git.gag.com Git - hw/telelco/search

2012-07-30	Keith Packard	switch to STM152LRBT6 Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-07-24	Keith Packard	Add serial debug connector for cc1111 Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-07-24	Keith Packard	Clean up pcb -- unthermal a couple vias, erase dirt Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-07-24	Keith Packard	Route complete with cc1111 radio again Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-07-23	Keith Packard	Switch back to the cc1111 for a radio Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-07-22	Keith Packard	Move LEDs to back of board. Unthermal vias Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-07-16	Keith Packard	Add π filters on all links between CPU and CC1120 Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-07-10	Keith Packard	Move ink around Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-07-10	Keith Packard	Switch to CC1120 radio. Add reset controller Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-22	Keith Packard	Use 64-pin STM32L processor. Shrink board to 4.5 x... Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-13	Keith Packard	Add cap on vlcd line, disconnect vlcd from +3.3V Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-13	Keith Packard	Ignore DRC on outline. Shift USB cutout to center on... Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-13	Keith Packard	Add 22-ohm resistors to USB data lines Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-09	Keith Packard	Move ink for serial number down under the license. Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-09	Keith Packard	Use all through-hole LEDs. Add mounting holes. Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-09	Keith Packard	Nearly route complete with LCD and knobs on backside...	commit \| commitdiff \| tree
2012-06-09	Keith Packard	Add footprint for USB bare wires Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-09	Keith Packard	Replace PEC11L rotary switch with PEC11 version Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-09	Keith Packard	Update with battery charger, new STM debug etc Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-09	Keith Packard	Move LCD and switches to back side of board Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-08	Keith Packard	Switch from PEC11L to PEC11 for rotary switch Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-07	Keith Packard	Shrink PCB to 4.5" x 4.5" Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-07	Keith Packard	Create PCB layout Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-07	Keith Packard	Add packages and set footprints Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree
2012-06-07	Keith Packard	Start telelco work. Signed-off-by: Keith Packard <keithp@keithp.com>	commit \| commitdiff \| tree

lco end of wireless launch system

RSS Atom