]>
git.gag.com Git - fw/altos/log
Keith Packard [Fri, 16 May 2014 05:57:50 +0000 (23:57 -0600)]
altosui: Remove debug printf about beep config
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 16 May 2014 05:46:41 +0000 (23:46 -0600)]
altos: stm and lpc ao_boot.h were identical. move to kernel.
These two files were absolutely identical, so share them by moving
under kernel instead.x
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 16 May 2014 05:34:17 +0000 (23:34 -0600)]
altos: Use explicit boot loader signal in ao_boot_reboot
Instead of just "knowing" that ao_boot_loader will be passed zero when
the application wants to get back to the boot loader, explicitly
define the values so that both sides always agree.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 16 May 2014 05:10:54 +0000 (23:10 -0600)]
doc: Document the Apogee Lockout setting
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Thu, 15 May 2014 23:20:39 +0000 (17:20 -0600)]
include EasyMega Makefiles
Bdale Garbee [Thu, 15 May 2014 23:19:08 +0000 (17:19 -0600)]
working?
Bdale Garbee [Thu, 15 May 2014 22:23:17 +0000 (16:23 -0600)]
lose the (old) easymega-v1.0 directory in favor of my fresher 0.1
Keith Packard [Thu, 15 May 2014 15:31:24 +0000 (09:31 -0600)]
altos: Make quadrature debounce per-pin rather than per-device
Debouncing per-pin means we don't lose transitions, which makes
counting a lot more precise.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 15 May 2014 15:30:32 +0000 (09:30 -0600)]
altos/telemini-v2.0: Enable beep frequency configuration
Now that there's space for this, add it in.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 15 May 2014 15:29:52 +0000 (09:29 -0600)]
altos/telemini-v2.0: Remove old baro->alt conversion table
TeleMini doesn't have two baro sensors...
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 15 May 2014 15:28:30 +0000 (09:28 -0600)]
altos/cc1111: Switch P1_0 from a green LED to USB pullup
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 15 May 2014 15:27:34 +0000 (09:27 -0600)]
altos/cc1111: Add support for CPU-driven USB pullup
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 14 May 2014 05:46:19 +0000 (22:46 -0700)]
altos/cc1111: Errata fix isn't needed for discontinued products
And, doesn't fit in memory for some of them, so don't compile it.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 14 May 2014 00:30:47 +0000 (17:30 -0700)]
altos/cc1111: Wait for xtal to be stable
Errata http://www.ti.com/lit/er/swrz022c/swrz022c.pdf says that the
xtal is stable bit is bogus and that you need to just delay for a while.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 May 2014 06:21:55 +0000 (23:21 -0700)]
Merge remote-tracking branch 'origin/master'
Keith Packard [Tue, 13 May 2014 06:20:08 +0000 (23:20 -0700)]
ao-tools/ao-usbload: Check image flash usage against device flash availability
For devices which report the range of valid flash addresses from their
boot loader, check the loaded image to make sure it fits within that range.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 May 2014 06:18:41 +0000 (23:18 -0700)]
altos/flash-loader: Check memory addresses against flash space
This validates memory read/write requests to make sure they are within
the available flash memory space.
This also reports the flash base and bounds addresses in the 'version'
command so that the loader can validate the image before attempting to
write it.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 May 2014 05:56:38 +0000 (22:56 -0700)]
altos/stm: Use #define'd constants for GPIO register addresses
This lets the compiler short-circuit the tests in ao_enable_gpio and
ao_disable_gpio to save a bit of code space and time.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 May 2014 05:55:38 +0000 (22:55 -0700)]
altos/stm: Figure out available flash space based on chip id registers
Look at the flash size and the device id registers to figure out how
much flash is available.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 May 2014 05:54:35 +0000 (22:54 -0700)]
altos/stm: White space fix in ao_boot_pin.c
Keith Packard [Tue, 13 May 2014 05:53:07 +0000 (22:53 -0700)]
altos/stm: Use flash address of boot loader instead of 0x0
Flash is at 0x08000000, but when the chip boots, it can be at 0x0 as
well. Use the 0x08000000 address when rebooting to flash
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 May 2014 05:51:50 +0000 (22:51 -0700)]
altos: Assume all LPC products will have 32KB of flash
If we ever use something smaller than this, we'll need to figure out
how to tell how much memory the device has.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 May 2014 05:51:16 +0000 (22:51 -0700)]
altos: Report amount of program space available in the version command
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 May 2014 05:50:41 +0000 (22:50 -0700)]
altos: Add LED test command to pca9922 driver
This lets you control the LEDs from the command line to test things.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 May 2014 05:49:39 +0000 (22:49 -0700)]
ao-bringup: Use official binaries for EasyMini turnon
Don't use locally built ones, use the official ones found in
~/altusmetrumllc/Binaries to ensure that all devices are shipped with
known firmware.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 May 2014 05:48:45 +0000 (22:48 -0700)]
ao-bringup: test-baro should accept altitudes a bit below sea level
Testing baro sensors on a particularly high pressure day at Keith's
house yields altitudes down to -20m or so.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 13 May 2014 05:47:55 +0000 (22:47 -0700)]
atosui: Hide Callsign and RSSI tabs for devices without a radio
When doing Monitor Idle with EasyMini, it's nice to not put fields on
the screen which won't ever have useful data in them.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Mon, 12 May 2014 23:31:14 +0000 (17:31 -0600)]
update TeleMega turn-on script and Releasing for new stable firmware home
Bdale Garbee [Fri, 9 May 2014 18:30:25 +0000 (12:30 -0600)]
fix copyright year
Keith Packard [Fri, 9 May 2014 07:05:39 +0000 (00:05 -0700)]
altos: Simplify quadrature tracking
Set the timer to 200Hz for a 5ms debounce interval. Then, simply look
for transitions ending in both bits in the encoder being off, which
indicates the the encoder is resting in a detent. If bit '2' is
turning off, the encoder was rotated clockwise, otherwise the encoder
was rotated counter clockwise.
This is a lot more reliable, although still not perfect.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 6 May 2014 06:46:34 +0000 (23:46 -0700)]
altos: Clean up trailing whitespace in ao_pad.c
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 6 May 2014 06:45:30 +0000 (23:45 -0700)]
altos: Fix byte offsets in the mega AO_LOG_FLIGHT packets
Just comments, but even those should be correct
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 6 May 2014 06:43:44 +0000 (23:43 -0700)]
altos: ublox driver always offers course data when it has a fix
Set the AO_GPS_COURSE_VALID bit to signal that this part of the GPS
data is valid.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 6 May 2014 06:41:43 +0000 (23:41 -0700)]
altosui: Add GPS course, ground speed and climb rate to graphs
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 6 May 2014 06:38:44 +0000 (23:38 -0700)]
altoslib: Parse remaining mega AO_LOG_FLIGNT and AO_LOG_GPS_TIME fields
GPS fields past 'day' were not getting parsed. Ground values for the
IMU were not getting parsed, but a false 'temperature' value was being read.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 6 May 2014 06:38:05 +0000 (23:38 -0700)]
altoslib: Add a comment to remind us to fix the IMU code to deal with calibration
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 3 May 2014 17:58:31 +0000 (10:58 -0700)]
altos: 8051 64 * 16 multiply function was broken for negative 64-bit
It was jumping around the actual multiply when the 64-bit argument was negative.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Thu, 8 May 2014 22:24:26 +0000 (16:24 -0600)]
relay control implemented, this project is now complete
Bdale Garbee [Thu, 8 May 2014 22:09:11 +0000 (16:09 -0600)]
first cut of usbrelay-v0.1 support .. LEDs wiggle, not switching relay yet
Keith Packard [Fri, 2 May 2014 20:53:08 +0000 (13:53 -0700)]
altosui: Add configuration UI for beeper tone
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 2 May 2014 19:26:07 +0000 (12:26 -0700)]
altos: Add configurable beep tone
This lets you directly set the mid-range beep tone; the high and low
tones remain set off of that in the same ratio as before.
Note that none of the cc1111 products get this feature as they don't
have enough flash space anymore...
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 1 May 2014 05:14:37 +0000 (22:14 -0700)]
altos: For telelco discovery packets, retry 5 times with shorter timeout
A timeout of 10ms is more than enough to receive a query packet, but
if we miss it during device discovery, it's a pain, so retry 5 times
to make sure we find everyone.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 1 May 2014 05:13:44 +0000 (22:13 -0700)]
ao-tools: Clean up ao-sym structure an initializers
Remove unused 'default_addr' field. Use named initializers when
setting up the struct.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 1 May 2014 05:12:30 +0000 (22:12 -0700)]
ao-load: Make ao_sym static to avoid collision with ao-editaltos
ao-load doesn't use ao-editaltos at this point, but does share the
same name for the symbol table. To make the linker happier, make the
ao-load version static.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 1 May 2014 05:11:39 +0000 (22:11 -0700)]
ao-telem: Dump orientation field from TeleMega sensor telemetry packet
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 1 May 2014 05:10:29 +0000 (22:10 -0700)]
altosui: Mark TeleMega additional pyro ignitor fired points in graphs
Add markers to indicate when each additional pyro channel fires
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 1 May 2014 04:30:46 +0000 (21:30 -0700)]
altoslib: Track pyro firing state when reading mega eeprom files
TeleMega records whether each pyro has been fired in the eeprom file;
track that in the AltosState record.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 30 Apr 2014 02:04:30 +0000 (19:04 -0700)]
altosui: Add extra ignitors to graphable objects
List all of the available extra ignitors as possible things to graph.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Sun, 13 Apr 2014 14:58:36 +0000 (08:58 -0600)]
ugly hack (just make sleep longer) to work around ttyACM* discovery issue
Keith Packard [Sun, 13 Apr 2014 00:46:34 +0000 (17:46 -0700)]
altos: Switch beeping to farnsworth spacing
Use 17wpm/12wpm farnsworth spacing for the state reports. Leave the
numeric reports running slowly as those require counting.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 13 Apr 2014 00:45:38 +0000 (17:45 -0700)]
altosuilib: Make lines in graphs 2 units wide
This makes the graphs a lot easier to read.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 11 Apr 2014 23:40:06 +0000 (16:40 -0700)]
altoslib/altosui/altosuilib/libaltos: Remove trailing whitespace
Just cleaning up the source code.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 11 Apr 2014 23:31:32 +0000 (16:31 -0700)]
altos: Add 'microwater' product
This is a custom firmware spin for micropeak designed for use with
water rockets that sets the boost detect altitude to 10m instead of 30m.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 7 Apr 2014 06:46:48 +0000 (23:46 -0700)]
altosui: Disable flight log configuration while flights are stored
The log code won't let you resize the maximum flight log while there
is still data on the flight computer; the code to figure that out in
the UI was busted, leaving users confused about why it wasn't working.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 7 Apr 2014 05:27:37 +0000 (22:27 -0700)]
altos: Fix nanopeak compile
Nanopeak uses port B bit 3 for the LED instead of bit 4. Fix the async
code to support arbitrary bits for the serial LED.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 7 Apr 2014 03:14:49 +0000 (20:14 -0700)]
altos: Provide stable binaries for MicroPeak
Publish MicroPeak .hex file to LLC repo and install it from there,
rather than rebuilding it locally. This ensures that the installed
bits don't depend on local configuration of any kind.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 7 Apr 2014 02:48:07 +0000 (19:48 -0700)]
altos: Replace C code attiny async output with inline asm
Using inline asm instead of C ensures that compiler changes will not
affect the timing of the serial data.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 6 Apr 2014 01:17:17 +0000 (18:17 -0700)]
altos: Build TeleBalloon v2.0 by default
We're supporting this now, we might as well build it.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 6 Apr 2014 01:16:21 +0000 (18:16 -0700)]
ao-bringup: Split out easymini test into separate script
This lets you run the easy mini testing code without also flashing the device.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 6 Apr 2014 01:14:35 +0000 (18:14 -0700)]
altosui: Add ignitor tab for TeleMega extra ignitors
Show the current state of the additional ignitors in another tab;
there's not really room in the 'Pad' tab.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 5 Apr 2014 07:28:13 +0000 (00:28 -0700)]
doc: Document new voltage beeping at startup time
Keith Packard [Sat, 5 Apr 2014 07:20:22 +0000 (00:20 -0700)]
Bump version to 1.3.3
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 5 Apr 2014 07:18:57 +0000 (00:18 -0700)]
altos: Report battery voltage instead of S at startup
This works on everything with a beeper except TeleMetrum v1.0 which
just doesn't have enough flash space for the code.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 5 Apr 2014 06:40:22 +0000 (23:40 -0700)]
doc: Outline files are now generated, so don't put them in git
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 5 Apr 2014 06:38:40 +0000 (23:38 -0700)]
ao-tools: Wait for device to become ready instead of failing
For some reason, USB devices take 'a while' to become usable; instead
of bailing immediately, sit around waiting to see if the device
becomes usable if we get an EBUSY or EACCES error.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 5 Apr 2014 06:37:15 +0000 (23:37 -0700)]
ao-tools: Use 'program' command in ao-flash-lpc instead of 'flash'
The program meta-command is supposed to do the whole thing, and seems
more reliable in actually getting what we want flashed to the board.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 5 Apr 2014 06:36:34 +0000 (23:36 -0700)]
ao-bringup: Get turnon_telemini working
This script now does complete testing of the board
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 5 Apr 2014 06:34:48 +0000 (23:34 -0700)]
altos: Rename 'core' to 'kernel'
core remains a bad name to use -- dirvish skips files (and
directories, it seems) with that name.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 3 Apr 2014 07:10:19 +0000 (00:10 -0700)]
altoslib: Missed a couple of easy mini voltage API changes
Oh, and Tm was using Em conversions (which is almost right, except Tm
doesn't have the history)
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 3 Apr 2014 06:35:36 +0000 (23:35 -0700)]
Add easymini turnon script and helpers
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 3 Apr 2014 05:04:18 +0000 (22:04 -0700)]
altoslib: Fix EasyMini voltage computations
Early Em prototypes had a 3.0V regulator.
Early v1.0 boards measured power past the blocking diode.
Deal with both conditions to try and report more accurate voltages for
EasyMini data.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 3 Apr 2014 03:36:26 +0000 (20:36 -0700)]
altoslib: Ignore speed/accel after boost when finding maxima
Large spikes in acceleration often occur with ejection charges, which
can cause bogus acceleration and speed data to be seen. Ignore those
for the purpose of computing the maximum values of each.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 29 Mar 2014 06:33:25 +0000 (23:33 -0700)]
altos: HAS_LED is useless; remove it
ao_flight was trying to decide whether to turn off the red LED by
checking whether HAS_LED was defined. And yet, none of the flight
firmware defines that anymore, except for easymini which defines it to
zero.
Remove all uses and defines of this value, substituting AO_LED_RED in
ao_flight.c, which has to be defined for the ao_led_off call to work.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 17 Mar 2014 01:12:33 +0000 (18:12 -0700)]
Add easymega firmware
A trimmed down TeleMega build with no radio or GPS, along with pin
changes necessary for the device.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 11 Mar 2014 05:55:45 +0000 (22:55 -0700)]
altosui: Hide Tilt Angle values when not available
In the Ascent table, make sure the tilt angle fields are hidden when
they are set to MISSING.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 10 Mar 2014 04:10:10 +0000 (21:10 -0700)]
altos: Another missing usbtrng file
Keith Packard [Mon, 10 Mar 2014 04:08:25 +0000 (21:08 -0700)]
altos: Missing ao_pins files for usbtrng
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 10 Mar 2014 03:59:43 +0000 (20:59 -0700)]
altos: Fix LPC LED driver
Was using wrong types
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 10 Mar 2014 03:58:36 +0000 (20:58 -0700)]
altos: fix building LPC serial support for STDIO
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 10 Mar 2014 03:57:31 +0000 (20:57 -0700)]
altos: Don't require projects to define PACKET_HAS_SLAVE
Really, most don't need it, and whinging about not having it defined
isn't useful.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 9 Mar 2014 05:39:33 +0000 (21:39 -0800)]
Add USB True Random Number Generator product
Just basic device support
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 9 Mar 2014 00:25:33 +0000 (16:25 -0800)]
Re-add LCD bits to stm-demo
Keith Packard [Sun, 9 Mar 2014 00:25:10 +0000 (16:25 -0800)]
Add flash loader for stm-demo board
Keith Packard [Sat, 8 Mar 2014 05:27:26 +0000 (21:27 -0800)]
doc: Add separate outline pdf generation
This generates one-page pdf files that contain just the outline of
each product.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 1 Mar 2014 07:04:54 +0000 (23:04 -0800)]
Install .desktopfile as _SCRIPTS so they are left executable
.desktop files should be marked executable so that the desktop
environment knows they are correct.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 1 Mar 2014 05:16:57 +0000 (21:16 -0800)]
altosui: Retry device enumeration after rebooting for self flash
Windows takes 'a while' to include the rebooted device in the list of
available devices, so try a few times with a 100ms delay so that we
can avoid asking the user to select from an empty list.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 1 Mar 2014 05:16:36 +0000 (21:16 -0800)]
Mark development sequence to 1.3.3 by bumping version to 1.3.2.1
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 24 Feb 2014 01:42:08 +0000 (17:42 -0800)]
libaltos: Link so with -znoexecstack flag
This marks the library as not requiring an executable stack, which
openjdk prefers
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Thu, 20 Feb 2014 20:23:52 +0000 (13:23 -0700)]
Merge branch 'master' of ssh://git.gag.com/scm/git/fw/altos
Bdale Garbee [Thu, 20 Feb 2014 20:23:32 +0000 (13:23 -0700)]
update turnon scripts to store cal values
Bdale Garbee [Thu, 20 Feb 2014 20:23:20 +0000 (13:23 -0700)]
typo fixes from Matt Kraai
Keith Packard [Tue, 18 Feb 2014 17:47:51 +0000 (09:47 -0800)]
altos: Create balloon-specific load for TMv2 hardware
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 18 Feb 2014 17:46:17 +0000 (09:46 -0800)]
altos: Make balloon code run again
This fixes the balloon code so that it works with recent altos bits
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 18 Feb 2014 17:45:41 +0000 (09:45 -0800)]
altos: Set reasonable accel values when !HAS_ACCEL
This lets us use telemetrum log and telemetry formats for balloons
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 18 Feb 2014 17:44:52 +0000 (09:44 -0800)]
altos: Expose ao_usb_running globally
This lets other bits of the code know when USB has been connected.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 18 Feb 2014 17:43:43 +0000 (09:43 -0800)]
altos: Move balloon flight code to core
This lets us create more than one balloon product
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 18 Feb 2014 05:30:28 +0000 (21:30 -0800)]
doc: Need to publish .svg files as well
The drill templates are all .svg files that are referenced by the
generated html.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 18 Feb 2014 05:27:57 +0000 (21:27 -0800)]
Re-create drill templates
Using inkscape, the drill templates weren't getting printed
correctly. Switching to hand-generated svg fixes that.
The .xsl file is also fixed to really encourage the images to be
printed at exactly 100%.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Mon, 17 Feb 2014 07:15:58 +0000 (00:15 -0700)]
deliver images used in MicroPeak manual to web server, too
Bdale Garbee [Mon, 17 Feb 2014 07:10:05 +0000 (00:10 -0700)]
update copyright year assertion in MicroPeak manual, remember during releases