Merge branch 'master' of ssh://git.gag.com/scm/git/fw/altos

[fw/altos] / ChangeLog

commit 332b056459b1352e233a8bf5f08498df12d32160
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Sep 4 15:01:32 2009 -0700

    'fix' ao-eeprom to read two blocks at once. Work around kernel bugs.
    
    The kernel appears to leave serial data undelivered at times. Reading
    two blocks at once appears to make it relinquish the queued data.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit df88ae4c5f229efcc0ea5cb0a81fc2bb8f96fea2
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Sep 4 14:23:02 2009 -0700

    Add 'ao-list' utility to show attached AltOS devices
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 0935d6a7e907e20381a42882ae728051f9bece02
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Sep 4 14:21:19 2009 -0700

    Parse the USB serial number as an integer.
    
    AltOS devices use simple integer serial numbers, so parse the USB
    value as such to make matching values more forgiving.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 0c771d999914f9d17c723900f2987acc45fd0fbb
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Sep 4 13:00:02 2009 -0700

    Move usb scanning code to ao-tools library
    
    This will allow the scanning code to be used by the command line tools
    as well as the ao-view GUI.
    
    Now that ao-view depends on the ao-tools library, it has been moved to
    the ao-tools directory as well.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 15341b6e6dcf52df083d6aa37ef881ea6ad48ee5
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Sep 4 12:25:37 2009 -0700

    Set all of the values to reset the radio for telemetry
    
    Was sizeof(rdf_setup) instead of sizeof(telemetry_setup) when
    resetting the radio back to telemetry data mode from rdf mode. With
    the length value removed from the rdf config, these two arrays are no
    longer the same length, and so the last config value was not set
    leaving the radio sending garbage.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit fee46389b70a624ab5b1128a8b4c3083c7747bcb
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Sep 4 11:46:55 2009 -0700

    Make RDF beacon only run on pad and after landing.
    
    It's pretty much impossible to RDF the rocket during flight, and it
    interferes with the telemetry data stream. Leave it enabled on the pad
    so that radios can be tested, and then re-enable it once the rocket
    has landed.
    
    This patch also turns the rdf 'on' time into a parameter so it can be
    changed, and then sets that parameter to 500ms, once every 5 seconds.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 54545640b0db7747137655f84bc67fd290ecb904
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Sep 4 11:45:52 2009 -0700

    Add back the RDF tone generator
    
    Tracking the rocket on the ground may be easier using tones than using
    the digital data stream, so we'll try that and see what we think.
    
    This reverts commit 3a3bfd471a868d546d83cdc431b53c8f5208edb9.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 9fafee109e96435c96639b21211cac0500673a63
Author: Bdale Garbee <bdale@gag.com>
Date:   Wed Sep 2 23:18:15 2009 -0600

    update changelogs for Debian build

commit cb4a73f3b65ba72f645fd37ab8712829c9537bf8
Merge: 9ddd869 e2e449d
Author: Bdale Garbee <bdale@gag.com>
Date:   Wed Sep 2 23:17:37 2009 -0600

    Merge commit 'origin/master'

commit e2e449d5c23356e913f312de1fb2611a9dd5a352
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Sep 2 22:01:52 2009 -0700

    Remove bit-banging debug support from TM board builds
    
    Our current TM boards don't have the wires to do bit-banging to
    another cc1111 board, so it doesn't make sense to fill up their flash
    with useless code (and the 'help' text with useless commands). Leave
    this to the TI board until we have boards that can serve as debug dongles.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit acea083d80e1ecc4287083519ea666964016b257
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Sep 2 22:00:37 2009 -0700

    Make the ao_log_record structures 8 bytes again.
    
    When the GPS signal strength data was added, the structure was
    accidentally extended to 9 bytes, making all log records 9 bytes
    long. While not a serious problem, this left log records spanning
    across eeprom block boundaries, which seems like a bad plan.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 7d39f17684feb49ac8a0017902158f298696e37c
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Sep 2 21:57:54 2009 -0700

    Make eeprom reads and writes across block boundary work
    
    Reading and writing across the block boundary was not stepping the
    eeprom position after the partial i/o operation at the end of the
    first block. This meant that the operation would re-use the end of the
    previous block, either re-reading or re-writing it.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 9ddd8696b4004ccc03238d95a8c2a1d07075e0fb
Author: Bdale Garbee <bdale@gag.com>
Date:   Mon Aug 31 16:48:03 2009 -0600

    update changelogs for Debian build

commit 6926c4ab5d87a8f2eb4fcde2c673fb3a4639e115
Author: Bdale Garbee <bdale@gag.com>
Date:   Mon Aug 31 16:47:44 2009 -0600

    pixmap file should not be executable

commit 1495e2f27acde3743c3764a0c31ee082224d6c64
Author: Bdale Garbee <bdale@gag.com>
Date:   Mon Aug 31 16:42:55 2009 -0600

    update changelogs for Debian build

commit c8c5b7963babe8eb16e2651fba9cd2c8d1cba74e
Author: Bdale Garbee <bdale@gag.com>
Date:   Mon Aug 31 16:42:37 2009 -0600

    deliver an icon for the Debian menu system

commit 591b99c232e780246fc07841c09c8c4e7835facb
Author: Bdale Garbee <bdale@gag.com>
Date:   Mon Aug 31 16:26:00 2009 -0600

    update changelogs for Debian build

commit b34474c1f3083e73b7184d519f54d4c8031836fd
Merge: 8df1697 0d65bff
Author: Bdale Garbee <bdale@gag.com>
Date:   Mon Aug 31 16:25:32 2009 -0600

    Merge branch 'master' of ssh://git.gag.com/scm/git/fw/altos

commit 6358041f846ba9a20fa650c367d907dc4336e54c
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Aug 22 13:38:56 2009 -0700

    Enable GPS degraded mode, set 10 sec degraded timeout.
    
    No reason not to let the GPS report solutions whenever it likes, let's
    see how this works.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 0d65bff443c17d4d98c18b620ec075ab66b30efd
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Aug 21 10:47:46 2009 -0700

    Turn off GPS tracking data when not present in data stream
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 8df169791835510d96c11a3b0aa3cc5b79fa7fde
Author: Bdale Garbee <bdale@gag.com>
Date:   Wed Aug 19 02:21:23 2009 -0600

    update changelogs for Debian build

commit 42ab6d52540d0326ef89e9d57954b08248558468
Author: Bdale Garbee <bdale@gag.com>
Date:   Wed Aug 19 02:21:06 2009 -0600

    fix location for delivery of sources.list fragment

commit 977f5dc0bc7c666dcc1f21db77416efca0d696aa
Author: Bdale Garbee <bdale@gag.com>
Date:   Wed Aug 19 02:11:11 2009 -0600

    update changelogs for Debian build

commit 8d4d6655f1b4c2fbc522fd255bfb75406e5ddaef
Author: Bdale Garbee <bdale@gag.com>
Date:   Wed Aug 19 02:11:00 2009 -0600

    oops, aoview is now ao-view!

commit b9a97aea65f871fd287bc0bb566d8664766f4afd
Author: Bdale Garbee <bdale@gag.com>
Date:   Wed Aug 19 02:07:16 2009 -0600

    update changelogs for Debian build

commit 21e3dd0affac89919e5d0e29c6e9eb1eacb51801
Author: Bdale Garbee <bdale@gag.com>
Date:   Wed Aug 19 02:06:49 2009 -0600

    enable support for Debian menus

commit 0087c1776e0253fc2bd3b86f15bf9d1b32bdc45a
Author: Bdale Garbee <bdale@gag.com>
Date:   Wed Aug 19 00:52:57 2009 -0600

    update changelogs for Debian build

commit 4486d9156e19e4280b42bcd422d81d04f2d04a92
Merge: dd09f0b 33edd62
Author: Bdale Garbee <bdale@gag.com>
Date:   Wed Aug 19 00:49:24 2009 -0600

    Merge branch 'master' of ssh://git.gag.com/scm/git/fw/altos

commit 33edd62992a32b0ec8ca66d879fa300871db5937
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Aug 18 23:38:16 2009 -0700

    Update ao-view to add GPS satellite tracking data
    
    This adds another column to the display to hold per-satellite GPS
    tracking data and a count of the visible and locked sats.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 29687cbd462a332d9a36ed87500c5b737dcae3f4
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Aug 18 22:35:15 2009 -0700

    Handle GPS satellite tracking data
    
    SiRF message #4 includes signal strength and GPS engine state for each
    of the satellites being tracked. This data is now parsed and sent to
    eeprom and the radio.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit dd09f0bc2b950c00f3b489878cd69ad8a003f46c
Author: Bdale Garbee <bdale@gag.com>
Date:   Tue Aug 18 21:57:01 2009 -0600

    update changelogs for Debian build

commit cd5ce661e2a8f9694933358ccb5b916fbed089c2
Author: Bdale Garbee <bdale@gag.com>
Date:   Tue Aug 18 21:49:39 2009 -0600

    add support for building Debian package

commit d996aa9b32fb0eb385bd3d158256c29788a42fe3
Merge: b3b2d3c 7d4ceb7
Author: Bdale Garbee <bdale@gag.com>
Date:   Tue Aug 18 18:56:09 2009 -0600

    Merge branch 'master' of ssh://git.gag.com/scm/git/fw/altos

commit 7d4ceb75a454e6c9b3fe0bd934fadcb5104dea36
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Aug 18 17:55:22 2009 -0700

    Add ao-ejection.1 man page
    
    Document the input requirements and output format
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit b3b2d3c475a135084b5628c730fc6fca1ba0817b
Merge: 4685fc5 da12b89
Author: Bdale Garbee <bdale@gag.com>
Date:   Tue Aug 18 18:36:03 2009 -0600

    Merge branch 'master' of ssh://git.gag.com/scm/git/fw/altos

commit da12b89fb056a68e65ba363fef91d266727cb685
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Aug 18 17:30:43 2009 -0700

    Create ChangeLog from git log

commit 7d69e2b3715faed10ce21ad562fc4d25dfc5f9c1
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Aug 18 17:29:29 2009 -0700

    Fix ao-bitbang examples to not have . in the first column

commit 4685fc541466afbeefc151bcb64cd054739c048b
Merge: 1c2a0b6 c29275b
Author: Bdale Garbee <bdale@gag.com>
Date:   Tue Aug 18 18:09:38 2009 -0600

    Merge branch 'master' of ssh://git.gag.com/scm/git/fw/altos
    
    Conflicts:
        ao-tools/ao-bitbang/Makefile.am
        ao-tools/ao-eeprom/Makefile.am
        ao-tools/ao-load/Makefile.am
        ao-tools/ao-load/ao-load.c
        ao-tools/ao-rawload/Makefile.am

commit c29275b72438637d46d7a50742882d2736eb176a
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Aug 18 15:21:57 2009 -0700

    Add manual pages for remaining commands.
    
    Manuals written for ao-bitbang, ao-eeprom, ao-load, ao-rawload and
    ao-view.
    
    Manual for ao-dbg updated to reflect program name change.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 9b03d620722dc54630539afba40720c30de69b2d
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Aug 18 12:19:31 2009 -0700

    Use --tty/-T on command line to specify target device
    
    Also, use the ALTOS_TTY environment variable in all tools. Note that
    the magic value of "BITBANG" switches the library to connecting
    through a CP2103 instead.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 7c790fe859dff062692964338091ffbbcdf63257
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Aug 18 12:40:24 2009 -0700

    Rename tools to ao-<foo>
    
    Use a consistent prefix to make it easier to remember which programs
    belong to this package
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 1c2a0b6653623b689d68d7349a6b2dce3e20a4a6
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Aug 18 13:36:54 2009 -0700

    re-add debugger sources

commit 9a9cce5510b87252f863239ac807b9fb4395b288
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Aug 18 12:19:31 2009 -0700

    Start working on using getopt for the tty name

commit 9789ca5e8caa9a013e804f307b9da380e147bd75
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Aug 18 12:40:24 2009 -0700

    Rename tools to ao-<foo>
    
    Use a consistent prefix to make it easier to remember which programs
    belong to this package
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit a5782398d968e7cb11f7203afada7c216f233b3b
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Aug 18 11:34:28 2009 -0700

    Remove unused cctools code paths for old libusb and cp2103 ioctls.
    
    Communication with the CP2103 board has gone through three revisions,
    first using ioctls supported by the CP2103 kernel driver, then using
    the old synchronous usb library and now using the newer libusb
    asynchronous interface. There's no reason to keep shipping the old
    stale code now that the new stuff works reliably.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 7cba411de0780c65e3490ab67186a514f0ea42ec
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Aug 17 20:47:31 2009 -0700

    test for sdcc, nickle and readline
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit f48dcffae761700355a17b59345d55a60703f0c4
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Aug 9 20:43:10 2009 -0700

    Sync USB data after each memory write command
    
    This makes sure we flush the USB link often enough for the other end to keep
    up.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit cd5456f18e4b39ad76d5549df91a0e0cfb18a2e9
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Aug 9 16:08:07 2009 -0700

    Handle partial ALSA PCM writes
    
    The ALSA spec says that snd_pcm_writei will not return a partial write, but
    at least on the OLPC, that's not true. Deal with this.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 3056cb8eef5aee0dcd342488386355d8b8f574c8
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Aug 9 15:55:19 2009 -0700

    Check more alsa return statuses

commit 8ddf3345afd8cbf638e81993633f7861d8dbca63
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Jul 18 01:47:34 2009 -0700

    Don't report distance to rocket without valid GPS
    
    When there's no valid GPS data, don't try to report the distance and bearing
    to the rocket after landing.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit fbcb7b20fa701a6e534d38e307839466545668e3
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Jul 18 01:05:33 2009 -0700

    Add B command to set serial baud rate
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 91b023e7e4eeed838e0320d2ddac0f6aac39e565
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Jul 18 01:05:13 2009 -0700

    Get rid of spaces after minus sign in climb value

commit 28be20cf914fb34dc3c776519708d0f02091764e
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Jul 18 01:04:39 2009 -0700

    Switch to 57600 baud for GPS data

commit d3f76ce58b9c0ed2e5a9fe3bbc7fb9cb38247714
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Jul 18 01:04:17 2009 -0700

    Drain serial port before changing speed
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit d7c2d358ed8a1afc9f0ba2bd830b10f6b56dc7b1
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Jul 18 00:44:42 2009 -0700

    Display last known GPS coord while unlocked
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 5195fcfe239e430e1f9f11774c9a245c7b29dae9
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Jul 18 00:44:01 2009 -0700

    use g_source_destroy instead of free on serial object

commit 1e5e98bd8f5ea0bc15592de454e3629383462371
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Jul 18 00:43:22 2009 -0700

    Trim aoview_serial_set_callback args down to just port and callback

commit 08f37056deec25d77062bc411a04033401b033a5
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 22:11:03 2009 -0700

    Reset GPS at boot time

commit 1150aa850f5a025b849556e32c4dddb27937d9af
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 22:10:43 2009 -0700

    Fix up serial debug output

commit 2a7956a64935246475f92d44c08369e0230b676a
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 21:34:13 2009 -0700

    Allow the GPS port to run at 4800 baud if desired

commit 8d650769c319261c97f5e68eff9138207b95c0f8
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 21:33:53 2009 -0700

    Initialize the GPS serial protocol state
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit ab40d224b39ba6d29c4056e2d2c365e1eb3d3793
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 21:33:18 2009 -0700

    Use uint8_t for comparisons to avoid int conversions
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit d6749bf24792bb41ca700cf4b8e5e1ac1a63cbf0
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 21:30:53 2009 -0700

    Add AO_GPS_RUNNING state.
    
    This tracks whether the GPS receiver has ever sent a valid report to the
    flight computer, allowing the user to tell whether the GPS receiver is
    working at all.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit a1da7e871aee75308bc05ce1b7a0dc402e4c9509
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 21:25:35 2009 -0700

    Add M command to monitor serial bytes

commit ddfa2308c0be4c002f982ae9da6032ee7854117d
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 21:24:45 2009 -0700

    Support the not-connected GPS state

commit 34f148500df427c148188c0ada20bf914a7c74ba
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 19:23:10 2009 -0700

    Use 57600 baud for GPS. Clean up gps init.
    
    Assume GPS is either in 4800 NMEA or 57600 SiRF mode, send just the sequence
    to get from 4800 NMEA to 5760 SiRF.
    
    Also, eliminate threads from the gps test program.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 2deca0c52cd6cfb4baceb59c8a5458344bada338
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 17:09:20 2009 -0700

    Try harder to get the GPS receiver serial link sync'd up.
    
    We cannot assume that the GPS receiver is in any particular state when it
    boots, so we try to send the serial configuration at several rates and hope
    that it eventually sees something that it likes.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 31d5670a9144b943ce9c8cb00deb5fb659af0b1c
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 17:06:18 2009 -0700

    Rolling average for pad location. Say 'GPS ready'.
    
    Use a rolling average for the pad location, instead of just averaging all
    positions. This filters out old (presumably less accurate) values eventually.
    
    When enough GPS samples have been acquired, say 'GPS ready'.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit bfe1e76c82738baaf65abbc58c3244a07ea8fefe
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 16:22:51 2009 -0700

    Split GPS data into a separate column
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 5f0179652e8bb85add9067e5253e981c60f2c51e
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 16:03:35 2009 -0700

    Fix up SiRF parsing and test code so that it actually works
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 0b35447d05a0c7eaf4fefcbcf0065fe3320bba82
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Jul 17 13:58:14 2009 -0700

    Add host-side gps protocol testing program

commit fef7334bddb9fccfbd6deab7d5d466ab3e76323a
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Jul 11 00:56:13 2009 -0700

    Hook aoview directly to alsa
    
    This skips the flite internal audio stuff which opened and closed the audio
    device for each phrase. This caused the first part of some phrases to be
    missed when using an external audio device.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 80cadf44f5f1accd6ddfca25c2af8d4d424f26d9
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Jul 9 20:55:10 2009 -0700

    Show speed. Format numbers. Timeout and report final status.
    
    The speed value is now shown in the top label bar. Ascent shows
    accelerometer-derived data, otherwise it's baro derived.
    
    All of the numbers displayed are now given sensible printf formats so they
    don't contain way too many digits.
    
    Instead of doing periodic reporting based on flight tick count, data is
    reported every 10 seconds based on wall time. After landing, or when no data
    have been received for a while, final flight information is spoken.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 19630ef084866f4230e68ccf11284b30c68128b1
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Jul 5 08:35:28 2009 -0700

    Dont smash aoview_monitor_parse input buffer

commit e506ed4b6efb86eab50204658fcd433b987e3831
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Jun 30 15:25:52 2009 -0700

    Integrate flite into aoview directly. Fix great circle computation.
    
    Use a separate thread for flite rather than a separate program.
    Save voice state to gconf.
    Add filters for replay file selection
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 5b988e0146075d57434f8484e1ec9fcf3e183df2
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Jun 30 15:24:53 2009 -0700

    Make window taller

commit 696233b088645bba1aaa6aa6c5358c3ecfa5cd3f
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Jun 30 15:24:31 2009 -0700

    Use 16kHz voice

commit 2e06772c8b6fd74f86e640ed97f0d5bc8c095c2f
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Jun 30 11:58:30 2009 -0700

    Add telem replay and larger labels
    
    Replays telemetry files in real time
    Shows height/state/rssi in big values at the top.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 566dde161385263700eaae51095eecfa9b5972ee
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Jun 29 23:06:47 2009 -0700

    Update aoview/.gitignore
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 4ca2d910f3be689fd3c78a4f1be0555d6b1a30c1
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Jun 29 23:05:27 2009 -0700

    Use flite to announce flight state
    
    This uses the flite voice synthesis library from festival to announce
    altitude and speed information during the rocket flight.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 527d7c803ed9597b210634018cb2eb9d048d9846
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Jun 29 23:03:58 2009 -0700

    Add GPS speed and error data to telemetry and aoview
    
    Having switched to the SiRF binary GPS format, the velocity and error data
    can now be displayed.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit ee4919dd771b00e2a2dd1083c9528efa7baab50f
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Jun 29 13:54:00 2009 -0700

    Convert GPS to SiRF binary protocol.
    
    This switches the GPS unit from NMEA to SiRF protocol at startup and then
    parses the binary data. The binary data uses a different encoding of lat/lon
    than the NMEA strings, and so the telemetry and eeprom data formats change
    with this switch.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 49bf37767d2453869f2ca2c0832d1124322c66e0
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Jun 17 23:22:25 2009 -0700

    Add ejection computation utility
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit e59520e343c2573b1b92c0b3c4aaa93e51bc55d3
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Jun 17 13:55:23 2009 -0700

    Fix clock initialization to not try to use 32kHz xtal on P2_3/P2_4
    
    None of our boards have a 32kHz xtal oscillator, instead we use those pins
    (on Telemetrum) for the deployment firing circuits. The old clock
    initialization code was switching from the 32kHz RC oscillator to the 32kHz
    crystal and overriding our use of those pins.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 1c3cc12c08ddefbd6456a55c54ef87dd94d4ae9a
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Jun 14 17:25:34 2009 -0700

    Some kernels reference USB ttys as tty/tty* instead of tty:tty*
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 0f2cbd41332b1b63865c5f1a4e749419b469853a
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Jun 14 16:45:19 2009 -0700

    Rename state apogee -> coast

commit 5834a12c1d3d71105c9e3d1ceaf9f3ffac9ff1eb
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Jun 14 16:39:28 2009 -0700

    rename states. launchpad -> pad, coast -> fast

commit 8c40f19acd09fe93d492c9355da8a1198c34b1c3
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Jun 14 16:36:29 2009 -0700

    Disable monitor mode when communicating via usb

commit 7adea9c59c73acd52743446c74fb675e0a1d6d05
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Jun 4 14:38:45 2009 -0700

    Format GPS seconds as %02d.%04d to avoid spaces in the value
    
    The aoview GPS parsing code doesn't deal well with spaces in the middle of
    the value, so pad the seconds field with a zero as needed.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit a0e6bfee635b64092262936c858542318f6fc6dc
Author: Bdale Garbee <bdale@gag.com>
Date:   Thu Jun 4 13:11:48 2009 -0600

    newer INSTALL file pulled in by autogen.sh

commit cf1e258d52b878df10b51a047709b10ecd51a68e
Author: Bdale Garbee <bdale@gag.com>
Date:   Thu Jun 4 13:09:29 2009 -0600

    add a distclean target to src/Makefile

commit 176052b7c14fcad067835ecb550778faf67cf4da
Author: Bdale Garbee <bdale@gag.com>
Date:   Thu Jun 4 13:07:10 2009 -0600

    add lib to the front of the subdir list

commit 208bc15714c7b4020c017eef19011c4eb9ab51e2
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Jun 4 11:20:10 2009 -0700

    Move build and debug tools to 'cctools' directory.
    
    These tools were merged in from the ccdbg package.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 17d2432a8b9c15963cd3b821f025ad33972ef477
Merge: 210dbaa 8a9a3f0
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Jun 4 11:13:15 2009 -0700

    Merge ccdbg and altos sources into one giant repository
    
    Keeping these separate isn't making things any easier.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 210dbaa23cdacf3a6f2d6e23493e96ee2ac9bca7
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Jun 4 10:41:34 2009 -0700

    Use autotools, move altos to src subdir
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 8cce307bb3156584ba17ae5a787f645dfee5fb94
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Jun 4 10:25:30 2009 -0700

    Make menu seperator insensitive

commit 778cae8fc5a4b30e5045e4703316fc61ae18562a
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Jun 3 17:07:34 2009 -0700

    aoview: Add eeprom data fetching
    
    Fetches the last flight data from a TM device connected via USB and writes
    it to the flight log directory.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit bf140966e9649e75b884c8aa5f25ffbf9eed10ea
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Jun 3 10:57:46 2009 -0700

    Stop log dumping at flight end. Print 'end' at end of log.
    
    No reason to continue dumping data past the end of the flight now that the
    logging stuff has been demonstrated to work reliably. Also, to make
    automated log dumping easier, this prints out 'end' after the log data so
    that aoview knows when to stop reading.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 35ac66969abe24ca23776618306a59fc17770e06
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 31 09:22:01 2009 -0700

    Start adding bi-directional packet link

commit 3a3bfd471a868d546d83cdc431b53c8f5208edb9
Author: Keith Packard <keithp@keithp.com>
Date:   Thu May 28 23:17:33 2009 -0700

    Eliminate RDF tone generation.
    
    Now that we have a viable telemetry-signal based RDF device via TeleDongle,
    there's no reason to continue to waste power and bandwidth with a NFM tone.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 4d83eef0fe1d24a845ab29a535dfc56e13e7ee20
Author: Keith Packard <keithp@keithp.com>
Date:   Thu May 28 23:17:25 2009 -0700

    Change .gitignore to match new aoload procedure

commit dcfcf3bec6788460b6fe8c239c80bad4526bd15b
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 27 22:01:37 2009 -0700

    Leave serial number writing to aoload
    
    Instead of building per-serial hex files, leave that
    process to the new aoload program
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 8a9a3f02b951382573ff74dd6ce5a1c0f335fa86
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 27 21:53:15 2009 -0700

    Add aoload to load serial-numbered altos binaries.
    
    aoload is a custom version of ccload which edits the data before sending it
    to the target machine, writing the target serial number into the data.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 5a7a63c34b778e40a61ddabd16ec1af9a2be50c3
Author: Keith Packard <keithp@keithp.com>
Date:   Sat May 23 21:20:12 2009 -0700

    Fix aoview telemetry GPS parsing code to use correct columns
    
    This code was trying to pull the GPS data from the wrong columns, causing
    aoview to fail to display GPS information.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 26988c3e7acb2fa832810475e43e08fd2867459c
Author: Keith Packard <keithp@keithp.com>
Date:   Sat May 23 21:18:57 2009 -0700

    Parse both telemetry or log data ao_flight_test
    
    Change the way data is fed from files to the flight test rig to handle
    either kind of input file.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit d6f5a0689023546464a71561f53fa2c943077c88
Author: Keith Packard <keithp@keithp.com>
Date:   Sat May 23 21:16:22 2009 -0700

    Avoid 16-bit overflow in velocity computation.
    
    Adding two 16 bit integers together can wrap around to negative numbers,
    this resulted in velocity values which never decreased, making the switch
    from coast to apogee state not occur.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit aa6d87aeb616dd62f0debaded297232022b4f8bd
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 20 09:44:55 2009 -0700

    Make file handling more general so it can be reused.
    
    The log file handling stuff will be useful for saving eeprom data, so pull
    it out of the real-time log handling code and make a general interface.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit b730c8bcbce649cdddba935e1112aaae538bc526
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 23:54:44 2009 -0700

    Ignore aoview_glade.h

commit 91b07410122d0eaaf292cdb31c200925d45eaf2c
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 23:36:21 2009 -0700

    Transmit computed ground pressure and acceleration values
    
    These are the last two values relevant to figuring out the state of the
    flight computer, and as they are computed by averaging 10 seconds of 100Hz
    sample data, they're a lot more accurate than anything the receiver could do
    on its own.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 71d1689759829f1bc8550f1a4d8c9f2dc90b2ab4
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 23:18:09 2009 -0700

    Provide install target

commit f301b95e87c8ec1e3b58d595a05d486bede5e0c2
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 23:13:20 2009 -0700

    Embed glade file in executable
    
    This eliminates install issues nicely.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 26361686d6fc63dc22d22285f0543c5c2c756fb4
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 23:05:23 2009 -0700

    Add About dialog to aoview.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 0f3233c49f43cd4e372e613303919ce4d50255b2
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 22:44:19 2009 -0700

    USB device names can contain '.' too
    
    Depending on the hierarchy of devices, names can contain '.', so allow those
    too.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 33221277690e6ee30387c506c3f2b8237ed48efd
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 22:43:34 2009 -0700

    scandir returns -1 on error
    
    In which case, the namelist is invalid, so don't look at it, and don't free
    it.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 7cb9fb675f56bf30ab6bf0bcdc5cb679709ffe3e
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 22:29:54 2009 -0700

    Send computed accel/vel/pres values over the radio
    
    These computed values reflect what the flight computer is actually refering
    to for state changes, and will be useful in debugging the flight software as
    well as provide a filtered view of the data.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 2c780d67b8a22d75a2da4b2af21fd35f0c6f5236
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 22:29:06 2009 -0700

    Handle disappearing serial devices
    
    Put up a dialog when the serial open fails, and shut down monitoring when
    the serial device disappears while running.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 69616104813fc5ba89fb3128d04fb9328961c59c
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 22:24:53 2009 -0700

    While on the pad, zero out velocity every second
    
    We integrate acceleration to get velocity, but that means sitting on the pad
    for a long time can add substantial error to the velocity value. Each
    second, take the velocity value from a full second ago and subtract that out
    of the current velocity. Once we detect boost, this will stop, which means
    that as long as we detect boost within a second, we won't have subtracted
    out any "real" velocity.
    
    This keeps the pad velocity hovering around zero, which is pretty useful.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 1234694eb903b204488ddc7cb30bcfe34bf1e677
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 01:29:06 2009 -0700

    Clear table, reset log on disconnect

commit 4316b6af86b37522038e642235c163fcaad52e96
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 01:28:16 2009 -0700

    Add pad lat/lon, max accel, max height
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 4348281bd788a13ea700413537f12da3c00356e4
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 00:46:09 2009 -0700

    Clean up GPS display
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit ff68e38770351ddac3285ce275cd85adab01fd3d
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 00:45:38 2009 -0700

    Make aoview window taller
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit be3f4fed7b863c8cdaabe32b61b65a8b3cd11355
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 17 00:13:45 2009 -0700

    Add lots more aoview UI bits
    
    Logs data to files, displays current state in window.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 93d7ce8e054515ed7b166eb042ae7f47e564d21d
Author: Keith Packard <keithp@keithp.com>
Date:   Sat May 16 20:45:26 2009 -0700

    When logging starts up, right the whole ring to the log.
    
    This preserves the data pre boost-detect for later analysis.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit fec4212a59a7b3321536b25707dcabc43c797c33
Author: Keith Packard <keithp@keithp.com>
Date:   Sat May 16 20:04:31 2009 -0700

    Abandon use of accelerometer for apogee detect.
    
    Integrating the accelerometer data to compute velocity worked for one rocket
    flight, but additional testing shows that it doesn't work in other
    airframes. Until we figure out how this should work, we'll rely on the
    altimeter to detect apogee.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 09771c644de54ae354e8f98af7ba74289b3c0fcc
Author: Keith Packard <keithp@keithp.com>
Date:   Sat May 16 02:25:04 2009 -0700

    Add preliminary aoview code
    
    AoView connects with TeleDongle to present telemetry information in a
    reasonable form. Right now, it just displays information to stdout, but it
    does have fancy dialogs for finding the USB devices.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 37250b00f6286aee4b3b28604f5d463db3079a89
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 13 20:41:54 2009 -0700

    Discard usb output before connection. Handle USB reset.
    
    Discarding output before USB is plugged in allows threads that send output
    and do other things to work without a USB connection. Unfortuantely, there
    doesn't appear to be any way to detect when the USB link is disconnected,
    which means that once USB is enabled, future writes will continue to block.
    
    USB reset causes the USB interrupts to all be reconfigured back to power-on
    state.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 9b974217958b1017e62d6c4f4568f547ccc30c58
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 13 20:40:42 2009 -0700

    Enable radio monitor by default in teleterra, teledongle and tidongle
    
    These ground loads want to monitor the radio constantly, and not require use
    of the 'm' command before listening.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 25fc03a333b2cfad0a93ebc385fbcf74b63c229e
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 13 20:39:28 2009 -0700

    Remove monitor/rssi functions from telemetrum load
    
    Telemetrum is now a flight-only load, use teleterra or teledongle for ground
    boards.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 05493b98eb1ae4d30cb0b600849d70b03fa33594
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 13 20:38:11 2009 -0700

    Split out ao_state_names to separate file
    
    Allows state names to be used in programs without monitoring enabled.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit d085d43701e3cdd2119e947a9ae45baa78c80318
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 13 14:29:30 2009 -0700

    Indicate RSSI with a blinking LED
    
    Blink the red LED at a rate proportional to the RSSI value.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 055331d5f7d5adc40c348c3efd331a562dcda82a
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 13 11:19:13 2009 -0700

    Make ao_flight_test show AGL altitude and positive acceleration under boost
    
    This makes the output more readable
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit d91208fbf5fc7797b93087ef8619454c4bed0130
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 13 11:18:24 2009 -0700

    Make ao_flight_test able to read raw logging data
    
    Protect ao_flight_test reading functions so that a simple
    'script' output can be fed to the program and have it work correctly.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit d3dbd8949e1102220ad5fd0863f493c819b96e46
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 13 11:16:53 2009 -0700

    Print only RSSI when packet CRC is invalid
    
    Packets with invalid CRC usually contain bogus data, so don't print that,
    just print out the RSSI which may contain useful data.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 8168820b667cc1deffab64dd81cb4e6e2e6eabe4
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 13 11:00:43 2009 -0700

    Accelerometer-based velocity values are invalid after apogee
    
    Because the orientation of the flight computer relative to the ground is
    unknown after apogee, the accelerometer data cannot be integrated to compute
    velocity. Main deploy is now based purely on barometric altitude and landing
    detection no longer checks for a low velocity value.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 24fdda44ff8604e40510b196ead17564d8f8cd3d
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 13 10:59:04 2009 -0700

    Add velocity check for boost detect via accelerometer
    
    Bumping the rocket can cause a brief period of high acceleration, which may
    cause a mistaken boost detection. Require both a high acceleration and
    reasonable velocity to trigger boost phase.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 7a1aa3fdbc0d1fae5e7ee027bf8904598c6ebe41
Author: Keith Packard <keithp@keithp.com>
Date:   Wed May 13 10:58:30 2009 -0700

    Typo in callsign

commit 497c89a7d08920630894b2605c3b6a0bdc4c229b
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 10 23:11:06 2009 -0700

    Use recorded accelerometer baseline data in ao_flight_test
    
    With the flight computer recording a long-term average value for the
    accelerometer in the flight record, use that to prime the flight test code
    when running a log file through the simulator.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit ba3c53636e485450f48093d0a88a6629775f7c3a
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 10 23:01:16 2009 -0700

    Don't re-initialize the landing range data at each apogee detect sample
    
    The landing range values are used only after apogee detect, so we need only
    initialize them on the transition from apogee to drogue.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit b623b1098bc7a10d471730259438fb82804221d0
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 10 23:00:06 2009 -0700

    Initialize ao_min_vel with |ao_flight_vel|
    
    As ao_min_vel is stored as an absolute value, it's important to preserve
    that invariant, even though we don't expect ao_flight_vel to be negative at
    coast.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit e9584e846b9bd7926d61451d32ba5d7a30416f7b
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 10 22:58:31 2009 -0700

    Decrease telemetry rate on the pad to 1/sec instead of 20/sec
    
    Transmitting telemetry through the radio consumes a significant amount of
    battery; reducing the rate to 1/sec will reduce power usage while waiting
    for launch.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 97cecb517cd7bf75e1219c76a93bfe6964c07052
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 10 22:57:19 2009 -0700

    Increase the initial accel/baro average to 1000 samples
    
    To get an accurate baseline of the launchpad state, take a longer average of
    the two sensors as the unit boots up.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 98806b1ff3f41484663d61ff430e9e2764c7b5e6
Author: Keith Packard <keithp@keithp.com>
Date:   Sun May 10 22:54:14 2009 -0700

    Record average accelerometer value in flight start log record
    
    The average accelerometer value cannot be extracted from the log as the
    record starts after that is computed. As that drives much of the
    accelerometer-based state transition logic, it is an important value to
    have, so we log it as part of the flight start record now.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit a12edbfe21fe27a9efbf87bacda9ab4806256e2b
Author: Keith Packard <keithp@keithp.com>
Date:   Sat May 9 10:24:10 2009 -0700

    Add version command to show product information

commit e80b87f5e3ccf152d67a2e87bdefda161c455599
Author: Keith Packard <keithp@keithp.com>
Date:   Sat May 9 10:23:49 2009 -0700

    Pad callsign with nuls

commit beae3360828da21eb1a3c4f88e930f242d4e36b7
Author: Keith Packard <keithp@keithp.com>
Date:   Fri May 1 08:14:57 2009 -0700

    USB spec limits bulk endpoints to 64 byte payload max.
    
    For full-speed devices, bulk endpoints may use 8, 16, 32 or 64 bytes, but no
    more.

commit de7814c738488c2c16c6216c93fa78128895e5d5
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 29 17:46:56 2009 -0700

    Use 'char' instead of 'uint8_t' for character data
    
    String and character constants are of char type, so using uint8_t causes
    promotion to 16-bit types when comparing the two.

commit 4ae74fffb939d67424efa3e7f433637f1f920ebc
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 29 17:46:36 2009 -0700

    Eliminate incorrect cast in printf string argument
    
    char * is a pointer to a string in the default address space, not a generic pointer
    to a string. As such, the compiler (at least 2.9.0) mis-compiles this if the
    cast is included.

commit 39f2a3c6bd501d12a92bfd38434ce67bb5beb70d
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 29 17:44:41 2009 -0700

    Correct radio frequency shown in config display.
    
    Radio frequency base is 434.550, not 435.550

commit 75ca1751b7cac2f8074d0713ee96d6ab45b54f19
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 29 17:42:26 2009 -0700

    Reset landing interval tests at apogee
    
    This moves all of the interval management into the landing test code and
    out of the main loop. The interval is reset at apogee to make sure the
    sensors produce a stable reading for at least 20 seconds

commit 7a1b77c2d7253a681389f32b70e2460aac188807
Author: Bdale Garbee <bdale@gag.com>
Date:   Sun Apr 26 17:53:13 2009 -0600

    clean up host programs, too

commit 5df80c346d65a9d56a8699b056dc44924acb31fe
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 26 16:04:07 2009 -0700

    Was missing v_batt in adc dump command

commit c3fec2c4c65db71e88ef0c05c69463438a7cfc6c
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 26 15:38:28 2009 -0700

    Add manual ignition and igniter test commands

commit 819f1de8dd6010fae050bcef930943c7923929f9
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 26 15:38:03 2009 -0700

    Clean up commands a bit

commit 178abb5c8439509926a5507911d7148b84f051b8
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 26 15:08:58 2009 -0700

    Clear more files on make clean

commit 70a69f3acdca27b80cdb2069de59bbc6dba83dbd
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 26 15:05:29 2009 -0700

    Label binaries with product and serial info

commit 5ed3b1cb52b573db1fee9655a29a0e6dd72f53fe
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 26 01:37:02 2009 -0700

    Make sure full log is written and flushed on landing.
    
    The final state change to landing is recorded in the logging thread, so have
    that turn off logging once it has recorded that state. Then make it go to
    sleep.

commit 2e737ad00cad5d893b252d8aa9dbff3d9b800731
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 26 01:36:53 2009 -0700

    Clean up monitor output a bit

commit 38a0b61b0a0b3c00f064c8d562950a17a6ddff4a
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 26 00:11:32 2009 -0700

    Add configuration support
    
    Current config variables:
    Main deploy altitude above launch (in meters)
    Acceleration zero g calibration (manual or automatic)
    Radio channel (freq = 435.550MHz + channel * 100kHz)
    Callsign (max 8 characters)
    
    Supporting this involved shuffling code around so that the
    non-telemetrum builds could include only the stuff they needed.

commit c65f1a1acd2ca00758833cec5d3f8056d303d3e2
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Apr 25 14:44:33 2009 -0700

    Allow for slower ADC operation. Add power saving code.
    
    This tries to make the flight computer use less power by disabling USB in
    flight mode, lowering the telemetry rate after ascent. It also disables the
    RDF beacon during ascent and re-enables it once descent has started.

commit 8e7b48b5f090be81980ab00fbce814ae1cc253e4
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Apr 25 14:44:04 2009 -0700

    Allow ADC to be disabled

commit 7bc3d9962872850e7b420221cf689db16b4305cc
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Apr 25 14:43:23 2009 -0700

    Place CPU in P0 state while idle

commit e45fce7f82d704d677f84c69b0e07588d109d780
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Apr 25 14:42:20 2009 -0700

    Add RDF beacon and callsign to telemetry

commit 61510f98404bca6861b2da98f6cd9ba9deb76968
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Apr 25 14:40:51 2009 -0700

    Add radio code to emit a 1kHz tone

commit 0f07803d84b5ac89500ee33a6818c50583e3ff7f
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Apr 25 13:18:37 2009 -0700

    Allow the USB system to be disabled/enabled at run-time

commit 45976af820fc41099928df71ea8304c56eb9fc7c
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Apr 25 13:16:27 2009 -0700

    Make LED usage depend on target device

commit 4a050704ad2c497e9f1b0988334228b0bbc4c170
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Apr 25 13:13:24 2009 -0700

    Make some functions reentrant to save DSEG space

commit 6b3d25a6d6d7847765eb03b836913dd5ecef2993
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 24 19:17:37 2009 -0700

    Add monitor task to flight software
    
    Allows the use of telemetrum in teledongle mode.

commit ad0d2d88a91cbd02c56ea5ff6dab23e16aec6510
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 24 19:17:19 2009 -0700

    Report difference from ground to max altitude at landing

commit f94ab879ff6f97708827c74facd11003a2d8b590
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 24 19:16:29 2009 -0700

    Display data with units while running simulation

commit 6fb26340b150e831a8a9e25e3b68074c29e48dbe
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 24 19:13:31 2009 -0700

    Enabling apogee detect via speed: < 200m/s && < max_speed - 50m/s
    
    This change ensures that we actually got going fairly fast, and then slowed
    down a bunch before enabling apogee detect. Otherwise, we'll detect apogee
    right off the pad as we're not going very fast at that point...
    
    This also adds the 'f' command to show the current flight status on the USB
    port.

commit 20b9f304ecbddd73a0ee2461b4c5e80f08157f98
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 24 19:12:28 2009 -0700

    configure igniter ports, set values to measured ones

commit 6bf1d91ce0b723abe2bcec89668c13135ec044cf
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 24 19:11:40 2009 -0700

    Move ao_led_init to end of file to be consistent with other files

commit b4de7d550ec9a09ccf5f6a72debc6646706e3516
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 24 19:10:20 2009 -0700

    Define ao_state_names in ao.h so other people can share

commit 8e62747b3692d0ac75b08eaf5c3e4b5d766be6ad
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 24 19:09:31 2009 -0700

    Bump NUM_CMDS to 10

commit 2f781beb73ef24ab5fbe2688a83d07ad26c15972
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 24 19:09:09 2009 -0700

    Move beep_init to end of file to be consistent with other files

commit b99315cee4ab796376458a2442cf36806fa4aed3
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 24 10:19:31 2009 -0700

    Update flight algorithm based on data collected from SN-1 Flight 1
    
    This now correctly sequences through the flight data collected from the
    first TeleMetrum test flight.
    
    This also completes up the flight algorithm test harness (ao_flight_test),
    which runs the flight algorithm on the Linux host from a captured data log.

commit b32f2f0090ff967edac07ae4d7a9895ed0b96d31
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Apr 23 22:17:44 2009 -0700

    Add igniters and update flight control algorithm

commit f155333ae18a25068644792e8940269d9fb28033
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 24 00:15:09 2009 -0700

    Avoid ram from 0xfda2 through feff, its funky

commit f9c1c545c9dc11c3190a6cf7504883131fffce2f
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Apr 23 22:18:33 2009 -0700

    remove ao_flight_test until its ready

commit 86e73c009f78dc4664883353124fc891fbb01dce
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Apr 23 20:50:07 2009 -0700

    Add teledongle module

commit 204daac71ad56926730f5d6860bd70c645302e19
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Apr 23 14:26:01 2009 -0700

    Set telemetry rate to 100ms

commit 306b28f632e21b42ab165e7944283cf9764b590e
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Apr 23 14:23:26 2009 -0700

    Wrong license on ao_monitor.c

commit dca3a6de26d26c0020f3fb2cf5d8ac1552c195b1
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Apr 23 14:23:00 2009 -0700

    Crank up radio to 10dBm

commit fbe3096f7e9a8112dbc79f376eccdaa6872ae520
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 22 16:03:28 2009 -0700

    Add COPYING file

commit 9b7788f18bbaf3c4e5ebbf6c5ebd926468b0e045
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 22 15:55:01 2009 -0700

    Clean up TeleTerra files

commit 61cee50c86e275f9fde875bd317c3e74255394ec
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 22 15:53:55 2009 -0700

    simplify ao_time function

commit 3703ecdc9e190f2e0b7ead0e71b78be881c1f3b7
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 22 15:53:46 2009 -0700

    One line radio status

commit 1fbb3c17672a03ea6318fee07f9c2dcd7a8d0b16
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 22 15:49:16 2009 -0700

    Add new binaries to .gitignore

commit 00d5610caff61559eb24c24beaa56629d6bb03be
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 22 15:49:00 2009 -0700

    Speed up dbg port bit frobbing

commit c7555eb16876aa8ff9fe7f648d325a1b8fb54d23
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 22 15:48:28 2009 -0700

    Use sdcc from path

commit ada6dea04b94be016598566c4c13e6105aaec353
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 22 15:48:14 2009 -0700

    Clean up task list formatting

commit 0a1b2297ee9f5bbb918bd72f26088a3e0b84839a
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 22 15:47:57 2009 -0700

    Control radio monitoring with the M command

commit 837c620f07b63efc171be3ac14c78bc99adf7592
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 22 14:25:43 2009 -0700

    Shrink USB output buffers, work around USB packet errors

commit d87e9c25947d7cc2eba8894a524977f2c55a089a
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 21 02:07:24 2009 -0700

    Clean up telemetry now that all packets are the same

commit 1b333def5052d2ed47fdeaef23a897fe326f6340
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 21 02:07:08 2009 -0700

    Add longer debug delays to reset/debug_mode entry

commit d1887ded41a5bfec8e10e9fd736fa9444b9b6222
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 21 01:17:03 2009 -0700

    Fix up fancy dbg stuff. Add teleterra initial bits.
    
    The dbg stuff needed a bit of help to actually walk the tables; it appears
    that complex expressions confuse sdcc.
    
    This also adds primitive teleterra bits, but no UI, etc.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 43c8f7012102cdb591ace899420c10e4a78385ad
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Apr 20 23:33:41 2009 -0700

    Add radio support. Build separate executables for TeleMetrum and the TI dongle
    
    Ok, way too big a patch, but things were in rough shape.
    This patch adds support for the radio, both transmit and receive.
    Then, because I could no longer run the TeleMetrum code on the TI
    dongle, I ended up building a separate image for the TI board, which
    involved creating a mechanism for having multiple command sets and splitting
    code for different functions into different files.

commit 5be13b76a2e29b84cd6d1eec065e3354b0dafce5
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Apr 18 23:19:24 2009 -0700

    Start using pdata area for less-frequently used data

commit 3e18b5a0d4c7d84df98b6ed0b7783de1d42d45bf
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Apr 18 23:19:05 2009 -0700

    Slow down panic presentation

commit c4e983daa4579896b227fdcb2be43fad75e94307
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Apr 18 23:17:45 2009 -0700

    Parse GPS data locally. Add 'g' command to display recent GPS results.
    
    This parses the GPS GGA message and stores it in a global variable,
    protected by a mutex.

commit ed6f67dc47d750d5ff8bea63ae7cbb560689b9b6
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Apr 18 23:16:01 2009 -0700

    Add task names and 'T' command to show task status.
    
    The T command shows the current wchan and PC for each task in the system.

commit 3d5a5fc4db5f681e848202c4ee4099d2879677d6
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Apr 18 19:32:18 2009 -0700

    Fix GPL version at 2
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 022f83ca6fd589005d8eb3e25e633950fef69fa7
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 17 23:38:14 2009 -0700

    Add gps, debug dongle support and pressure alt tables
    
    GPS also pulled in serial support. The altitude tables take raw 11-bit
    pressure sample numbers and convert them to standard pressure altitude
    values.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 31fce622b1bab7e3f421069d7f6d4d9bdcd825de
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 17 10:32:45 2009 -0700

    Enable FEC in radio packets

commit 293a357911090a2f37bdd6f7ea96942079ffdf2e
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 17 10:29:42 2009 -0700

    Add CRC to radio packets

commit 20834caf01ddf481e8362b0d2627ef383a82e09d
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 17 10:23:10 2009 -0700

    Add data whitening

commit 94e5343a72121a81ab19bf5025e6b6fc9847eb4f
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 17 10:19:25 2009 -0700

    Add packet status byte defines

commit 04bc51c170c6f22bb5cc16867ce9a307818a7a00
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 17 10:11:31 2009 -0700

    Add separate xmit/recv programs to radio demo

commit fafe55c3405964e0defdf25b6c00236f9aaefbc5
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 17 10:11:11 2009 -0700

    Get env var for debug method selection

commit 26095fc0511ee0d5213f038986032f7c59964cf0
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Apr 17 10:10:47 2009 -0700

    Run-time selection between cp2103 and cc1111

commit 543bedde83cbce5145668e72965e02d892187b59
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Apr 16 20:38:14 2009 -0700

    Send data

commit 5e2393eb6b1a6d7b180bd63d5165ee7b7ff5f9e0
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 15 14:25:26 2009 -0700

    Move a bunch of variables from __data to __xdata

commit 4d1091d9bd121f05f5fe0a9c9d2bc0da8c562b9a
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 14 21:25:15 2009 -0700

    Slow down panic code, disable interrupts

commit 545478dd02eaeff6a65d318e722b1e4fce5e01b4
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 14 21:24:25 2009 -0700

    Keep reporting flight state while it changes

commit 9605045164882b4ca3d1317ac860b02513a51f30
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 14 21:23:55 2009 -0700

    use red LED to indicate system startup

commit dc844ee7e49a3b6145b3165252a592ed070d600f
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 14 21:23:13 2009 -0700

    Use ao_ee_flush_internal while holding mutex

commit 5e45d1c89b00e74d5b2730345843f43aab516af2
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 14 21:22:56 2009 -0700

    Leave beeping and lights to the flight code

commit 902c342289c1d13a4d55b9224acb6d67578b7a60
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 14 21:22:31 2009 -0700

    Make mutex functions reentrant

commit acc4fc635edb70ec1ba2dff9f7ac0c8542c72c47
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 14 19:08:01 2009 -0700

    Add in existing flight pieces: flight/report/log
    
    These pieces come from the old telemetrum firmware.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit ac99982b10fd5772218660137ee21db9b90cd885
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 14 14:21:56 2009 -0700

    Add eeprom driver and command loop
    
    This involved adding dma control and a mutex implementation.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit fbd8f4aff5058f4d371596b04715b7cb6d38e729
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 14 11:04:09 2009 -0700

    Switch from --model-large to --model-small
    
    This shrinks the application quite a bit, and should make it faster as well.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit fb63262699d3a6fbf347d24efda8b01f75b7d0d3
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Apr 14 10:02:19 2009 -0700

    Add comments, clean up white space, etc.
    
    Various clean ups now that the basic code appears to work.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 7e4abf3a40c39d0ce4f466281bef9a464df85dd4
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Apr 13 21:58:07 2009 -0700

    Switch USB to double-buffered

commit b56a44e48552bc32dbba9ff21770c370219a684a
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Apr 13 21:51:59 2009 -0700

    Fix USB input/output by reloading packet limits.
    
    The USB controller is reset during the connection process, which clears the
    packet limits set in the controller at initialization time. Reload those
    values when the configuration is set.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit cdaf3fc5802acf2ddc7972a15649ab0e1b31b873
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Apr 13 20:39:46 2009 -0700

    USB working up through reading strings

commit c5c1e3fb1c253d387be02c127253ac2a55d577b4
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Apr 13 13:51:08 2009 -0700

    Add USB support.
    
    This offers a single CDC ACM device over USB.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit f3f25a1cec7d2a034aa544569cfd23bea1a996c5
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 12 23:53:55 2009 -0700

    Add beep/led support.
    
    Support our P2_0 connected buzzer, and formalize LED output support.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit e14f07bfdb8824fc7ed6df1129c66ee39ffd6d54
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 12 23:17:16 2009 -0700

    Add A/D sampler
    
    Sample A/D at the timer tick, placing data in a ring
    of samples.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 823f4f92de0c1f8dd7a644a8e56ffe9822bee6e2
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 12 22:52:47 2009 -0700

    Add 100Hz timer
    
    Use Timer 1 to generate a 100Hz timer interrupt

commit 650a77e209dbb54c8d8fd9824cee430985564973
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 12 21:58:49 2009 -0700

    Update README

commit 870e98334018a66de8a6e4a659d2dc5dee1cbecf
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 12 21:52:56 2009 -0700

    GPL Version 2 only

commit 11c526bdcbf4012e18fbfdc29ca8832870ca38f0
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 12 21:47:32 2009 -0700

    Add load command to s51

commit 55402ba3e87fd699c51079843309f1f0d1534724
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 12 21:33:55 2009 -0700

    Make test more complicated

commit 3d3f849c9af9028f667cef4afedc0798d39a9efc
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 12 21:33:46 2009 -0700

    SP points at last pushed byte

commit f72c4cbc8fd9412dd1cce0fc446e7bbd2edc2d34
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 12 20:27:03 2009 -0700

    Add .gitignore

commit 1903a86bf2cc6b685ccc475e62eabe49a4ec5b43
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 12 20:25:39 2009 -0700

    Initial AltOS import

commit 5221dc63cf3a059a32aca2bfa7828c215be814a1
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Apr 12 12:38:58 2009 -0700

    Add ccdump

commit ee110425fb814780476d1d3d8a257af126f41763
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Apr 6 17:09:23 2009 -0700

    Bump buffer pointer as data is written to cc-usb

commit 2d9b8a83a2d9f495199033e43f519d26f27938fe
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Apr 6 11:31:49 2009 -0700

    Add support for a serial-connected custom debug dongle
    
    This uses the cc1111 board as a custom debug dongle with faster
    methods for communicating with the debug target.

commit 24edd56155ed0fa02fdd8f66fdc7aa5a1021bf7d
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 1 17:50:47 2009 -0700

    Reset cc1111 on s51 exit

commit 5fcfe854d29e1862d9a6adcbef3ef5119eb52fa3
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Apr 1 00:06:45 2009 -0700

    Add timer-based beep test

commit 91607bebdd167ac632aca4b66e22cb0cabdf0d20
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Mar 26 22:41:47 2009 -0700

    Add readline support to s51

commit 66ee94ed10e3d79b24f45a5c63e58456d4d30343
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 11:37:48 2009 -0700

    Deal with MSB-outputing DMA engine

commit d3732fd405af03c3752a84c4b78da7ef5ebd3744
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 11:14:03 2009 -0700

    Flip ADC bytes around

commit 50cc8e97e76d9b60c622962e1c74cf422dfb2c0f
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 11:01:30 2009 -0700

    Add spacing for serial adc data

commit 5577ca3762bfc000b0bc3782c73a8f95996a28a6
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 10:58:57 2009 -0700

    Inc only one on dest addr

commit 378227d869a3e8787c532c8c4e1563b44002c4b5
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 10:55:17 2009 -0700

    Dump remaining inputs

commit f54a41e37d6897db2e24fbc82880076b78a0ae41
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 10:50:36 2009 -0700

    Remove poll for ti demo button

commit 2b93a70fdd9e47e8195855451aa19ecad5d8b068
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 10:50:14 2009 -0700

    Add adc to serial conversion

commit d9fd548db15232e3a8823815962b252c7a5e7cba
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 10:04:50 2009 -0700

    Add ADC via DMA example

commit 61faf2b773300988fe27cfde5bc045be9950a1b0
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 09:45:14 2009 -0700

    Add DMA example

commit 7b3fdf5b42c9be9bebc1ceb7a52ff0f5a2a28fcd
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 01:05:36 2009 -0700

    Back to 0dBm

commit 31d59b88baa2cd96dc6263d1c5877283f2cd8c36
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 01:03:08 2009 -0700

    Make radio test compile again

commit 9ce713fdd19bf1a51370dacba3670504356c5c11
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 01:02:07 2009 -0700

    Wait for xtal to stabilize

commit ffd43886dc902f3bb7407294018e3d62cac39480
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 00:55:11 2009 -0700

    Check serial input

commit 029963cc94fbb47560118b5de73c537e2c14ed7c
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 00:50:02 2009 -0700

    Eliminate array walking

commit 019456a17d36f8f9f9b72cfbc980492175086d32
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 00:41:49 2009 -0700

    Add a per-char delay

commit cfaf187e96ba98eb8dd934409a10bc70273fe68a
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 00:36:35 2009 -0700

    Use UTX1IF to wait for serial TX complete

commit 006124529b243c7657a94312d2c868a82878d8bb
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 00:29:29 2009 -0700

    Send more interesting text

commit 5049acd3d1ae42304513f667f55a2ddffa4c685a
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 00:24:56 2009 -0700

    More random serial bit frobbing

commit 50bdc2407c674a4770912d3a626f36820a7f1527
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 00:13:15 2009 -0700

    Flip serial TX code around a bit

commit 7b7617e376afe0df1d505375b76198358330370c
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 00:09:47 2009 -0700

    Try serial polarity high/high

commit 18edacdb1e6e429cc29a164e22ef2a566096b9d9
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 00:06:32 2009 -0700

    Make serial test simpler

commit 62744c186792739c3bf5798c80ff87c69fbe2b65
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 25 00:03:45 2009 -0700

    Flip start/stop bits around

commit 9e96107d5d1a9681b07c36bb5860c748bfe10ec0
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 23:57:12 2009 -0700

    Stop high

commit c41ceb9a488b2209d1d3c09967d1473ce608030f
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 23:24:01 2009 -0700

    Change radio to -30dBm

commit c35de083ca3d4f362063b056a0fd74ffe629d168
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 23:11:48 2009 -0700

    Add serial test program

commit 8ecbd8734f0fb5588b2a8eb20720cfc6f43dfb47
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 22:37:38 2009 -0700

    Wait for xtal to stabilize after changing to 24MHz

commit e120269fc0f8e14ddf1755337b1d092173e16da2
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 22:21:31 2009 -0700

    Actually return byte read from SPI

commit de1ac6f99a1526fa840a52cfc10fa3edc0589bed
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 22:12:51 2009 -0700

    Clear UxCSR_TX_BYTE after transmitting a byte

commit 3ed3ff63e46767a256d30c5da5c52ae20089a91d
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 20:04:58 2009 -0700

    Led the LED turn on

commit 91b3a6ae74184692f45702587c4d678b2799ad8c
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 19:55:04 2009 -0700

    actually write and compare SPI test bits

commit 7de3a43887485c3c6cf52960376ccde33fb33985
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 19:54:02 2009 -0700

    Add USART-based SPI test code

commit ef0eef68280e9b6ca5e3bb71062e23054340e1ed
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 17:22:36 2009 -0700

    Change spi test string

commit 8131389ee5018c05b721146a98367150cf500fdf
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 17:15:09 2009 -0700

    Oops, not merging in the bit read for SPI test

commit 3429016d1359ec650993d2fb0596184e3f717871
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 17:04:45 2009 -0700

    Adjust clock/data phase for spi test

commit fedd18b28ea54e1dabcd2f9e8cab3ae4ee0fd070
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 16:35:13 2009 -0700

    MISO needs to be an input

commit f0c233f25a208a636833312b1766825815735304
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Mar 24 15:41:55 2009 -0700

    Add bit-banging spi eeprom test program

commit 6eeee64cf16ccc9218dbdde5426f25bda5e3407f
Author: Bdale Garbee <bdale@gag.com>
Date:   Wed Mar 18 02:58:33 2009 -0600

    working beep at around 4khz

commit 4726317de811c20e8d6754762437b5c9cbb3a48c
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Mar 18 01:54:34 2009 -0700

    Add simple test program to light up the transmitter at 434.550MHz
    
    This starts a transmit sequence, but doesn't send any data so the
    transmitter just locks on.

commit a0a27600ee2bf237e74eb83767a8d2e7c91df24f
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Mar 15 18:14:21 2009 -0700

    Correctly comment which bit the beep program uses

commit 25b77d236c01258abfc03114c2fc9ea2d69ca6e7
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Mar 15 18:11:53 2009 -0700

    Add telemetrum beeper example

commit 164b4e4749ad64ebbe26e84fd7b4fa1aa733dbe4
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Mar 15 18:11:20 2009 -0700

    sdcc gets the lib path correct based on the model

commit 04a316133af93b79bfbebb91f05eec1015ec2abc
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Mar 15 18:10:43 2009 -0700

    Bump debug speed back up

commit 9fd63972758d6d5572f7bcaadec9b1c0e974a2e8
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Mar 7 21:05:40 2009 -0800

    Only flip changing bits in async mode

commit c8fd04e154bcfd65ae1200980bd8163caabd7fe4
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Mar 7 21:05:06 2009 -0800

    The debug port only works if reset is higher than clock. weird

commit ade11f88754b4ab0386ebf86afc5257e59238f62
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Mar 7 21:04:38 2009 -0800

    Make manual bit flipping sync after every transaction

commit e63b5271bb54afc36e4b9891e51e053ff6011092
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Mar 7 14:49:22 2009 -0800

    Add ccmanual

commit 77d754afc2d14aaa4413c13ebe3777ef385f62a9
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Mar 7 14:48:49 2009 -0800

    Sync after manual bit reading

commit 5a338c8a7394d003355f96a8777b6fe83bb8493c
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Mar 7 14:48:35 2009 -0800

    Flip debug pins around to match telemetrum

commit cc0495b7028f4b1189a00707d828a68534d1dea2
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Mar 6 22:52:35 2009 -0800

    Wait for a while when switching the RESET_N line
    
    The cc1111 manual suggests placing a 2.7kΩ resister and 1nF capacitor on the
    RESET_N line to filter out noise. This increases the time necessary to reset
    the chip to several microseconds which is longer than the interval between
    two USB packets. Flush the USB packet queue and sleep for a while after
    changing the value on the RESET_N line to make sure the chip sees the state
    change.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 41289e6d8f1767547a33fea349866e928e44910f
Author: Bdale Garbee <bdale@gag.com>
Date:   Mon Mar 2 07:46:20 2009 -0700

    minor s51.1 formatting fixes
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit fdee231ed097a4348aee78fbd4aa92826b80de03
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Mar 1 23:12:31 2009 -0800

    Add s51 manual.
    
    This documents (briefly) the s51 hex debugging interface program, including
    some simple commands to test the operation of the system interactively.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit f7d91bd23b8214e09deae0aafb516331e934c49b
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Mar 1 18:43:03 2009 -0800

    Sometimes the link breaks and the GET_PC command returns garbage

commit 3cc8d11eb8d5d0b42141dd84a58d461287f59e3a
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Jan 25 08:38:48 2009 -0800

    Support 'set' command
    
    The 'set' command modifies target memory and registers
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 60940b4be23962db79b8e914ec943d0636dd68ad
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Jan 5 21:45:21 2009 -0800

    Expose ccdbg_set_clock API
    
    This allows applications to change the debug port clock
    rate on the fly.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit eb09e61b0682eb2aeac8e1a34d58b897ba6db8e7
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Jan 5 21:44:44 2009 -0800

    Use custom sdcc libraries (this needs to be configured...)
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 1ccfe0887c794397131ab1c986c25f66eea86a6c
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Jan 5 21:43:44 2009 -0800

    Have S51 ignore SIGINT while running under sdcdb.
    
    This prevents keyboard interrupts from accidentally stopping
    s51.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 7c03937b36aac82b08f4ea0c6da33a994fe15ec7
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Dec 30 22:40:13 2008 -0800

    Add simple and timer sample programs
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 6c2a65c743a4ffae96ed27dbc38c1bf9242ed1df
Author: Keith Packard <keithp@keithp.com>
Date:   Tue Dec 30 22:35:53 2008 -0800

    Save/restore registers to host during memory operations. Cache ROM data.
    
    Because the debug port uses instructions for most operations, the debug code
    will clobber registers used by the running program. Save and restore these
    to avoid corrupting application data.
    
    If the ROM file is known, use that to return data instead of fetching it
    from the target to improve performance.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit ea366058aa467a8a7caf17e7014758f3741ea7f7
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Dec 29 12:35:11 2008 -0800

    Fix flashing less than a full page of data. Verify page at a time.
    
    The 8051 flashing code requires special help with counts with non-zero low
    byte. Also, instead of verifying the entire flash contents at the end,
    verify each page as it goes.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit e0697186a2f9b6139636ff5d5c162879c85caf9c
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Dec 28 00:11:13 2008 -0800

    Use SFR access funcs. Support 'dump' command. Add -m (monitor) flag.
    
    Not all SFRs are visible in the unified address space, so the SFR-specific
    accessors are required.
    
    The dump command is the same as the various 'd*'
    commands, but also supports dumping program memory.
    
    The new -m (monitor) flag watches the command stream between s51 and sdcdb.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 23aca1fcbc169184e32d4ec19f28dd4fd4cfda36
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Dec 28 00:09:30 2008 -0800

    Save/restore regs when reading/writing memory. Add SFR access.
    
    The DPL and ACC registers are used by the memory access code,
    so they need to be saved and restored. Stuff them up high in ram for now;
    this should probably be fixed to pull them back to the host instead.
    
    Special SFR access is required as not all SFRs are visible in the unified
    address space.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 1405838160b69e2cda456e21502a1d03b3aa7548
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Dec 27 11:25:58 2008 -0800

    s51: get start address from ihx file. re-enable breakpoints after reset.
    
    Use the start of the ihx file when asked to run from 0x0, this lets
    sdcdb run programs from ram.
    
    The reset command clears all hw breakpoints, so reset them afterwards.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 1264c3676e95427bba5d01e05c303d036a7f9eca
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Dec 26 23:05:04 2008 -0800

    Switch to libusb-1.0 and use async interface.
    
    The async libusb interface offers substantial performance benefits by not
    making each command wait for the reply. This makes talking over this
    interface almost reasonable.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit d2d9cfd74fd66836c913c02276e09136d83b35dc
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Dec 26 17:58:48 2008 -0800

    s51: add breakpoints and the ability to block awaiting a breakpoint.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 4c4093c3fdd309123fdd068c0e1ff4947104492d
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Dec 22 19:11:56 2008 -0800

    Add more commands to s51 assembly-language debugger
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 55eba4fa08b022197106245d36a70f575a070b0a
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Dec 22 19:10:27 2008 -0800

    Make read_memory debug output use ccdbg_debug.
    
    This makes it default to not being presented, which makes s51 much happier
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit e75918f3667a5c8ad294bec4acef6fe81682edf6
Author: Keith Packard <keithp@keithp.com>
Date:   Sun Dec 21 23:33:35 2008 -0800

    Add preliminary version of s51, a UI clone of the 8051 emulator.
    
    sdcdb provides source-level debugging using the 8051 emulator, s51. By
    emulating that emulator a the UI level, we should be able to get source
    debugging right on our target platform.
    
    This is just the preliminary structure for the program with most commands
    not yet implemented.

commit f7d49868aeae80d515b12a7e339628f1296754a6
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Dec 20 23:30:06 2008 -0800

    Cleanup work; separating out the cp interface to be more abstract.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 30f23f23a6db3d12fdc9c088cf6ab47c5e5077fb
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Dec 19 21:13:04 2008 -0800

    Clean up autotools stuff.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 9025eb792861930e6af918d2727c4f5d97a69936
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Dec 19 21:11:45 2008 -0800

    Autotools.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit ab909db28307cfbf7ee8d692506bb79d7ffd627a
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Dec 19 19:08:13 2008 -0800

    Ignore .ihx files

commit cc8db276bc4f2fd7eb00168a5c0689a8457a5c6f
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Dec 19 19:07:37 2008 -0800

    Move blink example to subdir
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 82e2d7ebed6682062dc400478c736bd6c91195c9
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Dec 19 19:04:26 2008 -0800

    Clean up makefiles, move ihx files to .ihx

commit 52fb5f795adfd7f62e5b6dbe65877d14361cfdae
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Dec 19 14:39:57 2008 -0800

    ignore more stuff

commit 4ecfc33f16aa36b315519e6f279da65374b67aba
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Dec 19 14:37:53 2008 -0800

    Add cc1111 isr stub example

commit d32e6658c3e489b62ba3cf6d22e3ab177b9b8a3a
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Dec 19 14:37:29 2008 -0800

    Add blink-tiny flash and ram versions

commit b4d1127ef007843c643b778b3b2f6b915b1d5d9a
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Dec 19 14:19:29 2008 -0800

    Flash multiple pages. Eliminate off-by-one error in hex_image length.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 55995515b9d4fc1e193039eab697c5d03db417c2
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Dec 19 11:04:16 2008 -0800

    Add flash writing code.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 0bc52385b8f86f9ca1c450ad106e6d8afe3bc153
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Dec 18 12:37:32 2008 -0800

    faster
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 3779cc8b32cac3640f42bd0400d4199ddae965a1
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Dec 18 12:17:41 2008 -0800

    cq
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit dc03adc179669d41e3551d74b3c5a60db41ff217
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Dec 18 12:07:06 2008 -0800

    Add ability to load Intel HEX files. Add sample sdcc LED blinker.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 807e2adacb025af77bb53c03209e9c8e0d7a5f95
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Dec 18 00:18:50 2008 -0800

    Add ability to read/write arbitrary memory. Write LED blinker program.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 8c879bf51c14a5928135d59211facd72f6a32808
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Dec 17 23:15:47 2008 -0800

    Move manual bit-banging debug code to separate file
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit aec3bbce84a5ceb92060a4b3889379f2af2404ac
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Dec 17 23:15:19 2008 -0800

    reduce clock to 50us
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit fa168f963f8b00144d12aa2770e9c0917cfae123
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Dec 17 23:12:59 2008 -0800

    Fill out ccdbg-command to support all debug commands.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 5df84df7cd6a31527dcfd11030f00ef9d8abf170
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Dec 17 22:24:59 2008 -0800

    Clean up bitbanging layer. Add debug printfs.
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit 584e28bac8af38de433767e017977ed1adddeb36
Author: Keith Packard <keithp@keithp.com>
Date:   Wed Dec 17 12:32:15 2008 -0800

    Clean up sample debug files
    
    Signed-off-by: Keith Packard <keithp@keithp.com>

commit e64b4dbf15e9ee1cb0de002985de7575e83d46e9
Author: Keith Packard <keithp@keithp.com>
Date:   Mon Dec 8 17:25:28 2008 -0800

    Add support for input-only lines (-)

commit 4f38974a9941cddaba27c17c5a46f923db386c94
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Dec 6 16:32:27 2008 -0800

    Add another example

commit 3709ec3205cfb152b6568f3ea505c67fe7504c2a
Author: Keith Packard <keithp@keithp.com>
Date:   Sat Dec 6 16:32:12 2008 -0800

    Add libusb support and lots more examples

commit 39801e6e9fb9388072ee414a447f74095a6ac960
Author: Keith Packard <keithp@keithp.com>
Date:   Fri Nov 28 22:57:07 2008 -0800

    Random hacking

commit 01cb2799875e086ee6096627c058ee235bbc33d5
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Nov 27 17:07:15 2008 -0800

    Add prototypes, add stub mainline, add .gitignore

commit 0ffe4ef870b0e564789a1990aeab5b6651868e5b
Author: Keith Packard <keithp@keithp.com>
Date:   Thu Nov 27 12:33:40 2008 -0800

    cc1111 debug port access through cp2103 serial chip