doc: Add 1.9.18 release notes

[fw/altos] / doc / config-device.inc

diff --git a/doc/config-device.inc b/doc/config-device.inc
index 0ca6afff10e296d89e035402e67baf41e3d9ac18..71ee1c4f573eecba61665ea6cd815649d54b9b1c 100644 (file)
--- a/doc/config-device.inc
+++ b/doc/config-device.inc
@@ -71,6 +71,11 @@ ifdef::radio[]
                flight. When disabled, the radio will not
                transmit anything during flight at all.
 
+       ==== Limit transmit to 10mW
+
+               Reduces transmit power to no more than 10mW. This is
+               useful when operating under some UK radio regulations.
+
        ==== Telemetry baud rate
 
                This sets the modulation bit rate for data
@@ -90,7 +95,7 @@ ifdef::radio[]
                transmission is disabled.
                ifdef::altusmetrum[]
                This option is
-               available on TeleMetrum v2 and TeleMega
+               available on TeleMetrum v2 or newer and TeleMega
                boards. TeleMetrum v1 boards cannot transmit
                APRS packets.
                endif::altusmetrum[]
@@ -118,6 +123,16 @@ ifdef::radio[]
                altitude with Compressed format. Test before
                you fly to see which to use.
 
+       ==== APRS Offset
+       
+               The delay from the top of the minute before sending
+               the first APRS packet of the minute. Coordinating
+               values for this parameter between multiple devices can
+               allow a single receiver to reliably receive APRS
+               packets from multiple devices. Note that this offset only
+               takes effect while the GPS signal is locked so that the
+               transmitting device knows the current time.
+               
        ==== Callsign
 
                This sets the call sign included in each
@@ -161,7 +176,11 @@ ifdef::altusmetrum[]
                is fired first, followed after a two second
                delay by the 'main' channel.
 
-       ifdef::telemetrum,telemega,easymega[]
+               Separation & Apogee::
+               This fires the 'main' channel when the first motor
+               burns out and fires the 'apogee' charge at apogee.
+
+       ifdef::telemetrum,telemega,easymega,easytimer[]
        ==== Pad Orientation
 
                Because they include accelerometers,
@@ -173,15 +192,16 @@ ifdef::altusmetrum[]
                with the antenna pointing aft instead.
 
                Antenna Up::
-               In this mode, the antenna end of the flight
-               computer must point forward, in line with the
-               expected flight path.
+               In this mode, the antenna (or beeper, for devices
+               without an antenna) of the flight computer must point
+               forward, in line with the expected flight path.
 
                Antenna Down::
-               In this mode, the antenna end of the flight
-               computer must point aft, in line with the
-               expected flight path.
-       endif::telemetrum,telemega,easymega[]
+
+               In this mode, the antenna (or beeper, for devices
+               without an antenna) end of the flight computer must
+               point aft, in line with the expected flight path.
+               endif::telemetrum,telemega,easymega,easytimer[]
 
        ==== Beeper Frequency
 
@@ -212,7 +232,7 @@ ifdef::telegps[]
                in the log.
 endif::telegps[]
 
-ifdef::telemega,easymega,telemetrum[]
+ifdef::telemega,easymega,easytimer,telemetrum[]
 
        ==== Calibrate Accelerometer
 
@@ -226,18 +246,18 @@ ifdef::telemega,easymega,telemetrum[]
                Configure Altimeter window and save the new
                calibration values.
 
-endif::telemega,easymega,telemetrum[]
+endif::telemega,easymega,easytimer,telemetrum[]
 
-ifdef::telemega,easymega[]
+ifdef::telemega,easymega,easytimer[]
 
        ==== Configure Pyro Channels
 
                .Additional Pyro Channel Configuration
-               image::configure-pyro.png[width="5.5in"]
+               image::configure-pyro.png[width=400]
 
                This opens a separate window to configure the
-               additional pyro channels available on TeleMega
-               and EasyMega.  One column is presented for
+               additional pyro channels available on TeleMega,
+               EasyMega and EasyTimer.  One column is presented for
                each channel. Each row represents a single
                parameter, if enabled the parameter must meet
                the specified test for the pyro channel to be
@@ -262,6 +282,6 @@ ifdef::telemega,easymega[]
                configuration by pressing the 'Save' button in
                the main Configure Flight Computer window.
 
-               include::pyro-channels.raw[]
+               include::pyro-channels.adoc[]
 
-endif::telemega,easymega[]
+endif::telemega,easymega,easytimer[]