+++ /dev/null
-altos (1.6.5-1) unstable; urgency=medium
-
- [ Keith Packard ]
- * doc: Add install-html script
- * Bump android version to 13
- * ao-tools/ao-chaosread: Document length (-l) option
- * altosdroid: Deal with multiple installed android SDKs
- * Mark testing version 1.6.4.1
- * altosui: Deliver firmware for Tmega 2.0 and TBT 3.0 for Windows too
- * altos: Block interrupts while waking tasks sleeping on timers.
- * altos: Move comment in ao_sleep_for next to related code
- * altos/stm: remove ao_dma_abort
- * altos/stm: use 0xff for dma mutex value for allocated mutexes
- * altos/stm: Add more SPI status register bits
- * altos/stm: Change ao_spi_send_sync definition to take const source
- * altos: Add STM DMA debugging
- * altos: Add STM SPI debugging
- * altos/stm: move spi execution to common ao_spi_run
- * altos/stm: Clean up spi_enable/disable_index functions
- * altos/stm: Add better byte-level SPI api
- * altos/drivers: Use more reliable byte interface for CC1120 reception
- * altos: Add debug check for irq block when editing task queues
- * altos: cc1200: use FIFO threshold pin output for APRS buffering
- * altos: Make ao_delay(0) not wait forever
- * altos/telemini-v2.0: Remove show tasks command
- * altos: Make task list output more useful
- * altos/stm: clean up ao_exti_enable
- * altos: Leave USB enabled in flight with -DDEBUG=1
- * altos: Use FIFO_THR pin for cc1120 transmit buffering
- * Bump to testing version 1.6.4.2
- * altos/cc1111: Remove 'show tasks' command
- * Bump to 1.6.5. Add preliminary release notes
- * Credit Chuck Haskin for helping fix the SPI bug.
- * doc: Build 1.6.5 release notes
-
- [ Bdale Garbee ]
- * switch libgtk-3-bin build-dep to gtk-update-icon-cache, closes: #825455
- * updating ChangeLog for 1.6.5 release
-
- -- Bdale Garbee <bdale@gag.com> Mon, 04 Jul 2016 23:48:50 +0200
-
-altos (1.6.4-1) unstable; urgency=medium
-
- [ Keith Packard ]
- * altos/cc1111: Use SW to drive UART RTS pin
- * Bump version to 1.6.3.1
- * altosui/telegps: Ship firmware for new hardware
- * altosdroid: Check for closed before writing/reading bluetooth
- * Publish firmware with keithp-fat
- * Add TeleMega to spec list. Add TeleGPS RF output.
- * altoslib: Switch distance from m/ft to km/miles for large values
- * altoslib: Remove some debug printf calls
- * altosuilib: Rate limit map loading pacifier updates
- * altoslib: Allow map preloading to be aborted
- * altosdroid: Rate limit map loading pacifier
- * altosuilib: Don't flicker missing voltages when changing units
- * doc: Start update for 1.6.4
- * altoslib: Clean up map file and url handling
- * altosdroid: make disconnect stick past pause/restart
- * altoslib: Get rid of AltosMap from AltosMapLoader
- * telegps: Adapt to distance units switching changes
- * Bump android app version
- * Bump java library versions
- * Automatically run 'git submodule update' if necessary
- * altosui/telegps/micropeak: Handle both MULTI_LIB and non-MULTI_LIB builds
- * altoslib: Store common frequencies in library version-independent form
- * altoslib: Store saved state in version-independent format
- * altoslib: Allow empty values in AltosHashSet representation
- * altoslib: Set version and log space from AltosIdleFetch
- * altoslib: Add log_space to AltosState
- * altoslib: Add AltosIdleReader
- * telegps: Use log_space when flight_log_max is missing
- * telegps: Add monitor idle mode
- * altoslib: use miles for distances > 1000ft.
- * altosuilib: Have map preload respond to units and font size changes
- * altosuilib: Rename AltosUIMap*New.java to AltosUIMap*.java
- * doc: pad/idle indicator table was busted
- * altosuilib: Fill preload map on site or lat/lon change
- * altosuilib: Only display map debugging when serial_debug is enabled
- * telegps-v1.0: Document how SN 1959 was fixed
- * stmf0: Clear all USB state when resetting chip. Wakeup all sleepers
- * stmf0: Do not send more data than requested for GET_DESCRIPTOR
- * altos/lpc: Handle USB reset by resetting internal state
- * altos/stm: Handle USB reset in STM32L usb driver
- * altos/cc1115l: Reduce trace buffer size
- * altos/stmf0: Rework the sram allocation to save a few text bytes
- * altos/stmf0: Remove ao_usb_free
- * altosdroid: Auto save freq changes on 'ok'
- * altosui: Remove missing items from --summary output
- * altosuilib: Track open frames, exit when none remain
- * altosui: Don't open command window when --graph is provided
- * doc: Updates to 1.6.4 release notes.
- * altoslib: Switch preserved state format to JSON
- * altoslib: Remove AltosHashSet code
- * altoslib: Add null constructors to AltosQuaternion and AltosRotation
- * altoslib: Add JSON-based object saving/restoring code
- * altoslib: Use reflection JSON code for frequency preferences
- * altoslib: Improve AltosState save/restore debugging
- * altoslib: Get rid of manual JSON encoding stuff
- * altoslib: Add null constructor for AltosCompanion
- * altoslib: Add construction for remaining primitive array types to JSON
- * altoslib: Add back some JSON exception debugging printfs
- * altosui: Print filename before attempting to parse in --summary mode
- * altoslib: Stop reflective JSON class walk at Object instead of null
- * Bump version to 1.6.4
-
- [ Bdale Garbee ]
- * process updates made during 1.6.3 release cycle
- * extend "ok" temp range to 40C, since battery charger on bench can drive temp above 35C at times in Bdale and Robert's production testing
- * releasing 1.6.4
-
- -- Bdale Garbee <bdale@gag.com> Fri, 17 Jun 2016 10:02:32 -0600
-
-altos (1.6.3-1) unstable; urgency=medium
-
- [ Keith Packard ]
- * Releasing: Copy TeleMega v2.0 bits to Binaries
- * src/chaoskey-v0.1: Add HV enable support
- * altos/chaoskey: Add support for flipping between raw and cooked bits
- * altos/chaoskey: Delay ADC reading for 250ms at startup
- * altos: remove blank line in stmf0/ao_timer.c
- * altos/stmf0: Allow projects to specify non-default stack size
- * altos: Add power management APIs
- * altos/stmf0: Add suspend/resume support
- * altos: Allow USB drivers to skip CDC-ACM -specific descriptors
- * altos: Add power management to TRNG driver
- * altos/chaoskey-v0.1: Add power management and change USB classes
- * altos: Delay TRNG ADC long enough for HV supply to stabilize
- * altos: Add simple stats test to TRNG code
- * altos/stmf0: Add missing ao_gpio.c
- * altos: Another fix for non CDC-ACM devices
- * altos/stmf0: Fix location of device_id register
- * altos/chaoskey: Encode both hardware and software versions in product ID
- * altos/stmf0: Use device ID as usb serial number if requested
- * altos/chaoskey: Use SoC device ID as serial number
- * altos/chaoskey: Add another USB endpoint to read raw data
- * altos: Add ChaosKey v1.0 product
- * ao-bringup: Switch to v1.0 for chaoskey
- * ao-tools: Add ao-chaosread
- * altos/stmf0: Fix build without second USB IN endpoint
- * libaltos: jni_md.h moved to linux subdir in Java install
- * libaltos: Add unistd.h to get defines for various syscalls
- * altos: Expose fast timer API from kernel/
- * Change how we detect and install java
- * ao-tools/ao-dump-up: Remove spurious flight state strings
- * ao-tools/lib: Remove trailing whitespace from ao-elf.c
- * ao-tools/lib: Add ao_hex_image_cat function
- * ao-tools: Add ao-makebin
- * altos/stmf0: Construct .bin files for flash loaders
- * ao-bringup: Use dfu-util to install flash loader on chaoskey
- * libaltos: Add Windows BT support. Split into separate source files.
- * altosui: Delay between polling for igniter status in Fire Igniters
- * altosuilib: Note that Windows now supports Bluetooth
- * libaltos: Fix warning in linux libaltos code
- * altoslib: use env var LAUNCH_SITES to override default URL
- * altosuilib: Control map debugging output with Serial.debug
- * altosui,telegps: Do not allow radio calibration to be edited
- * altos/stm: Run scheduler code on interrupt stack
- * altos/stm: Validate current task SP in interrupt by looking at PSP
- * altos/stm: Allow apps to define different stack size
- * altos/lpc: Add fast timer
- * altos: Add one-byte SPI output routine for LPC and STM cores
- * altos: Allow for flight hardware without any ADC values
- * altos: Add Detherm log format (easymini without ADC)
- * altos: Use mini logging for detherm, just without ADC
- * altos/stmf0: Add SPI driver.
- * altos/stmf0: Support HPE clock source
- * doc: Note that EasyMega and TeleMega report A-D continuity
- * altos: Add detherm product
- * altos/stmf0: Add pwm and exti drivers
- * altos: Add ao_gpi_set/clr_bits functions
- * altos: Add easy mini plotting helper in test code
- * altos/detherm: Add ms5607 to detherm
- * altos/detherm: Add servo driver
- * altos: Support telefire products in cc1200 driver
- * altos: Add pad support for new telefire versions
- * altos: telefiretwo-v0.1 bits
- * altos: Allow for pad boxes with different sensor configurations
- * altos: Support pad/lco boxes with fixed box numbers
- * altos: Add TeleLCOTwo firmware
- * altos: Fix telefiretwo .gitignore
- * altos: Add ao_lco_two.c; alternate LCO interface code
- * altos: Use simpler debounce logic for buttons
- * altos/telelcotwo: Add idle timeout
- * Add TeleFireTwo v0.2 project
- * altos/stmf0: Fix external interrupts
- * altos/telefiretwo-v0.2: Change alarm names in comment
- * altosdroid: Don't set target location if lat/lon is MISSING
- * altoslib: Add debugging to AltosPreferences.state() etc
- * altoslib: Make AltosGPSSat implement Serializable
- * altoslib: switch from keySet() to keys() in altos map tiles
- * altos: avoid mixed declarations and code in ao_task.c
- * Update java library version numbers
- * AltosDroid play store keys have moved, update configure.ac
- * Prepare for new Android release by updating version number
- * libaltos: Fix for Mac OS X El Capitan
- * Add preliminary 1.6.3 release notes
- * altosdroid: Can only use message once
- * Bump version to 1.6.3
- * altosdroid: Track device location in app, not telemetry service
- * altosdroid: Redraw offline map when my location changes
- * altosdroid: Run even without Bluetooth
- * altoslib: Use feet per second for imperial speed
- * altoslib: Report exceptions caught while opening launch sites URL
- * altoslib: Don't try to drag lines around until map is loaded
- * Debug bits for telebt
- * altos: Use TXE instead of TC for serial on STM32l
- * altos/stm32l: Add support for software-driven HW flow control
- * altos/telebt-v3.0: Flip CTS/RTS pins for BT module
- * altos: Clear packet queue when starting packet master
- * altosdroid: Add idle mode monitoring, reboot. Start igniters
- * altosdroid: Split setup functions to separate dialog
- * Fix key in AndroidManifest.xml.in
- * altosdroid: Add configurable frequency set
- * altoslib: Make AltosPreferencesBackend abstract. Add set/put Serializable
- * doc: Add idle mode info to 1.6.3 release note
- * Revert "altos/stm: Run scheduler code on interrupt stack"
- * altosdroid: max height is a height, not a speed
- * altoslib: Correct stats for flights without a real landing
- * altoslib: Flush during set_state. Don't store listener state.
- * publish AltosDroid in keithp-fat target
- * altoslib: Deal with TeleMetrum v2.0 MMA6555 being inverted
- * altos: Make sure AO_MMA655X_INVERT is declared where needed
- * doc: Update AltosDroid chapter for 1.6.3
- * doc: 1.6.3 release notes note TeleBT rts/cts and TM 2.0 monitor idle fixes
- * micropeak: Change order of windows install so that java detect works
- * altoslib: Fix map preloading callbacks, run in separate thread
- * windows: Change install to look for browser in a different place
- * Ignore some built files for 1.6.3
-
- [ Robert Garbee ]
- * fix argument to ao-cal-freq so devices other than /dev/ttyACM0 work
-
- [ Bart Massey ]
- * Clean up stmf0 adc init.
- * altos: Fixed timing of panic display LED to be readable
-
- [ Justin Vreeland ]
- * Fix java class differing only by case
-
- [ Bdale Garbee ]
- * add beep to TeleMega turnon script
- * releasing 1.6.3
-
- -- Bdale Garbee <bdale@gag.com> Fri, 06 May 2016 18:14:11 -0600
-
-altos (1.6.2-1) unstable; urgency=medium
-
- [ Bdale Garbee ]
- * process updates from 1.6.1 release
- * move turnon_teledongle to new cal-freq code
- * add a paragraph about TeleBT battery charging to AltosDroid chapter in documentation
- * turnon script for TeleBT v3.0
- * apply wrap-and-sort to control files
- * add automatic Bluetooth functionality check to turnon_telebt
- * new build dependency on asciidoc
- * now building for m4, too
- * modify bringup scripts to handle TeleMega v2.0
- * modify release procedure to reflect Keith setting version in confgure.ac
- * submodule madness
- * one more time, with feeling .. this time, I've updated pdclib
- * update Changelog from git log
-
- [ Keith Packard ]
- * altoslib: Add companion telemetry data support
- * ao-telem: Add companion packet telemetry data printing
- * altos: Add HAS_COMPANION to new boards with companion connectors
- * altos/telefire: No reply for ARMED. Ignore time for FIRE.
- * altos: Provide direct segment driving interface for LCD displays
- * altos/telelco: Infrastructure changes for drag racing
- * altos/telelco: Add drag race UI
- * altoslib: Hide 'state' member and use accessor function
- * altoslib: Rotation off by factor of two
- * altos/telelco: Adjust drag race UI
- * altosdroid: Add minus sign and decimal point to lat/lon input fields
- * altosuilib: In display thread, set new state synchronously
- * altoslib: Make sure .eeprom download file is flushed on exception
- * Bump release number to 1.6.1.1
- * altoslib: Clean up remaining direct AltosState.state users
- * altoslib: Keep downloading when a parse error occurs
- * Create directory on keithp.com when uploading devel version
- * telelco: Fix pad reset to one on radio signal loss
- * doc: Force FOP to read images from doc directory
- * doc: Start doc transition to asciidoc
- * doc: Add asciidoc telemini v1.0
- * doc: Lots more conversion from docbook to asciidoc
- * doc: Add asciidoc version of altosui chapter.
- * doc: Add asciidoc version of Altos Droid manual
- * doc: Add updating firmware and using am products asciidoc bits
- * doc: Add titles to all figures
- * doc: Finish converting docs to asciidoc format
- * doc: Convert AltOS doc to asciidoc
- * doc: Convert telemetry and companion docs to asciidoc
- * doc: Minor makefile cleanups
- * doc: Switch to free fonts. Publish fonts with docs.
- * doc: Place html book contents on left side of page with separate scrollbar
- * doc: Split revhistory to separate file for html docs
- * doc: Get images and tables all centered and labeled
- * doc: Make pdf titles less ridiculously large
- * doc: verbose mode for a2x
- * altosui: telemini outline pdf changed name
- * doc: Add product logos to books
- * Break out common pieces from TeleGPS and AltusMetrum
- * doc: Reformat 'Using MicroPeak' section
- * doc: Provide more actual links instead of just chapter names
- * doc: Move pad beeps table to usage chapter
- * doc: Reformat html versions a bit
- * doc: Split out EasyMini into a separate manual
- * doc: Try a different trick for asciidoc build issues
- * doc: Construct html index for documentation
- * doc: Remove some bogus bits from am.css
- * ao-tools/ao-dbg: Stop using sigvec
- * altos: Add TeleMega v2.0, including PWM driver
- * altos: Get stm32l pwm driver working
- * altos: Set AO_PWM_TIMER_SCALE for telemega-v2.0
- * Switch TeleMega v2.0 to CC1200 radio chip
- * altos: Insert inter telemetry-packet delay
- * Elide pyro channel information from EasyMini docs
- * Elide flight computer info from APRS section of TeleGPS manual
- * altoslib: Remove debug message from AltosMap
- * Update java library versions
- * Add release notes for 1.6.2
- * altos: Set TeleMega v2.0 PWM to support servos
- * altos: Switch PWM constants to end up exposing µsec
- * Bump version to 1.6.2, altosdroid to 10
- * doc: Update copyright year in altusmetrum doc
- * doc: fix typo in using external active switch circuit section
- * doc: Remove telemini v2.0. Add telemega v2.0
- * doc: Remove extraneous 'first off' from legal paragraph
-
- -- Bdale Garbee <bdale@gag.com> Sun, 10 Jan 2016 19:11:18 -0700
-
-altos (1.6.1-1) unstable; urgency=medium
-
- [ Bdale Garbee ]
- * swap names so v3.0 is the default TeleDongle version to turn on
- * add debian branch spec to vcs-git: line in control so Debian tools work right
- * changelog for 1.6.1 release
-
- [ Tom Marble ]
- * Minor typo in man page
- * Added continuous output option to ao-usbtrng
-
- [ Keith Packard ]
- * altos/stmf0: Add ao_crc_stm.c
- * altos: Replace ao_alarm/ao_clear_alarm with ao_sleep_for
- * altosui: Run all igniter status requests from non-GUI thread
- * altosuilib: Detect pair programming by product name, not USB id
- * ao-bringup/turnon_telemini: Detect which programmer to use by $USER
- * altos: embed ao_alarm and ao_clear_alarm in ao_sleep_for
- * altos/cc1200: Adjust bit-sync configuration
- * altos: Remove some accidental debug printfs from ao_packet.c
- * ao-bringup: Changes for telebt for keith's hacking
- * altosdroid: Lots of bluetooth connection changes
- * altosdroid: Explicitly disconnect BT on termination or 'disconnect'
- * altosdroid: Only speak when GUI is running
- * altosdroid: Missing file: DeviceAddress.java
- * altosdroid: Ignore automatic tab changing while activity is saved
- * altos: Allow software to offer other USB interface classes than CDC
- * altos/stmf0: Fix fast ADC interface
- * altos/stmf0: Typo in ao_crc_stm.c
- * altos/stmf0: Allocate USB buffers at startup
- * altos: Create chaoskey product
- * altos: Add chaoskey flash loader
- * altos/usbtrng: Split out random number generating code to separate driver
- * altos: Make APRS format (compressed/uncompressed) configurable
- * altosui/telegps: Add config option for APRS format
- * altoslib: Round frequency when configuring radio
- * ao-tools: Add ao-flash-stm32f0x
- * altos: Wait for BT disconnect before sending command
- * altos: Missing pad field in TMv2 data packet
- * altosui/telegps: Change from variable-units snuck into master
- * altosdroid: Deal with bluetooth connection failures better
- * doc: Update telemetry docs to include new packet formats
- * altos: Add .gitignore for chaoskey
- * altos: Build chaoskey by default
- * altos: Add makefile for chaoskey flash loader
- * altos/stmf0: Need ao_exti.h for pin configuration
- * altosui: Add map to MonitorIdle display
- * ao-tools/ao-mega: Clean up formatting of pyro status messages
- * altos/test: Make aprs test code compile again
- * altos/test: Support old telemega eeprom file formats in ao_flight_test
- * ao-tools/ao-list: Show devices that have no TTY
- * altos: Add the ability to configure a different USB vendor ID
- * altos/chaoskey: Set USB VID/PID to 0x1d50/0x60c6
- * altos/stmf0: Have fast ADC ring buffer code use wrap-around
- * icon: Convert windows stub into launcher program
- * windows: Use new windows stub to launch applications
- * altosdroid: Add USB support for TeleDongle/TeleBT
- * altosdroid: Fix tab label height problems
- * altoslib: Use Locale.ROOT for KML export
- * altoslib: Expose locale and non-locale floating point parsing functions
- * altosui: Remove un-implemented --fetchmaps argument
- * ao-dump-up: Add --wait option to make testing µPusb easier
- * doc: Clarify what 'after motor' means
- * altos: Support 32MHz xtal on cc1200
- * microsplash: Add 'publish' target to Makefile
- * micropeak: Use fast load mode by default in -load script
- * Flip version to 1.6.0.2
- * altoslib: Create display-independent map support code
- * telefire: Make 'good' RSSI value configurable
- * altos: Only set CMAC RSSI value on valid packet received
- * telefire: Report telefire battery voltage over telemetry link
- * altos: Add telelco v0.3 (v0.2 with cc1200 instead of cc1120)
- * altos/telelco: Display telefire battery voltage
- * altos/telelco: Show box voltage with pad knob instead of firing button
- * altoslib: Build AltosVersion.java in configure.ac
- * altoslib: Get new abstract mapping code compiling
- * altoslib: More frobbing with new map bits
- * altoslib/altosuilib: Update library version to 7
- * altoslib/altosuilib: Get new Map display code running in altosui and telegps
- * altosuilib: Add AltosUIImage.java
- * altosuilib: Use new map code for map preload UI
- * altosuilib: Remove old map bits
- * altosuilib: Get rid of AltosUIVersion.java
- * altosdroid: Add offline map tab
- * altosdroid: Move pause before reopening bluetooth into connec thread
- * altosdroid: Centralize debug printf code
- * altosdroid: Place icons on screen instead of drawing path
- * altoslib: Add AltosLaunchSite bits
- * altosuilib: Use altoslib site list loader
- * altoslib: Start with map empty
- * altoslib: Provide toString method for AltosLatLon
- * altoslib: Add map loading helper class
- * altosuilib: Switch to altoslib map loading code
- * altosuilib: Get rid of AltosUIMapNew.set_load_params
- * altosuilib: Eliminate extra MapCache in AltosUIMapPreloadNew
- * altoslib: Pass all map loader params to set_load_params
- * altosdroid: Add map types and map preloading UIs
- * altosdroid: Look for zipalign in the new place too
- * altosdroid: Disable debug output on release builds
- * altosdroid: Save selected map type in AltosDroid object
- * altosdroid: Add 'Current Location' as an option when preloading maps
- * altosdroid: Split out AltosMapView into separate file
- * altosdroid: Missing call to super.onDetach from TabMapOffline
- * altosdroid: use 'show' to set new tab contents in onResume
- * altoslib: Require 'debug' hook in AltosMapInterface
- * altosdroid: Switch from custom title to standard Holo theme
- * altosdroid: Highlight age in red when older than 10 seconds
- * ao-tools: Create ao-cal-freq
- * ao-bringup: Use new ao-cal-freq program for cal-freq script
- * ao-bringup: Do telegps freq cal before testing GPS
- * ao-tools: Add missing ao-cal-freq man page
- * altoslib: Add preferences for saving/restoring multiple flight states
- * altosdroid: Add multi-tracker support
- * altosdroid: Note recent changes
- * altosdroid: Resource changes needed for multi-tracker mode
- * altoslib: Set product for idle monitor
- * altoslib: Let the application disable the link cancel dialog
- * altoslib: Expose public function to set state.product
- * altoslib: Remove debug output from AltosMap
- * altosuilib: Show state.product if state.device_type isn't set
- * altosuilib: Create grid-bag helper functions in AltosUIFrame
- * micropeak: Update mac/windows FTDI drivers
- * telegps: use new AltosUIFrame constraint helper
- * ao-bringup: Fail turnon_easymega if accel cal fails
- * ao-bringup: Use local versions of tools instead of /usr/bin for turnon_easymega
- * ao-bringup: Make turnon_easymega run without 'make install'
- * altoslib/altosuilib: Fix equals methods, add hashCode
- * altoslib: Clean up map tile removal
- * altosuilib: Allow for no transform in map mouse wheel function
- * altosdroid: Switch trackers automatically when changing freq or baud
- * altosdroid: Remove debug
- * altosdroid: Support for sorting rockets by age
- * altosdroid: Stack map markers with newest rocket on top
- * altosdroid: Multiple tracker support for google maps
- * altoslib: Add set_zoom_centre to AltosMap
- * altosuilib: Use AltosMap set_zoom_centre instead of in-line version
- * altosdroid: Use AltosMap set_zoom_centre
- * altosdroid: Show receiver battery voltage in the 'pad' view
- * altosdroid: Add map source preference
- * altosdroid: Display online/offline maps in same tab
- * altosdroid: Get rid of on-line only maps tab
- * altosdroid: Select tracker by clicking on map
- * altosdroid: Switch to four tabs (pad/flight/recover/map)
- * altosdroid: Allow tracker selection from online map widget
- * altosdroid: Mark four-tab change done
- * altosdroid: Fix line drawing to old tracker location
- * altoslib: Use a longer filter for descent values
- * altosdroid: Show direction to target in recover tab
- * altosdroid: Define strings for the tab names
- * altosdroid: Change voice output around
- * altoslib: Typo slipped into AltosState.java
- * altosdroid: Make sure whole flight state is spoken even when no-one is moving
- * altosdroid: Make sure flight voice output always starts with 'speed'
- * altosdroid: Mark tab-dependent voice output as done
- * altosdroid: Update version numbers in manifest
- * Bump version to 1.6.0.3
- * altoslib: Fix replay to run in realtime again
- * altosdroid: Display direction in map view
- * altosdroid: Class of offline map view widget changed
- * altoslib: Don't crash if dragging a map view without any tiles
- * altos/telebt-v3.0: Report battery voltage correctly
- * altoslib: Support TeleBT v3.0 battery voltage conversion
- * altosuilib: Receiver battery voltage lives in listener_state
- * altosui: Correctly show/hide receiver battery value
- * telegps: Add receiver battery to Status display
- * altoslib: Make AltosMap floor/ceil static. Check transform in paint
- * altoslib: Make earth size constants public
- * altoslib: Limit simultanous map tile downloads to 128
- * altoslib: Convert longitude from distance in AltosMapTransform
- * altoslib: Preload maps based on distance rather than number of tiles
- * altosdroid: Keep speaking even when screen is off
- * altosdroid: Pop up menu of nearby trackers on map click
- * altosdroid: Remove a debug line in AltosVoice
- * altosdroid: Don't disconnect from bluetooth onStartCommand
- * altosdroid: Add other igniter status, various other layout changes
- * Generate Android version info from configure.ac
- * altosdroid: Note time at startup to avoid flipping trackers
- * altosdroid: Add 'Auto' to map tracker list
- * altosdroid: Clean up tab layout
- * altosdroid: Cleanup Makefile.am
- * Bump version to 1.6.0.4 (android version 8)
- * doc: Update for 1.6.1
- * Bump configure.ac versions to 1.6.1
- * Bump Java library versions
-
- [ Robert Garbee ]
- * add beep when test completes
-
- -- Bdale Garbee <bdale@gag.com> Thu, 16 Jul 2015 13:38:22 -0600
-
-altos (1.6-1) unstable; urgency=medium
-
- [ Keith Packard ]
- * altoslib: Stop re-loading previous flight when starting telemetry monitoring
- * telegps: Was mis-configuring the 'Configure Device' dialog
- * altos: Fix ability to disable telemetry by setting interval to 0
- * altos/test: Add TMv2 test program to .gitignore
- * altos: Add smaller altitude table file to .gitignore
- * altos: Make sure we don't beep out continuity twice in idle mode
- * altosui: Ignore built .desktop file
- * ao-bringup: Use C version of test-flash for telegps
- * ao-tools: Add ao-test-gps program
- * ao-bringup: Use C version of ao-test-gps in test-telegps
- * ao-tools/ao-test-gps: Improve output formatting
- * ao-tools/ao-test-igniter: Remove bogus printf
- * ao-bringup: Improve igniter testing. Add TeleMega and TeleMetrum testing.
- * Mark master branch as past the 1.5 point
- * altosdroid: Update version code and name for 1.5
- * altosdroid: Automatically sign the released version if the key is available
- * altosui: Fix --replay to run in realtime after boost
- * altosui: Bring up main window when doing --replay or --graph
- * altosdroid: Update notebook to reflect current status
- * altos: Make sure we drop the SPI mutex when aborting cc1120 recv
- * ao-bringup: Auto-select programmer for teledongle turnon
- * altos: Handle antenna down in ao_flight_test
- * altosui: Check for map and stats table when changing units/fonts in graph
- * altos: Record 32-bits for gyro calibration values
- * altoslib: Deal with new Mega log format that has 32-bit gyro cal
- * altosui: Update 'Imperial Units' checkbox when units change
- * altoslib: Compute tilt angle from eeprom data
- * altos: Fix syntax error with ao_log_mega change.
- * altos: Copy cc1120 driver to cc1200 driver and hack a bit
- * altos: Add prototype TeleDongle v1.9 code
- * altoslib: synchronize access to serial debug output list
- * altosuilib: Try to detect the architecture when loading JNI lib
- * ao-tools/ao-send-telem: Add verbose, fake and rate options
- * altos: Mark STM ao_spi_send as taking const pointer
- * altos: Expose telemetry altitude macros even without GPS
- * altos: Complete cc1200 driver
- * altos/teledongle-v1.9: Add remaining code to complete the project
- * altos: Sort out ao_gps_print altitude fetching
- * altos: Increase PQT value for cc1200 improving sensitivity
- * altos: Build TeleDongle v1.9 by default
- * altos: Remove old AO_SEND_ALL_BARO bits
- * altos: Perform cc1200 calibration less often. Tweak radio params
- * altos: Fix up telemetry delay computations
- * altos: Increase CC1200 SPI data rate to 8MHz
- * altosui: Pop up 'Connecting' dialog during Monitor Idle
- * altos: Rename microwater to microsplash
- * Move teledongle 1.9 to 1.8; there's a new 1.9
- * altos: Declare port register type only in arch header
- * altos: Stop attempting to ramp power on CC115L
- * altos: Use AO_SPO_SPEED_FAST for CC1200
- * altosuilib: GPS errors are recorded in floating point, not integers
- * altos: Use other TeleDongle LED for CRC-invalid packet reporting
- * altos/lpc: Declare SPI send parameters as const
- * altos/lpc: Disable JTAG when using pins for GPIO
- * altos/teledongle-v1.9: Switch to NXP processor as on prototype boards
- * altos: Reset interrupt flags before TX in CC1200 driver
- * altoslib: Missing headers for mag sensor in CSV output
- * altoslib: Make AltosState serializable
- * altosdroid: Don't display MISSING flight number
- * altoslib: Add getBytes/putBytes interface to AltosPreferencesBackend
- * altosdroid: TabMap needs to expose () constructor
- * altoslib: add AltosPreferences state save/restore interfaces
- * altosdroid: Save AltosState and restore at startup
- * altosdroid: East and West were flipped in all GPS output
- * Add AltosDroid release note for version 1.5
- * altos/microsplash: fix .gitignore to ignore resulting binary
- * altosui: Remove duplicate AltosUIPreferencesBackend.java
- * altos: Allow TeleMega to be built without MPU6000
- * altos/teledongle-v1.8: Make this the same as teledongle v1.9
- * altos/cc1200: Wait for packet to be placed in FIFO during receive
- * altos/cc1200: Open up preamble detect to improve sensitivity
- * altos/cc1200: With PQT wide open, we can't use PQT_REACHED for start
- * altoslib: Add usbtrng, usbrelay and mpusb USB ids
- * micropeak: Support µPUSB with our own USB ids
- * ao-bringup: Clear pending output before setting frequency.
- * altos: Document cc115l power measured at RF setting 0x03 as -31.75dBm
- * altos: Adjust CC1200 RSSI reporting value
- * altos/lpc: Switch LPC SPI driver to interrupt-driven
- * Set version to 1.5.9.1
- * altos: Get rid of some accidental debug code
- * altos/lpc: Fix double-buffered USB changes
- * altos: Add support for TeleBT v3.0
- * altos: Initial STMF04x support
- * altos: USBtrng v2.0 hardware bringup
- * altos: Add self-flash support for STM32F042 processor
- * altos: Add flash-loader to usbtrng-v2.0
- * ao-tools: Add --wait option to ao-usbload
- * altos/stmf0: Fix linker scripts to make ao_boot work
- * altos/stmf0: Add faster USB path
- * altos/stmf0: Add ADC and DMA APIs
- * altos/usbtrng-v2.0: Add random output command
- * altos/stm: Fix typo in stm32l.h
- * ao-tools: Add ao-usbtrng to dump RNG data for testing
- * altos/stmf0: Remove remaining stm32l bits from stm32f0 code
- * altos/stmf0: Add CRC driver
- * altos/usbtrng-v2.0: Use stmf042 hardware CRC unit
- * altos/stmf0: Re-implement fast ADC code for stmf0
- * Oops, forgot the TeleBT-v3.0 Makefile
- * And, also add the TeleBT v3.0 flash loader Makefile
- * altos/stm: Add ability to delay STDIO usage for serial ports
- * altos/btm: Add fancier debug. Pull serial reset port low.
- * altos: Always include a check for stdio overflow
- * altos/telebt-v3.0: Fix stdio setup for BTM
- * altos/telebt-v3.0: Turn red LED off after initialization
- * altos/stmf0: Support PA11/PA12 remapping
- * altos/usbtrng-v2.0: Select PA11/PA12 mapping config value
- * altos/telebt-v3.0: Add monitor bits
- * altos/telebt-v3.0: Set initial radio cal to a sensible value
- * altos: Rename teledongle-v1.9 as teledongle-v3.0
- * ao-bringup: Add turnon_teledonglev3
- * Revert "altos/lpc: Fix double-buffered USB changes"
- * Revert LPC usb performance improvements
- * altos/teledongle-v3.0: Shrink stacks to 320 bytes to fit in ram
- * altos/easymini-v1.0: Shrink stack to deal with USB changes
- * altos/lpc: Clean up USB endpoint access functions
- * altos/lpc: Double buffer USB data transfers
- * Update docs for 1.6
- * libaltos: Use more SetupDi API to get Windows 7 listing devices
- * Add 'keithp-fat' target for uploading temporary builds to keithp's machine
- * windows: Look for current Java version in \SOFTWARE\Wow6432Node
- * micropeak: Fix file association registry install on Windows
- * micropeak: Support both FTDI and Altus Metrum USB IDs
- * micropeak: Install Windows AltusMetrum driver bits
- * altosuilib: New teledongle and telebt devices are not pair-programmed
- * Package TeleDongle-v3.0 firmware with TeleGPS and AltosUI apps
- * altoslib: Store MS5607 data in AltosConfigData for use by AltosMs5607
- * altosuilib: EEProm download from TeleGPS doesn't have states
- * altosuilib: Don't show 'Sats in view' for TeleGPS eeprom graphing
- * altoslib: Support TeleGPS for Monitor Idle
- * altoslib: Use 'stateless' for Monitor Idle
- * altoslib: Initialize GPS data to MISSING for Monitor Idle mode
- * altos/drivers: Increase SPI speed of CC115L to 6MHz
- * altos/lpc: Give up on interrupt-driven SPI driver
- * altos: Separate out ao_tracker force from dbg
- * Update version 1.6 release notes with more bug fixes
- * altos: ao_packet_getchar needs to return 'int' so AO_READ_AGAIN works
- * altosui: Remove the dregs of AltosDroid load-old-telem code
- * altoslib: Mark listener as 'not running' on EOF.
- * altosuilib: Wait for product data while scanning
- * altoslib: Drop telemetry packets processed while monitoring is disabled
- * altosuilib: Reset telemetry state after processing it
- * altoslib: Clear saved TelemetryReader state instead of resetting in ScanUI
- * altosuilib: Set the icon and title of the telemetry scanning dialog
- * doc: update 1.6 release notes with recent bug fixes
- * altosuilib: Get the Eeprom download progress bar working again
- * altosuilib: Don't offer to graph some GPS details that TM doesn't log
- * Bump java library versions
-
- [ Bdale Garbee ]
- * updated to reflect changes from 1.5 release
- * reflect filename changes in LLC repo
- * store cal value correctly even when we didn't need to change it
- * document pyro current limits in an appendix
- * improve test procedures for TeleMega
- * document addition of TeleDongle to the set of ARM targets to save binaries for
- * update ChangeLog for release
-
- -- Bdale Garbee <bdale@gag.com> Sat, 07 Feb 2015 22:40:49 -0700
-
-altos (1.5-1) unstable; urgency=medium
-
- [ Bdale Garbee ]
- * notes updated for TeleGPS and 1.4 release learnings
- * make sure to use Google Maps API key for official builds
- * need the api key in Bdale's root too
- * update Releasing file based on learnings from 1.4.1 release
- * Windows sucks, hard .. make sure filenames are legal in .mdwn files
- * note need to push the updated repo with production binaries during release
- * update turnon tools
- * change easymega from v0.1 to v1.0, tweak to build on master, add to Makefile
- * turn echo back on after accel cal in turnon_telemetrum so rest is easier
- * tweaking test scripts
- * releasing version 1.5
- * updated ChangeLog for 1.5 release
- * update changelog for Debian build
- * capture deleted file
- * more build dependencies for processing icons
- * more build dependencies for processing icons
- * update ChangeLog
- * update changelog for Debian build
- * another build dep
- * use dh_installmime, which requires telling configure to stay out of the way
- * another build dep
- * use dh_installmime, which requires telling configure to stay out of the way
- * update changelog for release
- * update changelog for Debian build
- * need multi-arch in fat build
- * ignore cal_values file in bringup directory
- * updated ChangeLog for release
-
- [ Keith Packard ]
- * doc: Add instructions for flash recovery technique
- * altos/micropeak: Create a script to load firmware.
- * altosui/telegps: Use menus for frequency list and telemetry formats
- * altosuilib: Move menu bars into the Mac OS X top bar
- * altosui: Fix ground station configure frequency list
- * java: Bump java library versions for next release
- * altos/micropeak: Add load script template
- * Sign our .inf file with the comodo key. Update signing-driver
- * Fix java version detection and downloading
- * icon: Construct .exe files to hold windows icons for file associations
- * windows installer: Create file associations for Windows.
- * macosx: Define icons for our file types on OS X
- * altosui: Ship TeleMetrum v2.0 firmware with AltosUI
- * altosuilib: Hook up apple messages to callbacks
- * macosx: Respond to apple messages in all apps
- * windows: Missed adding 'refresh-sh.nsh'
- * linux: .desktop files must begin with organization name
- * Rename icon files to fit XDG specifications. Add file icons. Add mime types
- * altosuilib: Wrap radio frequency menu in JMenuBar when used in config
- * altos/aprs: Encode last serial number in SSID. Transmit serial in comment
- * altosui: Add Ignitor tab to Monitor Idle mode
- * altos: Make APRS SSID configurable
- * altosui/telegps: Expose configurable APRS SSID
- * ao-tools: Add ao-test-baro, ao-test-igniter and ao-test-flash
- * ao-bringup: Use the C tools to test EasyMini
- * altos: Add optional debugging to print out pyro firing status
- * altos/ao_flight_test: Get the Tmega version compiling again
- * Bump version to 1.4.1.1
- * altosuilib: Make map cache size configurable
- * altosuilib: Outline map lines and distance value with white
- * icon: Generate altusmetrum.xpm and install it
- * altosuilib: Mark 'Configure AltosUI' window with maps key status
- * Clean all .desktop files, ignore them too
- * Add 1.4.1 release notes
- * Add note about including Google maps API key
- * altosui: Don't show the tracker motion value when switching units
- * telegps: Disable tracker config when not available
- * altosui/telegps: Undo the frequency/telemetry menu changes
- * altoslib: Disable telemetry while getting config data
- * altoslib: Preserve receiver_serial across state reset for new transmitter
- * altosuilib: Remove debug printfs from map cache
- * altos: ao_rssi subsystem needs to use AO_LED_TYPE instead of uint8_t
- * altos: Stop sticking cc1111 firmware in src directory
- * altos: Use TeleMetrum v1.9 board for MegaDongle experiments
- * altos: Reduce configuration data telemetry to once per 5 seconds
- * altos: Add defines for 2400 and 9600 baud telemetry rates
- * altos: Add config support for 2400 and 9600 baud telemetry rates
- * altos: Call ao_telemetry_reset_interval when telemetry rate changes
- * altos/cc1111: Adjust receive parameters to improve sensitivity
- * altos/cc1111: Add 2400 and 9600 baud telemetry rate support
- * altos: Add 2400 and 9600 baud telemetry support to cc115l driver
- * altos: Packet reception tuning for cc1120 driver
- * altos: Add telemetry rate support to CC1120 driver
- * altos: Rework packet receive for cc1120
- * altoslib: Support multiple telemetry rates
- * altosuilib: Add telemetry rate to Scan UI
- * altosui: Support telemetry data rates
- * telegps: Support variable telemetry rate
- * Add support for the "kite" micropeak variant
- * Bump version to 1.4.9.1 -- on the way to 1.5
- * altosui: Hide inactive altimeter configuration entries
- * altos/telemini-v2.0: Add memory decorations to new telemetry variables
- * altos: Add smaller pa to altitude table for TeleMini
- * altos/telemini-v2.0: Enable beep config and radio rate config
- * micropeak/altosui/telegps: Fix icon file names
- * altoslib: Clean up GPS DOP support in AltosState
- * altoslib: Ensure CSV output is consistent
- * altosuilib: Add GPS DOP values to graph
- * altosuilib: Add GPS DOP values to info table
- * altosuilib: Allow for unitless axes in graphs
- * altos: Extend GPS altitudes to at least 24 bits everywhere
- * altoslib: Handle wide GPS altitude values in eeprom and telemetry
- * altos: Scale DOP values by 10 in GPS drivers
- * altos: Record pdop value in TeleMetrumV2 log
- * altos: Use 32-bits for flight state data (alt/speed/accel)
- * altosui: Fix the 'Graph' button on the landed tab
- * altoslib: Extend telemetry heights from 16 to 32 bits
- * libaltos: Bind to libbluetooth at runtime on demand
- * altosui: Don't show bluetooth UI bits on mac/windows
- * libaltos: typo in libaltos broke the build
- * telegps: Missing function in TeleGPSConfigUI
- * altos/telefire,telelco: Add HAS_RADIO_RATE to launch system software
- * ao-tools: Add TMv2 and Tgps log formats to cc.h
- * ao-tools: Provide altitude to temperature conversion function
- * ao-tools: Add a few GPS telem/eeprom constants
- * altos: Interrupt radio receive when changing data rate
- * altos: Make ao_gps_print deal with telem containing 32-bit altitude values
- * altos/test: Build TeleMetrumV2 flight test variant
- * altoslib: Parse eeprom 'altitude-32' fields
- * Set version to 1.4.9.2
- * altosuilib: Fix minor scan UI nits
- * linux-fat: Fix up fat linux install icons, mime types and .desktop files
- * altoslib: Handle TeleGPS files for KML export
- * altos: Have MicroKite just start recording at startup
- * altos: Document which TeleFire alarm pins are which
- * altos: Report additional pyro channels via beeper
- * altosdroid: Add telemetry rate support
- * altosdroid: Skip updating hidden UI elements
- * altoslib: Parse 'Log fixed:' configuration value
- * altoslib: Handle link timeout in AltosDebug.read_memory
- * altoslib: Close serial port when AltosFlash fails to detect a target
- * altoslib: Improve performance of AltosLib.hexbytes
- * altoslib: Remove some debug printfs
- * ao-tools/ao-send-telem: Support sending TM v2 and Tm v2 telemetry
- * Use -ldl when testing whether -m32 and -m64 builds work
- * cc1111: Wait for internal flash write to complete
- * telegps-v1.0: Provide one log and append to it
- * altosui: Make Windows java test "smarter"
- * altos: Add telerepeat-v1.0
- * Add ao-tools/ao-cal-accel
- * ao-bringup: Use ao-cal-accel instead of cal-accel in turnon scripts
- * ao-bringup: Test EasyMega boards
- * altos: Make sure pyro remains valid during delay
- * altosdroid: start restoring from log data on startup
- * altoslib: TeleMega telemetry pyro voltages are uint8
- * altosdroid: fixup fetching active device address
- * altosdroid: Add quit. Restart. Show freq in title.
- * altoslib: create logfiles preference object. check link in existing_data
- * altosdroid: Add missing preferences backend file
- * altosdroid: reload previous log file at connect time
- * altos: Don't add AO_LOG_FLIGHT to existing GPS logs
- * altoslib: Ignore extra AO_LOG_FLIGHT records from TeleGPS
- * altoslib: Catch a couple null pointers in AltosConfigTD
- * altosui: Fix 'pad' screen for TeleGPS
- * altos/telefire: Add firing length to manual pad command
- * altosdroid: Use single object to pass data to UI
- * altos: Allow negative values for pyro configuration data
- * altosui: Don't mark altimeter dirty when opening pyro panel
- * altosdroid: add new TelemetryState.java
- * altosdroid: Ignore TelemetryService messages after service shutdown
- * altosdroid: Update tab contents before switching
- * altosdroid: Add imperial unit support
- * altosdroid: Mark completed items as 'done'
- * altos: Reduce deviation at 2400/9600 baud
- * altoslib: Update local callsign/baud rate when using remote protocol
- * altoslib: Increase timeouts when using low baud rate remote protocol
- * altos: Scale packet master receive delay by baud rate
- * doc: Update for version 1.5 release
- * altosui: Include EasyMega firmware in fat release
- * Tag version 1.4.9.3
- * altoslib: Fix idle monitor parsing of MMA655x state
- * altos/easymega: Set USB PID for EasyMega to 0x0028
- * altoslib/altosuilib: Add EasyMega support
- * altoslib/altosuilib: clean all versions of the .jar file
- * icons: Use DESTDIR when updating mime/icon caches
- * .desktop: Use %F instead of %f in .desktop files
- * configure: Add --disable-install-shared-mime-info option
- * altoslib: Stop re-loading previous flight when starting telemetry monitoring
- * telegps: Was mis-configuring the 'Configure Device' dialog
- * altos: Fix ability to disable telemetry by setting interval to 0
- * altos: Make sure we don't beep out continuity twice in idle mode
-
- -- Bdale Garbee <bdale@gag.com> Sat, 13 Sep 2014 11:33:05 -0600
-
-altos (1.4.1-1) unstable; urgency=medium
-
- [ Keith Packard ]
- * Sign our .inf file with the comodo key. Update signing-driver
- * Fix java version detection and downloading
- * altosui: Ship TeleMetrum v2.0 firmware with AltosUI
- * Add 1.4.1 release notes
- * Add note about including Google maps API key
- * altosuilib: Mark 'Configure AltosUI' window with maps key status
-
- [ Bdale Garbee ]
- * notes updated for TeleGPS and 1.4 release learnings
- * make sure to use Google Maps API key for official builds
- * need the api key in Bdale's root too
- * releasing 1.4.1
- * update ChangeLog for release
-
- -- Bdale Garbee <bdale@gag.com> Tue, 24 Jun 2014 21:57:12 -0600
-
-altos (1.4-1) unstable; urgency=medium
-
- [ Keith Packard ]
- * Add linux installer script
- * Put altusmetrum.svg and micropeak.svg in icon directory
- * Move .desktop and icon management out of debian dir
- * micropeak: Construct linux install script
- * Mark .desktop files as executable
- * Re-create drill templates
- * doc: Need to publish .svg files as well
- * altos: Move balloon flight code to core
- * altos: Expose ao_usb_running globally
- * altos: Set reasonable accel values when !HAS_ACCEL
- * altos: Make balloon code run again
- * altos: Create balloon-specific load for TMv2 hardware
- * libaltos: Link so with -znoexecstack flag
- * Mark development sequence to 1.3.3 by bumping version to 1.3.2.1
- * altosui: Retry device enumeration after rebooting for self flash
- * Install .desktopfile as _SCRIPTS so they are left executable
- * doc: Add separate outline pdf generation
- * Add flash loader for stm-demo board
- * Re-add LCD bits to stm-demo
- * Add USB True Random Number Generator product
- * altos: Don't require projects to define PACKET_HAS_SLAVE
- * altos: fix building LPC serial support for STDIO
- * altos: Fix LPC LED driver
- * altos: Missing ao_pins files for usbtrng
- * altos: Another missing usbtrng file
- * altosui: Hide Tilt Angle values when not available
- * Add easymega firmware
- * altos: HAS_LED is useless; remove it
- * altoslib: Ignore speed/accel after boost when finding maxima
- * altoslib: Fix EasyMini voltage computations
- * Add easymini turnon script and helpers
- * altoslib: Missed a couple of easy mini voltage API changes
- * altos: Rename 'core' to 'kernel'
- * ao-bringup: Get turnon_telemini working
- * ao-tools: Use 'program' command in ao-flash-lpc instead of 'flash'
- * ao-tools: Wait for device to become ready instead of failing
- * doc: Outline files are now generated, so don't put them in git
- * altos: Report battery voltage instead of S at startup
- * Bump version to 1.3.3
- * doc: Document new voltage beeping at startup time
- * altosui: Add ignitor tab for TeleMega extra ignitors
- * ao-bringup: Split out easymini test into separate script
- * altos: Build TeleBalloon v2.0 by default
- * altos: Replace C code attiny async output with inline asm
- * altos: Provide stable binaries for MicroPeak
- * altos: Fix nanopeak compile
- * altosui: Disable flight log configuration while flights are stored
- * altos: Add 'microwater' product
- * altoslib/altosui/altosuilib/libaltos: Remove trailing whitespace
- * altosuilib: Make lines in graphs 2 units wide
- * altos: Switch beeping to farnsworth spacing
- * altosui: Add extra ignitors to graphable objects
- * altoslib: Track pyro firing state when reading mega eeprom files
- * altosui: Mark TeleMega additional pyro ignitor fired points in graphs
- * ao-telem: Dump orientation field from TeleMega sensor telemetry packet
- * ao-load: Make ao_sym static to avoid collision with ao-editaltos
- * ao-tools: Clean up ao-sym structure an initializers
- * altos: For telelco discovery packets, retry 5 times with shorter timeout
- * altos: Add configurable beep tone
- * altosui: Add configuration UI for beeper tone
- * altos: 8051 64 * 16 multiply function was broken for negative 64-bit
- * altoslib: Add a comment to remind us to fix the IMU code to deal with calibration
- * altoslib: Parse remaining mega AO_LOG_FLIGNT and AO_LOG_GPS_TIME fields
- * altosui: Add GPS course, ground speed and climb rate to graphs
- * altos: ublox driver always offers course data when it has a fix
- * altos: Fix byte offsets in the mega AO_LOG_FLIGHT packets
- * altos: Clean up trailing whitespace in ao_pad.c
- * altos: Simplify quadrature tracking
- * atosui: Hide Callsign and RSSI tabs for devices without a radio
- * ao-bringup: test-baro should accept altitudes a bit below sea level
- * ao-bringup: Use official binaries for EasyMini turnon
- * altos: Add LED test command to pca9922 driver
- * altos: Report amount of program space available in the version command
- * altos: Assume all LPC products will have 32KB of flash
- * altos/stm: Use flash address of boot loader instead of 0x0
- * altos/stm: White space fix in ao_boot_pin.c
- * altos/stm: Figure out available flash space based on chip id registers
- * altos/stm: Use #define'd constants for GPIO register addresses
- * altos/flash-loader: Check memory addresses against flash space
- * ao-tools/ao-usbload: Check image flash usage against device flash availability
- * altos/cc1111: Wait for xtal to be stable
- * altos/cc1111: Errata fix isn't needed for discontinued products
- * altos/cc1111: Add support for CPU-driven USB pullup
- * altos/cc1111: Switch P1_0 from a green LED to USB pullup
- * altos/telemini-v2.0: Remove old baro->alt conversion table
- * altos/telemini-v2.0: Enable beep frequency configuration
- * altos: Make quadrature debounce per-pin rather than per-device
- * doc: Document the Apogee Lockout setting
- * altos: Use explicit boot loader signal in ao_boot_reboot
- * altos: stm and lpc ao_boot.h were identical. move to kernel.
- * altosui: Remove debug printf about beep config
- * altosui: Remove another beep config debug printf
- * altos/stm: Make stm applications depend on ao_boot.h
- * altos/lpc: adc code computes number of active ADC channels
- * altos/lpc: whitespace
- * altos: Allow APRS to send just battery voltage
- * altos: Fix cc115l debug build
- * altos: Expose ao_gps_set_rate from u-blox driver
- * altos: Don't define ao_ignite_decivolt without igniters
- * altos/test: Get APRS generation test working again
- * altos/test: Parse mega ground data. Fix pyro parsing
- * altos: Add config values for tracker start motion limits
- * altoslib: Move CSV/KML output code to altoslib
- * altosui/altosuilib: Cleanup -Xlint:unchecked warnings
- * altosui/altosuilib/altoslib: Move more stuff out of autosui. Reduce site map memory
- * ao-tools: Add cc_usb_write function
- * altoslib/altosuilib: Change versions to altoslib:4, altosuilib:2
- * micropeak: Add -Xlint:unchecked to javac line
- * altos: Make MS5607 PROM a public variable
- * altos: Move ao_config declarations to ao_config.h
- * altos/test: Fix ADC structure for mega, use ao_config.h
- * altosuilib: Add multiple zoom levels and content types to map
- * altos: Fake flight code changes in kernel and stm
- * altosuilib: Add distance measuring line to site map.
- * altosuilib: Decompress map images asynchronously and in parallel
- * altosuilib: Add google maps API key, configured with -with-google-key
- * altoslib: When log-format is missing, use product
- * altosuilib: Remove debug printf in AltosSiteMapCache
- * altosuilib: Update map preloading UI to include zoom and maptypes
- * altosuilib: Publish AltosSiteMap.centre. Add prefetchMaps with old API
- * altosuilib: Don't try to draw to destroyed map windows
- * Document the need for ~/altusmetrumllc/google-maps-api-key
- * altosui/altosuilib: Shuffle lots more code from altosui into altosuilib
- * telegps: Add first version of telegps
- * Mark version 1.3.2.2
- * doc: Add outline of TeleGPS doc
- * telegps: Working towards building fat versions of telegps application
- * telegps: Use altosui's Instdrv NSIS plugin for telegps
- * telegps: Add device configuration dialogs
- * telegps: Add preferences dialog
- * telegps: Add scan UI
- * telegps: Hook up data download dialog
- * telegps: Add 'Info' tab
- * telegps: Don't try to ship TeleGPS firmware yet
- * telegps: Auto-connect to any base stations plugged in at startup
- * telegps: Add flash device functionality
- * telegps: Add info table
- * java: Refactor AltosFlightDisplay units and font update handling
- * telegps: Add graph display
- * Build telegps distribution bits with 'make fat'
- * telegps: Add missing TeleGPSGraphUI.java file
- * Capture windows build error messages
- * TeleGPS firmware isn't quite ready, don't include in windows fat build yet
- * telegps: Fixup windows fat build harder
- * telegps: Add config for tracker starting distances
- * altos: Switch APRS altitude encoding computation to fixed point
- * altos: Test APRS altitude encoding
- * altos: Allow sparse GPS data logging for TeleGPS
- * altos: Configuring pyro channels can use more than 48 characters
- * altos: Maximum pyro configuration parameter has 4 bytes in the name
- * altos: Fetch/store only 8 bits for pyro state values
- * altosui: Fix pyro channel value formatting
- * altosui: Display error message when parsing pyro channel values fails
- * altoslib: Add missing AltosConfigDataException file
- * telegps: Trap AltosConfigDataException in telegps config
- * doc: Create release notes for version 1.4
- * altosuilib: Let the user hand-edit the preload map radius
- * telegps: Update icon and icon building
- * altos: Add ao_distance.c to compute cartesian distances on the globe
- * altos: Add tracker task for TeleGPS
- * altos: Include sensor logging task only on flight boards
- * altos: Allow cc115l driver to be built without radio power control
- * altos: ao_distance was overflowing when checking for longitude wrap
- * altos: Change tracker not-moving speed to 2m/s and document
- * altos: Have tracker average 5 GPS samples before moving to pad mode
- * altos: Stick flight state in GPS location packets
- * altos: Fix tracker start state
- * altos: tracker distance computation flipped arguments around
- * altos: Add debug to tracker to force launch
- * altos/telegps-v0.3: Add tracker task
- * altos: Add AO_LOG_FLIGHT packet to TeleGPS logs
- * altos: Fix config to set default log size for all devices with log
- * altos/lpc: HAS_USB_CONNECT has been changed to mean a custom pin
- * altos: Force telemetry on by default for v0.3 TeleGPS boards
- * altos/telegps-v0.3: Disable APRS by default. Set log max to 1M
- * altos/telegps-v0.3: Remove ao_flight_number from main program
- * altos: Add telegps-v1.0 code and loader
- * altos: Move ao_tracker.c to kernel
- * altos: Allow AO_CONFIG_MAX_SIZE to be configured. Validate it.
- * altos: Allow value other than 0 for marking erased flights
- * altos: Clear out eeprom erase records when writing entry 0
- * altos/telemega-v1.0: Adjust config params to make flight erase work
- * altos: Add TeleGPS logging format
- * altos: Write current flight state to GPS data from GPS drivers
- * altos: Write tracker logging from tracker thread directly
- * altos: Update other CONFIG_EEPROM users to set LOG_ERASE_MARK
- * altos: Switch TeleGPS to GPS logging format
- * altoslib: All products with logging have the 'l' command
- * altoslib: Add TeleGPS log parsing code
- * altoslib: Record whether flight data includes sensor values in AltosFlightStats
- * altosuilib: Show GPS instead of (missing) flight data for TeleGPS graphs
- * altosuilib: Add GPS altitude as a possible graph value
- * altosuilib: Fix crash when initializing site map cache
- * telegps: Track graph windows as one of the TeleGPS windows
- * Set version to 1.3.2.3
- * altos: Use 0x80 to indicate valid state value in the GPS location packet
- * altos: Define lat/lon sum variables as 64-bit instead of 16
- * altos: Reduce tracker GPS buffer to 4 samples
- * altos: Make telegps builds depend on ao_tracker.h
- * ao-tools: Parse TeleGPS state value from gps location packet
- * altoslib: Parse TeleGPS state value from GPS telemetry packet
- * altos: Encode TeleGPS battery voltage in configuration packet
- * altos: Enable ADC for TeleGPS v1.0 battery voltage measuring
- * altoslib: TeleMega uses 5.6k/10k divider for v_batt
- * altoslib: Recover battery voltage from TeleGPS configuration packet
- * Bump to version 1.3.2.4
- * Revert "altoslib: Parse TeleGPS state value from GPS telemetry packet"
- * Revert "altos: Write current flight state to GPS data from GPS drivers"
- * altos: Report total available log space in version command
- * altos: Make extra pyro channel firing time configurable
- * Revert "ao-tools: Parse TeleGPS state value from gps location packet"
- * Revert adding state to GPS location packets
- * altos: Simplify tracker logic, removing boost detect
- * altos: Set TeleGPS default log size to half of avaiable memory
- * altoslib/altosui/telegps: Change log size configuration
- * altoslib/altosui/telegps: Switch TeleGPS config to motion/interval
- * altoslib: TeleGPS no longer logs satellite information
- * altoslib: Add new 'stateless' flight state for TeleGPS
- * altoslib: Check for time going backwards when replaying from file
- * altosuilib: Split battery graph enable out from other adc enables
- * altoslib: Use GPS speed/height values when other sensors are missing
- * altosui: Show "Missing" instead of huge numbers in descent/landed tabs
- * altosuilib: Skip voice announcements for invalid values
- * altosuilib: Move AltosFlightStatsTable to altosuilib
- * telegps: Add statistics tab to graph UI
- * altosuilib: Rewrite map GUI bits
- * altoslib: Use GPS seconds as an additional sort key for TeleGPS eeprom
- * altos: Disable TeleMini v2.0 build for now
- * altosuilib: Remove old widget-based map UI
- * altos/telemini-v2.0: Disable beep frequency config on TeleMini v2.0
- * altos: Re-enable telemini v2.0 builds
- * altosdroid: Altosdroid build doesn't work in parallel, so stop trying
- * altosui: Add pyro firing time configuration
- * doc: Update 1.4 release notes to include a few more changes
- * altosuilib: Handle font and units changes in maps and stats table
- * altosui: Don't list tracker parameters when configuring altimeter
- * altoslib: Report GPS height when baro height is not available
- * altosuilib: Repaint map when starting line draw
- * altos/telegps: Build .ihx versions for TeleGPS
- * telegps: Remove 'Flight' from titles
- * doc: Update altusmetrum docs and screen shots for 1.4
- * doc: Add TeleGPS screenshots
- * altosui/telegps: Reduce CPU time needed for flight displays
- * telegps: Don't re-add frequency menu when already present.
- * altos/telegps: Don't log data when plugged in to USB
- * debian: Fix build depends icotool -> icoutils
- * altos: Show current flight number for TeleGPS
- * altos/telegps: Set default log to 496kB for 4 logs
- * altos/telegps: Keep ring of recent GPS positions to detect motion quickly
- * altos: Define ao_log_mutex in ao_log.c rather than every log product
- * altos/telegps: Create new flight if current flight is erased
- * altoslib: Call state.set_serial first for telemetry parsing
- * altoslib: Remove telem monitoring when closing log file
- * telegps: Disconnect telemetry device when closing monitor window
- * telegps: Show flight number in monitor window
- * altosuilib: Build some common classes for displaying values in flight window
- * altoslib: Add conversion class for voltages
- * altoslib: Correctly save firmware version in AltosState
- * telegps: Add status tab
- * altosdroid: Don't crash when the map is touched
- * altosdroid: Improve voice for TeleGPS
- * telegps: Shuffle menu entries around
- * altosuilib: Make map-cache per-window instead of global
- * doc: Add a bunch more stuff to the telegps docs
- * telegps: Allow TeleGPS preferences to have a custom title and label
- * doc: TeleGPS docs are complete
- * altoslib: Add units converters for latitude and longitude
- * altoslib: When GPS disappears, set range and elevation to MISSING
- * altosuilib: Require all flight display classes to provide a name
- * altosuilib: In graph, show zero sats in view as 0 instead of MISSING
- * altosuilib: provide getName() for AltosInfoTable
- * altosuilib: Make sure only one thread is closing serial device
- * altosuilib: Add more options to AltosUIIndicator to suit AltosUI
- * altosuilib: Add AltosUIFlightTab class
- * altosui/telegps: Switch to AltosUIIndicator and AltosUIFlightTab
- * alotsuilib: Remove old "mega" and "mini" file extensions from data chooser
- * micropeak: Make statistics entries un-editable
- * telegps: Fix Mac icon file name
- * altosuilib: Make graph enable buttons be CheckBoxes instead of RadioButtons
- * icon: Create all icons from .svg files
- * icon: Build windows ico files, clean built files
- * altosui: Build MacOSX icon from svg
- * icon: Build resolutions needed for Java bits too
- * telegps/micropeak: Ship built Mac OSX icons
- * debian: Build requires /usr/bin/convert now
- * icon: Make the icon shadows a bit less harsh
- * altosuilib: Serialize access to async tile notify function in preload
- * altoslib: AltosFlightStatsTable: another editable text field that shouldn't be
- * altosuilib: Remove some debugging printfs
- * telegps: Include telegps firmware in windows package
- * windows: Rename telemetrum.inf to altusmetrum.inf
- * telegps: Deal with 64-bit windows differently on install
- * altosui: Deal with 64-bit windows
- * icon: Add drop-shadows to the SVG files; stop generating in the png versions
- * windows: Sign altusmetrum.inf with altusmetrum.cat
- * altosui: Ship telegps firmware
- * Add notes about windows driver signing in the 'signing-driver' file
- * micropeak: Deal with 64-bit windows
-
- [ Bdale Garbee ]
- * have the cal-freq script save cal values to a file
- * use svg in the .desktop file
- * update copyright year assertion in MicroPeak manual, remember during releases
- * deliver images used in MicroPeak manual to web server, too
- * typo fixes from Matt Kraai
- * update turnon scripts to store cal values
- * ugly hack (just make sleep longer) to work around ttyACM* discovery issue
- * first cut of usbrelay-v0.1 support .. LEDs wiggle, not switching relay yet
- * relay control implemented, this project is now complete
- * fix copyright year
- * update TeleMega turn-on script and Releasing for new stable firmware home
- * lose the (old) easymega-v1.0 directory in favor of my fresher 0.1
- * working?
- * include EasyMega Makefiles
- * document mounting hole size for TeleGPS
- * update Releasing document to include TeleGPS firmware files in those copied
- * tweaks
- * add release to revision history
- * tagging 1.4 release
- * turn-on support for TeleGPS
-
- [ Tom Marble ]
- * add jenkins.sh
- * fix for jenkins.sh
- * jenkins.sh: make -j 4 can fail, fix for altosui-test
-
- -- Bdale Garbee <bdale@gag.com> Sun, 15 Jun 2014 17:51:01 -0600
-
-altos (1.3.2-1) unstable; urgency=medium
-
- [ Bdale Garbee ]
- * update notes on how to release
- * use firmware in /usr/share/altos for teledongle, update telemetrum for v2.0
- * updating changelog for release
-
- [ Keith Packard ]
- * altoslib: Validate TeleMega GPS_SAT log packet nsat
- * altos: Tmega Don't try to log info about more than 12 GPS sats
- * doc: Add 1.3.2 release notes
- * Set version to 1.3.2 in preparation for release
- * doc: Document flight computer wiring connections
- * doc: Fix spelling of decelerate
- * altoslib: Track GPS altitude values to be able to report max gps height
- * altosui: Show GPS max height in flight stats window of graph
- * altoslib: Don't lose gps_height value between GPS samples
- * doc: Add explicit paragraph about using one battery with Tmega
- * altosui: Use letter names for pyro channels in pyro config UI
- * doc: Update screen capture of pyro config with correct names
- * doc: Replace screen captures with 'active' window ones
- * doc: Mention that an APRS interval of 0 disables it entirely
- * altoslib: Use existing unicode Charset in AltosLink
- * micropeak: Watch serial data during download
- * altos: report 0/0/0 for APRS position when GPS is not locked
- * micropeak: Keep reading until we get valid data
- * micropeak: Missing a couple of new exceptions when loading files
- * doc: Micropeak doc updates for 1.3.2
- * doc: Update micropeak docs to include lots of pictures
- * doc: Document GPS max height addition
- * doc: Ignore generate template XSL file
- * doc: Add title page image to altusmetrum.pdf
- * altos: Add names when reporting STM ADC values
- * altos: Add watchdog timer task
- * altos: Eliminate warnings in FAT code
- * altos: Enable system timer in flash loader and prod watchdog with it
- * altos/stm: Block interrupts while reprogramming flash
- * altos: Don't write more than 12 sat infos in ublox driver
- * altos: Report nsat in view in APRS packet
- * altos: Add needed math sources to TeleGPS v0.1 build
- * altos: Fixup named ADC printing
- * altos: Re-send previous GPS position in APRS if lock is lost
- * altos: Put locked/unlocked GPS status in APRS comments
- * doc: Add remaining configurable parameters to the System Operation chapter
- * doc: Update the 1.3.2 release notes to include APRS and Fire Igniter changes
-
- -- Bdale Garbee <bdale@gag.com> Thu, 13 Feb 2014 21:56:46 -0700
-
-altos (1.3.1-1) unstable; urgency=medium
-
- [ Bdale Garbee ]
- * updated notes from 1.3 release
- * use firmware in /usr/share/altos for production flashing
- * set version to 1.3.0.2 for test flights this weekend
- * set version to 1.3.1 for release
- * update copyright date on main documentation file
- * freshen ChangeLog for release
-
- [ Mike Beattie ]
- * altosdroid: force older jarsigner signing algorithm for java 1.7
- * altosdroid: update to latest google play services
- * altosdroid: improve build system dependencies
-
- [ Keith Packard ]
- * altoslib: Convert IMU and Mag sensor values to useful units
- * altoslib: Fetch 'orient' value from Mega Sensor packet
- * altosuilib: Rearrange graph enable buttons
- * altosui: Add imu and mag sensor values to plots
- * altoslib: Bump library version
- * altos: Execute self-test on MMA655X part
- * altos: 3-axis accel calibration was invalid in explicit accel cal mode
- * altos: Complain about sensor self-test errors only in idle mode
- * altos: mma655x also needs ao_sensor_errors
- * altos: Clean up some minor warnings from -Wall
- * altos: Turn on -Wall for stm compiles
- * altos: Clean up -Wextra warnings
- * altos: unsigned value in ao_pyro_set checked for negative value
- * altos: Add default button return value from ao_button_get
- * altos/stm: Turn on -Wextra
- * altos: Clean up warnings for LPC products
- * altos: cc115l driver tone_run wasn't recording number of tones
- * altos: lpc exti setup was incorrectly testing mode
- * altos/lpc: Missing */ in definition of PIO0_4
- * altos: Turn on warnings for LPC products too
- * altos: Turn on -Werror for STM and LPC builds
- * altosui: Switch from radio buttons to check boxes in pyro config. Add close
- * altosui: Extend Fire Igniter to additional channels
- * altoslib: Add AltosOrient class and max_orient()
- * altosui: Add orient to ascent and info table views
- * altosui: Adjust info table column width
- * altosui: Switch Graph to AltosOrient type
- * altos: Add 'O' command for TeleMega orient testing
- * altos: Flip acceleration data consistently for orientation changes
- * altosui: Handle a missing libaltos when starting up
- * Bump version to 1.3.9.1
- * libaltos: Build -m64 and -m32 for fat tarball when possible
- * altosui: Require both libaltos32 and libaltos64 for fat Linux tarball
- * doc: Ship telemini outline as pdf file too
- * altos: Switch APRS to compressed position format
- * altos: Use factory calibration for all acceleration computations
- * altos: Report battery, apogee and main voltages over APRS
- * Ignore 32 and 64 bit cjnitest apps
- * altos: Add missing ADC divider values for Tmega v1.0
- * altosui: Make romconfig serial and radio cal fields 8 digits wide
- * altoslib: Fetch target device config for Fire Igniter npyro value
- * altosuilib: Remove some spurious debug printfs
- * altosui: Handle already-opened link in IgniteUI
- * altosui: Handle serial-port startup errors in idle-monitor
- * doc: Fix image widths to make them all scale the same amount
- * doc: Update for 1.3.1
-
- [ Anthony Towns ]
- * AltosSiteMapPreload: only load 49 maps
- * altosui: --fetchmaps gets same number of maps as GUI
- * altosui: rate limit map downloads
-
- -- Bdale Garbee <bdale@gag.com> Wed, 22 Jan 2014 20:56:31 -0700
-
-altos (1.3-1) unstable; urgency=low
-
- [ Keith Packard ]
- * altos: Add flash-loader for telescience-v0.2
- * altos: Add 'g' command to ublox GPS code.
- * altos: Give u-blox 3 seconds after boot before we bug it
- * altos: gps serial routines are called ao_gps_*, not ao_ublox_*
- * altos: Fix telemega v0.3 igniter order (drogue/main moved). Label ADC dump
- * altos: Initialize MPU6000 CS pin for SPI mode
- * altos: Grab SPI mutex until MPU6000 I2C mode is disabled
- * altos: Remove some MMA655x debugging printfs
- * altos: Move MS5607 info from 'v' to 'c s'
- * altos: Generate unmodulated carrier for CC1120 test mode
- * altos/cc1111: Hack on USB driver to make Windows happy
- * libaltos: Build the linux library targets when doing a 'fat' build
- * libaltos: use PurgeComm in Windows altos_close to abort in-progress ops
- * lpc: Initial lpcxpresso bits
- * lpcxpresso: Add ao_demo.c
- * altos/lpc: Get 100Hz timer running
- * altos/lpc: Get USART running
- * altos/lpc: Take advantage of USART TX fifo
- * altos/lpc: Start adding USB register definitions
- * altos/lpc: Start adding USB register defines
- * altos: Finish off LPC USB register definitions
- * altos: Allow target-specific USB endpoint specifications
- * altos/lpc: Get USB working
- * altos: Move ao_data.c from stm to core
- * altos: Allow architecture to define the type of port registers
- * altos: ao_data_get is in ao_data.c now, not ao_adc.c
- * altos: Check for packet mode before trying to disable it in flight code
- * altos: Use ao_data_pres macro in ao_log_tiny
- * altos: Use ao_port_t in m25 driver
- * altos: Add LPC spi driver
- * altos: LPC interrupt priorities are just 0-3
- * altos/lpc: Fix ao_enable_input, add ao_enable_analog
- * altos/lpc: Clean up broken IOCONF defines
- * altos/lpc: add gpio int, spi, adc and ct32b defines to lpc.h
- * altos/lpc: Add ADC driver
- * altos/lpc: Add beep driver
- * altos/lpc: Add pin interrupt driver
- * altos/lpc: Try a smaller stack.
- * altos/lpc: Use separate interrupt stack
- * altos: Add easymini-v0.1 product
- * altos/lpc: Stick USB control structure in USB memory
- * altos: Initialize SPI for easymini
- * altos: Build easymini-v0.1
- * altos: ignore built files in easymini-v0.1
- * altos/attiny: Fix ao_spi_get_bit/ao_spi_put_bit macros
- * altos: Use ao_spi_get/put_bit in MS5607 driver
- * altos/lpc: Make EXTI code work.
- * altos: Add EXTI_PIN_NOCONFIGURE to exti interface, use for MS5607
- * altos/lpc: Don't use loader to place USB endpoint data in USB ram
- * altos/lpc: Pull ADC data from the correct registers
- * altos/lpc: SPI runs off main clock (48MHz), not sysclk (24MHz)
- * altos/lpc: Missing parens around ao_gpio_set macro
- * altos/lpc: Fix beeper driver
- * altos/lpc: Create TX/RX busy macros for SPI driver
- * altos/lpc: Leave SPI enabled all the time
- * altos/lpc: Allow for alternate SPI SCLK0 pin usage
- * altos/lpc: Configuring wrong pin for SPI1 MOSI
- * altos/lpc: Reset SPI device at startup time
- * altos/lpc: Force idle mode if USB gets an address during boot time
- * altos/easymini: Easymini doesn't have USB connect or VBUS wiring
- * altos/easymini: MS5607 chip select bits were defined wrong
- * altos/easymini: Use different pins for igniter outputs
- * altos/easymini: Initialize beep and ADC. Declare use of igniter bits.
- * altos/telemega: The last two igniters are apogee and main
- * Add Mini logging format. Use in EasyMini
- * altosui: Add TeleBT firmware to release
- * altos: Set the path for the STM32L compiler explicitly
- * Bump master version to 1.2.9 to avoid confusion with 1.2 releases
- * altos: Can't use inline functions because SDCC doesn't do that
- * Separate out cortex-m0 compiler tests in configure
- * Create release notes for 1.2.1
- * doc: Update description of graph window to note new tabs (config and map)
- * altosui: Stop downloading mega eeprom on empty block
- * altosui: Missing 'break' after selecting 'mega' format detection
- * ao-tools: Add ao-mega tool to parse TeleMega eeprom files
- * ao-tools/ao-mega: Dump 'pyro' state from mega log
- * altos: Add pyro code testing to ao_flight_test for TeleMega
- * altos,altosui: Add pyro state logging for TeleMega
- * altos: Light pyro charges simultaneously if so configured
- * altos: write pyro fired to correct log field
- * altos: Make manual pyro firing command work again
- * Set version to 1.2.9.1
- * altos: Add pyro operations to regular ignite commands
- * altos: Add driver for 74hc165 shift register
- * altos: Add telefire v0.2 support
- * altos/telefire: Leave siren on all the time. Add siren/strobe debugging.
- * altos: Add debounce helper. Use in button and quadrature drivers for TeleLCO
- * altos: Add fast-timer API. Use for quadrature and button drivers
- * altos/telelco: Add 30ms delay in search after finding a box
- * altosui: Use preferred units for main deployment height configuration
- * altos/lpc: Make ADC inputs work
- * altos/lpc: Filter ADC inputs
- * altos/lpc: Turn off more clocks, disable USART for easymini
- * altos/lpc: Don't disable all of the clocks just yet, USB doesn't work
- * altos/lpc: Remove spurious semicolon
- * altos: Declare m25 write-in-progress as 'ao_port_t'
- * altos: Disable USB on all flight computers when in flight mode
- * altos/lpc: Get the IRC turned off after boot time
- * altosui: Add raw pressure to the AltosUI graph
- * altos/lpc: Get rid of ADC filter
- * altos/cc1111: Fetch RSSI for TeleFire from correct byte
- * altos: PCA9922 LED driver needs Enable driven low to latch values
- * altos/telefire: Radio status (no data, weak data, good data) on LEDs
- * altos/lpc: Enable brown-out-detector
- * altos/lpc: Remove ao_usb_task structure
- * altos/lpc: Don't disable all interrupts when disabling one interrupt
- * altos/telefire-v0.1: Use same LED selection as the v0.2 setup
- * altos/lpc: Add boot loader
- * altosui: Add EasyMini USB ids
- * altos: Support mega-style logging without ADC
- * altosdroid: Just use GPS location provider to build on 4.2
- * micropeak: Add Download button to menu bar
- * altos/lpc: Rename serial port to 'serial0'
- * altos: Remove ao_radio_gpio_bits from normal build
- * altos: Make FAT test program link explicitly against libcrypto
- * altosui: AltosDbm class was missing somehow
- * altosdroid: Add note to report TeleBT battery level
- * altos: allow projects to override default config values
- * altos: Allow ublox to run at other baud rates
- * altos: Set default LPC stack to 512 bytes, Em to 384 bytes
- * altos: Wake up on LPC usart ISR only once
- * altos: various cc115l driver hacks
- * altos: Add telegps v0.3 product
- * altos: Allow products to disable RDF entirely
- * altos/lpc: Stop using burst mode for LPC ADC
- * altos: Use installed arm compiler for LPC
- * altosdroid: Add note to report TeleBT battery level
- * altos: Set default LPC stack to 512 bytes, Em to 384 bytes
- * altos: Wake up on LPC usart ISR only once
- * altos: MS5607 pressure computation for low temperatures was wrong
- * altos: Explicitly list the linker script needed for AVR targets.
- * Initial TeleMini bits
- * altos: Add 64-bit add/mul/shift for SDCC
- * altos: Make 64x16 mul a bit faster
- * altos: Add 64x64 multiply. Test 64 ops for dest same as either source
- * altos: Add 64-bit subtraction
- * altos: Make TeleMini v2.0 fit
- * altos: Add exti and spi to telemini-v2.0
- * altos/teletiny-v2.0: Support multiple SPI busses on CC1111
- * Bump version to 1.2.9.2
- * altos: Changes required by cc1111 multi-spi support
- * altos: Build more products by default
- * ao-tools: Use TeleDongle for default ao-dbg target
- * cc1111: Rework ADC configuration a bit, fix Tm V2 ADC usage
- * cc1111: Hacky pin interrupt support. Only useful for TeleMini v2
- * altos: Get telemini to copy current MS5607 state to ring.
- * altos/cc1111: Leave pin interrupts completely disabled at init time
- * altos/cc1111: Wake up non-ADC sensor code each timer tick
- * altos: Use %ld and %lu for MS5607 debug output
- * altos/telemini-v2.0: Add ao_exti.h depend. Init beeper and usb.
- * altos: Check for MS5607 MISO low before sleeping
- * altos: Make ao_wakeup reentrant
- * altos: Don't use ao_data on cc1111 projects
- * altos: Initial TeleMetrum v2.0 bits
- * altos: Add TeleMetrum v2.0 boot loader
- * altos: Rename TeleMetrum v2.0 ADC sense members
- * altos/telemetrum-v2.0: Fix MMA6555 SPI pin assignment
- * altos/telemetrum-v2.0: Use 9600 baud for ublox
- * altos: TM v2 places the MMA6555 upside down compared to Tmega
- * altos: Update time for next alarm each time a task is added
- * altos: Add debugging to ublox GPS driver
- * altos: Force u-blox to 9600 baud for now
- * altos/stm: New compiler doesn't correctly build flash bits yet
- * altos/stm: Make sampling profiler work again
- * altos/stm: Remove stale timer defines
- * altos/stm: Make sure we switch to MSI during timer init
- * altoslib: Start restructuring AltosState harder
- * altos: Split EasyMini and TeleMini log formats
- * altoslib, altosui: Restructured state management now does TM eeprom files
- * altoslib/altosui: Get legacy telem working with new AltosState structure
- * altoslib/altosui: Fixes for state changes
- * altos/lpc: Add bits for building flash loaders
- * altos/telegps: Initialize logging system
- * altoslib/altosui: Further AltosState transition work
- * altos: Not all products have pins to control flash loader
- * altoslib: More AltosState hacking
- * altoslib: Ensure eeprom file body always exists
- * altoslib: Correct tick wrapping in eeprom file reading
- * altoslib: Correct mega/metrum eeprom years by adding 2000
- * altoslib: Clean up metrum eeprom file reading
- * altoslib: Remove duplicate cmd/tick from TM eeprom file code
- * altoslib: Make Ascent/descent use different filter values. Always filter.
- * altoslib: Use first few baro samples for ground pressure on TM
- * altoslib: Start integrated value at 0 by default
- * altoslib: Clear sat data when tick changes
- * altoslib: Set measured acceleration for measured acceleration
- * altoslib: Finish AltosState changes. Update version number.
- * altoslib: Remove AltosRecord-based telemetry code
- * altoslib: remove AltosRecord based eeprom code
- * altoslib: Remove more AltosRecord based files
- * altoslib: Use AltosTelemetry.parse to pull telem lines apart
- * altoslib: Only open log file when both flight and serial are known
- * altoslib: Update received time when replaying flights
- * altoslib: Record time_change in AltosState correctly
- * altoslib: Rewrite AltosTelemetryIterable
- * altoslib: Remove debug printf from AltosTelemetryMetrumSensor
- * altosui: Fix 'Graph Flight' button in landed dialog
- * ao-tools/ao-telem: Parse new TM v2 packets
- * altos: Set tick value in new TeleMetrum v2 sensor packets
- * altosui: Remove debugging printf from InfoTable
- * altoslib/altosui: Add TeleMini-v1.0 eeprom support
- * altoslib: Set 'valid' for valid TeleMetrum eeprom download
- * altoslib: Lock access to AltosLink config_data
- * altoslib: Add TeleMini eeprom file to Makefile.am
- * altosui: Load Telem files in AltosDataChooser too
- * altosui: Set 'flight' value in AltosEepromMonitor window during download
- * altoslib: Add receiver serial to telem file names
- * altoslib: TeleMetrum v2 telemetry includes computes Pa/°C, not raw values
- * altosui: Include device name in Table view
- * altos: Move micropeak sources around
- * altos: Add nanopeak-v0.1
- * altos: Stop copying cc1111 binaries to the altos/src dir
- * altos/telemini-v2.0: Change initialization order
- * altos/telemetrum-v2.0: Use red LED during boot time
- * altoslib: Prefer averaged ground pres for ground alt computation
- * Add TeleMini v2.0 telemetry support
- * altos: Set TeleMini v2.0 USB ID correctly
- * Change differentiation filter constants and limits
- * altos: Don't require an LED for ao_flight
- * altos/lpc, altos/stm: ARM requires ISB after switching stack pointers
- * altos: Rename easymini-v0.1 to easymini-v1.0
- * altos/stm: New GAS version requires flags in APSR assignment
- * Add --with parameters to configure for compiler selection
- * altos: Broken test for M0 compiler in src/Makefile
- * altos: avr-gcc appears to find the loader scripts without help now
- * altosui: Binaries to package are only in per-product dirs now
- * altos: Messed up the ifeq syntax a bit so ARM bits weren't getting built
- * doc: Add EasyMini outline drawing
- * doc: Add easymini outline to distribution
- * Bump version to 1.2.9.3
- * altos: Use installed pdclib
- * altos: Fix stm-bringup demo build to use installed pdclib
- * Make sure the AVR compiler can actually link stuff
- * Another try at skipping broken avr-gcc
- * altos/micropeak: Increase boost detect to 30m
- * altoslib,altosui: Be more robust when graphing bogus .telem files
- * altos: Use #define values for ublox packet types
- * altos: Merge GPS logging into a single function
- * altos: Add floating point math functions from newlib
- * altos: Fix GPS test frameworks to handle shared ao_gps_new variable
- * altos: Add gyro-based orientation tracking
- * altos: Calibrate IMU accelerometers too
- * altos: IMU accel calibration values need to be signed
- * altos: Mark arguments to quaternion functions as const
- * altos: Add some comments describing quaternion multiplication
- * altos: Add functions to init quaternions from vector pairs and euler angles
- * altos: Rename ao_orient to ao_sample_orient
- * altos: Keep 9 more bits of average pad IMU gyro data
- * altos: Add sinf to math code
- * altos: Fixup for ao_sample_orient rename
- * altos: Compute initial rotation from vertical
- * altos: Correct incremental rotation computation
- * altos: Fixup for 32-bit gyro averages
- * altos: Change ao_mpu6000_gyro arg to float
- * altos: Update quaternion tests to check vectors_to_rotation
- * altos: Add orientation test when HAS_FLIGHT_DEBUG is set
- * altos: Make telemega v0.1 compile with new quaternion code
- * altos: Make telemega v0.3 compile with new quaternion code
- * altos: sample profile address range was too narrow
- * altos: Don't hold GPS mutex while waiting for GPS data in report code
- * altos: Add orientation tracking to ao_flight_test
- * altoslib: Raise ParseException on invalid eeprom format
- * altoslib: Start moving eeprom download logic to altoslib
- * altosui: Make AltosEepromDownload not swing-dependent
- * altosui, altoslib: Move eeprom download code to altoslib
- * Ignore mac .dmg files
- * Add ublox checksum generating program
- * altos: Clean up .gitignore and add a few random files
- * ao-tools: add ao-mega man page, ignore executable
- * Add TeleMini v2.0 turnon script
- * ignore "compile" script
- * altos: Build TM v2.0 firmware by default
- * altos: Don't hold GPS mutex while waiting in TM v2.0 report
- * altos: Allow use of internal EEPROM for config storage
- * altos: Move TeleMetrum v2.0 to using internal eeprom for config
- * altos: Move telemega to using internal eeprom for config
- * altos: Make sure flight erase log comes after config blog
- * altos: include ao_eeprom.h in ao_telemetrum.c to define ao_eeprom_init
- * Bump to version 1.2.9.4
- * doc: Start work on 1.3 doc updates
- * doc: Get altusmetrum.xsl to validate
- * doc: Switch to xorg style to generate index
- * doc: Make altos.xsl validate
- * doc: Make telemetry.xsl validate
- * Make companion.xsl validate
- * doc: Make micropeak.xsl validate
- * doc: Make pdf files depend on local stylesheet
- * doc: Use system fo docbool.xsl instead of network one
- * debian: Build now depends on 'xmlto' for docs
- * Extend the hardware overview chapter. Edit System Operations
- * Remove duplicate log description. Describe pyro config.
- * Use more 1/4 single characters
- * doc: "rocketry electronics" instead of listing products
- * doc: use correct quotes in altusmetrum.xsl
- * doc: Add telemetry enable and APRS interval config docs
- * altosui: Handle units in pyro config.
- * doc: Work on AltosUI Pyro config docs a bit more.
- * ao-tools: Create general elf and hex library routines
- * ao-tools: Add debug printf support
- * ao-tools: Add ao-elftohex and .ihx symbol support
- * ao-tools: Move ao-selfload into library
- * ao-tools: move 16/32-bit readers from ao-stmload to lib
- * ao-tools: Missing ao-selfload.h
- * ao-tools: Split out altos symbol editing from ao-stmload
- * ao-tools: Split out USB loader to ao-usbload
- * doc: First pass for 1.3 finished; docs have most major sections updated.
- * src/cc1111: Turn off RC osc after xtal is running
- * altos: Add lots more GPS data to mega log
- * altos: Telemega uses eeprom, include it in main file
- * altos/test: Compute and plot tilt based on GPS track
- * altos: Nothing in altos uses AES decryption, so don't compile it
- * altosui: Don't try to report bearing/elevation without GPS
- * altosui: Clean up serial close handling
- * altosuilib: Deal with AltosUnits API change
- * ao-tools: Add ao-flash-stm and ao-flash-lpc scripts
- * ao-tools: Allow building without stlink and readline
- * ao-tools: Clean up ao-stmload and ao-usbload options. Add --raw
- * altos: Allow products to override default 100mA USB current
- * altos: Build .ihx files for all arm projects
- * altos: Change flash loader name to just AltosFlash
- * altos: remove all versions of stm-demo executable
- * altoslib: AltosEepromMonitor had false import of altosuilib
- * ao-tools: build ao-usbload by default
- * altos/stm: arm-none-eabi-binutils now puts 'main' into .text.startup
- * altoslib: Support binary reading/writing in AltosLink
- * altoslib: Add symbols to .ihx files
- * altoslib: Create AltosProgrammer class
- * altoslib: Publish mapping from product name back to USB id
- * altosuilib: Don't match product_altusmetrum for product_basestation or product_altimeter
- * altoslib: Use symbols in AltosRomconfig instead of fixed offsets
- * altoslib: Add AltosNoSymbol exception
- * altoslib: Add self-flashing code
- * Add new tools to .gitignore
- * altoslib: Don't require radio_cal or usb_descriptors in AltosRomconfig
- * altosui: Match directories in hex file matcher
- * altosui: When flashing to TeleDongle or TeleBT, match any .ihx file
- * altos: Oops. Was only filling out part of the TeleMetrum ADC record
- * altos: Rename telemega-v0.3 to telemega-v1.0
- * ao-bringup: Add turnon_telemega script
- * altosui: Ship TeleMega-v1.0 firmware
- * debian: .ihx and .map files are left in subdirs now
- * doc: More altusmetrum.xsl updates for 1.3
- * Set version to 1.3 in preparation for release
- * altos: Remove ARM .ihx files on 'make clean'
- * java: Add -target 1.6 to all java compiles
- * java: Missed libaltos java compile flags from previous patch
- * ao-tools: Use st-flash for STM flashing instead of openocd
- * Clean up reflashing section, include section on self-flash recovery
- * doc: Convert several more itemizedlists to variablelists
- * Keep tables together on a page
- * doc: Add product pictures to manual
- * Add altosui image and attempt to add launch photo to title
- * doc: Add screen shots everywhere
- * altos: Broke TeleMetrum GPS reporting by holding the GPS mutex too much
- * doc: Publish images with HTML bits
- * altosui: Add EasyMini bits to fat distribution images. Update telemetrum.inf
- * altos: Use all 16 bits of setup packet len when limiting reply len
- * altos: Make TeleMega v0.1 work more like TeleMega v1.0
- * altoslib: Pass InterruptedException up the stack instead of hiding it
- * altos/lpc: Be a bit more resistant to toolchain section name changes
- * altosui: Hide non-applicable altimeter config values
- * include pdclib in wrong place
- * altos: Build pdclib locally if necessary
- * altos: create target pdclib directories before building
- * altos/stm: Update pdclib paths for flash-loader builds
- * Remove stale stm test apps from regular build
- * altos: get stm-bringup building again
- * ao-tools: complain if st-flash is not available
- * Ignore .dll files in libaltos
- * Use git: path for pdclib
- * fix git: path for pdclib
- * altosui: Add docs to Mac OS X dmg distribution
- * libaltos: fix test harness main type
- * libaltos: remove usb id filtering from darwin code
- * libaltos: Import newly build libaltos.dylib
- * altoslib: Don't close telemetry reader at startup unless something fails
- * altoslib: create eeprom download thread before telling monitor about it
- * altoslib: Define 3.8 as a good battery and 3.5 as a good igniter
- * altosdroid: Use altoslib standard voltages to control lights
- * altosui: Remove some debug printfs
- * Move pdclib build results to pdclib-root
- * micropeak: Compile for java 6
- * doc: Update micropeak quick start guide to note new boost detect
- * doc: typo in micropeak doc hole->hold
- * altos/stm: Semantic error in STM usb disable caused it to not work
- * doc: Add tables describing AltOS beeps and flashes
- * altos: Try IMU self-test 10 times before giving up
- * ao-tools: Add man pages for ao-flash utilities
- * micropeak: Add micropeak man page
- * altoslib: Remove some old debug printfs for self flashing
- * altos/lpc: Reset less of the device on USB reset.
- * altos/lpc: Stop sending SETUP IN when the requested size is reached
- * altosui: When device has no valid romconfig, set RF cal to 0
- * altosdroid: bump versionName to 1.3 and versionCode to 4
- * altosui: Ship EasyMini firmware too
-
- [ Bdale Garbee ]
- * add a note about callsign matching and case sensitivity to the manual
- * new toolchain for STM32L is in /usr/bin, not /opt/cortex/bin
- * updated turn-on script for telebt 1.1
- * temporarily force stlink location in debian/rules to allow complete build
- * add serial number to ao-usbload call, pass SERIAL to cal-freq
- * capture my changes so far
- * further documentation tweaks
- * need to include the Cortex toolchain
- * a fresher changelog entry for test builds
- * we're using packaged and local-to-our-tree ARM toolchain now
- * update release docs to include option for submodules
- * update Debian standards version we claim compliance with
- * update ChangeLog from git
- * update changelog for Debian build
- * patches no longer needed
- * fix missed merge conflict
- * fix missing newline at end of src/test/Makefile
-
- [ Mike Beattie ]
- * altosdroid: update to support new state code
- * altosdroid: more updates for new AltosState
- * altosdroid: convert rogue files to unix line endings
-
- -- Bdale Garbee <bdale@gag.com> Thu, 19 Dec 2013 02:07:40 -0700
-
-altos (1.2.1-3) unstable; urgency=low
-
- [ Keith Packard ]
- * altos: Make FAT test program link explicitly against libcrypto
-
- -- Bdale Garbee <bdale@gag.com> Sat, 17 Aug 2013 16:07:25 +0200
-
-altos (1.2.1-2) unstable; urgency=low
-
- [ Keith Packard ]
- * altosui: Add TeleBT firmware to release
-
- -- Bdale Garbee <bdale@gag.com> Tue, 21 May 2013 12:53:15 -0600
-
-altos (1.2.1-1) unstable; urgency=low
-
- [ Mike Beattie ]
- * altosui: remove un-used imports
- * altosui: comment out un-used fields and methods
- * altosui: comment out un-used classes and associated imports
- * altosui: remove redundant catches
- * altosui: access class variables by class, not instance
- * altosui: comment out/remove dead code
- * altosui: add type to … implements Comparable.
- * altosui: comment out obsolete code - could probably remove the file.
- * altoslib/altosui: begin moving preferences "backend" into interface
- * altosui: add missing methods for Backend, fix BT code.
- * altosui/altoslib: add methods to interface, fix imports/exceptions in BT code
- * altoslib: Add AltosPreferencesBackend.java to Makefile.am
- * altosui/altoslib: Add call to …Preferences.init() with backend object, remove static init()
- * altosui/altoslib: bug fixes, update Makefile.am
- * altosui: add missing try/catch
- * altosui: Add return to try/catch.. duh
- * altosui: revert AltosUIPreferences init() method
- * altosui: remove un-used import
- * altosdroid: implement AltosPreferencesBackend, and initialize.
- * altosdroid: Update Makefile.am
- * altosdroid: simplify keys() method
- * altosdroid: cosmetic re-order of methods
- * altos{lib,ui,droid}: move OS specific code out of altoslib
- * altoslib: make parts of AltosLog public for usage outside altoslib.
- * altosdroid: initial implementation of telemetry logging.
- * altosdroid: add autogenerated BuildInfo.java
- * altosdroid: match only the current version tag
- * altosdroid: Add branch to BuildInfo
- * altosdroid: Add version information to UI
- * altosdroid: more reliable branch detection
- * altosdroid: more restrictive commit no. matching
- * altosdroid: initial release to Play Store
- * all: clean up .gitignore files and Makefile clean targets
- * altosdroid: excise old code/xml
- * altosdroid: update copyrights/licensing
- * altosdroid: minor whitespace cleanup
- * altosdroid: Fix up some formatting in manifest
- * altosdroid: Only update BuildInfo.java when other source files change
- * altosdroid: use a glob for source files
- * altosdroid: adjust Makefile rules
- * altosdroid: Adjust build system for GMaps & Tabs support
- * altosdroid: Symlink red/green/gray LEDs via build system
- * altosdroid: adjust release Makefile target
- * altosdroid: convert spaces to tabs in strings.xml
- * altosdroid: make AltosDroid.pos() static
- * altosdroid: whitespace cleanup
- * altosdroid: Import initial versions of XML and Java for Tab content
- * altosdroid: implement tabs interface
- * altosdroid: implement UI updating on tabs
- * altosdroid: implement Age field updating
- * altosdroid: Auto tab changing
- * altosdroid: fix side-to-side scrolling in map tab
- * ao-tools: Add ao-edit-telem to .gitignore
- * altosdroid: adjust clean targets to get rid of automake warning
- * altosdroid: Add SDK checks to configure.ac
- * altosdroid: programmatically create map fragment
- * altosdroid: Add rocket and pad map markers
- * altosdroid: Add map polyline between pad and rocket
- * altosdroid: whitespace and import tidyup
- * altosdroid: incorrect property syntax in pad xml
- * altosdroid: Add filters for TeleBT bluetooth devices.
- * altosdroid: set tab height based on screen density.
- * altosdroid: check for mAltosVoice being null.
- * altosdroid: fix up 'send last' code.
- * altosdroid: Make the service class implement locationlistener
- * altosdroid: Release v1.2, push to play store.
- * altos: update .gitignore files
- * altosdroid: Bump APK version, and re-upload.
-
- [ Bdale Garbee ]
- * further refinment of Releasing document
- * remove local copy of launch-sites.txt and reference to old web location
- * let upstream version rule, don't force use of Debian version in firmware
- * update stlink-pins document to make it clear 4-pin MicroMaTch is our standard STM32L programming connector, and the big MM thing was v0.1 only
- * document what the 'Age' value in the AltosUI display means
- * document what the 'Age' value in the AltosUI display means
- * add pcb overall dimensions and screw sizes the holes are intended for
- * update copyright year to 2013
- * various updates to the text .. more SMA to BNC adapter references, etc
- * improve text in telebt turn-on script
- * document my snazzy new 4-pin to MM v0.1 debug cable
- * name change from MegaMetrum to TeleMega
- * document need for an ARM Cortex toolchain in /opt/cortex, point to build docs
- * point to pkgconfig content in /opt/cortex so stlink stuff works
- * add libssl-dev as a build dep since it's used in FAT filesystem test code
- * update ChangeLog for release
- * update changelog for Debian build
- * add sox as a build dependency
- * update Releasing document to reflect process as of 1.2
- * update configure.ac to reflect version 1.2.1
- * update changelog for 1.2.1 release
- * update Changelog for 1.2.1 release, again
- * unwind debian/changelog to last release
-
- [ Keith Packard ]
- * Bump revision to 1.2 development branch
- * altos: Shrink Pa to altitude table
- * altos: Provide MS5611 configuration option, HAS_MS5611
- * altos/megametrum: Commit for boards with MS5611 baro sensor
- * altos: Re-enable the ms5607 and mma655x acquisition threads
- * altos/megametrum: Use mma655x for acceleration measurements now
- * altos/megametrum: Make MS5607 driver hold SPI bus for whole operation
- * altos/drivers: Use data ring values for MS5607 presentation
- * altos/stm: Clean up SPI pin configuration code
- * altos/telefire: Make sure armed alarm goes off on time
- * altos/stm: Set SPI clock high for disabled SPI busses
- * altos/megametrum: Try running accel and baro in parallel again
- * altos: Compute desired frequency when upgrading from pre-1.1
- * altos: Go back to recording sensor data in globals
- * altos: Fix up ms5607 and mma655x commands to work again
- * altos/telefire: Add siren/strobe support
- * altos: Split task definitions out to ao_task.h
- * altos: Prepare ms5607 driver for use in non-tasking products
- * altos: Allow projects to specify clock at other than 100Hz
- * altos: Allow for other mutex implementations
- * altos: Use alt_t for all Pascal-based altitude data
- * altos: Parameterize altitude table access and initialization
- * altos: Elide ao_altitude_to_pa in flight firmware
- * altos: Clean up types in Pa conversion testing code. Only test to 40km
- * altos: Include struct ao_data declaration only when used
- * altos: Add attiny architecture files
- * altos: Megametrum uses altitude-pa.h, not altitude.h
- * altos: Allow products to define which LED to panic with
- * altos: Add initial micropeak implementation
- * altos: Add (untested) driver for AT24C i2c flash parts
- * altos: Add .gitignore for micropeak
- * altosui: Parse .mega files from command line
- * altos: Document a few member offsets in struct ao_log_record
- * altos: struct ao_log_mega doesn't have a ground temp value
- * altos: Split out ms5607 conversion code for use in ao_flight_test
- * altos: Eliminate implicit 1 byte offset in uint16/int16 functions
- * altos/test: Add ao_flight_test_mm
- * altos: When missing MMA655x, create fake Z accel value
- * altos: Define full-scale gyro and accel values for MPU6000
- * altos/test: Display MPU6000 values in ao_flight_test_mm output
- * altos/telefire: Report valid channels instead of valid pins
- * altos/telelco: Only present valid pads
- * altos/telelco: Handle case where no boxes are present
- * altos/telelco: Actually set pad when it changes
- * altos/stm: Declare all SPI bus speeds
- * altos/telelco: Crank up SPI speed to cc1111
- * altos/telelco: Only display every 10th box number during scan
- * altos/telelco: 10ms is not enough time to get a packet back
- * altos/telelco: Make the RSSI led turn red when no packet is received
- * altosui: Handle missing pad distance in descent tab
- * altosui: Print exception stack trace when tracking flights
- * altos/avr: Use ISR_BLOCK to disable interrupts during slave ISR
- * altosui: Accept serial number of zero for eeprom download
- * altos: Only enable PWM on telescience_pwm product
- * altos: Add telescience-pwm product
- * altos: Build telescience-pwm product when possible
- * altos/megametrum: Switch back to using the MS5607
- * Bump version to 1.1.9.1
- * altosui: Re-add a couple of "unused" values
- * altos/stm: Stop spewing clock out PA8 pin
- * altosui: Add new filename filters
- * altosui: Correct megametrum eeprom filename date
- * altoslib: MegaMetrum eeprom never loses GPS date
- * altoslib: remove a couple of TM log record types from MM log parsing
- * altoslib: Compute accelerometer speed from megametrum eeprom data
- * altoslib: Move computed state from AltosRecord to AltosState
- * altoslib: Parse GPS .mega file entries for reply/graphing
- * altos: Document mega log packet types
- * altosui: Handle .mega files in Landed tab 'Graph Flight' button
- * altos/test: Use MMA655X in ao_flight_test_mm. Add run-mm to plot mm data
- * altoslib: Add AltosRecordNone.java
- * altosdroid: AltosState now has speed and max_speed funcs
- * altos: Add state comparisons to pyro channel conditions
- * altosui/altoslib: Add support for configuring pyro channels
- * altoslib: capitalize 'Invalid' state name appropriately
- * altos: Let AVR products override the stack size. Set telepyro to 104
- * altos: Allow pyro flight state config to be set
- * altos: make check-avr-mem utility executable
- * altosui: Allow any non-basestation to be configured
- * altosui: Allow AltosConfig to abort before serial line starts
- * altos: When slave mode first starts, accept any packet
- * altos: Force beep timer regs reload when enabling beeper
- * altos: Add ao_arch_block/release_interrupts to avr and cc1111
- * altos: profiling on STM32L
- * altos: Replace __critical usage with ao_arch_critical as needed
- * altos: Add stack-guard code. Uses STM MPU to trap stack overflow.
- * altos: Add task queues.
- * altos/megametrum: Depend on Makefile contents for build
- * Bump version to 1.1.9.2
- * altos: Switch drivers to ao_arch_block/release_interrupts
- * altos: Wrap ao_container_of value in parens
- * altos: Clean up cc1111 architecture macros a bit, removing cli/sei
- * altos: Clean up stm arch macros a bit.
- * altos: Leave interrupts disabled while checking for task to run
- * altos: Provide ao_task_alarm_tick to reduce per-tick cost
- * altos/attiny: Update to new interrupt macros
- * altos/micropeak: Switch to MS5607 sensor. Require 4m for boost. Elide dead code
- * altos: Build micropeak when avr-gcc is available
- * doc: Add micropeak manual
- * altos/micropeak: Set boost detect to 10m. Add 30s boost delay.
- * altos/attiny: Don't initialize the CS pin in the general SPI setup
- * altos/micropeak: Clock micropeak at 250kHz to save power
- * altos/micropeak: Run MS5607 at max resolution for micropeak
- * altos/attiny: Remove debugging code which frobs PB1
- * altos/stm: Support LEDs on multiple ports
- * altos: Remove 'volatile' from ao_rssi.c globals
- * altos: Remove legacy telemetry from ao_monitor when not needed
- * altos/megadongle: Add megadongle product
- * altos: Build megadongle when possible
- * doc: Start updating AltOS documentation for multi-arch
- * altoslib: Add (disabled) conversion for MS5611
- * altos: fix cc1120 radio test - state wasn't made static
- * altos: Make Tm recovery mode set RF cal and callsign too
- * altoslib: MegaMetrum data telem packets have sensor data, not flight no
- * altoslib: Allow flight number to be zero
- * altoslib: Reset telem tracking state when switching altimeters
- * altos: Clean everything, even if we don't have compilers
- * doc: Minor updates to the micropeak docs
- * altos: micropeak LED is orange now, not blue
- * altos: Slow down micropeak report timing
- * altos: Make TeleBalloon v1.1 build again
- * altos: Share getnibble function
- * altos: Shrink cc1111/ao_dbg.c a bit
- * altos: Share cc1111 reset/debug-start code
- * altos: Make stdio 8-bit clean by making pollchar return int
- * altos: Add support for 115200 baud serial rates
- * altos: Use ao_xmemcpy in ao_log_telem.c
- * altos: Add ao_task_minimize_latency to reduce IRQ delays
- * altos: Expose GPS serial fifo on MegaMetrum
- * altos: Add support for reflashing skytraq GPS chips
- * ao-tools: Add ao-sky-flash to update GPS firmware
- * altos: Make skytraq reflashing code try both 9600 and 4800 baud
- * ao-sky-flash: Clean up debug printfs a bit
- * ao-tools. Oops, let 'ao-mega' slip into build.
- * Another ao-mega addition which shouldn't be here
- * altos: shrink ao_companion_status by merging printf calls
- * altos: Break out GPS speed resetting sequence
- * altos: Add Pico Beacon code as ao_aprs.c
- * altos: Make aprs code output encoded packets to stdout
- * altos: Add test scaffolding for APRS
- * altos: Generate all of the APRS messages
- * altos: Add missing ao_aprs.h file
- * Signed-off-by: Keith Packard <keithp@keithp.com>
- * altos: Strip out everything but the basic position reporting from APRS
- * altos: Reduce printf calls in APRS packet generation
- * altos: Remove more unused APRS code
- * altos: More APRS trimming
- * altos: Remove APRS sine-wave table
- * altos: Remove a bunch of time bits from the APRS code
- * altos: Start restructuring APRS code to create and send packets
- * altos: Prepare APRS for use within altos itself
- * altos: Hook APRS up to the radio
- * altos: Hook up APRS to telemetry loop
- * altos: Allow telemetry, rdf and APRS to be individually controlled
- * altos: Send APRS packets even during ascent
- * altos: Shrink 'ao_version' by calling printf fewer times
- * altos: Change 'flight-number' to 'current-flight'
- * altoslib: Make AltosMs5607 capable of parsing ms5607 info lines
- * altoslib: Make AltosConfigData parse all of the config data
- * altosui: Use AltosConfigData for altosui configuration dialog
- * altos: fix functions calling pollchar to use 'int' to hold the value
- * altos: Fix up APRS packet sending code in cc1120 driver
- * altos: Make APRS interval configurable
- * altos: Use configured callsign in APRS packets
- * altosui: Call config UI from AltosConfigData directly
- * altosui: Add APRS interval configuration to UI
- * altos: Fix aprs test to not allow callsign configuration
- * altos: Stop including profiling and stack guard code in megametrum
- * altos: Store altitude in 32-bits for MicroPeak
- * altos: Make sure pa to altitude conversion is done with 32 bits
- * altos: Use alt_t value to hold displayed height in micropeak
- * altos: Increase MicroPeak blink times a bit
- * altos: Tim Van Milligan suggestion for µP -- delay before showing last flight
- * altos: Add load-slow target for MicroPeak
- * altos: Log in-flight data for MicroPeak
- * doc: Update MicroPeak doc to include EEPROM and programming info
- * altos: Note that Lithium battery may be included with MicroPeak
- * altos: Log baro readings for MicroPeak
- * altoslib: Only list flight logs for boards that we know have them
- * altoslib: Discard previous flight state on SN change
- * doc: Add paragraph noting differences in JST polarity
- * doc: Add warning about matching battery voltage.
- * altoslib: unconfigured radio frequency data is now -1, not 0
- * altos: Round APRS data correctly
- * altos: Document what HAS_BOOT_RADIO does in the m25 driver
- * altos: Test APRS rounding by using coordinates near the boundary
- * altos: Wire up another CC1120 GPIO to get MARC status changes
- * altos: Add new MARC status pin interrupt bits to megadongle
- * altos: Re-enable beeper on megametrum
- * altos: Average MPU6000 values on ground for later use
- * altos: Make micropeak 'serial' interface work
- * altos: Add distinct LED pattern before writing log data
- * altosui: Clean up graph a bit, remove shapes, improve tooltips
- * altos: Actually record ground averages for 6dof sensor
- * Move libaltos to top level
- * Start building MicroPeak GUI tool
- * Add file chooser for MicroPeak
- * Lots more work on the MicroPeak application
- * altos: Fix cc1120 debug code to build on megadongle
- * altos: Fix MegaDongle CC1120 chip select pin
- * altos: megadongle radio int is C13, not C14
- * Create altosuilib to share code between altosui and micropeak
- * altoslib: Add units change notification list
- * micropeak: Use altosuilib
- * micropeak: Add flight stats pane
- * Allow CC1120 to sit on other SPI busses
- * micropeak is code complete now.
- * micropeak: Fix chart colors
- * micropeak: Add 'Close' menu item. Fix start location
- * Build installable versions of MicroPeak GUI
- * Build micropeak by default
- * micropeak: Check CRC on downloaded
- * Rename AltosConfigureUI to AltosUIConfigure
- * libaltos: Remove a couple of spurious debug printfs
- * altosui: Use altosuilib for configuration
- * altosui: Remove AltosVersion.java
- * altosui: Use shared AltosDeviceDialog
- * altosui: Use shared AltosFontListener class
- * altosui: Use shared AltosUIFrame and AltosUIDialog
- * altosui: Use shared AltosUIListener
- * altosui: Remove duplicate AltosUSBDevice
- * altoslib: Remove unused fake product_micropeak_serial
- * micropoint: Add MicroDataPoint
- * micropeak: Add CSV export
- * micropeak: Add view of raw data in GUI
- * altosuilib: Fix install issues on Linux
- * micropeak: Use JTextArea instead of TextArea
- * micropeak: Change graph tooltip units on the fly
- * micropeak: Add Mac OS Info.plist file
- * micropeak: Add command line export option
- * micropeak: Export in lots of units
- * micropeak: Use data.export for Raw display. Change to MPH
- * Add separate code path for listing FTDI devices
- * micropeak: Remove debug printf for command line
- * micropeak: Move raw view caret to top. Make raw text uneditable
- * micropeak: Use new libaltos entry point for FTDI devices
- * micropeak: Create .dmg file for apple. Create micropeak-jdb script
- * micropeak: Suggest filenames for saving data
- * micropeak: Create Mac OS X package
- * micropeak: Add ReadMe.rtf to Mac distribution
- * altosui: Create .dmg file for Mac OS X installations
- * altoslib: Don't smash existing GPS pad alt after boost
- * altoslib: Clean up AltosRecord clone methods
- * altos: Time out reading packet data from cc1120 after 100ms
- * libaltos: Need to check for tty/ttyACMx before ttyACMx
- * Fix up 'make fat' to build all libs and micropeak too
- * micropeak: Report recorded apogee instead of searching flight data
- * micropeak: Demonstrate how to hide various parts of the graph
- * micropeak: Create 'micropeak' script correctly
- * micropeak: Note when libaltos fails
- * altosui,micropeak: Link altoslib.jar and altosuilib.jar before compiling
- * altosui: Reference altosuilib.jar and altoslib.jar from original dirs
- * micropeak: Record samples before boost detect
- * altos: Initial telescience bits
- * Update avr ao_spi_slave code to match API changes
- * altos: Build telescience-v0.2
- * altos: Set STM GPIO output speed for SPI pins correctly
- * altos: Crank fast SPI on STM to 8MHz
- * altos: Change CC1120 SPI speed to 4MHz.
- * doc: Add simplesect headers to release notes
- * altos: Correct model error covariance matrix
- * altos: Add computation of MicroPeak Kalman correction coefficients
- * altos: Add Kalman filter to MicroPeak
- * micropeak: Show decimeters in stats window
- * micropeak: Fetch Mac and Windows drivers when creating packages
- * Tag version 1.1.9.3
- * altosi: callsign could not be configured for AltosUI
- * altosui/micropeak: Let native window system place windows
- * altosui: All of the Altos class is actually in AltosUILib now
- * altosui: Remove duplicate AltosUIPreferences.java
- * altosui: Make initial AltOS window position configurable
- * micropeak: Respect font size preference in MicroPeak stats tab
- * Add documentation for the MicroPeak USB interface
- * micropeak: Add mac build file Info.plist
- * micropeak: fix 'make clean' and .gitignore
- * Mark MicroPeak as a recording altimeter, not a peak-recording altimeter
- * Change AltosLib to altoslib
- * Add version numbers to java libraries
- * altoslib: fix Makefile JAR target
- * micropeak: Update Makefile to versioned Java libraries
- * altos: Document which MPU6000 revs have broken accel values
- * test: Accept micropeak CSV files for micropeak testing
- * altos: Add atmosphere.5c
- * doc: Add TeleMetrum and TeleMini drill templates
- * altosuilib: Remove duplicate AltosUnitsListener.java
- * altosuilib: Add graphing routines from MicroPeak
- * micropeak: Use altosuilib graphing functions
- * altoslib: Add AltosUnits.graph_format
- * altosuilib: Initialize graph axes units
- * altoslib: Fix altoslib install
- * altosuilib/micropeak: Add state markers to micropeak graph
- * altosui/altoslib/altosuilib: Switch altosui to shared graph code
- * altoslib: Fix a couple of unit functions to make them public
- * altosui: Adjust graph voltage tool-tip value format
- * altosui: Add callsign to Monitor Idle window (Trac #62)
- * altosui: Interrupt MonitorIdle when changing frequency/callsign
- * altosui: Display callsign in connecting message window
- * altoslib: Fix available flight log storage computation
- * altosui: Display block number while downloading flights. Track #51
- * altosui: Display count of erased flights along with their numbers
- * altosui: Add map and GPS data to graph window. Trac #50
- * Build Windows .nsi files in configure script
- * micropeak: Remove Info.plist
- * altosuilib: rescale axis when enabling data series
- * altosui: Stick file basename in graph window title
- * altosui: Remove graph series which aren't available
- * altosui: Fix AltosLanded call to AltosGraphUI
- * altos/stm: Add more bits to NVIC register definitions
- * Update build version to 1.2
- * altos/driver: Make HMC5883 driver build again
- * altos: telescience-v0.2 is an ARM product
- * altosuilib: Add setNotify/fireSeriesChanged methods to AltosUIGrapher
- * altosuilib: Disable graph element notifies for each add()
- * doc: Document how to get TeleMini to 'emergency recovery' mode
- * doc: Add version 1.2 release notes
- * libaltos: Open FTDI serial devices twice on Windows.
- * ao-tools: Add ao-dumpflash program
- * altoslib: Invalidate GPS new data bit when updating state
- * altosui: Add N/S and E/W to info table lat/lon values
- * ao-tools/lib: Add cc_telemetry_unparse
- * ao-tools: Add ao-edit-telem
- * altos: re-enable optimization for stm-demo. remove unused bits
- * micropeak: Improve download docs and UI
- * ao-tools: add ao-dump-up
- * Add telegps initial version
- * ao-tools: Make library support µPusb
- * altos: Add cc115l driver (untested)
- * altos/telegps: Hook up cc115l driver
- * altos: Add RFPA0133 amplifier driver
- * altos: Improve CC115L driver. Generates carrier now.
- * altos/stm: Ensure SPI always sends 0xff during receive
- * altos: Allow radio recv and xmit to be separately configured
- * altos: Fix config to not abort radio recv when no recv is available
- * altos: Add SDCARD and FAT16 filesystem support
- * altos: Hook up the FAT16 and SD card support to telegps
- * altos: Add new panic flag for bufio misuse
- * altos: Teleshield has a radio, set HAS_RADIO in ao_pins.h
- * altos: Use FTDW, clear DATA bit. Disable backup write protection
- * altosui: Don't deref null pyros when saving altimeter config
- * altos: Add sanity checking to busy counts in bufio driver
- * altos: Clean up fat driver API. Improve fat test
- * altos: Add a simple cache for the FAT position->cluster computation
- * altos: seek forward on FAT cluster chain instead of restarting
- * altos: Add FAT32 support. And lots more testing.
- * altos: Add temporary RF power settings
- * altos: Get CC115L radio working.
- * altos: Configure cc115l sync byte count for each radio mode
- * altos: Lock cc115l radio mutex when using global radio values
- * altos: Export ao_fat_sync and ao_fat_full functions
- * altos: Add logging and telem to telegps
- * altos: Add SD card writing function
- * altos: Disable CC115L debug commands
- * altos: Move fat mount information to separate command.
- * altos: Add sdcard read/write tracing
- * altos: Do not release interrupts from any pollchar function
- * altos/stm: Add debugging mechanism to STM USB driver
- * altos/stm: Always check for idle IN buffer before sending
- * altos: Don't add fat commands when building ao_fat_test
- * altos: Unmount file system after each testing pass in ao_fat_test
- * ao-tools/ao-stmload: Be smarter about ELF parsing. Retry open on failure.
- * altos: Fix command-line FAT filename parsing
- * altos: Increase SD card timeout at startup time
- * altos: Make ao_fat_readdir return real error values instead of 1/0
- * altos: Create the log file if it doesn't already exist
- * altos: Flush the on-board mega log after every sample interval.
- * altos: let FAT tracing work in ao_fat_test as needed
- * altos: Make sure FAT cluster allocation works for size zero files
- * altos: Support open on multiple simultaneous FAT files
- * altos: Add a FAT test that re-writes the same file multiple times
- * altos: Provide build hooks for sampling profiler in telegps
- * altos: Retry SD card I/O. Use time for timeouts instead of counts
- * altos: Add defines for the specific pins used for telegps SPI
- * altos: Horrible kludge -- disable radio while talking with SD card
- * altos: Shorten SD initialization timeouts.
- * Set telegps USB id to 0025
- * altoslib: Make any incoming telem packet update the RSSI value
- * altosui: Don't display missing sensor data
- * altosui: Hide flight-related tabs for telegps
- * altosui: Display current GPS in 'pad' tab for 'startup' staten
- * altosui: Graph TeleMini flights without crashing
- * altos: Try RDF mode for TX calibration
- * altos: Create telebt-v1.0 product. Remove old telebt products
- * altos: Create telebt-v1.0 product. Remove old telebt products
- * altos: Monitor battery voltage on telebt
- * altoslib/altosui: Carry receiver status around in AltosListenerState
- * altoslib/altosui: Adapt monitor idle to new AltosListenerState
- * doc: Add an outline of an AltosDroid chapter
- * altosdroid: Hook up the position listeners
- * altosdroid: Send LOCATION and CRC_ERROR messages to UI.
- * altosdroid: Mike was right -- only need one LocationListener
- * altoslib: Add range and elevation to AltosGreatCircle
- * altosdroid: Compute course from android device to rocket, display it
- * altoslib: Remove spurious debug message
- * altosdroid: Check state.gps != null before using it
- * altosdroid: The Map already draws our location; no receiver marker needed
- * altos: Delay while waking up SD card a bit
- * altos: Stick a mutex around FAT operations
- * altos: Don't include bufio debug commands by default
- * altoslib: Remove spurious debug message
- * altos: Make sure the packet format is set reasonably for radio test
- * libaltos: Retry Windows serial port open five times
- * Windows: Add all of the AltusMetrum USB IDs to telemetrum.inf
- * altosdroid: Shrink text so it fits on my phone
- * altosdroid: Show our position in the map tab. Squeeze to fit phones
- * altosdroid: Get rid of a couple of startup messages
- * altosdroid: Update UI even if no telem has been received. Center map.
- * micropeak: Oops. Lost the call to actually start downloading data
- * altoslib: Check for null state.gps before accessing it in eeprom records
- * altosui: remove debug message from AltosFlightUI
- * altosdroid: Check for missing values
- * altosui: Handle broken network in map tile loading
- * altosui: Disable main deploy setting for TeleGPS
- * altosdroid: Fix integer formatting in tabs
- * altosdroid: Update distance/bearing on map tab
- * doc: Add a bunch of Altos Droid material to the docs
- * doc: Start filling in details about Altos Droid flight monitoring
- * libaltos: Try Bluetooth open 5 times on EBUSY
- * libaltos: Delay after opening bluetooth device on linux
- * altosdroid: Add Notebook to track feature requests
- * altosdroid: Add a few more Notebook entries
- * altosdroid: Add request for sat images to AltosDroid Notebook
- * Move cortex toolchain to /opt/cortex
- * altos: Re-generate TeleMega bits
- * Re-add telemega outline pictures
- * altos: Make SD card driver compile without radio support
- * altos: Add MR25 everspin MRAM driver
- * altos: Add TeleMega v0.3 support
- * altos: Build telemega-v0.3 by default
- * altos: All STM ADC users need to declare HAS_ADC_TEMP
- * altosdroid: Add wish for persistent TBT and freq settings
- * Allow build without SDCC
- * altos: Expose ao_put_string function
- * altos: Call ao_task_init before initializing any drivers
- * altos/stm: Always declare all romconfig variables
- * ao-tools/lib: Deal with binary USB data in debugging output
- * altos/stm: Remove USB EP0 task
- * altos: Make telemega-v0.3 binary use the right name
- * altos: Build test framework for AES code
- * altos: Provide timeout value to ao_radio_recv
- * altos: Make cc1120 driver wait for TX finished
- * altos: Clear any broken cc1120 TX fifo bits before transmitting
- * altos: Allow LCD segments to not be multiplexed across digits
- * altos: Add telelco-v0.2 project
- * altos: Add nickle micropeak log parsing code
- * altos/test: Add telemega plot helper script
- * altos: Ignore ao_aes_test binary
- * altos: Build test framework for kalman filter
- * altos: Add .gitignore to kalman test dir
- * altos: Add ublox checksum app to generate ublox config lines
- * altos: Add a bunch of .gitignore files
- * altos: More .gitignore bits
- * altosdroid: Add Notebook entry for reloading telem data option
- * altos: Compute "real" RSSI value in radio code as needed
- * altos: Reconfigure CC1120 receiver to match our usage
- * altos: Make cc1120 driver return false on recv timeout
- * altos: Stop using telelco v0.2 top LEDS for radio TX/RX
- * altos: Open up the DVGA gain to use all of the available settings
- * altos: Reduce stack usage of FAT driver and logger
- * altos: Use separate exception stack on STM32L
- * altoslib: Update GPS state even if new state is unlocked
- * altos: Mark GPS telemetry packets with GPS time stamp
- * altos: Use SYSTICK on STM32L
- * altos/test: Fix warning in ao_aprs_test
- * altos: Set APRS deviation to 3kHz
- * altos: Elide M25 debug output from storage info command
- * altos: Sanity check barometer before going to pad mode
- * Add STM self-flashing loader
- * altos: Make stm-flash capable of switching to application
- * altos: Add program flash function
- * altos: Clean up boot loader support
- * altos: Add actual flashing functions to stm-flash app
- * altos: Fix up stm-flash output file name. Use discovery LED pins
- * altos: Mark .boot section as (NOLOAD)
- * altos: Validate boot chain start address
- * altos: Fix STM flash programming
- * altos: Add erase command to stm-flash app. Validate addresses.
- * altos: Create ihx version of stm-demo
- * altos: Switch ao_stm_flash to read/write binary blocks
- * altos/stm: Add .elf to .ihx rule
- * altos/stm: Add comments to the .ld files explaining how the romconfig stuff works
- * ao-tools/lib: Add loading support for 32-bit ihx files
- * ao-tools/ao-stmload: Fix ELF, add IHX, add self-flashing
- * altosui: Support 32-bit ihx files
- * altosui & altoslib: Move a pile of debug/programming bits to altoslib
- * altosui/altoslib: Move more flashing code from altosui to altoslib
- * ao-tools/ao-stmload: Remove IRC dregs in source code
- * altos: Move ao_notask to core
- * altos: Eliminate stdio looping when system has a single stdio source
- * altos/stm: Don't define task macros when not tasking
- * altos/stm: Allow core timer to be excluded from build
- * altos/stm: Shrink stm flash loader to < 4kB
- * altos/stm: Provide another 4kB of flash space for apps
- * altos: Use flash loader on all STM products
- * ao-tools: reboot to loader now uses 'X' instead of 'L'
- * ao-tools/ao-stmload: application base moved to 0x08001000
- * altos/stm-flash: Check target flash address against AO_BOOT_APPLICATION_BASE
- * altos: Allow STM usb driver to be used without stdio
- * altos: Run self loader when application sets boot addr to 0
- * altos: Make stm-bringup build again
- * altos: Get rodata into flash, make sure sections are aligned
- * altos: Remove stdio from stm-flash
- * ao-tools/ao-stmload: Add --verbose flag
- * altos: Add ao_boot_chain to telemega v0.3
- * altos/stm: Create per-product flash loaders
- * altos: Wait after configuring boot pin before testing it
- * Add altosdroid notebook entry for imperial units
- * altoslib: Add non-persistent 'last logdir' preference
- * Information from configure about android build was misprinted
- * micropeak: Use new 'last logdir' preference for MicroPeak save/load dialogs
- * altosui: Wait for valid callsign/flight when graphing
- * altoslib: Correct hexfile address ranges
- * altosuilib: Mistake in the MegaDongle listing -- was set to TeleMega
- * altos: Don't bother fixing telelco-v0.1, just disable it
- * altos: Add U-Blox GPS driver
- * altos: Provide a define for the number of sat infos in a telem packet
- * altos: Switch TeleMega v0.3 to u-blox
- * altos: Struct used for u-blox testing had lat/lon swapped
- * altos/test: ao_gps_test_ublox uses ao_gps_blox.h
- * altoslib: Use sequence numbers to track GPS updates to AltosRecord
- * altosui: Use GPS alt + baro height for KML altitude
- * altosui: Generate useful KML files from TeleGPS logs
- * altos: Use symbolic names for ublox packet id
- * altos: Set u-blox navigation settings
- * altos/cc1111: Hack on USB driver to make Windows happy
- * libaltos: use PurgeComm in Windows altos_close to abort in-progress ops
- * libaltos: Build the linux library targets when doing a 'fat' build
- * altos/telemega: The last two igniters are apogee and main
- * Create release notes for 1.2.1
- * doc: Update description of graph window to note new tabs (config and map)
-
- [ Robert Garbee ]
- * telescience: steal last adc channel for icp3 most recent value Make the ICP3 rpm counter use in ao_adc_avr.c optional
- * first work on PWM input to TeleScience, 'p' command displays timer 1
- * Timer 3 working with slower clock and all 16 bits.
- * ICP3 working
- * telescience: correctly calculating rate values with higher resolution
-
- -- Bdale Garbee <bdale@gag.com> Tue, 21 May 2013 09:43:47 -0600
-
-altos (1.1.1-1) unstable; urgency=low
- * new upstream bug-fix release
- - fix flight data deletion problem affecting TeleMetrum v1.0 boards only
- - fix broken Google Earth export from on-board flight data (.eeprom) files
- - fix units displayed on "Landed" tab in UI to honor imperial units flag
- - display both range to the rocket and ground distance in "Descent" tab
- - fix bug in sensor data display for TeleMini in "Monitor Idle" mode
-
- -- Bdale Garbee <bdale@gag.com> Sun, 16 Sep 2012 14:07:23 -0600
-
-altos (1.1-1) unstable; urgency=low
-
- * new upstream minor release, which provides a few new features in AltosUI
- and the AltOS firmware, and fixes bugs
- - Add apogee-lockout value. Overrides the apogee detection logic to
- prevent incorrect apogee charge firing. A configuration menu
- provides a list of reasonable values, or the value can be set by hand.
- - Fix a bug where the data reported in telemetry packets was from
- 320ms ago.
- - Force the radio frequency to 434.550MHz when the debug clock
- pin is connected to ground at boot time. This provides a way
- to talk to a TeleMini which is configured to some unknown frequency.
- - Provide RSSI values for Monitor Idle mode. This makes it easy to check
- radio range without needing to go to flight mode.
- - Fix a bug which caused the old received telemetry packets to
- be retransmitted over the USB link when the radio was turned
- off and back on.
- - Fix a bug that caused GPS ready to happen too quickly. The
- software was using every telemetry packet to signal new GPS
- data, which caused GPS ready to be signalled after 10 packets
- instead of 10 GPS updates.
- - Fix Google Earth data export to work with recent versions. The
- google earth file loading code got a lot pickier, requiring
- some minor white space changes in the export code.
- - Make the look-n-feel configurable, providing a choice from
- the available options.
- - Add an 'Age' element to mark how long since a telemetry packet
- has been received. Useful to quickly gauge whether
- communications with the rocket are still active.
- - Add 'Configure Ground Station' dialog to set the radio
- frequency used by a particular TeleDongle without having to go
- through the flight monitor UI.
- - Re-compute time spent in each state for the flight graph; this
- figures out the actual boost and landing times instead of
- using the conservative values provide by the flight
- electronics. This improves the accuracy of the boost
- acceleration and main descent rate computations.
- - Make AltosUI run on Mac OS Lion. The default Java heap space
- was dramatically reduced for this release causing much of the
- UI to fail randomly. This most often affected the satellite
- mapping download and displays.
- - Change how data are displayed in the 'table' tab of the flight
- monitoring window. This eliminates entries duplicated from the
- header and adds both current altitude and pad altitude, which
- are useful in 'Monitor Idle' mode.
- - Add Imperial units mode to present data in feet instead of
- * update build-deps to use cc1111 intead of sdcc, closes: #676739
- * update build-deps to use default-jdk, closes: #655580
-
- -- Bdale Garbee <bdale@gag.com> Thu, 13 Sep 2012 14:46:50 -0600
-
-altos (1.0.3) unstable; urgency=low
-
- [ Bdale Garbee ]
- * lose the bluetooth lib dependency until it's relevant
- * don't try to include bluetooth headers
- * don't try to link bluetooth lib
- * mention release notes in Releasing file prep stage
- * more notes on release notes in Releasing
- * releasing 1.0.3
-
- [ Keith Packard ]
- * altos: Create TeleMetrum v1.2 directory
- * Add 1.0.3 release notes.
-
- -- Bdale Garbee <bdale@gag.com> Sun, 25 Dec 2011 19:08:56 -0700
-
-altos (1.0.2) unstable; urgency=low
-
- [ Bdale Garbee ]
- * update release process docs
- * update changelogs for Debian build
- * include 1.0.1 release notes in docs, closes: #642705
- * add run-time dependency on libjfreechart-java
-
- [ Keith Packard ]
- * altos: Delay reboot by a second to avoid re-entering idle mode
- * Bump to version 1.0.2
- * altos: TM: Don't turn on packet slave mode until idle/invalid state
- * doc: Add 1.0.2 release notes
-
- -- Bdale Garbee <bdale@gag.com> Wed, 28 Sep 2011 01:58:27 -0600
-
-altos (1.0.1) unstable; urgency=low
-
- [ Bdale Garbee ]
- * use multimaint-merge to make Debian changelogs less ugly
- * update TeleMini turnon script now that we've made a stable firmware release
- * moving git-buildpackage config into .git/ since it is fairly specific to
- Bdale's build environment, and doesn't need to be in the source package
- * get ready for a 1.0.1 release
- * update changelogs for Debian build
- * fix telemini firmware path name
- * ignore generated log file
- * roll release notes version from 1.0 to 1.0.1
- * roll back packaging changelog for rebuild
-
- [ Keith Packard ]
- * altos: Clear callsign on initial config load
-
- -- Bdale Garbee <bdale@gag.com> Fri, 26 Aug 2011 10:39:29 -0600
-
-altos (1.0) unstable; urgency=low
-
- [ Keith Packard ]
- * altos: Lost change that reported flight 0 when log memory was full
- * altosui: Ancient log files used 'apogee' for 'coast' state
- * altosui: Add 'On-board Data Logging' indicator to pad tab
-
- [ Bdale Garbee ]
- * update changelogs for Debian build
- * update changelogs for Debian build
-
- [ Keith Packard ]
- * altosui: remove debug printf in pad pane
- * altosui: Disable 'max flight log' config when there are stored flights
- * altos: Merge common config code in ao_config.c
- * Bump version to 0.9.7
- * altos/altosui: Add ability to disable telemetry/rdf completely
- * altosui: Clean up command line processing. Add --graph
- * altos-fat/windows: Check and install Java 1.6 as needed
- * altosui/windows: Fix a bunch of windows compiler warnings.
- * altosui: Attempt to make both 32- and 64-bit windows DLLs
- * doc: Add note about telemetry disable mode to 1.0 release notes
- * doc: Add Installation Recommendations chapter
- * altosui: Add a few simple unit conversions
- * altosui: Capture date/time/serial/flight in AltosFlightStats
- * altosui: Add date/time/serial/flight to flight stats tab
- * altosui: Show filename in AltosGraph window
- * altosui: Add --summary option to dump flight stats to stdout
- * altosui: Make monitor-idle display correct 'On-board data logging' status
- * altosui: Can't configure flight log max on TeleMini
- * altosui: fix 'magic' string to signal end of config data
- * altosui: Only 'show' config dialog once
- * altosui: Reset all config data on 'reset' command
- * altosui: Update mac os X library
- * libaltos: fix Mac OS X function signatures
- * altosui: add tool-tips to the button box.
-
- [ Bdale Garbee ]
- * turn off auto-tagging during Debian build
- * update changelogs for Debian build
- * rewind changelog to 0.9.6.0 for rebuild
- * update changelogs for Debian build
-
- [ Keith Packard ]
- * altosui: Use system look&feel
- * Remove stale tools (ao-dumplog, ao-postflight, ao-view)
- * altosui: Add tool-tips to config dialogs
- * altosui: Try to get dialogs to look a little better
-
- [ Bdale Garbee ]
- * another test round
- * roll changelog back in prep for another test build
- * update changelogs for Debian build
- * add pkg-config to the build deps
- * prepare for another rebuild
- * update changelogs for Debian build
-
- [ Keith Packard ]
- * altosui: Don't trust companion telemetry record 'channels' count
- * altosui: Make flight monitor font size configurable
- * altos/windows: Get latest JRE 1.6 version (Version 6 update 27)
-
- [ Bdale Garbee ]
- * doc tweaks through chap 3
-
- [ Keith Packard ]
- * doc: Spelling corrections in altusmetrum.xsl
- * doc: Document pad-mode 'on-board data logging' indicator
-
- [ Bdale Garbee ]
- * more doc tweaking
-
- [ Keith Packard ]
- * doc: Describe packet command mode a bit better.
- * doc: Move Packet Command Mode section to System Operations chapter
-
- [ Bdale Garbee ]
- * more doc tweaks
- * more tweaks
-
- [ Keith Packard ]
- * doc: use 'radio link' to refer to packet command mode
-
- [ Bdale Garbee ]
- * more tweaking
-
- [ Keith Packard ]
- * doc: Move updating device firmware section to separate chapter
- * doc: Updating Firmware is now a separate chapter
-
- [ Bdale Garbee ]
- * more changes
-
- [ Keith Packard ]
- * doc: Move the remaining command-mode descriptions to the appendix
-
- [ Bdale Garbee ]
- * tweak tweak tweak
-
- [ Keith Packard ]
- * doc: Describe max flight log, ignite mode and pad orientation
- * doc: Remove duplicate documentation about max flight log
-
- [ Bdale Garbee ]
- * more tweaks
- * prepare to release
- * don't deliver sources.list fragment in official Debian packages
- * changes in preparation for upload to Debian
- * ao-view is no longer included in the altos package, so have the
- old-style Debian menu entry point to altosui instead
- * rewind packaging changelog to last tagged version
- * update desktop file for consistency with package section
- * we need a main category in the desktop file
- * really, I mean it, no longer deliver the sources.list fragment
- * add a postinst to remove sources.list.d fragment delivered by old
- private versions of this package, no longer needed once we have
- official packages
-
- -- Bdale Garbee <bdale@gag.com> Thu, 25 Aug 2011 02:22:21 -0600
-
-altos (0.9.6.0) unstable; urgency=low
-
- [ Keith Packard ]
- * altos: Correct flight log max on Tm to 5k
- * altosui: Change button to 'Configure Altimeter'
- * altos: Remove pad_orientation functions from non-accel devices
- * altos: Add ability to set arbitrary radio frequency
- * altosui: Add dialogs to configure 'common' frequencies
- * altosui: Convert from channels to frequencies
- * Set version to 0.9.5.0
- * altosui: altimeter is not spelled altimter
- * altosui: Pull out BlueTooth support
- * altos: minor type in comment about accel correction
- * altosui: Must set radio calibration before radio setting
- * altosui: A few misc cleanups.
- * altosui: Have single radio_to_frequency function
- * altosui: Save frequency after setting it in AltosFlightUI
- * altosui: Show AltosFrequency in scan results
- * altosui: Remove debugging printfs from AltosSerial
- * altosui: Flush radio setting to serial device
- * altosui: Remove unused AltosConfigData from AltosTelemetryReader
- * altosui: Reading serial from swing thread only bad if remote
- * altosui: Make set of telemetries to use while scanning configurable
- * altosui: Add close button to 'fire' dialog
- * altos: Switch telemini from v0.1 to v1.0
- * altosui: Don't export product defs from libaltos
- * altosui: Ensure serial code tracks reply nesting correctly
- * altosui: Ship TeleMini v1.0 firmware with fat blobs
- * Altosui: Add flight statistics tab to graph window
- * altosui: Add a 'Graph Flight' button to the 'landed' tab
- * altosui: Prune telemetry file graphs to just the flight
- * altosui: Plot reasonable data from Tm files
- * altosui: Move launch-sites.txt file to altusmetrum.org
- * Bump version to 0.9.6.0
- * doc: Update altusmetrum.xsl for v1.0 software and TeleMini
- * doc: Document Ignite Mode and Pad Orientation configuration options
- * doc: Describe 'stats' tab in Graph UI, 'Graph Flight' button.
- * doc: Add telemetry docs to debian/linux/mac/windows packages
- * doc: Add release notes, include them in altusmetrum doc. Shuffle altusmetrum
- * doc: Add 1.0 release notes.
- * altos: Pull igniter pins low as soon as possible at boot time
- * altos: Apply igniter boot pulse-width reduction to telemini
- * altos: remove monitor disable stubs from altimeter code
- * ao-tools: ao-list was crashing with more than 3 devices connected
- * libaltos: Mis-allocated device list in libaltos
- * altos: shrink text space from ao_config.c
- * altos: re-write a bit of GPS parsing code to reduce size
- * altos/altosui: Report log format in the version command
- * altos: Don't try to use non-basestations for remote eeprom download
- * altos: Add SPI-based companion board support
- * altos: Put SPI in slower mode when talking to companion board
- * altos: Make sure companion task exits cleanly when done
- * altos: add the 'L' command to show the status of a linked companion board
- * altos: Check for companion init packet validity was busted
- * altosui: Add companion support to the flight UI and CSV conversion
- * altos: Send SPI message at flight state changes
- * altos: Send serial/flight to companion board
- * altos: wait 10s for companion to boot
- * altosui: Clean up eeprom parsing a bit
- * altosui: Add support for TeleScience eeprom download
- * altosui: Devices with log-format can also delete flights
- * altosui: Eliminate inter-chunk flush_input calls
- * altos: AltosSerial.flush_input shouldn't discard Interrupted exceptions
- * altos: Correct AO_CONFIG_MINOR from 6 to 7
- * altos: Reset radio channel to zero when using radio setting
- * altos: use raw height while waiting for landing
- * altosui: don't set channel when using radio setting
- * altosui: Respect storage limits in flight log max config
-
- -- Bdale Garbee <bdale@gag.com> Fri, 19 Aug 2011 22:47:25 -0600
-
-altos (0.9.4.5) unstable; urgency=low
-
- [ Keith Packard ]
- * altosui: Mark empty eeprom records 'invalid', don't generate exception
- * altosui: Always read whole eeprom block, even at end of flight
- * altosui: Display eeprom parsing errors to user
- * Revert "src/ao_gps_skytraq.c: Update logging rate to 10Hz"
-
- [ Anthony Towns ]
- * src/ao_cmd: Shave off bytes from doc strings
-
- [ Keith Packard ]
- * altos: Oops. Lost a couple of commands when merging the doc patch
- * altosui: Missed jcommon.jar in the Mac OS install image
- * Bump published version number to 0.9.1
- * aoview: remove -s option.
-
- [ Anthony Towns ]
- * ao_intflash: Use internal flash for storage
-
- [ Keith Packard ]
- * altos: Make serial, usb, beeper and accelerometer optional components
- * altos/test: Use ao_convert.c instead of hand-coded pres → alt func
- * altos/test: Add baro-only flight test program
- * altos: Start with packet slave running. Turn off in pad mode.
- * altos: Add TeleMini v1.0
-
- [ Anthony Towns ]
- * ao_intflash: Avoid overwriting code
-
- [ Keith Packard ]
- * altos: Switch LED usage for TeleMini around
- * altos: Switch pins around for TeleMini
- * bringup: Add script for telemini
- * ao-load: Make usb descriptor rewriting optional
- * altos: oops -- altitude reporting wasn't pausing between signals
- * altos: Internal flash ops block when running from flash
-
- [ Anthony Towns ]
- * ignore new flight test file
-
- [ Keith Packard ]
- * altos: Add tiny logging for TeleMini/TeleNano
- * altos: Add kalman filters for baro-only boards
- * altos: Tiny logging fixes. Scan at start, stop when land or full.
- * altos: Add TeleNano support
-
- [ Bdale Garbee ]
- * fix up script to work and have reasonable texts
-
- [ Keith Packard ]
- * altos: Fix mini/nano default log size to available flash space
- * altos/test: Add scripts to run lots of flights through the code
- * altos: Write height values to log for nano/mini
- * altos: Baro-only boards must not detect launch on accel or speed data
- * altosui: Add software version to Configure AltosUI dialog
- * altos: Don't init packet slave on TD. Make slave start optional
- * altos: Configure packet size from send/recv parameters.
- * altos: Make telemetry interval more consistent
- * altos: Split out tiny telemetry from full telemetry
- * altos: Split telenano main from telemini
- * altos: The kalman code requires a constant sample rate
- * altos: New telemetry report format (version 4). Supports tiny telemetry.
- * altos: Add .sdcdbrc file for teledongle
- * altos: Add nickle kalman implementation.
- * altos: Switch telemetrum over to kalman filter
- * altos: Compute a 'trust' value for the barometer
- * altos/kalman: Kalman terms can be > 1, use 32-bit fixed point
- * altos: Clean up some debug stuff in ao_flight.c
- * altos: Add ao_flight_debug code
- * altos: Missing parens and some bad arithmetic in the kalman code
- * altos: Fix up flight code testing
- * altos: Restore sensible kalman values
- * altos: Ignore alt error for fast->coast. Allow larger error for baro apogee.
- * altos: Exit flight test at landing. Allow description in test flight list
- * Add ao_kalman.h to .gitignore
- * Add description to test flights
- * altosui: Add support for telemetry version 4
- * altosui: Add telemetry format menu and preferences
- * altosui: Remove a bunch of debug printfs from the eeprom manager code
- * altosui: Add support for downloading TeleMini/TeleNano flight logs
- * altosui: Remove extra AltosEepromBlock layer
- * altosui: swing hide/show methods are deprecated
- * altosui: Allow TM config connection to be canceled.
- * altos: Variable log rate in full logging code too
- * altos: full logging must flush pending data before checking state
- * altosui: Off-by-one error in telemetry format configuration UI
- * altosui: Allow radio channel to be configured over the radio link
- * altosui: Tell serial device which frame to use for timeout dialogs
- * altosui: Handle serial calls from swing thread
- * altos: Split up flight code into separate flight/sample/kalman bits
- * altos: Create custom nano flight code
- * altosui: Clean up packet link connecting dialog
- * altosui: Make flight log downloading handle 'Connecting...' dialog
- * altosui: Make deployment testing handle Connecting... dialog
- * altosui: Display exception messages from swing thread
- * altosui: Don't display 0000-00-00 for missing flight log dates
- * altos: ao_sample_preflight was exiting preflight mode immediately
- * altos: Run RDF beacon after apogee instead of waiting for landing
- * altos: Enable logging during nano flights
- * altosui: Parse and export Max flight log value
- * altosui: Only plot acceleration when present in data file
- * altos: Reflect ao_flight split in ao_flight_test dependencies
- * altos: Baro useful ceiling is MSL, not AGL
- * altos: Make ao_flight_test show true height but report saturated height
- * altos: Add initial TeleBT code
- * altos: Add P2SEL_*_MASK defines to cc1111.h
- * altos: expose set of available stdio values
- * altos: Provide for a pre-filter on commands
- * altos: Allow any stdio to be used with packet forwarding
- * altos: Remove serial monitor command
- * altos: Make ao_serial_drain public
- * altos: Clean up usage of serial port for stdio
- * altos: Clean up serial initialization
- * altos: Make cmd echo per-connection instead of global
- * altos: Clean up BT serial communcations
- * altosui: Add missing AltosTelemetryMap.java file
- * altos: Use PIO(6) on BTM to monitor BT connection. Fix BTM init.
- * altosui: Add TeleBT USB device support
- * altosui: Add low-level Bluetooth APIs
- * altos/altosui: Log averaged baro sensor data in Tm/Tn
- * altosui: oops - lost state changes when downloading eeprom data.
- * altos: Write a few pre-launch samples for Tm/Tn devices
- * altosui: Add primitive bluetooth device manager UI.
- * altosui: Create abstract AltosDevice class
- * altosui: Make AltosBTDevice implement AltosDevice interface
- * altosui: Make bluetooth dialog modal
- * altosui: Use persistent list of bluetooth devices for device dialogs
- * altos: Add delays to bt startup sequence
- * altosui: Wait two seconds after bluetooth connect XXX
- * altos: Solidify BT connections
- * altos: Simplify BT communications
- * altos: Remove bt debug command
- * altos: remove BT logging code
- * altosui: Eliminate ao_cmd_filter hook
- * altosui: Make flight data download work through TeleBT
- * altos: add telebt-v0.0 Makefile
- * altosui: Separate out flash debug code to separate thread
- * altosui: Fix TeleBT name in flight monitor title
- * altosui: Display reader name (usually the device) when an I/O error occurs
- * altosui: Move AltosIgniteUI device open out of Swing thread
- * altosui: Fix BT manage dialog so that the device lists resize
- * altos: Add preliminary telebt v0.1 defines
-
- [ Bdale Garbee ]
- * first cut at a telebt turn on script
-
- [ Keith Packard ]
- * altos: Add telebt-v0.1 to Makefile
- * altos: Use USART configuration 1 with flow control for TBT
- * altos: Fix BT link status pin for real TBT hardware
- * altos: pull TBT v0.1 ser_reset line low
- * altos: Add beeper to TBT v0.1
- * altos: Debugging TBT issues -- check pin configuration after boot
- * altos: Initialize beeper for telebt
- * altos: Hook up the P1 ISR for TeleBT v0.1 bt_link line
- * altos: clear CPU port 1 interrupt flag when handled
- * Revert "altos: Debugging TBT issues -- check pin configuration after boot"
- * Switch version to 0.9.4
- * altosui: Handle old TeleDongle receiving kalman telemetry packets
- * altos: Rename telemetry to telemetry_orig
- * altos: Add arbitrary telemetry packet monitoring
- * altos: Add checksum to TELEM output lines
- * altos: Start adding new telemetry frame definitions
- * altos: ao_radio_recv needs byte count *including* rssi and status
- * altosui: Support raw telemetry from TeleDongle
- * doc: Add telemetry format description
- * doc: Complete initial telemetry description
- * doc: Fix a few minor telemetry doc mistakes
- * Version strings must be < 8 bytes long
- * altos: teledongle does not need ao_packet_slave.c
- * altos: Shrink const space in ao_config
- * altos: Add sat info to GPS report command
- * altos: Shrink help text
- * altos: Add split telemetry code
- * altos: Complete new telemetry switchover
- * altosui: Parse remaining standard telemetry packets
- * doc: Chang Config and Location packets
- * altos: Adapt to changes in telemetry Configuration packet
- * doc: Add section about TeleDongle USB line format
- * altosui: Elide nul bytes at end of telemetry string values
- * altosui: Elide missing values from graphs
- * altosui: Add main/drogue voltages to default graph
- * altosui: Remove debug printf.
- * altosui: Compress telemetry records marked with the same time
- * altos: Shrink ao_cmd_put16, ao_cmd_hex and ao_cmd
- * altos: Shrink ao_config_callsign_set
- * altos: Shrink ao_add_task by rolling up a memset loop
- * altos: Switch ao_gps_skytraq and ao_gps_sirf __xdata to __pdata
- * altos: Switch ao_ignite and ao_gps_sirf __xdata to __pdata
- * altos: Switch ao_log.c and ao_log_big.c __xdata to __pdata
- * altos: Switch ao_report.c __xdata to __pdata
- * altos: Switch ao_rssi.c __xdata to __pdata
- * altos: Switch ao_sample.c __xdata to __pdata
- * altos: Switch ao_serial.c __xdata to __pdata
- * altos: Switch ao_stdio.c __data to __pdata
- * altos: Switch ao_telemetry.c __xdata to __pdata
- * altos: Switch ao_usb.c __xdata to __pdata
- * altos: Switch const for __code in struct ao_cmds
- * altos: switch ao_cmd __xdata to __pdata
- * altos: Switch ao_config.c __xdata to __pdata
- * altos: Switch ao_dbg.c __xdata to __pdata
- * altos: Switch ao_flight and ao_flight_nano __xdata to __pdata
- * altos: Switch flash drivers __xdata to __pdata
- * altos: Switch Tm and Tn to common telemetry code
- * altos: Remove ao_telemetry_orig.c and ao_telemetry_tiny.c
- * altos: Ensure low-rate telem packets interleave with sensor telem packets
- * altos: product defines are always in ao_product.h
- * altosui: Build device constants into .java code
- * altosui: Don't show missing igniter and gps values
- * altos: new versions of sdcc require __ prefixes for custom keywords
- * Set version to 0.9.4.3 for Bdale 2011-7-16 flights
- * altosui: Start adding support for scanning radio for available devices
- * altosui: Pop up monitor window from scan dialog
- * altosui: Remove debugging printf from AltosLog
- * altosui: Configuration telemetry record includes flight number
- * altosui: Finish radio scanning UI
- * altosui: Generalize and centralize telemetry constants, parse v0.8 telemetry
- * altosui: Initialize channel and telemetry before use in ScanUI
- * altosui: Set 'seen' bits in legacy telemetry packet reader
- * altosui: Add map preloading GUI
- * altosui: Try to avoid resize weirdness with map preloading
- * altosui: Flush telemetry lines before starting to watch for scan results
- * altosui: Display full map preload area in view.
- * altosui: Remove a bunch of sitemap debugging printfs
-
- [ Anthony Towns ]
- * altosui: Make sure degree and minute values are visible (map preload)
-
- [ Keith Packard ]
- * Set version to 0.9.4.4
- * altos, altosui: Add igniter mode (dual, apogee, main)
- * altosui: Download list of site locations for map preloading
- * altosui: Add launch-sites.txt
- * altosui: Add a bunch more site locations
- * altosui: Mark preload site location with red circles (like launch)
- * Fix NCR Pawnee location
- * Add HARA Bragg Farms site
- * altosui: Change continutity colors to yellow/magenta
- * altos: Add ability to read new TELEM files to ao_flight_test
- * altos: Average height values for landing detection
- * altos: Reduce height averaging filter time constant
- * altos: Require sequencing through 'main' state before landing
- * altosui: Standard text field in flight UI needs more width (now 20)
- * altosui: Parse accel cal from 'c s' command
- * altosui: Simple timeouts don't work with query data
- * altosui: Add idle monitor dialog
- * altos/altosui: Add pad orientation configure option
-
- [ Bdale Garbee ]
- * update version for a Bdale build for use turning on TeleMini v1.0
- * simplify version in last changelog entry so git-dch is less confused
- * update changelogs for Debian build
- * update changelogs for Debian build
- * stop doing automatic tag push during builds
- * build depend on bluetooth dev package
- * clean up all existing lintian warnings
- * rewind changelog for re-build of 0.9.4.5
-
- -- Bdale Garbee <bdale@gag.com> Mon, 08 Aug 2011 09:37:04 -0600
-
-altos (0.9.1) unstable; urgency=low
-
- [ Keith Packard ]
- * ao-load: fix usage message to note that '=' is required for options
- * altos/test: Add dependencies in the Makefile for ao_flight_test
- * altos/test: auto-configure acceleration parameters from the log file
-
- [ Anthony Towns ]
- * ao_radio: generalise setup of packet size
- * src/ao_gps_skytraq: simplify parsing code
- * src/ao_gps_skytraq.c: Update logging rate to 10Hz
-
- [ Bdale Garbee ]
- * tie bringup scripts to Bdale's bench TeleDongle
-
- -- Bdale Garbee <bdale@gag.com> Fri, 01 Apr 2011 20:02:12 -0600
-
-altos (0.9) unstable; urgency=low
-
- [ Bdale Garbee ]
- * prepare to release
- * update changelogs for Debian build
- * update turnon script to prefer TeleDongle as programmer
-
- [ Keith Packard ]
- * altos: Program default flight log max value for new boards
-
- -- Bdale Garbee <bdale@gag.com> Wed, 19 Jan 2011 12:46:47 -0700
-
-altos (0.8.1+81+g4ae724f) unstable; urgency=low
-
- * we need an install target to prevent parent dir make from failing
-
- -- Bdale Garbee <bdale@gag.com> Tue, 18 Jan 2011 23:55:36 -0700
-
-altos (0.8.1+79+g9a5666f) unstable; urgency=low
-
- [ Keith Packard ]
- * doc: Don't delete telemetrum-outline.pdf
- * doc: Add v0.9 features from altosui to documentation.
-
- [ Bdale Garbee ]
- * add 0.9 revision entry, with caveat about telemetry format change
- * freshen copyright year
-
- [ Keith Packard ]
- * fat: Add firmware for v1.1 and docs to mac/windows/linux installers
- * fat: Add docs to Linux package
- * doc: Build with 'make all' from top level. Build with 'make fat'
-
- -- Bdale Garbee <bdale@gag.com> Tue, 18 Jan 2011 23:47:52 -0700
-
-altos (0.8.1+71+gda42f40) unstable; urgency=low
-
- [ Keith Packard ]
- * doc: Add telemetrum mounting template in svg and pdf forms
-
- [ Mike Beattie ]
- * Re-order and re-arrange eeprom download dialog
- * Convert EepromSelect dialog to use a GridBag
- * Close serial port if Download/Delete dialog is cancelled.
-
- [ Keith Packard ]
- * altosui: Reset eeprom download instance variables before reading
- flight
- * altosui: Make serial debug more complete and accurate
- * altosui: Use long input flush timeout when remote.
- * altosui: Remove debug message when eeprom downloads are complete.
- * altosui: Ensure serial device is closed after eeprom download
- finishes
- * altosui: Require 4 sats to light up the 'GPS locked' light.
- * doc: inkscape tracks the filename inside the document
- * altos: TELEMETRY PROTOCOL CHANGE. Switch to 16-bit serial numbers.
- * altos: Flush log when full
-
- [ Anthony Towns ]
- * altos: Restructure skytraq NMEA parsing code to save some space
-
- [ Keith Packard ]
- * altos: average 512 accel/baro samples at startup instead of 1000
-
- [ Mike Beattie ]
- * altos: Added check for an accel value above 1.5g
- * altos: Added check for out of bounds accel
-
- [ Keith Packard ]
- * altos: Add DATA_TO_XDATA to linux test harness
- * altosui: Remove spurious colons from eeprom selection headers
-
- [ Mike Beattie ]
- * Rework invalid accel cal detection code
-
- [ Keith Packard ]
- * altos: Auto-calibrate linux-based flight testing code
- * altos: Ensure flight code gets first crack at new ADC data
- * altos: Sample the accelerometer reference voltage on v1.1 boards
- * altos: Optimize fetching of ADC data in flight code
- * altos: Use 5V reference data to correct accelerometer measurements.
- * doc: Remove mention of ao_wake_task
-
- [ Bdale Garbee ]
- * update documentation to reflect reality that modifying a board for
- separate pyro battery is not trivial
-
- -- Bdale Garbee <bdale@gag.com> Tue, 18 Jan 2011 17:26:33 -0700
-
-altos (0.8.1+42+g646e192) unstable; urgency=low
-
- [ Keith Packard ]
- * altosui: Show dialog after successful delete or when no flights
- * altosui: Ensure serial line is flushed after disabling remote link
- * altosui: Add preference for serial debugging.
-
- -- Bdale Garbee <bdale@gag.com> Fri, 14 Jan 2011 18:00:51 -0700
-
-altos (0.8.1+37+g97b1ca9) unstable; urgency=low
-
- [ Keith Packard ]
- * altos: Add configuration parameter for maximum flight log size
- * altos: support storage of multiple flights.
- * altos: Speed up at45 and 25lc erase speeds
- * altos: white space fix
- * altos: report flight log offsets in hex block numbers instead of
- bytes
- * altos: ensure erase mark is written when erasing flights
-
- [ Anthony Towns ]
- * altos: Optimize Morse code generation
-
- [ Keith Packard ]
- * altos: Check requested log max size against available space
- * altos: Check for full log and complain
- * altosui: Add configuration of flight log size
-
- [ Anthony Towns ]
- * altos: Remove unused accel_vel_mach and accel_vel_boost variables
- * altos: Remove redundant initialization of ao_interval variables
-
- [ Keith Packard ]
- * altosui: Split eeprom download code apart
- * altos: oops -- 'e' command was only showing 7 of the 8 bytes per
- line
- * altosui: Add support for parsing list of flights from the 'l'
- command
- * altosui: Add eeprom 'manage' ui to download and delete multiple
- flights
- * altos: check for valid flight number in ao_log_delete
-
- -- Bdale Garbee <bdale@gag.com> Fri, 14 Jan 2011 14:30:37 -0700
-
-altos (0.8.1+18+g408a3e0) unstable; urgency=low
-
- [ Anthony Towns ]
- * altosui: move maps to subdir, fix E/W mismatch
-
- [ Keith Packard ]
- * altos: clean up radio abort paths. Share radio code.
- * altos: eliminate ao_wake_task
- * windows: Add compatibility IDs to telemetrum.inf
- * windows: Update NSIS installer file to use compatibility IDs
- * altos: Split out SPI driver.
- * altos: Add telemetrum-v1.1 directory
- * altos: packet and usb i/o routines use 'char', not 'uint8_t'
- * altos: Simplify storage API
- * altos: Require manual flight erasing.
- * altos: Move common storage code to ao_storage.c. Add M25P80 driver
- * altos: Rip out 'optimization' in ao_log_scan
- * altos: Mark end of available flight list with 'done' to make the UI
-
- -- Bdale Garbee <bdale@gag.com> Fri, 07 Jan 2011 00:51:41 -0700
-
-altos (0.8.1+4+gea95c06) unstable; urgency=low
-
- * fix symlink paths in rules file
-
- -- Bdale Garbee <bdale@gag.com> Wed, 01 Dec 2010 00:14:24 -0700
-
-altos (0.8.1+2+gea7130e) unstable; urgency=low
-
- * modify Debian package build to deliver one copy of background.png
- for
-
- -- Bdale Garbee <bdale@gag.com> Wed, 01 Dec 2010 00:03:14 -0700
-
-altos (0.8.1) unstable; urgency=low
-
- [ Bdale Garbee ]
- * moved doc dir in web content to AltOS tree
- * fix publish target in doc/Makefile
- * fix section layering
- * fix an Altos vs Altus typo in the docs
- * adding Bdale's release process document to the source tree
-
- [ Keith Packard ]
- * windows: Add jfreechart.jar and jcommon.jar to windows install image
- * Move "Releasing" to top level
- * Add minimal release testing plan to Releasing
-
- [ Bdale Garbee ]
- * releasing 0.8.1
-
- -- Bdale Garbee <bdale@gag.com> Mon, 29 Nov 2010 21:46:54 -0700
-
-altos (0.8) unstable; urgency=low
-
- [ Keith Packard ]
- * altosui: Correct windows hardware IDs for nsis installer file
- * windows: try harder to get windows install to work
- * windows: remove some non-existent .inf file section references
- * windows: more .inf file hacking
- * windows: Bump .inf file version
-
- [ Bdale Garbee ]
- * declaring 0.8 released
- * update changelogs for Debian build
- * update changelogs for Debian build
- * rewind changelog to recover from stupid build failure
-
- -- Bdale Garbee <bdale@gag.com> Sun, 28 Nov 2010 18:32:12 -0700
-
-altos (0.7.1+168+gcb08bc2) unstable; urgency=low
-
- [ Keith Packard ]
- * altosui: Split out flight monitoring to separate window
- * altosui: Create buttons for main actions
- * altosui: Fix channel setting at serial open time
- * altosui: Fix more calls to AltosPreferences.channel()
- * altosui: Create abstract interface for flight data display
- * altosui: Add tab UI with 'pad' mode.
- * altosui: Add ascent, descent and landed tabs
-
- [ Bob Finch ]
- * Updated PKGBUILD-git.altos
-
- [ Keith Packard ]
- * altos: Use grey leds when unlit - easier to see
-
- [ Anthony Towns ]
- * use value_font for values
- * add --replay command line argument
- * read preferences for --replay
- * reduce font size for FlightInfoTable
- * use grayled.png for off
- * add compass bearing to voice output
- * add compass bearing during descent
- * add site map tab, at least for QRS launches
- * tabs -> spaces
- * make infotable scrollable, revert its fontsize to 14
- * pull up maps for arbitrary locations
- * better error behaviour if no map
-
- [ Bdale Garbee ]
- * first cut at instructions on how to re-flash TM and TD devices based
- on email
- * fold in content from Keith's email on the re-flashing subject
-
- [ Keith Packard ]
- * altosui: Add RF calibration to TeleMetrum config dialog
-
- [ Anthony Towns ]
- * AltosTelemetryReader: actually open serial port
- * AltosSiteMap: add targeting circles around landing site
-
- [ Bdale Garbee ]
- * continuing to work on the docs
-
- [ Keith Packard ]
- * altosui: Eliminate unncessary import altosui lines
- * altosui: Open serial device at 'new' time. Prohibit duplicate opens.
- * altosui: Replace flight status table with labels, fix resize.
- * altosui: With --replay option, exit when replay window is closed
- * altosui: oops, missed a file in the previous commit
- * altosui: eliminate menu bar, moving elements to buttons.
- * altosui: add reboot button to telemetrum configuration UI
-
- [ Bdale Garbee ]
- * add a paragraph about forcing TM back to idle mode if an accel cal
- goes badly
-
- [ Keith Packard ]
- * altosui: Add callsign configuration in AltosUI configuration dialog
- * altosui: Cleanup flight UI layout
- * altosui: Add igniter status to ascent and descent tabs
-
- [ Anthony Towns ]
- * altosui: tile site maps
- * AltosSiteMapTile: autoscale to about 2 nmi per tile
- * AltosSiteMapTile: adjust centering calculation
- * AltosSiteMapTile: adjust scale to 1 nmi per tile
-
- [ Keith Packard ]
- * altosui: Add igniter ground testing code
- * altosui: Unify datafile selection to AltosDataChooser
- * altosui: Clean up global AltosUI configuration settings dialog
- * doc: Add preliminary altosui documentation
- * doc: git ignore generated doc files
- * doc: Document the 'Flash Image' operation.
- * altosui: Use timeouts to recover from broken packet links.
-
- [ Bdale Garbee ]
- * update turnon scripts to use stashed copies of stable release
- firmware
-
- [ Keith Packard ]
- * altosui: switch channel selector to combo box. Shorten displayed
- device names
- * altosui: When switching log files, don't terminate log thread
- * altosui: calling thread.interrupt with null thread doesn't work well
- * altosui: Initialize display thread state in constructor instead of
- run
- * altosui: Fix channel changing in flight UI to actually work
-
- [ Anthony Towns ]
- * AltosSiteMap: add autoscroll and grabndrag scroll
- * AltosSiteMapTile: seperate map and drawing layers
- * AltosSiteMap: automatic fetching of map data
- * AltosSiteMapTile: draw boost circle as well as landed
- * AltosAscent/Descent: tidy up layout
- * AltosDescent: switch elev from height to range
-
- [ Keith Packard ]
- * altosui: re-indent
-
- [ Anthony Towns ]
- * AltosSiteMap: major refactoring
- * Add GrabNDrag.java
-
- [ Keith Packard ]
- * altosui: change descent tab formatting to four columns
-
- [ Anthony Towns ]
- * AltosSiteMap: be more polite about preferred size
- * altosui: reindent
-
- [ Keith Packard ]
- * altosui: Rewrite info table to mix with scroll pane well. Fix
- startup size
-
- [ Anthony Towns ]
- * AltosSiteMap: better gps check, lower zoom
-
- [ Keith Packard ]
- * altosui: Set site map flight path lines to 6 pixels anti-aliased.
-
- [ Anthony Towns ]
- * AltosSiteMap: explain tile size better
- * AltosSiteMap: extend map if rocket goes far away
- * AltosSiteMap: try to get new tile construction right
- * AltosSiteMap: thread safe tile addition
- * AltosSiteMap: refactor tile collection
- * AltosSiteMap: never accept 0,0 as lat/long
- * AltosSiteMap: limit nr of tiles to 200x200
-
- [ Keith Packard ]
- * altosui: When fixing eeprom gps time information, make GPS data
- valid
-
- [ Anthony Towns ]
- * AltosSiteMap: ensure buffer around active tile
- * altosui: improve sitemap scrolling behaviour
- * altosui: keep sitemap more centred on rocket
-
- [ Keith Packard ]
- * altos: Add on/off modes to 'C' command
-
- [ Bob Finch ]
- * Added PKGBUILDs for deps into contribs
-
- [ Keith Packard ]
- * altosui: Close serial port when debug link fails
- * altos: assume igniter worked.
-
- [ Bdale Garbee ]
- * add a rudimentary --help for command line use
-
- [ Keith Packard ]
- * doc: Add internal documentation for AltOS
-
- [ Anthony Towns ]
- * altosui: don't switch away from user selected tab
- * altosui: sitemap uses rocket gps if no pad gps
-
- [ Bdale Garbee ]
- * merge Keith's AltosUI documention into "the big book"
- * lose the placeholder on how GPS works, as it's going to be a
-
- [ Keith Packard ]
- * altos: remove unused variable from ao_igniter
- * altos: Don't abort radio transmissions with ao_radio_abort
- * altos: Make radio test command careful with the radio mutex.
- * altosui: Make AltosSerial.flush_input keep reading while non-empty
- * altosui: New AltosSerial.set_radio function sets channel/call
- * altosui: Disable radio configation over packet link.
- * altosui: Let people fire igniters that don't read as 'ready'
- * altosui: Make sure packet mode is turned off when the connection
- fails
-
- [ Anthony Towns ]
- * docs: Document altosui "Graph Data" button
-
- [ Keith Packard ]
- * Move altosui to the top level, placing libaltos inside it.
-
- [ Anthony Towns ]
- * doc: Document altosui "Site Map" tab
-
- [ Keith Packard ]
- * Missing change to top level Makefile to build altosui
-
- [ Bdale Garbee ]
- * fix missing section close in Site Map content
- * tweak rev history
- * manually fold in documentation work from the master branch
-
- [ Keith Packard ]
- * doc: Reformat altos to use sections for each function
- * doc: Add more authors, fix URL formatting, note that AltosUI
- actually exists
- * doc: Rename telemetrum-doc as altusmetrum
-
- [ Bdale Garbee ]
-
- -- Bdale Garbee <bdale@gag.com> Thu, 25 Nov 2010 01:10:18 -0700
-
-altos (0.7.1+36+g811ced6) unstable; urgency=low
-
- [ Bdale Garbee ]
- * remove the csv build dep, as that code will be abandoned
-
- [ Keith Packard ]
- * altosui: Remove ability to graph data in .csv files
- * altosui: Separate out jfreechart and jcommon directories
-
- -- Bdale Garbee <bdale@gag.com> Wed, 06 Oct 2010 17:47:32 -0600
-
-altos (0.7.1+32+g8103432) unstable; urgency=low
-
- * add build-dep on libcsv-java
-
- -- Bdale Garbee <bdale@gag.com> Wed, 06 Oct 2010 16:25:57 -0600
-
-altos (0.7.1+28+gd8a2f4c) unstable; urgency=low
-
- [ Bdale Garbee ]
- * make the column headers comma separated, too, so they align with the
- data
-
- [ Keith Packard ]
- * altosui: set default .csv file name in file save dialog
- * altosui: Remember directory containing firmware files
-
- [ Anthony Towns ]
- * Add graphing.
- * Add JFreeChart to Makefile.am
-
- [ Keith Packard ]
- * altosui: Use recorded ground acceleration when reading eeprom files
- * altosui: Write raw sensor data to .csv files
- * altosui: Factor some UI elements into separate classes
- * altosui: remove unused ReplayThread wrapper classes
- * altosui: Require 4 sats for 'good' GPS data
- * altosui: Create iterables for log file scanning. Split out display
- threads
- * altosui: .CSV output: add link quality, gps hdop and sat C/N0
- numbers
- * altosui: Deal with eeprom dates going backwards across wrap
-
- [ Anthony Towns ]
- * Hax0r graphing to support telem/eeprom files
-
- [ Keith Packard ]
- * altosui: use Altos constants in graphing code
-
- [ Anthony Towns ]
- * Add callsign/serial/flight to graph title
-
- [ Keith Packard ]
- * altosui: Add KML file export.
-
- [ Bdale Garbee ]
- * add build dep on jfreechart lib
-
- -- Bdale Garbee <bdale@gag.com> Wed, 06 Oct 2010 16:19:12 -0600
-
-altos (0.7.1) unstable; urgency=low
-
- [ Keith Packard ]
- * Add firmware and libaltos to 'fat' target at top-level
- * altosui: Remove some debug printfs.
- * altosui: libaltos.so is built with libtool -- it's in
- ../libaltos/.libs
- * Add --with-fat-dir configure option to publish finished stand-alone
- bits
- * altosui: Fix telemetry file reader to handle tick count wrapping
- * altosui: Remove debug printfs from AltosTelemetryReader
- * altosui: Fill in time value of last Eeprom record read from file
- * altosui: Stop parsing eeprom file after hitting 'landed' state
-
- -- Bdale Garbee <bdale@gag.com> Fri, 10 Sep 2010 00:09:02 -0600
-
-altos (0.7+96+g48f5799) unstable; urgency=low
-
- [ Keith Packard ]
- * altosui: conflating USB product and vendor IDs is a bad idea
-
- -- Bdale Garbee <bdale@gag.com> Thu, 09 Sep 2010 21:29:13 -0600
-
-altos (0.7+94+g1ac3d7e) unstable; urgency=low
-
- * initial cut at an altosui man page
-
- -- Bdale Garbee <bdale@gag.com> Thu, 09 Sep 2010 20:34:38 -0600
-
-altos (0.7+92+g0ea7576) unstable; urgency=low
-
- [ Bdale Garbee ]
- * handle versioning of ihx files (poorly) by just wildcarding the file
- name
-
- [ Keith Packard ]
- * altosui: Need to have JVM include path substituted into libaltos
- Makefile
- * altosui: Store libaltos.so in $(libdir)/altos
- * altosui: Display error dialog when AltOS JNI library can't be loaded
-
- -- Bdale Garbee <bdale@gag.com> Thu, 09 Sep 2010 20:05:44 -0600
-
-altos (0.7+86+g6c0ae7e) unstable; urgency=low
-
- [ Keith Packard ]
- * altosui: Add explicit requirement to create classes directory
- * altosui: fix telemetrum.inf FFFE:000A product names on AMD64 and
- ia64
- * altosui: hack to make JAVAROOT directory get created before javac
- runs
- * altosui: remove FATJAR from all-local to avoid building fat .jar
- file
-
- [ Bdale Garbee ]
- * add libtool to build deps
-
- [ Keith Packard ]
- * altosui: Add windows installer build using 'nsis'
- * altosui: ignore built files
- * altosui: oops. renamed the nsis file to altos-windows.nsi
- * icon: add some icons for application programs
- * altosui: Add icons to application and Windows menus.
- * Use autotools for altosui and libaltos
- * altos: add some SDCDB config files
- * Ignore libtool files.
- * Add version numbers to released files. Set version to 0.7.1
- * Add top-level 'fat' target to aid building distribution files
- * altosui: Fix windows installer to ship correct files
- * altosui: Fix up Mac OSX .zip file
- * altosui: Fix linux fat distribution
- * altosui: Return AO_LOG_INVALID instead of exception for eeprom files
- * altosui: Remove debugging printf from AltosEepromReader
- * altosui: Eeprom files contain only one date; save it.
- * altosui: Add elevation and range data to main display
- * altosui: When replay thread is interrupted, don't make final report
- * altosui: Start idle thread after the rocket leaves the pad
- * altosui: Add AltosVoice.drain() to wait for queued speech to finish
- * altosui: Prevent voice altitude data from queueing up
- * altosui: Use local .class files in the classpath
- * altosui: Record flight number when scanning file, not when running
- * altosui: eeprom files place 'boost' time in the flight number
- record.
- * altosui: ensure that 'altosui' script is installed. Pass arguments
- along.
-
- -- Bdale Garbee <bdale@gag.com> Thu, 09 Sep 2010 15:43:28 -0600
-
-altos (0.7+53+g59798c6) unstable; urgency=low
-
- [ Keith Packard ]
- * altosui: Abort flashing if debug port isn't working
- * altosui: allow flashing to be canceled from the rom config dialog
- * altosui: Hide internal rom config UI helper function
- * altosui: Remove some debug printfs from AltosRomconfig class
- * altosui: Post error dialog on invalid ROM config values.
- * altosui: build Mac OS .zip file to include paths
- * altosui: Report telemetry CRC errors in UI
- * altosui: Deal with altos bug setting radio channel while monitoring
- * altosui: Allow 'connect to device' when already connected
- * Revert "altosui: Deal with altos bug setting radio channel while
- monitoring"
- * altosui: Must flush serial line after configuring for telemetry
- * altosui: Catch I/O errors on telemetry device, report to user
-
- -- Bdale Garbee <bdale@gag.com> Sat, 04 Sep 2010 00:46:12 -0400
-
-altos (0.7+40+g59a40f6) unstable; urgency=low
-
- [ Bdale Garbee ]
- * add distclean targets to libaltos and altosui to all Debian package
- to build, and clean up other distclean content as needed
-
- [ Keith Packard ]
- * altosui: missed AltosReader.class in the Makefile
- * altos: Bounds check Skytraq GPS tracking data array
- * altosui: Remove Manifest.txt from git repo as it's built now
-
- -- Bdale Garbee <bdale@gag.com> Thu, 02 Sep 2010 00:44:15 -0400
-
-altos (0.7+28+gd006c5e) unstable; urgency=low
-
- * add runtime dependencies for altos binary package
-
- -- Bdale Garbee <bdale@gag.com> Tue, 31 Aug 2010 00:20:00 -0400
-
-altos (0.7+26+gc35632e) unstable; urgency=low
-
- * don't build all the "fat" jar deliverables by default
-
- -- Bdale Garbee <bdale@gag.com> Mon, 30 Aug 2010 19:37:40 -0600
-
-altos (0.7+23+g25764fc) unstable; urgency=low
-
- [ Bdale Garbee ]
- * fix up for an 0.7 release
- * update changelogs for Debian build
-
- [ Keith Packard ]
- * libaltos: AltusMetrum devices use more than one USB ID.
- * altosui: provide separate flush_input/flush_output for serial. deal
- with monitor automatically
- * altosui: discard invalid lines while reading Eeprom flight data
- * libaltos: Mac OS X cannot use 'poll(2)' on serial lines.
- * libaltos: Missing OS_LDFLAGS on cjnitest build
- * libaltos: cjnitest needs altos_flush now
- * altos: flush pending output when terminating packet mode
- * altos: Abort radio harder when terminating packet mode.
- * altos: shut down packet mode cleanly
- * libaltos: Fix windows build.
- * libaltos: Improve Makefile
- * Update telemetrum.inf to include all current USB ids.
- * libaltos: Add pre-built Mac OS X libaltos.dylib
- * libaltos: Add pre-built Windows .dll
- * altos: Windows sends USB Out packets of 0 length. Ack them.
- * libaltos: Use overlapped I/O on windows
- * altosui: Build linux, mac and windows archives on Linux
- * altosui: build debian-style altosui too
- * altosui: Devices with USB id 0x000a always get listed
-
- [ Bdale Garbee ]
- * continue even if rm's don't have anything to do
- * make invocation of 'install' pathless to work on more Unix variants
- * add a .gitattributes file, configuring the Mac and Windows binary
- library
-
- -- Bdale Garbee <bdale@gag.com> Mon, 30 Aug 2010 19:07:13 -0600
-
-altos (0.7) unstable; urgency=low
-
- * update changelogs for Debian build
- * fix up for an 0.7 release
-
- -- Bdale Garbee <bdale@gag.com> Fri, 27 Aug 2010 22:25:38 -0600
-
-altos (0.6+375+g0bd4cc0) unstable; urgency=low
-
- * fix path to installed shared library
-
- -- Bdale Garbee <bdale@gag.com> Fri, 27 Aug 2010 13:13:14 -0600
-
-altos (0.6+373+gcf65c6b) unstable; urgency=low
-
- [ Keith Packard ]
- * altosui: rename AltosEeprom -> AltosEepromDownload, split out Altos
- constants
- * altosui: Capture config and version info in .eeprom files
- * altosui: Merge gps date and time classes into gps class
- * altosui: Clear displayed data rows as needed.
- * altosui: Split status and info panels into separate files
- * altosui: Explicitly initialize Altos class
- * altosui: Split flight record out of telemetry class
- * altosui: Compute flight state from eeprom data
- * altosui: Add comments to Eeprom reader
- * altos: add callsign to packet mode, increase payload to 64 bytes
- * altosui: Start adding code to write csv files from eeprom/telem
- files
- * ao-dumplog: add --channel option (for use with -R option)
- * libaltos: integrate Windows support.
- * altosui: Select devices by USB vendor/product ID.
- * altos: Define USB product ID in per-product Makefile.defs file
- * altosui: Make teledongle callsign configurable
- * altosui: Add TeleMetrum configuration
- * altosui: Set callsign when fetching eeprom data over the air
-
- [ Bdale Garbee ]
- * add freetts as a build dep
- * working on java packaging details
-
- [ Keith Packard ]
- * altosui: Add .ihx file reading code and stub out flashing UI
- * altosui: Add debug dongle API, split flash UI out
- * ao-dumplog: Fix --remote and --channel options to actually work
- * altosui: pad TM config dialog values to avoid clipping descenders
- * libaltos: use pipe to wake up getchar on close. use mutexes
- * altosui: Add lots more cc1111 debug interface functions
- * altosui: remove debug printf from AltosHexfile
- * altosui: flush serial output before waiting for reply
- * altosui: Remove debug printf from AltosRomconfig
- * altosui: Finish device programming code
- * altos: Place rom config variables in fixed location
- * altosui: make default Manifest look for built-in freetts
- * altosui: Separate out log file choosing dialog to share with CSV
- generator
- * altosui: refactor logfile chooser dialog to share more code
- * altosui: Add ability to create CSV file from telem or eeprom files
- * altosui: disable radio monitoring while using serial line for
- debugging
- * altosui: Delay mapping Flash UI until flashing actually starts
- * altosui: fetch existing romconfig for flashing
- * altosui: always display romconfig ui while flashing
- * altosui: write USB serial number string while flashing
- * altosui: flush replies from serial link when entering debug mode
- * altos: always rebuild ao_product.c to track git version
- * altos: print GPS state flags in GPS 'g' command
- * altos: mark gps date written only after it gets into eeprom
- * altosui: Move number parsing code to Altos general class
- * altosui: Add AltosGreatCircle constructors
- * altosui: add rssi and distance/dir from pad to CSV files
- * altosui: AltosEepromReader was mis-setting boost tick
- * altosui: Add support for old (version < 3) telemetry files
- * altosui: Serial line is in UTF-8 encoding. Deal with it.
- * altosui: When parsing saved telem files, errors shouldn't abort file
- * altosui: Remove debug printf from AltosState.java
- * altosui: command line args are converted to csv format
- * altos: prepare for sdcc 2.9.1
-
- [ Bdale Garbee ]
- * add a dummy install target
- * lose the prebuild hook for now while I'm fumbling
- * add install target for libaltos
- * add an install target for altosui
-
- [ Keith Packard ]
- * altosui: add elevation and range information
-
- [ Bdale Garbee ]
- * fix up the wrapper's path to the jar file
- * update Debian standards version
- * fix permissions on installed jar file, switch from ao-view to
- altosui in
- * install altosui man page
- * fix man page delivery path
- * Revert "lose the prebuild hook for now while I'm fumbling"
-
- -- Bdale Garbee <bdale@gag.com> Fri, 27 Aug 2010 12:40:04 -0600
-
-altos (0.6+303+gb6da90b) unstable; urgency=low
-
- * add freetts as a build dep
- * move to science menu
- * working on java packaging details
-
- -- Bdale Garbee <bdale@gag.com> Wed, 11 Aug 2010 22:11:28 -0400
-
-altos (0.6+292+g8fc261c) unstable; urgency=low
-
- * see if my new freetts package works
-
- -- Bdale Garbee <bdale@gag.com> Sat, 31 Jul 2010 10:55:21 -0600
-
-altos (0.6+290+g7877496) unstable; urgency=low
-
- [ Keith Packard ]
- * altosui: check for closed serial device before reading
- * altosui: Remove unnecessary freetts .jar files
- * altosui: Close serial, join reader thread, free altos_file
- * altosui: remove debug printf
- * libaltos: build with java src encoding UTF8
- * altosui: construct Darwin application directory
- * Add Mac OS X packaging bits
- * altosui: Switch eeprom extension back to .eeprom
- * Moved Mac OS packaging to altosui dir
- * altosui: remove option to install to alternate volume
- * Make altosui test script executable
-
- -- Bdale Garbee <bdale@gag.com> Thu, 29 Jul 2010 13:30:19 -0600
-
-altos (0.6+277+gd184819) unstable; urgency=low
-
- [ Bdale Garbee ]
- * fix text since TM only has one led to blink
- * add swig as a build dep
- * add a jdk to the build deps
-
- [ Keith Packard ]
- * When the EP0 IN buffer is full, don't panic, just skip sending
- another
- * Add libaltos which talks to USB connected altos devices
- * Switch AltosUI to libaltos for device access
- * Present list of altos devices in nice format
- * Re-enable freetts
- * Re-enable Linux support for altosui.
- * Darwin doesn't have strndup.
- * libaltos needs -I. on all systems
- * libaltos: make clean remove all built files
- * libaltos: build fat 10.5-compatible library
- * Add Mac OS X packaging files for altosui
- * Add application icons for Mac OS X
- * Clean up altosui build a bit
- * Remove directories as .class file dependencies; it makes them get
- rebuilt all the time
- * Java clean ups -- use varargs where possible, remove
- AltosSerialReader
- * Java voice reporting cleanups.
- * Force java source encoding to UTF-8
- * Make ao_log_data re-entrant as it is used for both sensor and GPS
- logs
- * altosui: Catch errors opening USB devices. Limit list to relevant
- devices
- * Make voice and channel menus work.
- * Add voice test command for help in adjusting volume.
- * Remove debug printf
- * altosui: Add eeprom data capture function. No UI yet.
- * altosui: Add progress bar for eeprom downloading status
- * altosui: Fix Save flight data monitor layout, add cancel
- * altosui: Replace device dialog. Center eeprom monitor.
- * altosui: report rocket ground bearing at landing only if known
- * Reset GPS ready status when GPS comes unlocked on the pad
-
- -- Bdale Garbee <bdale@gag.com> Thu, 29 Jul 2010 12:50:40 -0600
-
-altos (0.6+236+gcd8aa79) unstable; urgency=low
-
- [ Keith Packard ]
- * Telemetry code was mis-computing RSSI
- * Switch DBG pins to GPIO when using any debug commands. Reboot to
- restore.
-
- [ Bdale Garbee ]
- * significant documentation update
- * add build dep for sndfile
- * reflect documentation file name change
- * update to latest Debian standards version
-
- -- Bdale Garbee <bdale@gag.com> Tue, 20 Jul 2010 22:24:14 -0600
-
-altos (0.6+224+g4766b13) unstable; urgency=low
-
- [ Bdale Garbee ]
- * documentation updates from Bob
-
- [ Mike Beattie ]
- * Extension to KML output format, and minor bug fix
-
- [ Keith Packard ]
- * ao-view: disable radio telemetry monitoring during channel change
- * Add special code for USB panic's.
- * ao-postflight: was walking off state.data array
- * Abort any in-progress radio operation when changing radio channel
-
- -- Bdale Garbee <bdale@gag.com> Thu, 24 Jun 2010 12:37:34 -0700
-
-altos (0.6+214+g16c4cae) unstable; urgency=low
-
- [ Bdale Garbee ]
- * updates including a typo fix from Bob Finch to the PKGBUILD-git.altos
- * merge a derivative of Bob Finch's mere mortals guide as getting started
- * merge the altusmetrum-themes package
-
- [ Keith Packard ]
- * Fix telemetrum.inf, tested by Adrian and Keithp
- * Finish basic flight monitoring UI with voice using FreeTTS
-
- -- Bdale Garbee <bdale@gag.com> Tue, 18 May 2010 00:24:40 -0600
-
-altos (0.6+204+g6bd8513) unstable; urgency=low
-
- * lose the quotes since they apparently aren't necessary
-
- -- Bdale Garbee <bdale@gag.com> Wed, 12 May 2010 19:53:58 -0600
-
-altos (0.6+202+gae6854d) unstable; urgency=low
-
- * update desktop file for conformance with current standards
-
- -- Bdale Garbee <bdale@gag.com> Wed, 12 May 2010 17:04:31 -0600
-
-altos (0.6+200+g68eaaa6) unstable; urgency=low
-
- * add initial package build scripts for Arch Linux from Bob Finch
- * add desktop file provided by Bob Finch
-
- -- Bdale Garbee <bdale@gag.com> Wed, 12 May 2010 16:44:27 -0600
-
-altos (0.6+195+gcde60f1) unstable; urgency=low
-
- * Revert "Merge remote branch 'remotes/origin/fix-reset'"
-
- -- Bdale Garbee <bdale@gag.com> Thu, 06 May 2010 13:59:16 -0600
-
-altos (0.6+193+g314d27a) unstable; urgency=low
-
- [ Keith Packard ]
- * Don't change dbg clock while changing reset_n. Use 20ms everywhere
-
- -- Bdale Garbee <bdale@gag.com> Thu, 06 May 2010 12:47:51 -0600
-
-altos (0.6+190+g8b6767e) unstable; urgency=low
-
- [ Keith Packard ]
- * Fix all stdio reading functions to be __critical
- * Use ao_delay to sleep for 2 seconds instead of trying ao_sleep
-
- -- Bdale Garbee <bdale@gag.com> Wed, 05 May 2010 02:34:06 -0600
-
-altos (0.6+187+g8702f49) unstable; urgency=low
-
- [ Bdale Garbee ]
- * more text created during SFO->DEN flight
- * initial attempt at a telemetrum turn on script .. needs work
-
- [ Keith Packard ]
- * Revert "Add optional 's' command to packet slave to enable/disable
- slave mode"
- * Disable interrupts while reading from stdin
-
- -- Bdale Garbee <bdale@gag.com> Wed, 05 May 2010 01:52:27 -0600
-
-altos (0.6+180+g99094f0) unstable; urgency=low
-
- [ Keith Packard ]
- * Increase reset switch time to 100ms
- * Add optional 's' command to packet slave to enable/disable slave
- mode
- * More ALtosUI changes
- * Autodetect flite voice registration function
-
- [ Bdale Garbee ]
- * capture work done on SFO->DEN flight
- * add some RF usage information from an email reply sent today, and
- re-indent
-
- -- Bdale Garbee <bdale@gag.com> Tue, 27 Apr 2010 00:17:57 -0600
-
-altos (0.6+171+g9394393) unstable; urgency=low
-
- [ Bdale Garbee ]
- * wrong Yaesu model
-
- [ Keith Packard ]
- * Only have the slave return a packet if it received one.
-
- -- Bdale Garbee <bdale@gag.com> Sat, 10 Apr 2010 15:01:04 -0600
-
-altos (0.6+168+gc0ee1ae) unstable; urgency=low
-
- [ Bdale Garbee ]
- * INSTALL file changed by auto tools
-
- [ Keith Packard ]
- * libflite may forget to reference libasound
-
- -- Bdale Garbee <bdale@gag.com> Fri, 09 Apr 2010 00:08:24 -0600
-
-altos (0.6+164+g5c3b6e2) unstable; urgency=low
-
- [ Keith Packard ]
- * Start adding java-based UI
- * Add telemetry data parsing code
- * Add Windows install .inf file
- * Fix windows install file
- * Add telem parsing code
- * Steal C code from ao-view
- * Display table of flight info. gps is not working yet though
- * Fix up table formatting
- * Fix status update
- * Fix state updates
- * Clean up GPS data formatting
- * Report current gps nsat, not last locked nsat
- * Remove GPS data missing from skytraq. Save max height/accel/speed
- * Remove unused cell renderer class
- * Make .jar file
- * Use RXTX for serial comm. Add logdir preference saving
- * Make ao_radio_idle keep trying to get the radio to idle.
- * Don't abort the radio when enabling telemetry monitoring
- * Clean up some altosui comments
- * Switch TeleMetrum from v0.2 to v1.0
- * Add Linux device discovery
- * Interrupt running replay thread when starting another replay
- * serial port read function cannot be interrupted. poll every 1 second
- * TD reports "not-connected" when GPS has 0 sats
- * Tasks may move in task structure as a result of ao_exit
- * Enable telemetry monitoring
- * Use 16-bit flite voice (which appears to have changed symbols
- recently)
- * When changing RESET line, delay 20ms
-
- [ Bdale Garbee ]
- * choose a better set of docbook xsl files
-
- -- Bdale Garbee <bdale@gag.com> Thu, 08 Apr 2010 19:56:27 -0600
-
-altos (0.6+131+g6629ec5) unstable; urgency=low
-
- * lose the url entirely for now
-
- -- Bdale Garbee <bdale@gag.com> Thu, 08 Apr 2010 12:43:01 -0600
-
-altos (0.6+129+g934434f) unstable; urgency=low
-
- * fix typo in url
-
- -- Bdale Garbee <bdale@gag.com> Thu, 08 Apr 2010 12:41:38 -0600
-
-altos (0.6+127+g05ad583) unstable; urgency=low
-
- * need another build dep
-
- -- Bdale Garbee <bdale@gag.com> Thu, 08 Apr 2010 12:35:04 -0600
-
-altos (0.6+125+g8f1d47e) unstable; urgency=low
-
- * make lintian happy
- * tweak copyright assertion
- * crudely incorporate "day in the life" info from web page
- * rewrite urls in docbook format
-
- -- Bdale Garbee <bdale@gag.com> Thu, 08 Apr 2010 12:28:04 -0600
-
-altos (0.6+119+g00f49c8) unstable; urgency=low
-
- [ Bdale Garbee ]
- * update changelogs for Debian build
- * move gbp.conf into debian/
- * initial harness for documentation
- * fix typo
-
- [ Keith Packard ]
- * Round radio calibration value instead of truncating
- * Document the ao-dumplog '--remote' flag for radio-link downloads
-
- -- Bdale Garbee <bdale@gag.com> Tue, 30 Mar 2010 23:19:15 -0600
-
-altos (0.6+108+g6e61170) unstable; urgency=low
-
- [ Keith Packard ]
- * Need to duplicate new altitude conversion code in aoview.
-
- -- Bdale Garbee <bdale@gag.com> Thu, 04 Mar 2010 17:33:27 -0700
-
-altos (0.6+106+ga1478f6) unstable; urgency=low
-
- [ Keith Packard ]
- * Add ao_radio_xmit to help test boards without flashing them.
- * Allow product names to have suffixes (like board revisions)
- * Fix and document the ao-rawload --run flag
- * Add LED test
- * Leave .ihx files in the build directory too - easier to debug that way
- * Eliminate deadlock when writing config from radio link
- * Fix up LED colors for each product.
- * Add .gitignore for ao-bringup
-
- [ Bdale Garbee ]
- * create a turn on script for lighting up TeleDongle v0.2 boards
-
- -- Bdale Garbee <bdale@gag.com> Sat, 27 Feb 2010 17:35:32 -0700
-
-altos (0.6+95+g2f45953) unstable; urgency=low
-
- * update changelogs for Debian build
- * conditionalize use of git on executability of /usr/bin/git binary
-
- -- Bdale Garbee <bdale@gag.com> Wed, 24 Feb 2010 17:30:00 -0700
-
-altos (0.6+88+gdeccc10) unstable; urgency=low
-
- * add gawk as a build dependency since strtonum is a gawk extension
-
- -- Bdale Garbee <bdale@gag.com> Wed, 24 Feb 2010 16:44:35 -0700
-
-altos (0.6+86+g2491282) unstable; urgency=low
-
- [ Keith Packard ]
- * Disable monitor mode before attempting radio test.
- * Ensure that ao_alarm waits at least the specified time
- * Remove dbg driver code from telemetrum/teledongle
- * Add AT45DBxx1D driver
- * Remove green LED and temp sensor from v0.2 code
- * Add at45db161d.h header file for new flash part.
- * Add 'f' command to display flash status register contents
- * Dump more flash parameters for the flash_status command
- * Dump config block from read/write config and flash_status commands
- * Don't set ao_flash_setup_done until we're actually done.
- * Remove flash debugging printfs
- * Add simple gps dump command 'g'
- * Force idle mode by shorting the SPI clock to ground at boot time.
- * Switch to using internal cc1111 temperature sensor
- * Missing ao_mutex_put in gps_dump
- * Compute daytime using GPS as time base
- * Pull in a bit more data for filtering the start of the boost
- * Log GPS data on pad after boost detect.
- * Change barometer conversion code to shrink conversion table
- * Change altos build process to support per-product compile-time
- changes
- * Update .gitignore files
- * Quiet make output.
- * Add back stack size checking to altos linking phase
- * Must install .map files for ao-load to work
-
- -- Bdale Garbee <bdale@gag.com> Wed, 24 Feb 2010 14:53:01 -0700
-
-altos (0.6+60+g10d1bbc) unstable; urgency=low
-
- [ Keith Packard ]
- * Use ao_radio_get/ao_radio_put in packet code.
-
- -- Bdale Garbee <bdale@gag.com> Sat, 19 Dec 2009 13:53:32 -0700
-
-altos (0.6+58+gbbb152c) unstable; urgency=low
-
- [ Keith Packard ]
- * Re-order config values. Change frequency to cal
- * Allow radio calibration to be set from ao-load
- * Add --cal to man page
-
- -- Bdale Garbee <bdale@gag.com> Sat, 19 Dec 2009 12:05:26 -0700
-
-altos (0.6+53+gcd49847) unstable; urgency=low
-
- [ Keith Packard ]
- * Remove send_serial and serial_baud commands.
- * Make ao_cmd_decimal produce both 32 and 16 bit values.
- * Add radio calibration configuration.
-
- -- Bdale Garbee <bdale@gag.com> Sat, 05 Dec 2009 11:02:49 -0700
-
-altos (0.6+49+g9a1d7dd) unstable; urgency=low
-
- [ Keith Packard ]
- * Change default callsign to "N0CALL"
-
- -- Bdale Garbee <bdale@gag.com> Fri, 04 Dec 2009 21:01:55 -0700
-
-altos (0.6+47+g4053309) unstable; urgency=low
-
- * fix absolute path in debian/dirs, add Suggests for slim-altusmetrum
- * change home URL in control file to be the AltOS page
-
- -- Bdale Garbee <bdale@gag.com> Thu, 26 Nov 2009 11:15:47 -0700
-
-altos (0.6+43+gd6ba07e) unstable; urgency=low
-
- [ Keith Packard ]
- * Decode HDOP data from skytraq GPS
- * Document ao-postflight --gps and --kml options.
- * Make ao-postflight create filenames using input filenames.
- * Make TD print 0000-00-00 for invalid dates.
- * Fix --plot arg handling. Add -all option.
- * Convert telemetry file GPS satellite information in cc_log_read
- * Don't crash if --plot isn't passed on ao-postflight command line
- * ao-postflight: compute barometric alt for each GPS position
- * ao-postflight: don't try to use missing gps sat data
- * Automatically extract flight number for eeprom and telem filenames.
-
- -- Bdale Garbee <bdale@gag.com> Sun, 22 Nov 2009 10:18:26 -0700
-
-altos (0.6+32+g87e6f3e) unstable; urgency=low
-
- [ Bdale Garbee ]
- * fix typo in comment
-
- [ Keith Packard ]
- * Reduce igniter firing time from 500ms to 50ms.
- * Add GPS date/time output to ao-postflight.
- * Eliminate SiRF state values from ao-view.
-
- -- Bdale Garbee <bdale@gag.com> Fri, 20 Nov 2009 13:18:06 -0700
-
-altos (0.6+27+gb0d7e3f) unstable; urgency=low
-
- [ Keith Packard ]
- * Add two-point accelerometer calibration.
- * Remove "l" command as ao-dumplong no longer uses it
- * Remove "d" command
- * Remove "f" command
- * Reformat ADC values to show all 16 bits
- * ao_flight_test was using accel value for pressure too
- * Pass accel calibration over telemetry stream. Telemetry data format
- change.
- * Add ability to dump eeprom data over radio link.
- * In packet master, move USB flush from packet thread to echo thread
- * In USB pollchar, wait for packet before re-checking USB out len
- * Explicitly use USB I/O routines in packet code
- * Flush pending input when switching to remote packet mode
- * Stop recording in ao-dumplog after receiving an invalid block
- * Move ao_match_word from ao_ignite.c to ao_cmd.c
- * Add Watchdog Timer Control register definitions
- * Add reboot command.
- * Return radio to telemetry settings when packet system closed.
- * ao-postflight: fix sloppy gps sat data realloc code (was crashing).
- * Loosen tolerances for main->landed transition
- * Provide a dummy 'uninstall' target in the src directory.
- * Share telemetry parsing code in cc library.
- * Enable telemetry receive in ao_view
- * Switch order of serial/flight in ao-postflight summary
- * Add flight number to telemetry stream.
- * Add date to GPS data, captured from GPRMC packet.
- * Stop using SiRF state info.
-
- -- Bdale Garbee <bdale@gag.com> Fri, 20 Nov 2009 11:43:56 -0700
-
-altos (0.6) unstable; urgency=low
-
- [ Keith Packard ]
- * Add support for the SkyTraq GPS unit
- * Build two versions of TM, one for SiRF, one for SkyTraq
- * Save some DSEG space by marking cmd functions __reentrant
- * Add ao_wake_task and ao_exit
- * Add keyhole-markup generation for ao-postflight.
- * Initial packet bits. Just testing transmission
- * Add radio carrier command
- * Wait for TX to finish sending data
- * Add ao_alarm
- * Remove reason from ao_dma_abort
- * Switch packet code from timer thread to ao_alarm
- * Use ao_radio_done to wait for TX to completely finish with packet
- * Send SYN packet to set sequence numbers
- * Add RFIM register
- * Do more flushing in packet test code
- * Use ao_alarm for ao_delay so it can be easily interrupted
- * Poke master to speed up packet rate when things are busy
- * No need to wakeup &ao_tick_count now
- * Enable packet-based communcation to command processor
- * Add more docs to the README file
- * Disable interrupts while removing tasks from task list
- * Add ao_usb_pollchar to ao.h
-
- -- Bdale Garbee <bdale@gag.com> Mon, 02 Nov 2009 16:53:45 -0700
-
-altos (0.5+90+g127c312) unstable; urgency=low
-
- * de-version the libreadline-dev build dependency
-
- -- Bdale Garbee <bdale@gag.com> Mon, 02 Nov 2009 15:57:29 -0700
-
-altos (0.5+86+g2de548f) unstable; urgency=low
-
- * automate push of updated and tagged master branch during
- debian/rules prebuild
- * flush repetitive junk out of debian/changelog, and update the
- prebuild target
- * add support for tagging git repository on each Debian package build
-
- -- Bdale Garbee <bdale@gag.com> Mon, 12 Oct 2009 16:54:28 -0600
-
-altos (0.5+77+gc57bd7f) unstable; urgency=low
-
- * build for Debian from git
-
- -- Bdale Garbee <bdale@gag.com> Mon, 12 Oct 2009 15:57:19 -0600
-