct 2023 18:19:54 +0000 (11:19 -0700)]
doc: Use -optimize with asciidoctorpdf
This does some additional compression on the output to make it
smaller.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Wed, 30 Aug 2023 17:52:44 +0000 (11:52 -0600)]
update Releasing with learnings from 1.9.17 release
Bdale Garbee [Thu, 20 Jul 2023 18:02:36 +0000 (12:02 -0600)]
doc: fix a typo in the staging example
Keith Packard [Wed, 30 Aug 2023 16:15:28 +0000 (09:15 -0700)]
Version 1.9.17
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 30 Aug 2023 16:12:34 +0000 (09:12 -0700)]
doc: Release notes for 1.9.17
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Wed, 30 Aug 2023 16:27:39 +0000 (10:27 -0600)]
ao-bringup: be consistent with success text in TeleGPS test script
Bdale Garbee [Mon, 28 Aug 2023 17:44:40 +0000 (11:44 -0600)]
ao-test-igniter: allow anything other than 'open' to be valid so LED tests work
Keith Packard [Fri, 4 Aug 2023 18:54:10 +0000 (11:54 -0700)]
altos: Use ublox-10 mode for TM v4.0
This will only work on a hacked board with a swapped GPS unit.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 22 Jul 2023 07:01:03 +0000 (00:01 -0700)]
altos: Use pyro voltage to check igniters
Instead of using an absolute value for the igniter continuity good
voltage, use 15/16 of the pyro voltage instead. This ensures we scale
with the pyro voltage to find marginal igniters even with high voltage
pyro systems.
This doesn't work on TeleMetrum where we have no pyro voltage
value. On these boards, continue to use a fixed 3.5V value.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 22 Jul 2023 07:00:12 +0000 (00:00 -0700)]
altos: Don't include ao_pyro.h into telelco code
This isn't used at all.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 22 Jul 2023 06:59:07 +0000 (23:59 -0700)]
altos: Add pyro voltage divider values to boards with them
EasyMega and TeleMega have separate measurement circuits for pyro
battery voltages, provide the resistor values.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 22 Jul 2023 06:19:06 +0000 (23:19 -0700)]
altos: Compute igniter good/bad thresholds using 3.5V value
Instead of requiring each product to set the ADC values for good/bad
igniters, compute them based upon a 3.5V value using the ADC
characteristics already present in ao_pins.h.
This changes the threshold used on LPC parts from 400 (0.189V) to
7388.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 Jun 2023 06:15:36 +0000 (23:15 -0700)]
altos/stmf0: Disable ao_boot_check_pin if not in use
This allows rebuilding the boot loader without boot pin support (as
required to debug TeleMini) by only editing ao_pins.h
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 Jun 2023 06:13:29 +0000 (23:13 -0700)]
altos: Add AO_STACK_CANARY to detect stack overflows sometimes
Checks above and below the current task stack at each switch.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 Jun 2023 06:11:01 +0000 (23:11 -0700)]
altos/stm32f042: Increase interrupt stack to 256 bytes
Running the radio on TeleMini in monitor idle mode ended up
overflowing the interrupt stack of 128 bytes. Increase to 256 bytes
and adjust task stack sizes so targets continue to build.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 6 Jun 2023 21:57:53 +0000 (14:57 -0700)]
altoslib: Support Monitor Idle for EasyMini-3
Needed to explicitly support this target even though it was almost the
same as EasyMini v1.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 14 May 2023 17:38:01 +0000 (10:38 -0700)]
altos-mapd: Install systemd dir in arch-independent location
Use $(bindir)/../lib instead of $(libdir) as the latter has the
arch-specific directory added.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Fri, 28 Apr 2023 06:35:28 +0000 (00:35 -0600)]
update Releasing based on 1.9.16 release experiences
Bdale Garbee [Fri, 28 Apr 2023 06:29:01 +0000 (00:29 -0600)]
have TeleGPS production script save RF cal value
Keith Packard [Fri, 28 Apr 2023 03:25:43 +0000 (20:25 -0700)]
Version 1.9.16
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 28 Apr 2023 05:11:30 +0000 (22:11 -0700)]
altosdroid: Deal with Google requiring API version 31
Need to add some magic constants to the build.
Need to support BLUETOOTH_SCAN permission.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Thu, 27 Apr 2023 00:08:09 +0000 (18:08 -0600)]
update TeleGPS v3.0 production script to flash correct firmware versions
Keith Packard [Wed, 26 Apr 2023 23:08:38 +0000 (16:08 -0700)]
Add TeleGPS v3.0 firmware
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 26 Apr 2023 23:04:21 +0000 (16:04 -0700)]
doc: Add 1.9.16 release notes
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Wed, 26 Apr 2023 23:06:42 +0000 (17:06 -0600)]
add production scripts for TeleGPS v3.0
Keith Packard [Wed, 26 Apr 2023 22:46:15 +0000 (15:46 -0700)]
Merge branch 'telegps-v3'
Keith Packard [Tue, 25 Apr 2023 21:11:48 +0000 (14:11 -0700)]
Version 1.9.15.1
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 16 Apr 2023 04:53:28 +0000 (21:53 -0700)]
altos/stm32f04x: Smite the OPL_LAUNCH bit to reset boot config
When rebooting, make sure the option bytes are recomputed based upon
the latest flash configuration, including whether there's a program
loaded. This ensures that we don't end up re-starting the DFU loader
and mangling our ao_boot values. Without this, our flash loader code
wouldn't be able to see the signal to stay in the loader and we'd end
up back in the application.
Of course, this is only necessary if we want to reboot just after
flashing the boot loader without power cycling. Once the chip is power
cycled, it recomputes the option bytes automatically.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 16 Apr 2023 04:50:08 +0000 (21:50 -0700)]
altos/stmf0: Remove some incorrect defines in stm32f0.h
These got copied from the stm32l15x bits
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 10 Apr 2023 03:13:57 +0000 (20:13 -0700)]
telegps: Add unit setting to device configuration dialog
This isn't used by TeleGPS, but is needed to make the config system
work.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 10 Apr 2023 02:41:02 +0000 (19:41 -0700)]
altos/telegps-v3.0: Get LED blinking when GPS locks
Initialize the LED subsystem and assign the green LED to report GPS
lock.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 10 Apr 2023 02:42:31 +0000 (19:42 -0700)]
altos/telegps-v3.0: Use all 6kB of available ram
We need more ram for LED blinking.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 10 Apr 2023 02:41:50 +0000 (19:41 -0700)]
altos/lpc: Support 6k ram targets
Set RAMSIZE in Makefile before including ../lpc/Makefile.defs and it
will select a suitable linker script.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 10 Apr 2023 02:39:37 +0000 (19:39 -0700)]
altos: Make sure storage is setup before starting log
TeleGPS v3.0 uses internal eeprom for config, so storage wasn't
getting setup before doing the telegps-specific init bits. Instead of
worrying about it, just call ao_storage_setup at the top so that
storage is always ready to go.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 9 Apr 2023 23:44:47 +0000 (16:44 -0700)]
altos/telegps-v3.0: Use new MAX 10 support in uBlox driver
Switches to the new packet types as required by this chip.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 9 Apr 2023 23:44:04 +0000 (16:44 -0700)]
altos: Dump GPS dop/course data from 'g' command
This lets monitor idle show more of the GPS status
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 9 Apr 2023 23:42:57 +0000 (16:42 -0700)]
altos/drivers: Support uBlox Max 10 chips
The set of supported packet types has changed from the last chip;
update the driver to switch to new packets.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 9 Apr 2023 23:38:03 +0000 (16:38 -0700)]
altoslib: Parse more GPS monitor data
GPS is being updated to send dop and course data.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 9 Apr 2023 23:37:29 +0000 (16:37 -0700)]
altoslib: Support TeleGPS v3 monitor idle
Needed to deal with ADC difference from STM-based devices.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 28 Mar 2023 20:43:38 +0000 (13:43 -0700)]
altos/telegps-v3.0: Fix SPI bus usage
CC1200 is on SPI 0, M25 is on SPI 1
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 28 Mar 2023 20:32:48 +0000 (13:32 -0700)]
altos/lpcxpresso: Update for 11u24 board
This updates the lpcxpresso demo to support the 11u24 board with
serial connected like telegps v3.0 on p1_13/p1_14
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 28 Mar 2023 18:56:27 +0000 (11:56 -0700)]
altos/lpc: Validate UART pin config
Make sure some UART pin configuration has been selected
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 28 Mar 2023 04:52:27 +0000 (21:52 -0700)]
altos/telegps-v3.0: Use eeprom for config
Avoid wasting space in the SPI flash part for device config
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 28 Mar 2023 04:51:31 +0000 (21:51 -0700)]
altos/lpc: Add support for eeprom on 2x/3x chips
The newer 11U2x and 11U3x parts have enough eeprom to support storing
config data there. Add support for the IAP calls for read/write.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 28 Mar 2023 04:29:06 +0000 (21:29 -0700)]
altos: Build TeleGPS v3.0 by default
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 28 Mar 2023 04:27:43 +0000 (21:27 -0700)]
altos: Add TeleGPS v3.0 support
LPC 11U24FET48 with CC1200 radio. A bit like TeleGPS v1.0 but with different
pin assignments and a different radio chip.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 28 Mar 2023 04:26:41 +0000 (21:26 -0700)]
altos/lpc: Support UART on pio1_13/pio1_14
This is an alternate configuration for this chip.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 28 Mar 2023 04:25:43 +0000 (21:25 -0700)]
altos: Allow ports to use type other than 'void *' for gpio block
LPC uses integers while everyone else has a struct for each gpio block.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 22:39:03 +0000 (14:39 -0800)]
altos/draw: Use damage for lco demo
Do some incremental drawing to demonstrate damage in action
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 22:38:41 +0000 (14:38 -0800)]
altos/draw: Use bitstream fonts for LCO demo
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 22:38:09 +0000 (14:38 -0800)]
altos/draw: Use <> for include files
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 22:36:33 +0000 (14:36 -0800)]
altos/draw: Add vera sans fonts
These work better in 1-bit mode than frutiger
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 22:35:36 +0000 (14:35 -0800)]
altos/draw: Add damage tracking
This will allow more efficient updating of the screen
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 22:11:06 +0000 (14:11 -0800)]
altos/draw: hand-edit 64-pixel 3/5 to avoid jank
These had random-looking pixels hanging off the ends.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 02:55:54 +0000 (18:55 -0800)]
altos/draw: Use fewer fonts in lco sample
Saves some memory
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 02:50:31 +0000 (18:50 -0800)]
altos/draw: Add line test app
There were bugs, now there's a app to check them.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 02:49:47 +0000 (18:49 -0800)]
altos/draw: Split out draw test scaffolding from lco-test.c
Allows it to be reused.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 02:48:54 +0000 (18:48 -0800)]
altos/draw: Inline span fill for polygons
Instead of calling ao_rect, do the clipping by hand
and call ao_solid instead.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 02:48:05 +0000 (18:48 -0800)]
altos/draw: Fix clipping far line end
Make sure the final unclipped pixel gets drawn.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 02:46:40 +0000 (18:46 -0800)]
altos/draw: Check for horiz/vert line when clipping
Horizontal or vertical lines won't step along the minor axis while
clipping.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 02:46:09 +0000 (18:46 -0800)]
altos/draw: Add validation for line drawing
Just make sure it never draws outside the dest.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 00:04:17 +0000 (16:04 -0800)]
altos/draw: Rename test app to 'lco-test'
This seems like a good place to do the LCO UX prototyping
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Feb 2023 00:01:20 +0000 (16:01 -0800)]
altos/draw: Mock up TeleLCO boot sequence
Show logo, progress bar and discovered box numbers during
boot sequence
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 22:59:58 +0000 (14:59 -0800)]
altos/draw: use --gc-sections in demo program
This cleans up all of the unused font bits
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 22:14:56 +0000 (14:14 -0800)]
altos/draw: Rearrange sample LCO screen in draw-test
Place labels at the top, use proportional font so
the voltage values fit.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 21:57:34 +0000 (13:57 -0800)]
altos/draw: Add NotoMono font
This has a zero without a dot in it, so it might
look better on TeleLCO
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 21:47:34 +0000 (13:47 -0800)]
altos/draw: Add transforms to polygon code
This lets the polygons remain constant but have them get
scaled/translated when presented on the screen.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 21:46:15 +0000 (13:46 -0800)]
altos/draw: Convert draw test framework to modern C
Was still using K&R function definitions?
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 21:44:52 +0000 (13:44 -0800)]
altos/draw: Add monospaced font
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 21:42:05 +0000 (13:42 -0800)]
altos/draw: Move font files to subdirectory
It looks like we might end up with a lot of these
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 21:21:24 +0000 (13:21 -0800)]
altos/draw: Add more fonts
Add our logo font and more sizes of Frutiger
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 07:46:25 +0000 (23:46 -0800)]
altos/draw: Add logo
Captures the SVG logo polygons and allows them to be
scaled to suit.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 07:45:25 +0000 (23:45 -0800)]
altos/draw: Use float for polygon coords
This makes polygons look way better.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 06:39:07 +0000 (22:39 -0800)]
altos/draw: Make test drawing app emulate TeleLCO
Draw some numbers for box and pad. Also allow display of a couple of
polygons.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 06:38:33 +0000 (22:38 -0800)]
altos/draw: Only cover ASCII
Skip the rest of latin-1
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 06:37:16 +0000 (22:37 -0800)]
altos/draw: Add poly fill function
Fill polygons using non-zero winding rule.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 26 Feb 2023 03:22:58 +0000 (19:22 -0800)]
altos: Fill in more of the draw code
Get multiple fonts working, allow for variable-pitch fonts.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 16 Feb 2023 23:13:01 +0000 (15:13 -0800)]
Version 1.9.15
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Mon, 20 Feb 2023 00:50:40 +0000 (17:50 -0700)]
ao-bringup: turnon and test scripts for TeleMetrum v4.0 & TeleMega v6.0
Keith Packard [Sun, 19 Feb 2023 00:51:09 +0000 (16:51 -0800)]
ao-tools/ao-flash: Use 'program' instead of 'flash' for samd21
Switch to the program command, which has a 'reset' option, to get the
device back to running after loading the boot loader.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 16 Feb 2023 23:36:30 +0000 (15:36 -0800)]
doc: Add TeleMetrum v4.0 to specs and 1.9.15 release notes
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 16 Feb 2023 23:36:11 +0000 (15:36 -0800)]
altos/telemetrum-v4.0: Add .gitignore
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 16 Feb 2023 23:35:29 +0000 (15:35 -0800)]
Add TeleMetrum v4.0 firmware to releases
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 16 Feb 2023 23:12:24 +0000 (15:12 -0800)]
Add TeleMega v6.0 firmware to release
Signed-off-by: Keith Packard <keithp@keithp.com>