first cut at turnon scripts for EasyTimer v2

[fw/altos] / doc / telemini.inc

diff --git a/doc/telemini.inc b/doc/telemini.inc
index 08893dfba63da04f11c3362f6e3684968846502b..97bca72b462e7529998299b7430dd0884dd84218 100644 (file)
--- a/doc/telemini.inc
+++ b/doc/telemini.inc
@@ -1,8 +1,8 @@
 == TeleMini
 
        .TeleMini v3 Board
-       image::telemini-v3.0-top.jpg[width="5.5in"]
-       image::telemini-v3.0-bottom.jpg[width="5.5in"]
+       image::telemini-v3.0-top.jpg[width=400]
+       image::telemini-v3.0-bottom.jpg[width=400]
 
        TeleMini v3 is 0.5 inches by 1.67 inches.  It was
        designed to fit inside an 18mm air-frame tube, but using it in
@@ -38,16 +38,16 @@
                |Apogee pyro channel connection to pyro circuit
 
                |2
-               |Apogee +
-               |Apogee pyro channel common connection to battery +
+               |Apogee +++
+               |Apogee pyro channel common connection to battery +++
 
                |3
                |Main -
                |Main pyro channel connection to pyro circuit
 
                |4
-               |Main +
-               |Main pyro channel common connection to battery +
+               |Main +++
+               |Main pyro channel common connection to battery +++
 
                |Left
                |Switch Output
@@ -62,11 +62,11 @@
 
                As described above, using an external pyro battery involves
                connecting the negative battery terminal to the flight
-               computer ground, connecting the positive battery terminal to
-               one of the igniter leads and connecting the other igniter
-               lead to the per-channel pyro circuit connection. Because
-               there is no solid ground connection to use on TeleMini, this
-               is not recommended.
+               computer ground, connecting the switched positive battery 
+               terminal to one of the igniter leads and connecting the other 
+               igniter lead to the per-channel pyro circuit connection. 
+               Because there is no solid ground connection to use on 
+               TeleMini, this is not recommended.
 
                The only available ground connection on TeleMini v3 are
                the two mounting holes next to the telemetry
@@ -75,7 +75,9 @@
 
                Connecting the positive battery terminal to the pyro
                charges must be done separate from TeleMini v3, by soldering
-               them together or using some other connector.
+               them together or using some other connector.  Note that you 
+               must include a switch in the pyro battery positive lead for
+               safety!
 
                The other lead from each pyro charge is then inserted into
                the appropriate per-pyro channel screw terminal (terminal 3 for the
@@ -134,8 +136,8 @@
                callsign settings are, you can temporarily force it
                back to the original default values (frequency
                434.550MHz, callsign N0CALL) by connecting a wire
-               between hole 3 and hole 7 on the debug connector. Hole
-               3 has the square pad around it, hole 7 is the one
+               between hole 3 and hole 6 on the debug connector. Hole
+               3 has the square pad around it, hole 6 is the one
                nearest the MS5607 baro sensor, which is a rectangular
                component with a metal cap that has two holes in it.
 
@@ -152,5 +154,5 @@
                power switch.
 
                .TeleMini v1 Board
-               image::telemini-v1-top.jpg[width="5.5in"]
+               image::telemini-v1-top.jpg[width=400]