release-notes-0.8.html \
release-notes-0.9.html \
release-notes-0.9.2.html \
- release-notes-1.0.html
+ release-notes-1.0.1.html
RELNOTES_XSL=$(RELNOTES:.html=.xsl)
HTML=altusmetrum.html altos.html telemetry.html $(RELNOTES)
--- /dev/null
+<?xml version="1.0" encoding="utf-8" ?>
+<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook XML V4.5//EN"
+"/usr/share/xml/docbook/schema/dtd/4.5/docbookx.dtd">
+
+<article>
+ <para>
+ Version 1.0.1 is a major release, adding support for the TeleMini
+ device and lots of new AltosUI features
+ </para>
+ <para>
+ AltOS Firmware Changes
+ <itemizedlist>
+ <listitem>
+ Add TeleMini v1.0 support. Firmware images for TeleMini are
+ included in AltOS releases.
+ </listitem>
+ <listitem>
+ Change telemetry to be encoded in multiple 32-byte packets. This
+ enables support for TeleMini and other devices without requiring
+ further updates to the TeleDongle firmware.
+ </listitem>
+ <listitem>
+ Support operation of TeleMetrum with the antenna pointing
+ aft. Previous firmware versions required the antenna to be
+ pointing upwards, now there is a configuration option allowing
+ the antenna to point aft, to aid installation in some airframes.
+ </listitem>
+ <listitem>
+ Ability to disable telemetry. For airframes where an antenna
+ just isn't possible, or where radio transmissions might cause
+ trouble with other electronics, there's a configuration option
+ to disable all telemetry. Note that the board will still
+ enable the radio link in idle mode.
+ </listitem>
+ <listitem>
+ Arbitrary frequency selection. The radios in Altus Metrum
+ devices can be programmed to a wide range of frequencies, so
+ instead of limiting devices to 10 pre-selected 'channels', the
+ new firmware allows the user to choose any frequency in the
+ 70cm band. Note that the RF matching circuit on the boards is
+ tuned for around 435MHz, so frequencies far from that may
+ reduce the available range.
+ </listitem>
+ <listitem>
+ Kalman-filter based flight-tracking. The model based sensor
+ fusion approach of a Kalman filter means that AltOS now
+ computes apogee much more accurately than before, generally
+ within a fraction of a second. In addition, this approach
+ allows the baro-only TeleMini device to correctly identify
+ Mach transitions, avoiding the error-prone selection of a Mach
+ delay.
+ </listitem>
+ </itemizedlist>
+ </para>
+ <para>
+ AltosUI Changes
+ <itemizedlist>
+ <listitem>
+ Wait for altimeter when using packet mode. Instead of quicly
+ timing out when trying to initialize a packet mode
+ configuration connection, AltosUI now waits indefinitely for
+ the remote device to appear, providing a cancel button should
+ the user get bored. This is necessary as the TeleMini can only
+ be placed in "Idle" mode if AltosUI is polling it.
+ </listitem>
+ <listitem>
+ Add main/apogee voltage graphs to the data plot. This provides
+ a visual indication if the igniters fail before being fired.
+ </listitem>
+ <listitem>
+ Scan for altimeter devices by watching the defined telemetry
+ frequencies. This avoids the problem of remembering what
+ frequency a device was configured to use, which is especially
+ important with TeleMini which does not include a USB connection.
+ </listitem>
+ <listitem>
+ Monitor altimeter state in "Idle" mode. This provides much of
+ the information presented in the "Pad" dialog from the Monitor
+ Flight command, monitoring the igniters, battery and GPS
+ status withing requiring the flight computer to be armed and
+ ready for flight.
+ </listitem>
+ <listitem>
+ Pre-load map images from home. For those launch sites which
+ don't provide free Wi-Fi, this allows you to download the
+ necessary satellite images given the location of the launch
+ site. A list of known launch sites is maintained at
+ altusmetrum.org which AltosUI downloads to populate a menu; if
+ you've got a launch site not on that list, please send the
+ name of it, latitude and longitude along with a link to the
+ web site of the controlling club to the altusmetrum mailing list.
+ </listitem>
+ <listitem>
+ Flight statistics are now displayed in the Graph data
+ window. These include max height/speed/accel, average descent
+ rates and a few other bits of information. The Graph Data
+ window can now be reached from the 'Landed' tab in the Monitor
+ Flight window so you can immediately see the results of a
+ flight.
+ </listitem>
+ </itemizedlist>
+ </para>
+</article>
+++ /dev/null
-<?xml version="1.0" encoding="utf-8" ?>
-<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook XML V4.5//EN"
-"/usr/share/xml/docbook/schema/dtd/4.5/docbookx.dtd">
-
-<article>
- <para>
- Version 1.0 is a major release, adding support for the TeleMini
- device and lots of new AltosUI features
- </para>
- <para>
- AltOS Firmware Changes
- <itemizedlist>
- <listitem>
- Add TeleMini v1.0 support. Firmware images for TeleMini are
- included in AltOS releases.
- </listitem>
- <listitem>
- Change telemetry to be encoded in multiple 32-byte packets. This
- enables support for TeleMini and other devices without requiring
- further updates to the TeleDongle firmware.
- </listitem>
- <listitem>
- Support operation of TeleMetrum with the antenna pointing
- aft. Previous firmware versions required the antenna to be
- pointing upwards, now there is a configuration option allowing
- the antenna to point aft, to aid installation in some airframes.
- </listitem>
- <listitem>
- Ability to disable telemetry. For airframes where an antenna
- just isn't possible, or where radio transmissions might cause
- trouble with other electronics, there's a configuration option
- to disable all telemetry. Note that the board will still
- enable the radio link in idle mode.
- </listitem>
- <listitem>
- Arbitrary frequency selection. The radios in Altus Metrum
- devices can be programmed to a wide range of frequencies, so
- instead of limiting devices to 10 pre-selected 'channels', the
- new firmware allows the user to choose any frequency in the
- 70cm band. Note that the RF matching circuit on the boards is
- tuned for around 435MHz, so frequencies far from that may
- reduce the available range.
- </listitem>
- <listitem>
- Kalman-filter based flight-tracking. The model based sensor
- fusion approach of a Kalman filter means that AltOS now
- computes apogee much more accurately than before, generally
- within a fraction of a second. In addition, this approach
- allows the baro-only TeleMini device to correctly identify
- Mach transitions, avoiding the error-prone selection of a Mach
- delay.
- </listitem>
- </itemizedlist>
- </para>
- <para>
- AltosUI Changes
- <itemizedlist>
- <listitem>
- Wait for altimeter when using packet mode. Instead of quicly
- timing out when trying to initialize a packet mode
- configuration connection, AltosUI now waits indefinitely for
- the remote device to appear, providing a cancel button should
- the user get bored. This is necessary as the TeleMini can only
- be placed in "Idle" mode if AltosUI is polling it.
- </listitem>
- <listitem>
- Add main/apogee voltage graphs to the data plot. This provides
- a visual indication if the igniters fail before being fired.
- </listitem>
- <listitem>
- Scan for altimeter devices by watching the defined telemetry
- frequencies. This avoids the problem of remembering what
- frequency a device was configured to use, which is especially
- important with TeleMini which does not include a USB connection.
- </listitem>
- <listitem>
- Monitor altimeter state in "Idle" mode. This provides much of
- the information presented in the "Pad" dialog from the Monitor
- Flight command, monitoring the igniters, battery and GPS
- status withing requiring the flight computer to be armed and
- ready for flight.
- </listitem>
- <listitem>
- Pre-load map images from home. For those launch sites which
- don't provide free Wi-Fi, this allows you to download the
- necessary satellite images given the location of the launch
- site. A list of known launch sites is maintained at
- altusmetrum.org which AltosUI downloads to populate a menu; if
- you've got a launch site not on that list, please send the
- name of it, latitude and longitude along with a link to the
- web site of the controlling club to the altusmetrum mailing list.
- </listitem>
- <listitem>
- Flight statistics are now displayed in the Graph data
- window. These include max height/speed/accel, average descent
- rates and a few other bits of information. The Graph Data
- window can now be reached from the 'Landed' tab in the Monitor
- Flight window so you can immediately see the results of a
- flight.
- </listitem>
- </itemizedlist>
- </para>
-</article>