+ ao_adc = &ao_adc_ring[ao_flight_adc];
+ ao_flight_tick = ao_adc->tick;
+ ao_raw_pres = ao_adc->pres;
+ ao_flight_pres -= ao_flight_pres >> 4;
+ ao_flight_pres += ao_raw_pres >> 4;
+
+#if HAS_ACCEL
+ ao_raw_accel = ao_adc->accel;
+#if HAS_ACCEL_REF
+ /*
+ * Ok, the math here is a bit tricky.
+ *
+ * ao_raw_accel: ADC output for acceleration
+ * ao_accel_ref: ADC output for the 5V reference.
+ * ao_cook_accel: Corrected acceleration value
+ * Vcc: 3.3V supply to the CC1111
+ * Vac: 5V supply to the accelerometer
+ * accel: input voltage to accelerometer ADC pin
+ * ref: input voltage to 5V reference ADC pin
+ *
+ *
+ * Measured acceleration is ratiometric to Vcc:
+ *
+ * ao_raw_accel accel
+ * ------------ = -----
+ * 32767 Vcc
+ *
+ * Measured 5v reference is also ratiometric to Vcc:
+ *
+ * ao_accel_ref ref
+ * ------------ = -----
+ * 32767 Vcc
+ *
+ *
+ * ao_accel_ref = 32767 * (ref / Vcc)
+ *
+ * Acceleration is measured ratiometric to the 5V supply,
+ * so what we want is:
+ *
+ * ao_cook_accel accel
+ * ------------- = -----
+ * 32767 ref
+ *
+ *
+ * accel Vcc
+ * = ----- * ---
+ * Vcc ref
+ *
+ * ao_raw_accel 32767
+ * = ------------ * ------------
+ * 32737 ao_accel_ref
+ *
+ * Multiply through by 32767:
+ *
+ * ao_raw_accel * 32767
+ * ao_cook_accel = --------------------
+ * ao_accel_ref
+ *
+ * Now, the tricky part. Getting this to compile efficiently
+ * and keeping all of the values in-range.
+ *
+ * First off, we need to use a shift of 16 instead of * 32767 as SDCC
+ * does the obvious optimizations for byte-granularity shifts:
+ *
+ * ao_cook_accel = (ao_raw_accel << 16) / ao_accel_ref
+ *
+ * Next, lets check our input ranges:
+ *
+ * 0 <= ao_raw_accel <= 0x7fff (singled ended ADC conversion)
+ * 0x7000 <= ao_accel_ref <= 0x7fff (the 5V ref value is close to 0x7fff)
+ *
+ * Plugging in our input ranges, we get an output range of 0 - 0x12490,
+ * which is 17 bits. That won't work. If we take the accel ref and shift
+ * by a bit, we'll change its range:
+ *
+ * 0xe000 <= ao_accel_ref<<1 <= 0xfffe
+ *
+ * ao_cook_accel = (ao_raw_accel << 16) / (ao_accel_ref << 1)
+ *
+ * Now the output range is 0 - 0x9248, which nicely fits in 16 bits. It
+ * is, however, one bit too large for our signed computations. So, we
+ * take the result and shift that by a bit:
+ *
+ * ao_cook_accel = ((ao_raw_accel << 16) / (ao_accel_ref << 1)) >> 1
+ *
+ * This finally creates an output range of 0 - 0x4924. As the ADC only
+ * provides 11 bits of data, we haven't actually lost any precision,
+ * just dropped a bit of noise off the low end.
+ */
+ ao_raw_accel = (uint16_t) ((((uint32_t) ao_raw_accel << 16) / (ao_accel_ref[ao_flight_adc] << 1))) >> 1;
+ ao_adc->accel = ao_raw_accel;
+#endif