Bdale Garbee [Wed, 31 Mar 2010 05:11:40 +0000 (23:11 -0600)]
initial harness for documentation
Bdale Garbee [Mon, 15 Mar 2010 18:04:18 +0000 (12:04 -0600)]
move gbp.conf into debian/
Keith Packard [Fri, 12 Mar 2010 18:38:26 +0000 (10:38 -0800)]
Merge remote branch 'origin/master'
Keith Packard [Fri, 12 Mar 2010 18:37:32 +0000 (10:37 -0800)]
Document the ao-dumplog '--remote' flag for radio-link downloads
The --remote (or -R) flag uses TeleDongle to fetch data over the radio
command link from TeleMetrum. It's been there for a while, but the man
page failed to mention it.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 12 Mar 2010 18:35:12 +0000 (10:35 -0800)]
Round radio calibration value instead of truncating
The radio calibration function in the bring-up code was truncating the
radio calibration value which caused the resulting frequency to
always measure above the target frequency, instead of trying to get as
close as possible. This change will result in a closer frequency
match, but may sometimes be below the target frequency.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Sat, 6 Mar 2010 03:11:11 +0000 (19:11 -0800)]
update changelogs for Debian build
Bdale Garbee [Fri, 5 Mar 2010 00:33:39 +0000 (17:33 -0700)]
update changelogs for Debian build
Keith Packard [Mon, 1 Mar 2010 02:24:46 +0000 (18:24 -0800)]
Need to duplicate new altitude conversion code in aoview.
Altitude conversion is now done with a smaller table and interpolation
instead of a giant table.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Sun, 28 Feb 2010 00:36:13 +0000 (17:36 -0700)]
update changelogs for Debian build
Keith Packard [Sat, 27 Feb 2010 23:19:33 +0000 (15:19 -0800)]
Merge remote branch 'origin/master'
Keith Packard [Sat, 27 Feb 2010 23:18:47 +0000 (15:18 -0800)]
Add .gitignore for ao-bringup
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 27 Feb 2010 23:14:04 +0000 (15:14 -0800)]
Fix up LED colors for each product.
Different products assign different color LEDs to the two available
LED drivers (P1_0, P1_1). Make the LED color pin assignments
per-product (in ao_pins.h), then deal with not always having a green LED.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 27 Feb 2010 23:11:44 +0000 (15:11 -0800)]
Eliminate deadlock when writing config from radio link
Writing the 'Saved\r\n' string would fill the packet buffer and cause
a flush to occur, which would need to wait for the radio link to
receive and transmit a packet. The radio link always re-fetches the
radio channel number when lighting up the radio, so it need to look in
the config space. If the config mutex was held by the config writing
process while the radio was trying to get the channel number, then
we'd get a deadlock.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 27 Feb 2010 23:10:16 +0000 (15:10 -0800)]
Leave .ihx files in the build directory too - easier to debug that way
sdcdb wants the .ihx and .cdb files in the same directory, so humor it
by copying the .ihx files to the src directory instead of moving them.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Fri, 26 Feb 2010 22:21:12 +0000 (15:21 -0700)]
create a turn on script for lighting up TeleDongle v0.2 boards
Keith Packard [Fri, 26 Feb 2010 18:33:13 +0000 (10:33 -0800)]
Add LED test
Keith Packard [Fri, 26 Feb 2010 00:40:13 +0000 (16:40 -0800)]
Fix and document the ao-rawload --run flag
This allows ram-based programs to be loaded and executed easily.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 26 Feb 2010 00:33:34 +0000 (16:33 -0800)]
Allow product names to have suffixes (like board revisions)
When looking for a board by product name, just look at the prefix of
the name instead of requiring an exact match. This will allow products
to have board version suffixes.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 26 Feb 2010 00:32:57 +0000 (16:32 -0800)]
Add ao_radio_xmit to help test boards without flashing them.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Thu, 25 Feb 2010 00:30:23 +0000 (17:30 -0700)]
update changelogs for Debian build
Bdale Garbee [Thu, 25 Feb 2010 00:29:47 +0000 (17:29 -0700)]
un-muck changelog
Bdale Garbee [Thu, 25 Feb 2010 00:27:51 +0000 (17:27 -0700)]
debugging
Bdale Garbee [Thu, 25 Feb 2010 00:25:28 +0000 (17:25 -0700)]
conditionalize use of git on executability of /usr/bin/git binary
Bdale Garbee [Thu, 25 Feb 2010 00:22:45 +0000 (17:22 -0700)]
update changelogs for Debian build
Bdale Garbee [Thu, 25 Feb 2010 00:22:20 +0000 (17:22 -0700)]
see if this works
Bdale Garbee [Thu, 25 Feb 2010 00:13:29 +0000 (17:13 -0700)]
move git-using variable declaration into the prebuild target
Bdale Garbee [Wed, 24 Feb 2010 23:44:44 +0000 (16:44 -0700)]
update changelogs for Debian build
Bdale Garbee [Wed, 24 Feb 2010 23:43:32 +0000 (16:43 -0700)]
add gawk as a build dependency since strtonum is a gawk extension
Bdale Garbee [Wed, 24 Feb 2010 21:57:26 +0000 (14:57 -0700)]
update changelogs for Debian build
Bdale Garbee [Wed, 24 Feb 2010 21:53:27 +0000 (14:53 -0700)]
update changelogs for Debian build
Keith Packard [Sun, 21 Feb 2010 05:35:43 +0000 (21:35 -0800)]
Must install .map files for ao-load to work
ao-load uses the .map files to rewrite the serial number and other
config parameters into the program flash.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 21 Feb 2010 05:20:05 +0000 (21:20 -0800)]
Add back stack size checking to altos linking phase
This verifies that the stack start specified during the compile
will work with the resulting program
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 21 Feb 2010 05:05:45 +0000 (21:05 -0800)]
Quiet make output.
This borrows ideas from the notmuch project to reduce the command line
clutter seen when compiling or linking stuff.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 21 Feb 2010 04:36:08 +0000 (20:36 -0800)]
Update .gitignore files
Keith Packard [Sun, 21 Feb 2010 04:22:16 +0000 (20:22 -0800)]
Change altos build process to support per-product compile-time changes
This creates per-product subdirectories and recompiles everything for
each product, allowing per-product compile-time changes for things
like peripheral pin assignments and attached serial devices.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 21 Feb 2010 04:21:07 +0000 (20:21 -0800)]
Change barometer conversion code to shrink conversion table
Keith Packard [Sun, 14 Feb 2010 00:42:27 +0000 (16:42 -0800)]
Log GPS data on pad after boost detect.
This wakes up the two GPS reporting tasks and gets them to report out
any existing GPS data to the log file. To make sure the timestamps in
that GPS data are accurate, this also records GPS time on receipt of
the GPS data instead of when that is logged.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 7 Feb 2010 08:25:22 +0000 (00:25 -0800)]
Pull in a bit more data for filtering the start of the boost
Keith Packard [Sun, 7 Feb 2010 08:24:56 +0000 (00:24 -0800)]
Compute daytime using GPS as time base
Keith Packard [Fri, 12 Feb 2010 02:48:56 +0000 (18:48 -0800)]
Missing ao_mutex_put in gps_dump
Keith Packard [Mon, 11 Jan 2010 00:31:50 +0000 (16:31 -0800)]
Switch to using internal cc1111 temperature sensor
v0.2 has no temperature sensor, and several of the v0.1 boards didn't
get a temperature sensor loaded. Use the internal temperature sensor
on the cc1111 in all cases instead.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 10 Jan 2010 06:06:19 +0000 (22:06 -0800)]
Force idle mode by shorting the SPI clock to ground at boot time.
This allows you to override the flight mode detection code in case the
accelerometer calibration is broken somehow. Hold the SPI clock shoted
to ground until the LED comes on, then remove it.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 10 Jan 2010 04:57:48 +0000 (20:57 -0800)]
Add simple gps dump command 'g'
This just dumps out the data in a very simple format to verify the GPS
receiver.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 10 Jan 2010 04:57:29 +0000 (20:57 -0800)]
Remove flash debugging printfs
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 10 Jan 2010 04:42:57 +0000 (20:42 -0800)]
Don't set ao_flash_setup_done until we're actually done.
Because we're accessing this variable outside of the mutex, we need to
make sure it isn't set until the data it covers has been initialized.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 10 Jan 2010 04:04:42 +0000 (20:04 -0800)]
Dump config block from read/write config and flash_status commands
Keith Packard [Sun, 10 Jan 2010 03:46:46 +0000 (19:46 -0800)]
Dump more flash parameters for the flash_status command
Keith Packard [Sun, 10 Jan 2010 01:57:52 +0000 (17:57 -0800)]
Add 'f' command to display flash status register contents
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 9 Jan 2010 17:55:04 +0000 (09:55 -0800)]
Add at45db161d.h header file for new flash part.
Forgot to add this when I added the driver.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 9 Jan 2010 09:29:41 +0000 (01:29 -0800)]
Remove green LED and temp sensor from v0.2 code
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 9 Jan 2010 09:22:06 +0000 (01:22 -0800)]
Add AT45DBxx1D driver
This driver supports the AT45DB011D through AT45DB321D DataFlash
parts as found in TeleMetrum v0.2
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 20 Dec 2009 04:32:18 +0000 (20:32 -0800)]
Remove dbg driver code from telemetrum/teledongle
The only board with debug outputs is the TI dongle at this point, so
the debug modules were disabled in TM and TD some time
ago. Unfortunately, the code was not removed then.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 19 Dec 2009 23:31:36 +0000 (15:31 -0800)]
Ensure that ao_alarm waits at least the specified time
Because the timer tick may happen soon, it's important to delay by
another tick to ensure that we don't wake up early.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 19 Dec 2009 22:03:11 +0000 (14:03 -0800)]
Disable monitor mode before attempting radio test.
If monitor mode is left active, then the radio lock will not be able
to be acquired for the radio test.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Sat, 19 Dec 2009 20:53:38 +0000 (13:53 -0700)]
update changelogs for Debian build
Keith Packard [Sat, 19 Dec 2009 19:34:16 +0000 (11:34 -0800)]
Use ao_radio_get/ao_radio_put in packet code.
The ao_radio_get function both acquires the mutex *and* configures the
radio channel and frequency. Failing to use this in the packet code
would leave the radio frequency unconfigured.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Sat, 19 Dec 2009 19:15:29 +0000 (12:15 -0700)]
update changelogs for Debian build
Bdale Garbee [Sat, 19 Dec 2009 19:05:40 +0000 (12:05 -0700)]
update changelogs for Debian build
Keith Packard [Wed, 16 Dec 2009 07:58:29 +0000 (23:58 -0800)]
Add --cal to man page
Keith Packard [Sun, 6 Dec 2009 03:50:38 +0000 (19:50 -0800)]
Allow radio calibration to be set from ao-load
This moves the initial radio calibration value into const memory where
it will be used if no eeprom configuration value is available, either
on an unprogrammed board with eeprom or a device without an eeprom.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 5 Dec 2009 23:36:12 +0000 (15:36 -0800)]
Re-order config values. Change frequency to cal
Place more often used values at top, and consistently call the radio
value 'calibration' instead of 'frequency'.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Sat, 5 Dec 2009 18:03:42 +0000 (11:03 -0700)]
update changelogs for Debian build
Keith Packard [Sat, 5 Dec 2009 07:38:26 +0000 (23:38 -0800)]
Add radio calibration configuration.
The crystal we use is only good for 20ppm, which generates a fairly
significant error bounds at our RF frequency. This commit adds a
configuration variable that sets the RF frequency control variable so
that the output frequency can be adjusted.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 5 Dec 2009 07:36:54 +0000 (23:36 -0800)]
Make ao_cmd_decimal produce both 32 and 16 bit values.
ao_cmd_lex_u32 is produced in addition to ao_cmd_lex_i so that
functions can easily read 32-bit values from the command line.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 5 Dec 2009 07:35:40 +0000 (23:35 -0800)]
Remove send_serial and serial_baud commands.
No longer useful, and they take up space.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Sat, 5 Dec 2009 04:02:07 +0000 (21:02 -0700)]
update changelogs for Debian build
Keith Packard [Fri, 4 Dec 2009 22:35:39 +0000 (14:35 -0800)]
Change default callsign to "N0CALL"
Bdale Garbee [Thu, 26 Nov 2009 18:18:37 +0000 (11:18 -0700)]
update changelogs for Debian build
Bdale Garbee [Thu, 26 Nov 2009 18:16:04 +0000 (11:16 -0700)]
update changelogs for Debian build
Bdale Garbee [Thu, 26 Nov 2009 18:15:13 +0000 (11:15 -0700)]
change home URL in control file to be the AltOS page
Bdale Garbee [Thu, 26 Nov 2009 17:40:07 +0000 (10:40 -0700)]
fix absolute path in debian/dirs, add Suggests for slim-altusmetrum
Bdale Garbee [Sun, 22 Nov 2009 17:18:44 +0000 (10:18 -0700)]
update changelogs for Debian build
Keith Packard [Sun, 22 Nov 2009 09:10:44 +0000 (01:10 -0800)]
Automatically extract flight number for eeprom and telem filenames.
Extract flight number from either telemetry or eeprom files and use
that in the resulting filenames. To ensure that files remain unique,
add a new field, -seq-%03d. This is appended only when the sequence
number is non-zero as it shouldn't occur in normal usage.
This also eliminates some duplicate filename creation code in the
library and aoview sources.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 22 Nov 2009 08:52:58 +0000 (00:52 -0800)]
ao-postflight: don't try to use missing gps sat data
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 22 Nov 2009 06:12:21 +0000 (22:12 -0800)]
ao-postflight: compute barometric alt for each GPS position
Print that to the --gps file, and use that in the --kml file for the
altitude. Gives a very different picture of our flight tracks,
presumably far more accurate (at least in altitude).
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 22 Nov 2009 06:11:45 +0000 (22:11 -0800)]
Don't crash if --plot isn't passed on ao-postflight command line
Crashing is not nice.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 22 Nov 2009 05:10:09 +0000 (21:10 -0800)]
Convert telemetry file GPS satellite information in cc_log_read
The satellite info wasn't being correctly converted from telemetry
files to the data log structure, so ao-postflight was not seeing it.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 22 Nov 2009 05:09:03 +0000 (21:09 -0800)]
Fix --plot arg handling. Add -all option.
The --plot file name handing is special as the library wants a
filename instead of a stdio file pointer.
Add a --all option that just creates all of the possible outputs.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 22 Nov 2009 04:36:20 +0000 (20:36 -0800)]
Make TD print 0000-00-00 for invalid dates.
This 'shouldn't' happen, but in case it does, I want to know about it.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 22 Nov 2009 04:35:22 +0000 (20:35 -0800)]
Make ao-postflight create filenames using input filenames.
Instead of requiring the user to provide names for the various output
options, just create them from the input name by replacing the extension.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 22 Nov 2009 03:52:26 +0000 (19:52 -0800)]
Document ao-postflight --gps and --kml options.
These were missing from the man page, but included in the --help output.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 22 Nov 2009 02:57:45 +0000 (18:57 -0800)]
Decode HDOP data from skytraq GPS
The hdop data was getting dropped on the floor, but is rather useful
when deciding if the GPS position is crazy or not. This reports HDOP *
5 (giving a useful range of .2-50).
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Fri, 20 Nov 2009 20:19:02 +0000 (13:19 -0700)]
update changelogs for Debian build
Keith Packard [Fri, 20 Nov 2009 20:16:37 +0000 (12:16 -0800)]
Eliminate SiRF state values from ao-view.
With Skytraq not having any visible GPS state information, just
remove this from the display.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 20 Nov 2009 19:56:48 +0000 (11:56 -0800)]
Add GPS date/time output to ao-postflight.
GPS date/time information was already being stored in the log, it just
wasn't getting displayed by ao-postflight.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 20 Nov 2009 19:55:28 +0000 (11:55 -0800)]
Reduce igniter firing time from 500ms to 50ms.
Given that the system will brown-out with the longer pulse, it doesn't
make sense to even try; failure at 50ms probably indicates a short.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Fri, 20 Nov 2009 04:43:13 +0000 (21:43 -0700)]
fix typo in comment
Bdale Garbee [Fri, 20 Nov 2009 18:44:06 +0000 (11:44 -0700)]
update changelogs for Debian build
Keith Packard [Mon, 16 Nov 2009 00:20:18 +0000 (16:20 -0800)]
Stop using SiRF state info.
With the switch to the skytraq GPS unit, we don't have the same level
of detail in the GPS stream, so stop reporting that in the telemetry
stream, in the UI and writing it to eeprom.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 16 Nov 2009 00:04:41 +0000 (16:04 -0800)]
Add date to GPS data, captured from GPRMC packet.
Pull the date out of the GPS stream and send it over the telemetry
link and write it to the eeprom.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 15 Nov 2009 23:59:01 +0000 (15:59 -0800)]
Add flight number to telemetry stream.
This makes it easier to tie the telemetry and eeprom files together as
they're now both labeled with serial and flight numbers, which should
be unique.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 15 Nov 2009 23:53:01 +0000 (15:53 -0800)]
Switch order of serial/flight in ao-postflight summary
Keith Packard [Sun, 15 Nov 2009 23:51:58 +0000 (15:51 -0800)]
Enable telemetry receive in ao_view
Keith Packard [Sun, 15 Nov 2009 06:24:37 +0000 (22:24 -0800)]
Share telemetry parsing code in cc library.
ao-view had a private copy of the telemetry parsing code which
included the ability to parse the newer version of that file. Those
changes have been moved to the library version and the private copy removed.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 15 Nov 2009 06:24:09 +0000 (22:24 -0800)]
Provide a dummy 'uninstall' target in the src directory.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 15 Nov 2009 06:17:24 +0000 (22:17 -0800)]
Loosen tolerances for main->landed transition
Detecting that the rocket has landed is required for the system to
flush the eeprom log and re-enable the RDF beacon. This patch changes
the landed state entry requirements for the accelerometer to require
only that the accelerometer stay within a quarter of a g (down from
1/10g) and changes the testing interval from 20 seconds to 5
seconds.
The requirement that the barometric altitude be within 1000m of the
launch altitude and that the barometer change by no more than 0.05kPa
are unchanged.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 15 Nov 2009 00:35:12 +0000 (16:35 -0800)]
ao-postflight: fix sloppy gps sat data realloc code (was crashing).
Realloc'ing the wrong data, and failing to set the realloc'ed size was
causing ao-postflight to crash while reading long logs.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 6 Nov 2009 06:11:59 +0000 (22:11 -0800)]
Return radio to telemetry settings when packet system closed.
To receive telemetry after disabling the packet system, the radio must
be reconfigured for telemetry mode.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 6 Nov 2009 05:45:00 +0000 (21:45 -0800)]
Add reboot command.
This resets the processor using the watchdog timer.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 6 Nov 2009 05:44:31 +0000 (21:44 -0800)]
Add Watchdog Timer Control register definitions
Signed-off-by: Keith Packard <keithp@keithp.com>