creating index page EasyTimer/v1
[web/altusmetrum] / production.mdwn
1 # Altus Metrum Units Constructed
2
3 This page contains Bdale's notes about each unit of [TeleMetrum](TeleMetrum/) 
4 and [TeleDongle](TeleDongle/) assembled to date.
5
6 ## sn 1 ##
7
8 Full load of v0.1 PCB, two cuts and jumps to rewire P1_2 to be SPI memory 
9 chip select, R14 and R15 loaded with 56k, 10k tacked from each to 
10 ground.  R17 replaced with short circuit, R18 removed.
11
12 Installed in Bdale's Vertical Assault.  First unit to be flown on 
13 2009.04.19, on a Cesaroni J335.
14
15 Successfully flew Bdale's rebuilt Horizon dual-deploy at Hudson Ranch on
16 2009.07.18 with a MAWD as backup.  The first dual-deploy flight with a TM
17 board in control of ejection charges!
18
19 ## sn 2 ##
20
21 Full load of v0.1 PCB, two cuts and jumps to rewire P1_2 to be SPI memory 
22 chip select, R14 and R15 loaded with 56k, 10k tacked from each to 
23 ground.
24
25 Delivered to Keith Packard for firmware development and use.  Flown twice
26 on 10 May 2008 in Keith's Grappler to about 45m on Estes D12-3 motors.
27
28 Flew in Keith's Little Dog Dual Deploy at Mile High Mayhem as a payload.  The
29 ascent was pretty but the rocket failed to deploy and lawn-darted.  The battery
30 and screw terminal block connectors got more or less torn off, but the rest
31 of the board survived and good data was recovered from the flight.
32
33 Repaired by Bdale, sent back to Keith on 7 July 2009.  Keith reported the
34 baro sensor as flakey, it was replaced in October 2009 prior to 
35 NCR Octoberfest.
36
37 ## sn 3 ##
38
39 Full load of v0.1 PCB on 2009.04.22, two cuts and jumps to rewire P1_2 
40 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked 
41 from each to ground.
42
43 Installed in Bdale's Vertical Assault after sn 1 moved to Horizon, but never
44 flown there.
45
46 Pulled and given to Keith to take home from Mayhem.
47
48 Lost in Keith's Nike which was lost for a while after an apparently nominal 
49 flight in June 2009 at Brothers, Oregon.  Rocket was later found and this unit
50 is reportedly still in good condition.
51
52 ## sn 4 ##
53
54 Full load of v0.1 PCB on 2009.04.22, two cuts and jumps to rewire P1_2 
55 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked 
56 from each to ground.
57
58 Installed in Robert's Lil Nuke.
59
60 Lost at Hudson Ranch 2009.07.18 when we forgot to tape the nose cone on and
61 both it and the electronics sled came out at apogee and were not recovered.
62
63 ## sn 5 ##
64
65 Partial "ground" load of v0.1 PCB on 2009.04.23 plus beeper and serial 
66 connector for use as TeleDongle or for TeleTerra prototype.
67
68 Bdale's TeleDongle.
69
70 Keith added acrylic LED light pipes and a LiPo for use in RDF after flight.
71
72 ## sn 6 ##
73
74 Partial "ground" load of v0.1 PCB on 2009.04.23 for use as TeleDongle.
75
76 Keith's TeleDongle.
77
78 Keith added acrylic LED light pipes and a LiPo for use in RDF after flight.
79
80 ## sn 7 ##
81
82 Full load of v0.1 PCB on 2009.08.08, two cuts and jumps to rewire P1_2 
83 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked 
84 from each to ground.
85
86 Pulled from Vertical Assault (never flew there) and taken to Keith in Japan
87 in October 2009 as replacement.
88
89 ## sn 8 ##
90
91 Full load of v0.1 PCB on 2009.08.08, two cuts and jumps to rewire P1_2 
92 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked 
93 from each to ground.
94
95 Delivered to Keith in early November 2009.
96
97 ## sn 9 ##
98
99 Full load of v0.1 PCB on 2009.08.15, two cuts and jumps to rewire P1_2 
100 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked 
101 from each to ground.
102
103 Installed in Bdale's Trick-o-Treat 98mm airframe.
104
105 ## sn 10 ##
106
107 Full load of v0.1 PCB on 2009.08.15, two cuts and jumps to rewire P1_2 
108 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked 
109 from each to ground.
110
111 Installed in Robert's Lil Nuke.
112
113 ## sn 11 ##
114
115 Full load of v0.1 PCB on 2009.08.15, two cuts and jumps to rewire P1_2 
116 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked 
117 from each to ground.  Accelerometer loaded is MMA2204EG 100G unit!
118
119 In G-Spot, this accelerometer recorded 52.8 gee acceleration on a
120 Cesaroni pro29 H399 reload at NCR Oktoberfest 2009!
121
122 Beeper failed after a hard landing, replaced 2010.02.06.
123
124 ## sn 12 ##
125
126 Full load of v0.1 PCB on 2009.11.05, two cuts and jumps to rewire P1_2 
127 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked 
128 from each to ground.  Accelerometer loaded is MMA2204EG 100G unit!
129
130 ## sn 13 ##
131
132 Full load of v0.1 PCB on 2009.11.05, two cuts and jumps to rewire P1_2 
133 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked 
134 from each to ground.
135
136 Modified 2009.11.20 to:
137
138 * use TC1055-3.3VCT713 100ma regulator proposed for v0.2
139 * route 3.3V instead of v_lipo to the serial connector for SkyTraq GPS
140 * use v_lipo for pyro voltage instead of 5V with 1000uF capacitor
141 * added 100uF 1206 capacitor on 3.3V rail
142
143 In this configuration, flew two textbook perfect flights on 2009.11.21 at
144 Hudson Ranch in Trick-O-Treat on J motors.
145
146 Modified 2011.11.13 to:
147
148 * test ADXL78 accelerometer functionality for v1.2 build
149 * use 3.3k instead of 10k for R2 and R3, to eliminate power-on pyro glitching
150
151 ## sn 14 ##
152
153 Full load of v0.1 PCB on 2009.11.05, two cuts and jumps to rewire P1_2 
154 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked 
155 from each to ground.
156
157 Modified 2010.10.18:
158
159 * R10 changed to 27k to allow keithp to test use of 1.25V ADC internal 
160   reference with the accelerometer
161
162 Delivered to keithp on 2010.10.19.
163
164 Modifed by keithp on 2011.03.30 to have 3.3V on the serial connector power pin.
165
166 ## sn 15 ##
167
168 Partial "ground" load of v0.1 PCB on 2009.11.18 for use as TeleDongle.
169
170 ## sn 16 ##
171
172 Partial "ground" load of v0.1 PCB on 2009.11.18 for use as TeleDongle.
173
174 ## sn 17-21 ##
175
176 Full load of TeleMini v0.1 PCBs on 2011.03.07.  Minor variations due to 
177 parts availability, as follows:
178
179 * sn 17-18 have TXC oscillators, sn 19-21 have Abracom
180 * sn 21 is missing the dual LED 
181
182 ## sn 25-26 ##
183
184 Full load of TeleTerra v0.1 PCBs on 2010.10.31
185
186 ## sn 27-31 ##
187
188 Full load of TeleNano v0.1 PCBs on 201103.09.  sn 27 has TXC oscillator, all
189 others have Abracom, no other significant variations.
190
191 ## sn 32-33 ##
192
193 Full load of TeleMini v0.2 PCBs on 2011.05.04.
194
195 ## sn 34-36 ##
196
197 Full load of TeleScience v0.1 PCBs on 2011.05.05.
198
199 ## sn 37-38 ##
200
201 Full load of TeleBT v0.1 PCBs on 2011.05.06.
202
203 ## sn 39-42 ##
204
205 Full load of TelePyro v0.1  PCBs on 2011.09.20, except only sn 39 and 40
206 have magnetic sensors since I only have two samples of the now-obsolete part.
207
208 ## sn 43-45 ##
209
210 Full load of TeleScience v0.1 PCBs on 2011.09.22.
211
212 ## sn 46-48 ##
213
214 Full load of TeleTerra v0.2 PCBs on 2011.10.23.
215
216 ## sn 49-50 ##
217
218 Full load of TeleShield v0.1 PCBs on 2012.01.03, using 3.15V reset controller
219 and the less-good crystals.
220
221 ## sn 51 ##
222
223 Full load of TeleMetrum v0.2 PCB on 2010.01.09, with 100g accel and screw 
224 terminals.
225
226 Installed in G-Spot on 2010.02.06.
227
228 ## sn 52 ##
229
230 Full load of TeleMetrum v0.2 PCB on 2010.01.09, with 50g accel and Tyco header.
231
232 Went home with Keith from LCA 2010 in Wellington.
233
234 ## sn 53 ##
235
236 Full load of TeleMetrum v0.2 PCB on 2010.01.09, with 40g accel and screw 
237 terminals.
238
239 ## sn 54-56 ##
240
241 Prototypes of TeleMetrum v1.1 loaded with the newer Venus 638 chips for 
242 evalutation, loaded as part of the production v1.1 run by 
243 [Advanced Circuits](http://4pcb.com), received 2011.01.06.
244
245 ## sn 57-60 ##
246
247 Full load of TeleBT v0.2 PCBs on 2012.01.07.
248
249 ## sn 61-63 ##
250
251 Full load of TeleShield v0.1 PCBs on 2012.01.13.
252
253 ## sn 64-65 ##
254
255 MegaMetrum v0.1 PCBs on 2012.03.31, with 2 megabyte flash parts and no 
256 high-g accel.
257
258 ## sn 66 ##
259
260 TeleFire v0.1 PCB built by Keith on 2012.08.23.
261
262 ## sn 67 ##
263
264 TeleLCO v0.1 PCB built by Keith on 2012.08.26.
265
266 ## sn 68-70 ##
267
268 MegaMetrum v0.1 PCBs on 2012.08.28.
269
270 ## sn 71-73 ##
271
272 TeleBT v0.3 2012.12.19.
273
274 ## sn 74-76 ##
275
276 MegaDongle v0.2 2012.12.27.
277
278 ## sn 77-79 ##
279
280 TeleScience v0.2 2013.01.12.
281
282 ## sn 80-82 ##
283
284 TeleGPS v0.1 2013.03.20
285
286 ## sn 83-85 ##
287
288 TeleMega v0.3 2013.05.07.  sn 85 has cc1125, the others have cc1120.
289
290 ## sn 86-88 ##
291
292 EasyMini v0.1 2013.05.19.
293
294 ## sn 89-91 ##
295
296 TeleMini v1.1 2013.05.22.
297
298 ## sn 92-93 ##
299
300 TeleMetrum v1.9 2013.08.27
301
302 ## sn 94-95 ##
303
304 TeleMega v0.4 P 2013.08.28
305
306 ## sn 96 ##
307
308 TeleMini v1.1 2013.08.25. From Phoenix panel.
309
310 ## sn 97-98 ##
311
312 TeleMini v1.1 2013.09.15. From Phoenix panel.
313
314 ## sn 100-207 ##
315
316 First production run of 108 pieces of TeleDongle v0.2 by 
317 [Advanced Circuits](http://4pcb.com), received 2010.02.25.
318
319 ## sn 208-261 ##
320
321 First production run of 54 pieces of TeleMetrum v1.0 by
322 [Advanced Circuits](http://4pcb.com), received 2010.04.08.
323
324 ## sn 262-366 ##
325
326 Production run of 105 pieces of TeleMetrum v1.1 by
327 [Advanced Circuits](http://4pcb.com), received 2011.01.06.
328
329 ## sn 367-690 ##
330
331 Production run of 324 pieces of TeleDongle v0.2 by 
332 [Advanced Circuits](http://4pcb.com), received 2011.03.21.
333
334 ## sn 691-834 ##
335
336 Production run of 144 pieces of TeleMini v1.0 by
337 [Advanced Circuits](http://4pcb.com), received 2011.07.25.
338
339 ## sn 835-941 ##
340
341 Production run of 107 pieces of TeleMetrum v1.2 by
342 [Advanced Circuits](http://4pcb.com), received 2011.12.15.
343
344 ## sn 942-1049 ##
345
346 Production run of 108 pieces of TeleMetrum v1.2b by
347 [Advanced Circuits](http://4pcb.com), received 2012.10.29.
348
349 ## sn 1050-1169 ##
350
351 Production run of 120 pieces of TeleBT v1.0 by
352 [Advanced Circuits](http://4pcb.com), received 2013.04.08.  All above 
353 approximately sn 1050 were lost in the fire.
354
355 ## sn 1070-1189 ##
356
357 Production run of 120 pieces of TeleBT v1.1 by
358 [Advanced Circuits](http://4pcb.com), received 2013.08.22.  This batch
359 later determined to have been built with "suspect" TI cc1111 chips.
360
361 ## sn 1190-1213 ##
362
363 Production run of 24 pieces of EasyMini v1.0 by
364 keithp. Build started 2013.10.05
365
366 ## sn 1214-1263 ##
367
368 Production run of 50 pieces of TeleMega v1.0 by
369 [Advanced Circuits](http://4pcb.com), received 2013.12.09.
370
371 ## sn 99 ##
372
373 TeleMini v1.1 from phoenix panel
374
375 ## sn 1264-1269 ##
376
377 Production run of 6 EasyMini v1.0 by keithp
378
379 ## sn 1270-1377 ##
380
381 Production run of 108 pieces of TeleMetrum v2.0 by
382 [Advanced Circuits](http://4pcb.com), received 2014.01.24.
383
384 ## sn 1378-1593 ##
385
386 Production run of 216 pieces of TeleDongle v0.2b byy
387 [Advanced Circuits](http://4pcb.com), received 2014.01.27.  This batch
388 later determined to have been built with "suspect" TI cc1111 chips.
389
390 ## sn 1594-1602 ##
391
392 Production run of 9 EasyMini v1.0 by keithp 2014.01.30
393  
394 ## sn 1603-1611 ##
395
396 Production run of 9 EasyMini v1.0 by keithp. 2014.02.04
397
398 ## sn 1612-1661 ##
399
400 Production run of 50 pieces of TeleMega v1.0 by
401 [Advanced Circuits](http://4pcb.com), received 2014.01.13.
402
403 ## sn 1662-1664 ##
404
405 Prototype build of 3 TeleGPS v0.3 by Bdale 2014.03.11.
406
407 ## sn 1665-1864 ##
408
409 Production run of 200 pieces of EasyMini v1.0 by
410 [Advanced Circuits](http://4pcb.com), received 2014.04.02.
411
412 ## sn 1865-1867 ##
413
414 Prototype build of 3 USBrelay v0.1 by Bdale 2014.05.07.
415
416 ## sn 1868-1870 ##
417
418 Prototype build of 3 FCtester v0.1 by Bdale 2014.05.11.
419
420 ## sn 1871-1873 ##
421
422 Prototype build of 3 EasyMega v0.1 by Bdale 2014.05.14
423
424 ## sn 1874-1981 ##
425
426 Production run of 108 pieces of TeleGPS v1.0 by
427 [Advanced Circuits](http://4pcb.com), received 2014.05.21.
428
429 ## sn 1982-1983 ##
430
431 Build 2 TeleFire v0.2 by Keith 2014.07.12
432
433 ## sn 1984-2083 ##
434
435 Production run of 100 pieces of EasyMega v1.0 by
436 [Advanced Circuits](http://4pcb.com), received 2014.08.14.
437
438 ## sn 2084-2086 ##
439
440 Prototype build of 3 TeleDongle v1.9 by Keithp 2014.11.06
441
442 ## sn 2087-2302 ##
443
444 Production run of 216 pieces of TeleMetrum v2.0b by
445 [Advanced Circuits](http://4pcb.com), received 2014.11.26.
446
447 ## sn 2303-2402 ##
448
449 Production run of 100 pieces of TeleMega v1.0b by
450 [Advanced Circuits](http://4pcb.com), received 2014.12.06.
451
452 ## sn 2403-2406 ##
453
454 Prototype build of 3 USBtrng v2.0 by Keithp 2015.01.25
455
456 ## sn 2407-2409 ##
457  
458 Prototype build of 3 TeleBT v2.0 by bdale 2015.01.29
459
460 ## sn 2410-2517 ##
461
462 Production run of 108 pieces of TeleDongle v3.0 by
463 [Advanced Circuits](http://4pcb.com), received 2015.05.04.
464
465 ## sn 2518-2529 ##
466
467 Production run of 12 pieces of TeleMini v1.0 by keithp 2015.02.13
468
469 ## sn 2530-2541 ##
470
471 Prototype built of 12 USBtrng v3.0 by keithp 2015.02.22
472
473 ## sn 2542-2667 ##
474
475 Production run of 126 pieces of TeleBT v3.0 by
476 [Advanced Circuits](http://4pcb.com), received 2015.07.16.
477
478 ## sn 2668-2917 ##
479
480 Production run of 250 pieces of TeleDongle v3.0 by
481 [Advanced Circuits](http://4pcb.com), received 2015.10.21.
482
483 ## sn 2918-2920 ##
484
485 Prototype run of 3 pieces of TeleFireTwo v0.1 by keithp 2015.12.16
486
487 ## sn 2921-2923 ##
488
489 Prototype run of 3 pieces of TeleLCOTwo v0.1 by keithp 2015.12.16
490
491 ## sn 2924-3031 ##
492
493 Production run of 108 pieces of TeleGPS v1.0 by
494 [Advanced Circuits](http://4pcb.com), received 2016.01.06.
495
496 ## sn 3032-3131 ##
497
498 Production run of 100 pieces of TeleMega v2.0 by
499 [Advanced Circuits](http://4pcb.com), received 2016.01.06.
500
501 ## sn 3132-3133 #
502
503 Production run of 2 pieces of TeleMini v1.0 by
504 keithp, built 2016.01.16
505
506 ## sn 3134-3393 #
507
508 Production run of 260 pieces of EasyMini v1.0 by
509 [Advanced Circuits](http://4pcb.com), received 2016.01.26.
510
511 ## sn 3394-3396 #
512
513 Prototype run of 3 TeleLCOTwo by
514 keithp, built 2016.04.05
515
516 ## sn 3397-3398 #
517
518 Prototype run of 2 TeleFireTwo v0.2 by
519 keithp, built 2016.04.06
520
521 ## sn 3399-3402 ##
522
523 Prototype run of 4 TeleFireTwo v1.1 by
524 keithp, built 2016.06.12
525
526 ## sn 3403-3502 ##
527
528 Production run of 100 pieces of TeleMega v2.0 by
529 [Advanced Circuits](http://4pcb.com), received 2016.12.16.
530
531 ## sn 3503-3628 ##
532
533 Production run of 126 pieces of TeleMetrum v2.0b by
534 [Advanced Circuits](http://4pcb.com), received 2017.02.26.
535
536 ## sn 3629-3631 ##
537
538 Prototype build of 3 pieces of TeleGPS v2.0 by Bdale on 2017.04.13.
539
540 ## sn 3632-3634 ##
541
542 Prototype build of 3 pieces of TeleFireTwo v1.0 by Bdale on 2017.04.18.
543
544 ## sn 3635-3685 ##
545
546 Production run of 50 TeleMini v3.0 by
547 [Seeed Studios](https://www.seeedstudio.com/), received 2017.04.17.
548
549 ## sn 3686-3688 ##
550
551 Prototype build of 3 pieces of TeleBT v4.0 beta 1 by Bdale on 2017.04.25.
552
553 ## sn 3689-3938 ##
554
555 Production run of 250 pieces of TeleBT v4.0 by
556 [Advanced Circuits](http://4pcb.com), received 2017.07.21.
557
558 ## sn 3939 ##
559
560 Errant TeleDongle v3.0 found in Bdale's collection.
561
562 ## sn 3940-4189 ##
563
564 Production run of 250 pieces of TeleGPS v2.0 by
565 [Advanced Circuits](http://4pcb.com), received 2017.09.16.
566
567 ## sn 4190-4439 ##
568
569 Production run of 250 pieces of TeleMega v3.0 by
570 [Advanced Circuits](http://4pcb.com), received 2017.11.30.
571
572 ## sn 4440-4939 ##
573
574 Production run of 500 pieces of EasyMini v2.0 by
575 [Advanced Circuits](http://4pcb.com), received 2017.12.19.
576
577 ## sn 4940-5137 ##
578
579 Production run of 198 pieces of TeleMetrum v2.0b by
580 [Advanced Circuits](http://4pcb.com), received 2018.03.10.
581
582 ## sn 5138-5141 ##
583
584 Hand build of 4 pieces of TeleLCO v2.0 by Bdale on 2017.05.27.
585
586 ## sn 5142-5145 ##
587
588 Hand build of 4 pieces of TeleFireEight v1.0 by Bdale on 2017.05.30.
589
590 ## sn 5146-5395 ##
591
592 Production run of 250 pieces of TeleDongle v3.0 by
593 [Advanced Circuits](http://4pcb.com), received 2018.09.26.
594
595 ## sn 5396-5398 ##
596
597 Prototype build of 3 pieces of EasyMega v2 proto 1 by Bdale on 2018.10.12.
598
599 ## sn 5400-5649 ##
600
601 Production run of 250 pieces of EasyMega v2 by
602 [Advanced Circuits](http://4pcb.com), received 2018.12.27.
603
604 ## sn 5650-5699 ##
605
606 Production run of 50 pieces of TeleFireEight v2 by
607 [Advanced Circuits](http://4pcb.com), received 2019.01.25.
608
609 ## sn 5700-5701 ##
610
611 Prototype build of 2 pieces of TeleFireOne v2 by Bdale on 2019.02.16
612
613 ## sn 5702-5703 ##
614
615 Prototype build of 2 pieces of TeleStatic v3 by Bdale on 2019.04.21
616
617 ## sn 5704-5728 ##
618
619 Production build of 25 pieces of TeleLCO v2.1 by 
620 [Advanced Circuits](http://4pcb.com)
621
622 ## sn 5729-5980 ##
623
624 Production build of 252 pieces of TeleMetrum v3.0 by 
625 [Advanced Circuits](http://4pcb.com)
626
627 ## sn 5981-6480 ##
628
629 Production build of 500 pieces of EasyMini v2.0a by 
630 [Advanced Circuits](http://4pcb.com)
631
632
633 ## sn 6481-6580 ##
634
635 Production build of 100 pieces of TeleMini v3.0a by
636 [Seeed Studios](https://www.seeedstudio.com/), received 2020.01.21.
637
638 ## sn 6581-6830 ##
639
640 Production build of 250 pieces of TeleMega v4.0 by
641 [Advanced Circuits](http://4pcb.com), received 2020.02.12
642
643 ## sn 6831-6833 ##
644
645 Prototype build of 3 pieces of EasyTimer v1 by Bdale on 2020.04.06
646
647 ## sn 6834-7083 ##
648
649 Production build of 250 pieces of EasyTimer v1 by
650 [Advanced Circuits](http://4pcb.com), received 2020.05.28
651