-<?xml version="1.0" encoding="utf-8" ?>
+<?xml version="1.0" encoding="utf-8"?>
<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook XML V4.5//EN"
"/usr/share/xml/docbook/schema/dtd/4.5/docbookx.dtd">
<book>
<title>The Altus Metrum System</title>
- <subtitle>An Owner's Manual for TeleMetrum, TeleMini and TeleDongle Devices</subtitle>
+ <subtitle>An Owner's Manual for Altus Metrum Rocketry Electronics</subtitle>
<bookinfo>
<author>
<firstname>Bdale</firstname>
<surname>Towns</surname>
</author>
<copyright>
- <year>2011</year>
+ <year>2014</year>
<holder>Bdale Garbee and Keith Packard</holder>
</copyright>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="../themes/background.png" width="6.0in"/>
+ </imageobject>
+ </mediaobject>
<legalnotice>
<para>
This document is released under the terms of the
</para>
</legalnotice>
<revhistory>
+ <revision>
+ <revnumber>1.4.1</revnumber>
+ <date>20 June 2014</date>
+ <revremark>
+ Minor release fixing some installation bugs.
+ </revremark>
+ </revision>
+ <revision>
+ <revnumber>1.4</revnumber>
+ <date>15 June 2014</date>
+ <revremark>
+ Major release adding TeleGPS support.
+ </revremark>
+ </revision>
+ <revision>
+ <revnumber>1.3.2</revnumber>
+ <date>24 January 2014</date>
+ <revremark>
+ Bug fixes for TeleMega and AltosUI.
+ </revremark>
+ </revision>
+ <revision>
+ <revnumber>1.3.1</revnumber>
+ <date>21 January 2014</date>
+ <revremark>
+ Bug fixes for TeleMega and TeleMetrum v2.0 along with a few
+ small UI improvements.
+ </revremark>
+ </revision>
+ <revision>
+ <revnumber>1.3</revnumber>
+ <date>12 November 2013</date>
+ <revremark>
+ Updated for software version 1.3. Version 1.3 adds support
+ for TeleMega, TeleMetrum v2.0, TeleMini v2.0 and EasyMini
+ and fixes bugs in AltosUI and the AltOS firmware.
+ </revremark>
+ </revision>
+ <revision>
+ <revnumber>1.2.1</revnumber>
+ <date>21 May 2013</date>
+ <revremark>
+ Updated for software version 1.2. Version 1.2 adds support
+ for TeleBT and AltosDroid. It also adds a few minor features
+ and fixes bugs in AltosUI and the AltOS firmware.
+ </revremark>
+ </revision>
+ <revision>
+ <revnumber>1.2</revnumber>
+ <date>18 April 2013</date>
+ <revremark>
+ Updated for software version 1.2. Version 1.2 adds support
+ for MicroPeak and the MicroPeak USB interface.
+ </revremark>
+ </revision>
+ <revision>
+ <revnumber>1.1.1</revnumber>
+ <date>16 September 2012</date>
+ <revremark>
+ Updated for software version 1.1.1 Version 1.1.1 fixes a few
+ bugs found in version 1.1.
+ </revremark>
+ </revision>
+ <revision>
+ <revnumber>1.1</revnumber>
+ <date>13 September 2012</date>
+ <revremark>
+ Updated for software version 1.1. Version 1.1 has new
+ features but is otherwise compatible with version 1.0.
+ </revremark>
+ </revision>
<revision>
<revnumber>1.0</revnumber>
<date>24 August 2011</date>
</revision>
</revhistory>
</bookinfo>
- <acknowledgements>
+ <dedication>
+ <title>Acknowledgments</title>
<para>
- Thanks to Bob Finch, W9YA, NAR 12965, TRA 12350 for writing "The
+ Thanks to Bob Finch, W9YA, NAR 12965, TRA 12350 for writing “The
Mere-Mortals Quick Start/Usage Guide to the Altus Metrum Starter
- Kit" which formed the basis of the original Getting Started chapter
+ Kit” which formed the basis of the original Getting Started chapter
in this manual. Bob was one of our first customers for a production
TeleMetrum, and his continued enthusiasm and contributions
are immensely gratifying and highly appreciated!
NAR #88757, TRA #12200
</literallayout>
</para>
- </acknowledgements>
+ </dedication>
<chapter>
<title>Introduction and Overview</title>
<para>
<para>
The first device created for our community was TeleMetrum, a dual
deploy altimeter with fully integrated GPS and radio telemetry
- as standard features, and a "companion interface" that will
- support optional capabilities in the future.
+ as standard features, and a “companion interface” that will
+ support optional capabilities in the future. The latest version
+ of TeleMetrum, v2.0, has all of the same features but with
+ improved sensors and radio to offer increased performance.
</para>
<para>
- The newest device is TeleMini, a dual deploy altimeter with
- radio telemetry and radio direction finding. This device is only
- 13mm by 38mm (½ inch by 1½ inches) and can fit easily in an 18mm
- air-frame.
+ Our second device was TeleMini, a dual deploy altimeter with
+ radio telemetry and radio direction finding. The first version
+ of this device was only 13mm by 38mm (½ inch by 1½ inches) and
+ could fit easily in an 18mm air-frame. The latest version, v2.0,
+ includes a beeper, USB data download and extended on-board
+ flight logging, along with an improved barometric sensor.
</para>
<para>
- Complementing TeleMetrum and TeleMini is TeleDongle, a USB to RF
- interface for communicating with the altimeters. Combined with your
- choice of antenna and
- notebook computer, TeleDongle and our associated user interface software
- form a complete ground station capable of logging and displaying in-flight
- telemetry, aiding rocket recovery, then processing and archiving flight
+ TeleMega is our most sophisticated device, including six pyro
+ channels (four of which are fully programmable), integrated GPS,
+ integrated gyroscopes for staging/air-start inhibit and high
+ performance telemetry.
+ </para>
+ <para>
+ EasyMini is a dual-deploy altimeter with logging and built-in
+ USB data download.
+ </para>
+ <para>
+ TeleDongle was our first ground station, providing a USB to RF
+ interfaces for communicating with the altimeters. Combined with
+ your choice of antenna and notebook computer, TeleDongle and our
+ associated user interface software form a complete ground
+ station capable of logging and displaying in-flight telemetry,
+ aiding rocket recovery, then processing and archiving flight
data for analysis and review.
</para>
+ <para>
+ For a slightly more portable ground station experience that also
+ provides direct rocket recovery support, TeleBT offers flight
+ monitoring and data logging using a Bluetooth™ connection between
+ the receiver and an Android device that has the AltosDroid
+ application installed from the Google Play store.
+ </para>
<para>
More products will be added to the Altus Metrum family over time, and
we currently envision that this will be a single, comprehensive manual
<title>Getting Started</title>
<para>
The first thing to do after you check the inventory of parts in your
- "starter kit" is to charge the battery.
+ “starter kit” is to charge the battery.
</para>
<para>
- The TeleMetrum battery can be charged by plugging it into the
- corresponding socket of the TeleMetrum and then using the USB A to
- mini B
- cable to plug the TeleMetrum into your computer's USB socket. The
- TeleMetrum circuitry will charge the battery whenever it is plugged
- in, because the TeleMetrum's on-off switch does NOT control the
+ For TeleMetrum and TeleMega, the battery can be charged by plugging it into the
+ corresponding socket of the device and then using the USB
+ cable to plug the flight computer into your computer's USB socket. The
+ on-board circuitry will charge the battery whenever it is plugged
+ in, because the on-off switch does NOT control the
charging circuitry.
</para>
<para>
- When the GPS chip is initially searching for
- satellites, TeleMetrum will consume more current than it can pull
- from the USB port, so the battery must be attached in order to get
- satellite lock. Once GPS is locked, the current consumption goes back
- down enough to enable charging while
- running. So it's a good idea to fully charge the battery as your
- first item of business so there is no issue getting and maintaining
- satellite lock. The yellow charge indicator led will go out when the
- battery is nearly full and the charger goes to trickle charge. It
- can take several hours to fully recharge a deeply discharged battery.
+ On TeleMetrum v1 boards, when the GPS chip is initially
+ searching for satellites, TeleMetrum will consume more current
+ than it pulls from the USB port, so the battery must be
+ attached in order to get satellite lock. Once GPS is locked,
+ the current consumption goes back down enough to enable charging
+ while running. So it's a good idea to fully charge the battery
+ as your first item of business so there is no issue getting and
+ maintaining satellite lock. The yellow charge indicator led
+ will go out when the battery is nearly full and the charger goes
+ to trickle charge. It can take several hours to fully recharge a
+ deeply discharged battery.
+ </para>
+ <para>
+ TeleMetrum v2.0 and TeleMega use a higher power battery charger,
+ allowing them to charge the battery while running the board at
+ maximum power. When the battery is charging, or when the board
+ is consuming a lot of power, the red LED will be lit. When the
+ battery is fully charged, the green LED will be lit. When the
+ battery is damaged or missing, both LEDs will be lit, which
+ appears yellow.
+ </para>
+ <para>
+ The Lithium Polymer TeleMini and EasyMini battery can be charged by
+ disconnecting it from the board and plugging it into a
+ standalone battery charger such as the LipoCharger product
+ included in TeleMini Starter Kits, and connecting that via a USB
+ cable to a laptop or other USB power source.
</para>
<para>
- The TeleMini battery can be charged by disconnecting it from the
- TeleMini board and plugging it into a standalone battery charger
- board, and connecting that via a USB cable to a laptop or other USB
- power source
+ You can also choose to use another battery with TeleMini v2.0
+ and EasyMini, anything supplying between 4 and 12 volts should
+ work fine (like a standard 9V battery), but if you are planning
+ to fire pyro charges, ground testing is required to verify that
+ the battery supplies enough current to fire your chosen e-matches.
</para>
<para>
The other active device in the starter kit is the TeleDongle USB to
RF interface. If you plug it in to your Mac or Linux computer it should
- "just work", showing up as a serial port device. Windows systems need
+ “just work”, showing up as a serial port device. Windows systems need
driver information that is part of the AltOS download to know that the
existing USB modem driver will work. We therefore recommend installing
our software before plugging in TeleDongle if you are using a Windows
- computer. If you are using Linux and are having problems, try moving
- to a fresher kernel (2.6.33 or newer), as the USB serial driver had
- ugly bugs in some earlier versions.
+ computer. If you are using an older version of Linux and are having
+ problems, try moving to a fresher kernel (2.6.33 or newer).
</para>
<para>
- Next you should obtain and install the AltOS software. These include
- the AltosUI ground station program, current firmware images for
- TeleMetrum, TeleMini and TeleDongle, and a number of standalone
- utilities that are rarely needed. Pre-built binary packages are
- available for Linux, Microsoft Windows, and recent MacOSX versions.
- Full source code and build instructions are also available.
- The latest version may always be downloaded from
+ Next you should obtain and install the AltOS software. The AltOS
+ distribution includes the AltosUI ground station program, current
+ firmware
+ images for all of the hardware, and a number of standalone
+ utilities that are rarely needed. Pre-built binary packages are
+ available for Linux, Microsoft Windows, and recent MacOSX
+ versions. Full source code and build instructions are also
+ available. The latest version may always be downloaded from
<ulink url="http://altusmetrum.org/AltOS"/>.
</para>
+ <para>
+ If you're using a TeleBT instead of the TeleDongle, you'll want to
+ install the AltosDroid application from the Google Play store on an
+ Android device. You don't need a data plan to use AltosDroid, but
+ without network access, the Map view will be less useful as it
+ won't contain any map data. You can also use TeleBT connected
+ over USB with your laptop computer; it acts exactly like a
+ TeleDongle. Anywhere this manual talks about TeleDongle, you can
+ also read that as 'and TeleBT when connected via USB'.
+ </para>
</chapter>
<chapter>
<title>Handling Precautions</title>
strapping them down, for example.
</para>
<para>
- The barometric sensors used on both TeleMetrum and TeleMini are
- sensitive to sunlight. In normal TeleMetrum mounting situations, it
+ The barometric sensors used on all of our flight computers are
+ sensitive to sunlight. In normal mounting situations, the baro sensor
and all of the other surface mount components
- are "down" towards whatever the underlying mounting surface is, so
- this is not normally a problem. Please consider this, though, when
- designing an installation, for example, in an air-frame with a
- see-through plastic payload bay. It is particularly important to
- consider this with TeleMini, both because the baro sensor is on the
- "top" of the board, and because many model rockets with payload bays
+ are “down” towards whatever the underlying mounting surface is, so
+ this is not normally a problem. Please consider this when designing an
+ installation in an air-frame with a see-through plastic payload bay. It
+ is particularly important to
+ consider this with TeleMini v1.0, both because the baro sensor is on the
+ “top” of the board, and because many model rockets with payload bays
use clear plastic for the payload bay! Replacing these with an opaque
cardboard tube, painting them, or wrapping them with a layer of masking
tape are all reasonable approaches to keep the sensor out of direct
sunlight.
</para>
<para>
- The barometric sensor sampling port must be able to "breathe",
+ The barometric sensor sampling port must be able to “breathe”,
both by not being covered by foam or tape or other materials that might
directly block the hole on the top of the sensor, and also by having a
suitable static vent to outside air.
</para>
</chapter>
<chapter>
- <title>Hardware Overview</title>
- <para>
- TeleMetrum is a 1 inch by 2.75 inch circuit board. It was designed to
- fit inside coupler for 29mm air-frame tubing, but using it in a tube that
- small in diameter may require some creativity in mounting and wiring
- to succeed! The presence of an accelerometer means TeleMetrum should
- be aligned along the flight axis of the airframe, and by default the 1/4
- wave UHF wire antenna should be on the nose-cone end of the board. The
- antenna wire is about 7 inches long, and wiring for a power switch and
- the e-matches for apogee and main ejection charges depart from the
- fin can end of the board, meaning an ideal "simple" avionics
- bay for TeleMetrum should have at least 10 inches of interior length.
- </para>
- <para>
- TeleMini is a 0.5 inch by 1.5 inch circuit board. It was designed to
- fit inside an 18mm air-frame tube, but using it in a tube that
- small in diameter may require some creativity in mounting and wiring
- to succeed! Since there is no accelerometer, TeleMini can be mounted
- in any convenient orientation. The default 1/4
- wave UHF wire antenna attached to the center of one end of
- the board is about 7 inches long, and wiring for a power switch and
- the e-matches for apogee and main ejection charges depart from the
- other end of the board, meaning an ideal "simple" avionics
- bay for TeleMini should have at least 9 inches of interior length.
- </para>
- <para>
- A typical TeleMetrum or TeleMini installation involves attaching
- only a suitable Lithium Polymer battery, a single pole switch for
- power on/off, and two pairs of wires connecting e-matches for the
- apogee and main ejection charges.
- </para>
- <para>
- By default, we use the unregulated output of the Li-Po battery directly
- to fire ejection charges. This works marvelously with standard
- low-current e-matches like the J-Tek from MJG Technologies, and with
- Quest Q2G2 igniters. However, if you want or need to use a separate
- pyro battery, check out the "External Pyro Battery" section in this
- manual for instructions on how to wire that up. The altimeters are
- designed to work with an external pyro battery of no more than 15 volts.
- </para>
- <para>
- Ejection charges are wired directly to the screw terminal block
- at the aft end of the altimeter. You'll need a very small straight
- blade screwdriver for these screws, such as you might find in a
- jeweler's screwdriver set.
- </para>
- <para>
- TeleMetrum also uses the screw terminal block for the power
- switch leads. On TeleMini, the power switch leads are soldered
- directly to the board and can be connected directly to a switch.
- </para>
- <para>
- For most air-frames, the integrated antennas are more than
- adequate. However, if you are installing in a carbon-fiber or
- metal electronics bay which is opaque to RF signals, you may need to
- use off-board external antennas instead. In this case, you can
- order an altimeter with an SMA connector for the UHF antenna
- connection, and, on TeleMetrum, you can unplug the integrated GPS
- antenna and select an appropriate off-board GPS antenna with
- cable terminating in a U.FL connector.
- </para>
+ <title>Altus Metrum Hardware</title>
+ <section>
+ <title>General Usage Instructions</title>
+ <para>
+ Here are general instructions for hooking up an Altus Metrum
+ flight computer. Instructions specific to each model will be
+ found in the section devoted to that model below.
+ </para>
+ <para>
+ To prevent electrical interference from affecting the
+ operation of the flight computer, it's important to always
+ twist pairs of wires connected to the board. Twist the switch
+ leads, the pyro leads and the battery leads. This reduces
+ interference through a mechanism called common mode rejection.
+ </para>
+ <section>
+ <title>Hooking Up Lithium Polymer Batteries</title>
+ <para>
+ All Altus Metrum flight computers have a two pin JST PH
+ series connector to connect up a single-cell Lithium Polymer
+ cell (3.7V nominal). You can purchase matching batteries
+ from the Altus Metrum store, or other vendors, or you can
+ make your own. Pin 1 of the connector is positive, pin 2 is
+ negative. Spark Fun sells a cable with the connector
+ attached, which they call a <ulink
+ url="https://www.sparkfun.com/products/9914">JST Jumper 2
+ Wire Assembly</ulink>.
+ </para>
+ <para>
+ Many RC vendors also sell lithium polymer batteries with
+ this same connector. All that we have found use the opposite
+ polarity, and if you use them that way, you will damage or
+ destroy the flight computer.
+ </para>
+ </section>
+ <section>
+ <title>Hooking Up Pyro Charges</title>
+ <para>
+ Altus Metrum flight computers always have two screws for
+ each pyro charge. This means you shouldn't need to put two
+ wires into a screw terminal or connect leads from pyro
+ charges together externally.
+ </para>
+ <para>
+ On the flight computer, one lead from each charge is hooked
+ to the positive battery terminal through the power switch.
+ The other lead is connected through the pyro circuit, which
+ is connected to the negative battery terminal when the pyro
+ circuit is fired.
+ </para>
+ </section>
+ <section>
+ <title>Hooking Up a Power Switch</title>
+ <para>
+ Altus Metrum flight computers need an external power switch
+ to turn them on. This disconnects both the computer and the
+ pyro charges from the battery, preventing the charges from
+ firing when in the Off position. The switch is in-line with
+ the positive battery terminal.
+ </para>
+ <section>
+ <title>Using an External Active Switch Circuit</title>
+ <para>
+ You can use an active switch circuit, such as the
+ Featherweight Magnetic Switch, with any Altus Metrum
+ flight computer. These require three connections, one to
+ the battery, one to the positive power input on the flight
+ computer and one to ground. Find instructions on how to
+ hook these up for each flight computer below. The follow
+ the instructions that come with your active switch to
+ connect it up.
+ </para>
+ </section>
+ </section>
+ <section>
+ <title>Using a Separate Pyro Battery</title>
+ <para>
+ As mentioned above in the section on hooking up pyro
+ charges, one lead for each of the pyro charges is connected
+ through the power switch directly to the positive battery
+ terminal. The other lead is connected to the pyro circuit,
+ which connects it to the negative battery terminal when the
+ pyro circuit is fired. The pyro circuit on all of the flight
+ computers is designed to handle up to 16V.
+ </para>
+ <para>
+ To use a separate pyro battery, connect the negative pyro
+ battery terminal to the flight computer ground terminal,
+ the positive battery terminal to the igniter and the other
+ igniter lead to the negative pyro terminal on the flight
+ computer. When the pyro channel fires, it will complete the
+ circuit between the negative pyro terminal and the ground
+ terminal, firing the igniter. Specific instructions on how
+ to hook this up will be found in each section below.
+ </para>
+ </section>
+ <section>
+ <title>Using a Different Kind of Battery</title>
+ <para>
+ EasyMini and TeleMini v2 are designed to use either a
+ lithium polymer battery or any other battery producing
+ between 4 and 12 volts, such as a rectangular 9V
+ battery. TeleMega and TeleMetrum are not designed for this,
+ and must only be powered by a lithium polymer battery. Find
+ instructions on how to use other batteries in the EasyMini
+ and TeleMini sections below.
+ </para>
+ </section>
+ </section>
+ <section>
+ <title>Specifications</title>
+ <para>
+ Here's the full set of Altus Metrum products, both in
+ production and retired.
+ </para>
+ <table frame='all'>
+ <title>Altus Metrum Electronics</title>
+ <?dbfo keep-together="always"?>
+ <tgroup cols='8' align='center' colsep='1' rowsep='1'>
+ <colspec align='center' colwidth='*' colname='Device'/>
+ <colspec align='center' colwidth='*' colname='Barometer'/>
+ <colspec align='center' colwidth='*' colname='Z-axis accelerometer'/>
+ <colspec align='center' colwidth='*' colname='GPS'/>
+ <colspec align='center' colwidth='*' colname='3D sensors'/>
+ <colspec align='center' colwidth='*' colname='Storage'/>
+ <colspec align='center' colwidth='*' colname='RF'/>
+ <colspec align='center' colwidth='*' colname='Battery'/>
+ <thead>
+ <row>
+ <entry align='center'>Device</entry>
+ <entry align='center'>Barometer</entry>
+ <entry align='center'>Z-axis accelerometer</entry>
+ <entry align='center'>GPS</entry>
+ <entry align='center'>3D sensors</entry>
+ <entry align='center'>Storage</entry>
+ <entry align='center'>RF Output</entry>
+ <entry align='center'>Battery</entry>
+ </row>
+ </thead>
+ <tbody>
+ <row>
+ <entry>TeleMetrum v1.0</entry>
+ <entry><para>MP3H6115 10km (33k')</para></entry>
+ <entry><para>MMA2202 50g</para></entry>
+ <entry>SkyTraq</entry>
+ <entry>-</entry>
+ <entry>1MB</entry>
+ <entry>10mW</entry>
+ <entry>3.7V</entry>
+ </row>
+ <row>
+ <entry>TeleMetrum v1.1</entry>
+ <entry><para>MP3H6115 10km (33k')</para></entry>
+ <entry><para>MMA2202 50g</para></entry>
+ <entry>SkyTraq</entry>
+ <entry>-</entry>
+ <entry>2MB</entry>
+ <entry>10mW</entry>
+ <entry>3.7V</entry>
+ </row>
+ <row>
+ <entry>TeleMetrum v1.2</entry>
+ <entry><para>MP3H6115 10km (33k')</para></entry>
+ <entry><para>ADXL78 70g</para></entry>
+ <entry>SkyTraq</entry>
+ <entry>-</entry>
+ <entry>2MB</entry>
+ <entry>10mW</entry>
+ <entry>3.7V</entry>
+ </row>
+ <row>
+ <entry>TeleMetrum v2.0</entry>
+ <entry><para>MS5607 30km (100k')</para></entry>
+ <entry><para>MMA6555 102g</para></entry>
+ <entry>uBlox Max-7Q</entry>
+ <entry>-</entry>
+ <entry>8MB</entry>
+ <entry>40mW</entry>
+ <entry>3.7V</entry>
+ </row>
+ <row>
+ <entry><para>TeleMini <?linebreak?>v1.0</para></entry>
+ <entry><para>MP3H6115 10km (33k')</para></entry>
+ <entry>-</entry>
+ <entry>-</entry>
+ <entry>-</entry>
+ <entry>5kB</entry>
+ <entry>10mW</entry>
+ <entry>3.7V</entry>
+ </row>
+ <row>
+ <entry>TeleMini <?linebreak?>v2.0</entry>
+ <entry><para>MS5607 30km (100k')</para></entry>
+ <entry>-</entry>
+ <entry>-</entry>
+ <entry>-</entry>
+ <entry>1MB</entry>
+ <entry>10mW</entry>
+ <entry>3.7-12V</entry>
+ </row>
+ <row>
+ <entry>EasyMini <?linebreak?>v1.0</entry>
+ <entry><para>MS5607 30km (100k')</para></entry>
+ <entry>-</entry>
+ <entry>-</entry>
+ <entry>-</entry>
+ <entry>1MB</entry>
+ <entry>-</entry>
+ <entry>3.7-12V</entry>
+ </row>
+ <row>
+ <entry>TeleMega <?linebreak?>v1.0</entry>
+ <entry><para>MS5607 30km (100k')</para></entry>
+ <entry><para>MMA6555 102g</para></entry>
+ <entry>uBlox Max-7Q</entry>
+ <entry><para>MPU6000 HMC5883</para></entry>
+ <entry>8MB</entry>
+ <entry>40mW</entry>
+ <entry>3.7V</entry>
+ </row>
+ </tbody>
+ </tgroup>
+ </table>
+ <table frame='all'>
+ <title>Altus Metrum Boards</title>
+ <?dbfo keep-together="always"?>
+ <tgroup cols='6' align='center' colsep='1' rowsep='1'>
+ <colspec align='center' colwidth='*' colname='Device'/>
+ <colspec align='center' colwidth='*' colname='Connectors'/>
+ <colspec align='center' colwidth='*' colname='Screw Terminals'/>
+ <colspec align='center' colwidth='*' colname='Width'/>
+ <colspec align='center' colwidth='*' colname='Length'/>
+ <colspec align='center' colwidth='*' colname='Tube Size'/>
+ <thead>
+ <row>
+ <entry align='center'>Device</entry>
+ <entry align='center'>Connectors</entry>
+ <entry align='center'>Screw Terminals</entry>
+ <entry align='center'>Width</entry>
+ <entry align='center'>Length</entry>
+ <entry align='center'>Tube Size</entry>
+ </row>
+ </thead>
+ <tbody>
+ <row>
+ <entry>TeleMetrum</entry>
+ <entry><para>
+ Antenna<?linebreak?>
+ Debug<?linebreak?>
+ Companion<?linebreak?>
+ USB<?linebreak?>
+ Battery
+ </para></entry>
+ <entry><para>Apogee pyro <?linebreak?>Main pyro <?linebreak?>Switch</para></entry>
+ <entry>1 inch (2.54cm)</entry>
+ <entry>2 ¾ inch (6.99cm)</entry>
+ <entry>29mm coupler</entry>
+ </row>
+ <row>
+ <entry><para>TeleMini <?linebreak?>v1.0</para></entry>
+ <entry><para>
+ Antenna<?linebreak?>
+ Debug<?linebreak?>
+ Battery
+ </para></entry>
+ <entry><para>
+ Apogee pyro <?linebreak?>
+ Main pyro
+ </para></entry>
+ <entry>½ inch (1.27cm)</entry>
+ <entry>1½ inch (3.81cm)</entry>
+ <entry>18mm coupler</entry>
+ </row>
+ <row>
+ <entry>TeleMini <?linebreak?>v2.0</entry>
+ <entry><para>
+ Antenna<?linebreak?>
+ Debug<?linebreak?>
+ USB<?linebreak?>
+ Battery
+ </para></entry>
+ <entry><para>
+ Apogee pyro <?linebreak?>
+ Main pyro <?linebreak?>
+ Battery <?linebreak?>
+ Switch
+ </para></entry>
+ <entry>0.8 inch (2.03cm)</entry>
+ <entry>1½ inch (3.81cm)</entry>
+ <entry>24mm coupler</entry>
+ </row>
+ <row>
+ <entry>EasyMini</entry>
+ <entry><para>
+ Debug<?linebreak?>
+ USB<?linebreak?>
+ Battery
+ </para></entry>
+ <entry><para>
+ Apogee pyro <?linebreak?>
+ Main pyro <?linebreak?>
+ Battery <?linebreak?>
+ Switch
+ </para></entry>
+ <entry>0.8 inch (2.03cm)</entry>
+ <entry>1½ inch (3.81cm)</entry>
+ <entry>24mm coupler</entry>
+ </row>
+ <row>
+ <entry>TeleMega</entry>
+ <entry><para>
+ Antenna<?linebreak?>
+ Debug<?linebreak?>
+ Companion<?linebreak?>
+ USB<?linebreak?>
+ Battery
+ </para></entry>
+ <entry><para>
+ Apogee pyro <?linebreak?>
+ Main pyro<?linebreak?>
+ Pyro A-D<?linebreak?>
+ Switch<?linebreak?>
+ Pyro battery
+ </para></entry>
+ <entry>1¼ inch (3.18cm)</entry>
+ <entry>3¼ inch (8.26cm)</entry>
+ <entry>38mm coupler</entry>
+ </row>
+ </tbody>
+ </tgroup>
+ </table>
+ </section>
+ <section>
+ <title>TeleMetrum</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="telemetrum-v1.1-thside.jpg" width="5.5in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ TeleMetrum is a 1 inch by 2¾ inch circuit board. It was designed to
+ fit inside coupler for 29mm air-frame tubing, but using it in a tube that
+ small in diameter may require some creativity in mounting and wiring
+ to succeed! The presence of an accelerometer means TeleMetrum should
+ be aligned along the flight axis of the airframe, and by default the ¼
+ wave UHF wire antenna should be on the nose-cone end of the board. The
+ antenna wire is about 7 inches long, and wiring for a power switch and
+ the e-matches for apogee and main ejection charges depart from the
+ fin can end of the board, meaning an ideal “simple” avionics
+ bay for TeleMetrum should have at least 10 inches of interior length.
+ </para>
+ <section>
+ <title>TeleMetrum Screw Terminals</title>
+ <para>
+ TeleMetrum has six screw terminals on the end of the board
+ opposite the telemetry antenna. Two are for the power
+ switch, and two each for the apogee and main igniter
+ circuits. Using the picture above and starting from the top,
+ the terminals are as follows:
+ </para>
+ <table frame='all'>
+ <title>TeleMetrum Screw Terminals</title>
+ <?dbfo keep-together="always"?>
+ <tgroup cols='3' align='center' colsep='1' rowsep='1'>
+ <colspec align='center' colwidth='*' colname='Pin #'/>
+ <colspec align='center' colwidth='2*' colname='Pin Name'/>
+ <colspec align='left' colwidth='5*' colname='Description'/>
+ <thead>
+ <row>
+ <entry align='center'>Terminal #</entry>
+ <entry align='center'>Terminal Name</entry>
+ <entry align='center'>Description</entry>
+ </row>
+ </thead>
+ <tbody>
+ <row>
+ <entry>1</entry>
+ <entry>Switch Output</entry>
+ <entry>Switch connection to flight computer</entry>
+ </row>
+ <row>
+ <entry>2</entry>
+ <entry>Switch Input</entry>
+ <entry>Switch connection to positive battery terminal</entry>
+ </row>
+ <row>
+ <entry>3</entry>
+ <entry>Main +</entry>
+ <entry>Main pyro channel common connection to battery +</entry>
+ </row>
+ <row>
+ <entry>4</entry>
+ <entry>Main -</entry>
+ <entry>Main pyro channel connection to pyro circuit</entry>
+ </row>
+ <row>
+ <entry>5</entry>
+ <entry>Apogee +</entry>
+ <entry>Apogee pyro channel common connection to battery +</entry>
+ </row>
+ <row>
+ <entry>6</entry>
+ <entry>Apogee -</entry>
+ <entry>Apogee pyro channel connection to pyro circuit</entry>
+ </row>
+ </tbody>
+ </tgroup>
+ </table>
+ </section>
+ <section>
+ <title>Using a Separate Pyro Battery with TeleMetrum</title>
+ <para>
+ As described above, using an external pyro battery involves
+ connecting the negative battery terminal to the flight
+ computer ground, connecting the positive battery terminal to
+ one of the igniter leads and connecting the other igniter
+ lead to the per-channel pyro circuit connection.
+ </para>
+ <para>
+ To connect the negative battery terminal to the TeleMetrum
+ ground, insert a small piece of wire, 24 to 28 gauge
+ stranded, into the GND hole just above the screw terminal
+ strip and solder it in place.
+ </para>
+ <para>
+ Connecting the positive battery terminal to the pyro
+ charges must be done separate from TeleMetrum, by soldering
+ them together or using some other connector.
+ </para>
+ <para>
+ The other lead from each pyro charge is then inserted into
+ the appropriate per-pyro channel screw terminal (terminal 4 for the
+ Main charge, terminal 6 for the Apogee charge).
+ </para>
+ </section>
+ <section>
+ <title>Using an Active Switch with TeleMetrum</title>
+ <para>
+ As explained above, an external active switch requires three
+ connections, one to the positive battery terminal, one to
+ the flight computer positive input and one to ground.
+ </para>
+ <para>
+ The positive battery terminal is available on screw terminal
+ 2, the positive flight computer input is on terminal 1. To
+ hook a lead to ground, solder a piece of wire, 24 to 28
+ gauge stranded, to the GND hole just above terminal 1.
+ </para>
+ </section>
+ </section>
+ <section>
+ <title>TeleMini v1.0</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="telemini-v1-top.jpg" width="5.5in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ TeleMini v1.0 is ½ inches by 1½ inches. It was
+ designed to fit inside an 18mm air-frame tube, but using it in
+ a tube that small in diameter may require some creativity in
+ mounting and wiring to succeed! Since there is no
+ accelerometer, TeleMini can be mounted in any convenient
+ orientation. The default ¼ wave UHF wire antenna attached to
+ the center of one end of the board is about 7 inches long. Two
+ wires for the power switch are connected to holes in the
+ middle of the board. Screw terminals for the e-matches for
+ apogee and main ejection charges depart from the other end of
+ the board, meaning an ideal “simple” avionics bay for TeleMini
+ should have at least 9 inches of interior length.
+ </para>
+ <section>
+ <title>TeleMini v1.0 Screw Terminals</title>
+ <para>
+ TeleMini v1.0 has four screw terminals on the end of the
+ board opposite the telemetry antenna. Two are for the apogee
+ and two are for main igniter circuits. There are also wires
+ soldered to the board for the power switch. Using the
+ picture above and starting from the top for the terminals
+ and from the left for the power switch wires, the
+ connections are as follows:
+ </para>
+ <table frame='all'>
+ <title>TeleMini v1.0 Connections</title>
+ <?dbfo keep-together="always"?>
+ <tgroup cols='3' align='center' colsep='1' rowsep='1'>
+ <colspec align='center' colwidth='*' colname='Pin #'/>
+ <colspec align='center' colwidth='2*' colname='Pin Name'/>
+ <colspec align='left' colwidth='5*' colname='Description'/>
+ <thead>
+ <row>
+ <entry align='center'>Terminal #</entry>
+ <entry align='center'>Terminal Name</entry>
+ <entry align='center'>Description</entry>
+ </row>
+ </thead>
+ <tbody>
+ <row>
+ <entry>1</entry>
+ <entry>Apogee -</entry>
+ <entry>Apogee pyro channel connection to pyro circuit</entry>
+ </row>
+ <row>
+ <entry>2</entry>
+ <entry>Apogee +</entry>
+ <entry>Apogee pyro channel common connection to battery +</entry>
+ </row>
+ <row>
+ <entry>3</entry>
+ <entry>Main -</entry>
+ <entry>Main pyro channel connection to pyro circuit</entry>
+ </row>
+ <row>
+ <entry>4</entry>
+ <entry>Main +</entry>
+ <entry>Main pyro channel common connection to battery +</entry>
+ </row>
+ <row>
+ <entry>Left</entry>
+ <entry>Switch Output</entry>
+ <entry>Switch connection to flight computer</entry>
+ </row>
+ <row>
+ <entry>Right</entry>
+ <entry>Switch Input</entry>
+ <entry>Switch connection to positive battery terminal</entry>
+ </row>
+ </tbody>
+ </tgroup>
+ </table>
+ </section>
+ <section>
+ <title>Using a Separate Pyro Battery with TeleMini v1.0</title>
+ <para>
+ As described above, using an external pyro battery involves
+ connecting the negative battery terminal to the flight
+ computer ground, connecting the positive battery terminal to
+ one of the igniter leads and connecting the other igniter
+ lead to the per-channel pyro circuit connection. Because
+ there is no solid ground connection to use on TeleMini, this
+ is not recommended.
+ </para>
+ <para>
+ The only available ground connection on TeleMini v1.0 are
+ the two mounting holes next to the telemetry
+ antenna. Somehow connect a small piece of wire to one of
+ those holes and hook it to the negative pyro battery terminal.
+ </para>
+ <para>
+ Connecting the positive battery terminal to the pyro
+ charges must be done separate from TeleMini v1.0, by soldering
+ them together or using some other connector.
+ </para>
+ <para>
+ The other lead from each pyro charge is then inserted into
+ the appropriate per-pyro channel screw terminal (terminal 3 for the
+ Main charge, terminal 1 for the Apogee charge).
+ </para>
+ </section>
+ <section>
+ <title>Using an Active Switch with TeleMini v1.0</title>
+ <para>
+ As explained above, an external active switch requires three
+ connections, one to the positive battery terminal, one to
+ the flight computer positive input and one to ground. Again,
+ because TeleMini doesn't have any good ground connection,
+ this is not recommended.
+ </para>
+ <para>
+ The positive battery terminal is available on the Right
+ power switch wire, the positive flight computer input is on
+ the left power switch wire. Hook a lead to either of the
+ mounting holes for a ground connection.
+ </para>
+ </section>
+ </section>
+ <section>
+ <title>TeleMini v2.0</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="telemini-v2-top.jpg" width="5.5in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ TeleMini v2.0 is 0.8 inches by 1½ inches. It adds more
+ on-board data logging memory, a built-in USB connector and
+ screw terminals for the battery and power switch. The larger
+ board fits in a 24mm coupler. There's also a battery connector
+ for a LiPo battery if you want to use one of those.
+ </para>
+ <section>
+ <title>TeleMini v2.0 Screw Terminals</title>
+ <para>
+ TeleMini v2.0 has two sets of four screw terminals on the end of the
+ board opposite the telemetry antenna. Using the picture
+ above, the top four have connections for the main pyro
+ circuit and an external battery and the bottom four have
+ connections for the apogee pyro circuit and the power
+ switch. Counting from the left, the connections are as follows:
+ </para>
+ <table frame='all'>
+ <title>TeleMini v2.0 Connections</title>
+ <?dbfo keep-together="always"?>
+ <tgroup cols='3' align='center' colsep='1' rowsep='1'>
+ <colspec align='center' colwidth='*' colname='Pin #'/>
+ <colspec align='center' colwidth='2*' colname='Pin Name'/>
+ <colspec align='left' colwidth='5*' colname='Description'/>
+ <thead>
+ <row>
+ <entry align='center'>Terminal #</entry>
+ <entry align='center'>Terminal Name</entry>
+ <entry align='center'>Description</entry>
+ </row>
+ </thead>
+ <tbody>
+ <row>
+ <entry>Top 1</entry>
+ <entry>Main -</entry>
+ <entry>Main pyro channel connection to pyro circuit</entry>
+ </row>
+ <row>
+ <entry>Top 2</entry>
+ <entry>Main +</entry>
+ <entry>Main pyro channel common connection to battery +</entry>
+ </row>
+ <row>
+ <entry>Top 3</entry>
+ <entry>Battery +</entry>
+ <entry>Positive external battery terminal</entry>
+ </row>
+ <row>
+ <entry>Top 4</entry>
+ <entry>Battery -</entry>
+ <entry>Negative external battery terminal</entry>
+ </row>
+ <row>
+ <entry>Bottom 1</entry>
+ <entry>Apogee -</entry>
+ <entry>Apogee pyro channel connection to pyro circuit</entry>
+ </row>
+ <row>
+ <entry>Bottom 2</entry>
+ <entry>Apogee +</entry>
+ <entry>Apogee pyro channel common connection to
+ battery +</entry>
+ </row>
+ <row>
+ <entry>Bottom 3</entry>
+ <entry>Switch Output</entry>
+ <entry>Switch connection to flight computer</entry>
+ </row>
+ <row>
+ <entry>Bottom 4</entry>
+ <entry>Switch Input</entry>
+ <entry>Switch connection to positive battery terminal</entry>
+ </row>
+ </tbody>
+ </tgroup>
+ </table>
+ </section>
+ <section>
+ <title>Using a Separate Pyro Battery with TeleMini v2.0</title>
+ <para>
+ As described above, using an external pyro battery involves
+ connecting the negative battery terminal to the flight
+ computer ground, connecting the positive battery terminal to
+ one of the igniter leads and connecting the other igniter
+ lead to the per-channel pyro circuit connection.
+ </para>
+ <para>
+ To connect the negative pyro battery terminal to TeleMini
+ ground, connect it to the negative external battery
+ connection, top terminal 4.
+ </para>
+ <para>
+ Connecting the positive battery terminal to the pyro
+ charges must be done separate from TeleMini v2.0, by soldering
+ them together or using some other connector.
+ </para>
+ <para>
+ The other lead from each pyro charge is then inserted into
+ the appropriate per-pyro channel screw terminal (top
+ terminal 1 for the Main charge, bottom terminal 1 for the
+ Apogee charge).
+ </para>
+ </section>
+ <section>
+ <title>Using an Active Switch with TeleMini v2.0</title>
+ <para>
+ As explained above, an external active switch requires three
+ connections, one to the positive battery terminal, one to
+ the flight computer positive input and one to ground. Use
+ the negative external battery connection, top terminal 4 for
+ ground.
+ </para>
+ <para>
+ The positive battery terminal is available on bottom
+ terminal 4, the positive flight computer input is on the
+ bottom terminal 3.
+ </para>
+ </section>
+ </section>
+ <section>
+ <title>EasyMini</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="easymini-top.jpg" width="5.5in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ EasyMini is built on a 0.8 inch by 1½ inch circuit board. It's
+ designed to fit in a 24mm coupler tube. The connectors and
+ screw terminals match TeleMini v2.0, so you can easily swap between
+ EasyMini and TeleMini.
+ </para>
+ <section>
+ <title>EasyMini Screw Terminals</title>
+ <para>
+ EasyMini has two sets of four screw terminals on the end of the
+ board opposite the telemetry antenna. Using the picture
+ above, the top four have connections for the main pyro
+ circuit and an external battery and the bottom four have
+ connections for the apogee pyro circuit and the power
+ switch. Counting from the left, the connections are as follows:
+ </para>
+ <table frame='all'>
+ <title>EasyMini Connections</title>
+ <?dbfo keep-together="always"?>
+ <tgroup cols='3' align='center' colsep='1' rowsep='1'>
+ <colspec align='center' colwidth='*' colname='Pin #'/>
+ <colspec align='center' colwidth='2*' colname='Pin Name'/>
+ <colspec align='left' colwidth='5*' colname='Description'/>
+ <thead>
+ <row>
+ <entry align='center'>Terminal #</entry>
+ <entry align='center'>Terminal Name</entry>
+ <entry align='center'>Description</entry>
+ </row>
+ </thead>
+ <tbody>
+ <row>
+ <entry>Top 1</entry>
+ <entry>Main -</entry>
+ <entry>Main pyro channel connection to pyro circuit</entry>
+ </row>
+ <row>
+ <entry>Top 2</entry>
+ <entry>Main +</entry>
+ <entry>Main pyro channel common connection to battery +</entry>
+ </row>
+ <row>
+ <entry>Top 3</entry>
+ <entry>Battery +</entry>
+ <entry>Positive external battery terminal</entry>
+ </row>
+ <row>
+ <entry>Top 4</entry>
+ <entry>Battery -</entry>
+ <entry>Negative external battery terminal</entry>
+ </row>
+ <row>
+ <entry>Bottom 1</entry>
+ <entry>Apogee -</entry>
+ <entry>Apogee pyro channel connection to pyro circuit</entry>
+ </row>
+ <row>
+ <entry>Bottom 2</entry>
+ <entry>Apogee +</entry>
+ <entry>Apogee pyro channel common connection to
+ battery +</entry>
+ </row>
+ <row>
+ <entry>Bottom 3</entry>
+ <entry>Switch Output</entry>
+ <entry>Switch connection to flight computer</entry>
+ </row>
+ <row>
+ <entry>Bottom 4</entry>
+ <entry>Switch Input</entry>
+ <entry>Switch connection to positive battery terminal</entry>
+ </row>
+ </tbody>
+ </tgroup>
+ </table>
+ </section>
+ <section>
+ <title>Using a Separate Pyro Battery with EasyMini</title>
+ <para>
+ As described above, using an external pyro battery involves
+ connecting the negative battery terminal to the flight
+ computer ground, connecting the positive battery terminal to
+ one of the igniter leads and connecting the other igniter
+ lead to the per-channel pyro circuit connection.
+ </para>
+ <para>
+ To connect the negative pyro battery terminal to TeleMini
+ ground, connect it to the negative external battery
+ connection, top terminal 4.
+ </para>
+ <para>
+ Connecting the positive battery terminal to the pyro
+ charges must be done separate from EasyMini, by soldering
+ them together or using some other connector.
+ </para>
+ <para>
+ The other lead from each pyro charge is then inserted into
+ the appropriate per-pyro channel screw terminal (top
+ terminal 1 for the Main charge, bottom terminal 1 for the
+ Apogee charge).
+ </para>
+ </section>
+ <section>
+ <title>Using an Active Switch with EasyMini</title>
+ <para>
+ As explained above, an external active switch requires three
+ connections, one to the positive battery terminal, one to
+ the flight computer positive input and one to ground. Use
+ the negative external battery connection, top terminal 4 for
+ ground.
+ </para>
+ <para>
+ The positive battery terminal is available on bottom
+ terminal 4, the positive flight computer input is on the
+ bottom terminal 3.
+ </para>
+ </section>
+ </section>
+ <section>
+ <title>TeleMega</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="telemega-v1.0-top.jpg" width="5.5in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ TeleMega is a 1¼ inch by 3¼ inch circuit board. It was
+ designed to easily fit in a 38mm coupler. Like TeleMetrum,
+ TeleMega has an accelerometer and so it must be mounted so that
+ the board is aligned with the flight axis. It can be mounted
+ either antenna up or down.
+ </para>
+ <section>
+ <title>TeleMega Screw Terminals</title>
+ <para>
+ TeleMega has two sets of nine screw terminals on the end of
+ the board opposite the telemetry antenna. They are as follows:
+ </para>
+ <table frame='all'>
+ <title>TeleMega Screw Terminals</title>
+ <?dbfo keep-together="always"?>
+ <tgroup cols='3' align='center' colsep='1' rowsep='1'>
+ <colspec align='center' colwidth='*' colname='Pin #'/>
+ <colspec align='center' colwidth='2*' colname='Pin Name'/>
+ <colspec align='left' colwidth='5*' colname='Description'/>
+ <thead>
+ <row>
+ <entry align='center'>Terminal #</entry>
+ <entry align='center'>Terminal Name</entry>
+ <entry align='center'>Description</entry>
+ </row>
+ </thead>
+ <tbody>
+ <row>
+ <entry>Top 1</entry>
+ <entry>Switch Input</entry>
+ <entry>Switch connection to positive battery terminal</entry>
+ </row>
+ <row>
+ <entry>Top 2</entry>
+ <entry>Switch Output</entry>
+ <entry>Switch connection to flight computer</entry>
+ </row>
+ <row>
+ <entry>Top 3</entry>
+ <entry>GND</entry>
+ <entry>Ground connection for use with external active switch</entry>
+ </row>
+ <row>
+ <entry>Top 4</entry>
+ <entry>Main -</entry>
+ <entry>Main pyro channel connection to pyro circuit</entry>
+ </row>
+ <row>
+ <entry>Top 5</entry>
+ <entry>Main +</entry>
+ <entry>Main pyro channel common connection to battery +</entry>
+ </row>
+ <row>
+ <entry>Top 6</entry>
+ <entry>Apogee -</entry>
+ <entry>Apogee pyro channel connection to pyro circuit</entry>
+ </row>
+ <row>
+ <entry>Top 7</entry>
+ <entry>Apogee +</entry>
+ <entry>Apogee pyro channel common connection to battery +</entry>
+ </row>
+ <row>
+ <entry>Top 8</entry>
+ <entry>D -</entry>
+ <entry>D pyro channel connection to pyro circuit</entry>
+ </row>
+ <row>
+ <entry>Top 9</entry>
+ <entry>D +</entry>
+ <entry>D pyro channel common connection to battery +</entry>
+ </row>
+ <row>
+ <entry>Bottom 1</entry>
+ <entry>GND</entry>
+ <entry>Ground connection for negative pyro battery terminal</entry>
+ </row>
+ <row>
+ <entry>Bottom 2</entry>
+ <entry>Pyro</entry>
+ <entry>Positive pyro battery terminal</entry>
+ </row>
+ <row>
+ <entry>Bottom 3</entry>
+ <entry>Lipo</entry>
+ <entry>
+ Power switch output. Use to connect main battery to
+ pyro battery input
+ </entry>
+ </row>
+ <row>
+ <entry>Bottom 4</entry>
+ <entry>A -</entry>
+ <entry>A pyro channel connection to pyro circuit</entry>
+ </row>
+ <row>
+ <entry>Bottom 5</entry>
+ <entry>A +</entry>
+ <entry>A pyro channel common connection to battery +</entry>
+ </row>
+ <row>
+ <entry>Bottom 6</entry>
+ <entry>B -</entry>
+ <entry>B pyro channel connection to pyro circuit</entry>
+ </row>
+ <row>
+ <entry>Bottom 7</entry>
+ <entry>B +</entry>
+ <entry>B pyro channel common connection to battery +</entry>
+ </row>
+ <row>
+ <entry>Bottom 8</entry>
+ <entry>C -</entry>
+ <entry>C pyro channel connection to pyro circuit</entry>
+ </row>
+ <row>
+ <entry>Bottom 9</entry>
+ <entry>C +</entry>
+ <entry>C pyro channel common connection to battery +</entry>
+ </row>
+ </tbody>
+ </tgroup>
+ </table>
+ </section>
+ <section>
+ <title>Using a Separate Pyro Battery with TeleMega</title>
+ <para>
+ TeleMega provides explicit support for an external pyro
+ battery. All that is required is to remove the jumper
+ between the lipo terminal (Bottom 3) and the pyro terminal
+ (Bottom 2). Then hook the negative pyro battery terminal to ground
+ (Bottom 1) and the positive pyro battery to the pyro battery
+ input (Bottom 2). You can then use the existing pyro screw
+ terminals to hook up all of the pyro charges.
+ </para>
+ </section>
+ <section>
+ <title>Using Only One Battery With TeleMega</title>
+ <para>
+ Because TeleMega has built-in support for a separate pyro
+ battery, if you want to fly with just one battery running
+ both the computer and firing the charges, you need to
+ connect the flight computer battery to the pyro
+ circuit. TeleMega has two screw terminals for this—hook a
+ wire from the Lipo terminal (Bottom 3) to the Pyro terminal
+ (Bottom 2).
+ </para>
+ </section>
+ <section>
+ <title>Using an Active Switch with TeleMega</title>
+ <para>
+ As explained above, an external active switch requires three
+ connections, one to the positive battery terminal, one to
+ the flight computer positive input and one to ground.
+ </para>
+ <para>
+ The positive battery terminal is available on Top terminal
+ 1, the positive flight computer input is on Top terminal
+ 2. Ground is on Top terminal 3.
+ </para>
+ </section>
+ </section>
+ <section>
+ <title>Flight Data Recording</title>
+ <para>
+ Each flight computer logs data at 100 samples per second
+ during ascent and 10 samples per second during descent, except
+ for TeleMini v1.0, which records ascent at 10 samples per
+ second and descent at 1 sample per second. Data are logged to
+ an on-board flash memory part, which can be partitioned into
+ several equal-sized blocks, one for each flight.
+ </para>
+ <table frame='all'>
+ <title>Data Storage on Altus Metrum altimeters</title>
+ <?dbfo keep-together="always"?>
+ <tgroup cols='4' align='center' colsep='1' rowsep='1'>
+ <colspec align='center' colwidth='*' colname='Device'/>
+ <colspec align='center' colwidth='*' colname='Bytes per sample'/>
+ <colspec align='center' colwidth='*' colname='Total storage'/>
+ <colspec align='center' colwidth='*' colname='Minutes of
+ full-rate'/>
+ <thead>
+ <row>
+ <entry align='center'>Device</entry>
+ <entry align='center'>Bytes per Sample</entry>
+ <entry align='center'>Total Storage</entry>
+ <entry align='center'>Minutes at Full Rate</entry>
+ </row>
+ </thead>
+ <tbody>
+ <row>
+ <entry>TeleMetrum v1.0</entry>
+ <entry>8</entry>
+ <entry>1MB</entry>
+ <entry>20</entry>
+ </row>
+ <row>
+ <entry>TeleMetrum v1.1 v1.2</entry>
+ <entry>8</entry>
+ <entry>2MB</entry>
+ <entry>40</entry>
+ </row>
+ <row>
+ <entry>TeleMetrum v2.0</entry>
+ <entry>16</entry>
+ <entry>8MB</entry>
+ <entry>80</entry>
+ </row>
+ <row>
+ <entry>TeleMini v1.0</entry>
+ <entry>2</entry>
+ <entry>5kB</entry>
+ <entry>4</entry>
+ </row>
+ <row>
+ <entry>TeleMini v2.0</entry>
+ <entry>16</entry>
+ <entry>1MB</entry>
+ <entry>10</entry>
+ </row>
+ <row>
+ <entry>EasyMini</entry>
+ <entry>16</entry>
+ <entry>1MB</entry>
+ <entry>10</entry>
+ </row>
+ <row>
+ <entry>TeleMega</entry>
+ <entry>32</entry>
+ <entry>8MB</entry>
+ <entry>40</entry>
+ </row>
+ </tbody>
+ </tgroup>
+ </table>
+ <para>
+ The on-board flash is partitioned into separate flight logs,
+ each of a fixed maximum size. Increase the maximum size of
+ each log and you reduce the number of flights that can be
+ stored. Decrease the size and you can store more flights.
+ </para>
+ <para>
+ Configuration data is also stored in the flash memory on
+ TeleMetrum v1.x, TeleMini and EasyMini. This consumes 64kB
+ of flash space. This configuration space is not available
+ for storing flight log data. TeleMetrum v2.0 and TeleMega
+ store configuration data in a bit of eeprom available within
+ the processor chip, leaving that space available in flash for
+ more flight data.
+ </para>
+ <para>
+ To compute the amount of space needed for a single flight, you
+ can multiply the expected ascent time (in seconds) by 100
+ times bytes-per-sample, multiply the expected descent time (in
+ seconds) by 10 times the bytes per sample and add the two
+ together. That will slightly under-estimate the storage (in
+ bytes) needed for the flight. For instance, a TeleMetrum v2.0 flight spending
+ 20 seconds in ascent and 150 seconds in descent will take
+ about (20 * 1600) + (150 * 160) = 56000 bytes of storage. You
+ could store dozens of these flights in the on-board flash.
+ </para>
+ <para>
+ The default size allows for several flights on each flight
+ computer, except for TeleMini v1.0, which only holds data for a
+ single flight. You can adjust the size.
+ </para>
+ <para>
+ Altus Metrum flight computers will not overwrite existing
+ flight data, so be sure to download flight data and erase it
+ from the flight computer before it fills up. The flight
+ computer will still successfully control the flight even if it
+ cannot log data, so the only thing you will lose is the data.
+ </para>
+ </section>
+ <section>
+ <title>Installation</title>
+ <para>
+ A typical installation involves attaching
+ only a suitable battery, a single pole switch for
+ power on/off, and two pairs of wires connecting e-matches for the
+ apogee and main ejection charges. All Altus Metrum products are
+ designed for use with single-cell batteries with 3.7 volts
+ nominal. TeleMini v2.0 and EasyMini may also be used with other
+ batteries as long as they supply between 4 and 12 volts.
+ </para>
+ <para>
+ The battery connectors are a standard 2-pin JST connector and
+ match batteries sold by Spark Fun. These batteries are
+ single-cell Lithium Polymer batteries that nominally provide 3.7
+ volts. Other vendors sell similar batteries for RC aircraft
+ using mating connectors, however the polarity for those is
+ generally reversed from the batteries used by Altus Metrum
+ products. In particular, the Tenergy batteries supplied for use
+ in Featherweight flight computers are not compatible with Altus
+ Metrum flight computers or battery chargers. <emphasis>Check
+ polarity and voltage before connecting any battery not purchased
+ from Altus Metrum or Spark Fun.</emphasis>
+ </para>
+ <para>
+ By default, we use the unregulated output of the battery directly
+ to fire ejection charges. This works marvelously with standard
+ low-current e-matches like the J-Tek from MJG Technologies, and with
+ Quest Q2G2 igniters. However, if you want or need to use a separate
+ pyro battery, check out the “External Pyro Battery” section in this
+ manual for instructions on how to wire that up. The altimeters are
+ designed to work with an external pyro battery of no more than 15 volts.
+ </para>
+ <para>
+ Ejection charges are wired directly to the screw terminal block
+ at the aft end of the altimeter. You'll need a very small straight
+ blade screwdriver for these screws, such as you might find in a
+ jeweler's screwdriver set.
+ </para>
+ <para>
+ Except for TeleMini v1.0, the flight computers also use the
+ screw terminal block for the power switch leads. On TeleMini v1.0,
+ the power switch leads are soldered directly to the board and
+ can be connected directly to a switch.
+ </para>
+ <para>
+ For most air-frames, the integrated antennas are more than
+ adequate. However, if you are installing in a carbon-fiber or
+ metal electronics bay which is opaque to RF signals, you may need to
+ use off-board external antennas instead. In this case, you can
+ replace the stock UHF antenna wire with an edge-launched SMA connector,
+ and, on TeleMetrum v1, you can unplug the integrated GPS
+ antenna and select an appropriate off-board GPS antenna with
+ cable terminating in a U.FL connector.
+ </para>
+ </section>
</chapter>
<chapter>
<title>System Operation</title>
<title>Firmware Modes </title>
<para>
The AltOS firmware build for the altimeters has two
- fundamental modes, "idle" and "flight". Which of these modes
+ fundamental modes, “idle” and “flight”. Which of these modes
the firmware operates in is determined at start up time. For
- TeleMetrum, the mode is controlled by the orientation of the
+ TeleMetrum and TeleMega, which have accelerometers, the mode is
+ controlled by the orientation of the
rocket (well, actually the board, of course...) at the time
- power is switched on. If the rocket is "nose up", then
- TeleMetrum assumes it's on a rail or rod being prepared for
+ power is switched on. If the rocket is “nose up”, then
+ the flight computer assumes it's on a rail or rod being prepared for
launch, so the firmware chooses flight mode. However, if the
rocket is more or less horizontal, the firmware instead enters
- idle mode. Since TeleMini doesn't have an accelerometer we can
- use to determine orientation, "idle" mode is selected when the
- board receives a command packet within the first five seconds
- of operation; if no packet is received, the board enters
- "flight" mode.
- </para>
- <para>
- At power on, you will hear three beeps or see three flashes
- ("S" in Morse code for start up) and then a pause while
- the altimeter completes initialization and self test, and decides
- which mode to enter next.
- </para>
- <para>
- In flight or "pad" mode, the altimeter engages the flight
- state machine, goes into transmit-only mode to
- send telemetry, and waits for launch to be detected.
- Flight mode is indicated by an "di-dah-dah-dit" ("P" for pad)
- on the beeper or lights, followed by beeps or flashes
- indicating the state of the pyrotechnic igniter continuity.
- One beep/flash indicates apogee continuity, two beeps/flashes
- indicate main continuity, three beeps/flashes indicate both
- apogee and main continuity, and one longer "brap" sound or
- rapidly alternating lights indicates no continuity. For a
+ idle mode. Since TeleMini v2.0 and EasyMini don't have an
+ accelerometer we can use to determine orientation, “idle” mode
+ is selected if the board is connected via USB to a computer,
+ otherwise the board enters “flight” mode. TeleMini v1.0
+ selects “idle” mode if it receives a command packet within the
+ first five seconds of operation.
+ </para>
+ <para>
+ At power on, the altimeter will beep out the battery voltage
+ to the nearest tenth of a volt. Each digit is represented by
+ a sequence of short “dit” beeps, with a pause between
+ digits. A zero digit is represented with one long “dah”
+ beep. Then there will be a short pause while the altimeter
+ completes initialization and self test, and decides which mode
+ to enter next.
+ </para>
+ <para>
+ Here's a short summary of all of the modes and the beeping (or
+ flashing, in the case of TeleMini v1) that accompanies each
+ mode. In the description of the beeping pattern, “dit” means a
+ short beep while "dah" means a long beep (three times as
+ long). “Brap” means a long dissonant tone.
+ <table frame='all'>
+ <title>AltOS Modes</title>
+ <?dbfo keep-together="always"?>
+ <tgroup cols='4' align='center' colsep='1' rowsep='1'>
+ <colspec align='center' colwidth='*' colname='Mode Name'/>
+ <colspec align='center' colwidth='*' colname='Letter'/>
+ <colspec align='center' colwidth='*' colname='Beeps'/>
+ <colspec align='center' colwidth='*' colname='Description'/>
+ <thead>
+ <row>
+ <entry>Mode Name</entry>
+ <entry>Abbreviation</entry>
+ <entry>Beeps</entry>
+ <entry>Description</entry>
+ </row>
+ </thead>
+ <tbody>
+ <row>
+ <entry>Startup</entry>
+ <entry>S</entry>
+ <entry>battery voltage in decivolts</entry>
+ <entry>
+ <para>
+ Calibrating sensors, detecting orientation.
+ </para>
+ </entry>
+ </row>
+ <row>
+ <entry>Idle</entry>
+ <entry>I</entry>
+ <entry>dit dit</entry>
+ <entry>
+ <para>
+ Ready to accept commands over USB or radio link.
+ </para>
+ </entry>
+ </row>
+ <row>
+ <entry>Pad</entry>
+ <entry>P</entry>
+ <entry>dit dah dah dit</entry>
+ <entry>
+ <para>
+ Waiting for launch. Not listening for commands.
+ </para>
+ </entry>
+ </row>
+ <row>
+ <entry>Boost</entry>
+ <entry>B</entry>
+ <entry>dah dit dit dit</entry>
+ <entry>
+ <para>
+ Accelerating upwards.
+ </para>
+ </entry>
+ </row>
+ <row>
+ <entry>Fast</entry>
+ <entry>F</entry>
+ <entry>dit dit dah dit</entry>
+ <entry>
+ <para>
+ Decelerating, but moving faster than 200m/s.
+ </para>
+ </entry>
+ </row>
+ <row>
+ <entry>Coast</entry>
+ <entry>C</entry>
+ <entry>dah dit dah dit</entry>
+ <entry>
+ <para>
+ Decelerating, moving slower than 200m/s
+ </para>
+ </entry>
+ </row>
+ <row>
+ <entry>Drogue</entry>
+ <entry>D</entry>
+ <entry>dah dit dit</entry>
+ <entry>
+ <para>
+ Descending after apogee. Above main height.
+ </para>
+ </entry>
+ </row>
+ <row>
+ <entry>Main</entry>
+ <entry>M</entry>
+ <entry>dah dah</entry>
+ <entry>
+ <para>
+ Descending. Below main height.
+ </para>
+ </entry>
+ </row>
+ <row>
+ <entry>Landed</entry>
+ <entry>L</entry>
+ <entry>dit dah dit dit</entry>
+ <entry>
+ <para>
+ Stable altitude for at least ten seconds.
+ </para>
+ </entry>
+ </row>
+ <row>
+ <entry>Sensor error</entry>
+ <entry>X</entry>
+ <entry>dah dit dit dah</entry>
+ <entry>
+ <para>
+ Error detected during sensor calibration.
+ </para>
+ </entry>
+ </row>
+ </tbody>
+ </tgroup>
+ </table>
+ </para>
+ <para>
+ In flight or “pad” mode, the altimeter engages the flight
+ state machine, goes into transmit-only mode to send telemetry,
+ and waits for launch to be detected. Flight mode is indicated
+ by an “di-dah-dah-dit” (“P” for pad) on the beeper or lights,
+ followed by beeps or flashes indicating the state of the
+ pyrotechnic igniter continuity. One beep/flash indicates
+ apogee continuity, two beeps/flashes indicate main continuity,
+ three beeps/flashes indicate both apogee and main continuity,
+ and one longer “brap” sound which is made by rapidly
+ alternating between two tones indicates no continuity. For a
dual deploy flight, make sure you're getting three beeps or
flashes before launching! For apogee-only or motor eject
flights, do what makes sense.
</para>
<para>
- If idle mode is entered, you will hear an audible "di-dit" or see
- two short flashes ("I" for idle), and the flight state machine is
- disengaged, thus no ejection charges will fire. The altimeters also
- listen for the radio link when in idle mode for requests sent via
- TeleDongle. Commands can be issued to a TeleMetrum in idle mode
- over either
- USB or the radio link equivalently. TeleMini only has the radio link.
- Idle mode is useful for configuring the altimeter, for extracting data
- from the on-board storage chip after flight, and for ground testing
- pyro charges.
+ If idle mode is entered, you will hear an audible “di-dit” or
+ see two short flashes (“I” for idle), and the flight state
+ machine is disengaged, thus no ejection charges will fire.
+ The altimeters also listen for the radio link when in idle
+ mode for requests sent via TeleDongle. Commands can be issued
+ in idle mode over either USB or the radio link
+ equivalently. TeleMini v1.0 only has the radio link. Idle
+ mode is useful for configuring the altimeter, for extracting
+ data from the on-board storage chip after flight, and for
+ ground testing pyro charges.
+ </para>
+ <para>
+ In “Idle” and “Pad” modes, once the mode indication
+ beeps/flashes and continuity indication has been sent, if
+ there is no space available to log the flight in on-board
+ memory, the flight computer will emit a warbling tone (much
+ slower than the “no continuity tone”)
</para>
<para>
- One "neat trick" of particular value when TeleMetrum is used with
+ Here's a summary of all of the “pad” and “idle” mode indications.
+ <table frame='all'>
+ <title>Pad/Idle Indications</title>
+ <?dbfo keep-together="always"?>
+ <tgroup cols='3' align='center' colsep='1' rowsep='1'>
+ <colspec align='center' colwidth='*' colname='Name'/>
+ <colspec align='center' colwidth='*' colname='Beeps'/>
+ <colspec align='center' colwidth='*' colname='Description'/>
+ <thead>
+ <row>
+ <entry>Name</entry>
+ <entry>Beeps</entry>
+ <entry>Description</entry>
+ </row>
+ </thead>
+ <tbody>
+ <row>
+ <entry>Neither</entry>
+ <entry>brap</entry>
+ <entry>
+ <para>
+ No continuity detected on either apogee or main
+ igniters.
+ </para>
+ </entry>
+ </row>
+ <row>
+ <entry>Apogee</entry>
+ <entry>dit</entry>
+ <entry>
+ <para>
+ Continuity detected only on apogee igniter.
+ </para>
+ </entry>
+ </row>
+ <row>
+ <entry>Main</entry>
+ <entry>dit dit</entry>
+ <entry>
+ <para>
+ Continuity detected only on main igniter.
+ </para>
+ </entry>
+ </row>
+ <row>
+ <entry>Both</entry>
+ <entry>dit dit dit</entry>
+ <entry>
+ <para>
+ Continuity detected on both igniters.
+ </para>
+ </entry>
+ </row>
+ <row>
+ <entry>Storage Full</entry>
+ <entry>warble</entry>
+ <entry>
+ <para>
+ On-board data logging storage is full. This will
+ not prevent the flight computer from safely
+ controlling the flight or transmitting telemetry
+ signals, but no record of the flight will be
+ stored in on-board flash.
+ </para>
+ </entry>
+ </row>
+ </tbody>
+ </tgroup>
+ </table>
+ </para>
+ <para>
+ Once landed, the flight computer will signal that by emitting
+ the “Landed” sound described above, after which it will beep
+ out the apogee height (in meters). Each digit is represented
+ by a sequence of short “dit” beeps, with a pause between
+ digits. A zero digit is represented with one long “dah”
+ beep. The flight computer will continue to report landed mode
+ and beep out the maximum height until turned off.
+ </para>
+ <para>
+ One “neat trick” of particular value when TeleMetrum or TeleMega are used with
very large air-frames, is that you can power the board up while the
rocket is horizontal, such that it comes up in idle mode. Then you can
raise the air-frame to launch position, and issue a 'reset' command
tower with a screw-driver trying to turn on your avionics before
installing igniters!
</para>
+ <para>
+ TeleMini v1.0 is configured solely via the radio link. Of course, that
+ means you need to know the TeleMini radio configuration values
+ or you won't be able to communicate with it. For situations
+ when you don't have the radio configuration values, TeleMini v1.0
+ offers an 'emergency recovery' mode. In this mode, TeleMini is
+ configured as follows:
+ <itemizedlist>
+ <listitem>
+ <para>
+ Sets the radio frequency to 434.550MHz
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Sets the radio calibration back to the factory value.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Sets the callsign to N0CALL
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Does not go to 'pad' mode after five seconds.
+ </para>
+ </listitem>
+ </itemizedlist>
+ </para>
+ <para>
+ To get into 'emergency recovery' mode, first find the row of
+ four small holes opposite the switch wiring. Using a short
+ piece of small gauge wire, connect the outer two holes
+ together, then power TeleMini up. Once the red LED is lit,
+ disconnect the wire and the board should signal that it's in
+ 'idle' mode after the initial five second startup period.
+ </para>
</section>
<section>
<title>GPS </title>
<para>
- TeleMetrum includes a complete GPS receiver. A complete explanation
- of how GPS works is beyond the scope of this manual, but the bottom
- line is that the TeleMetrum GPS receiver needs to lock onto at least
- four satellites to obtain a solid 3 dimensional position fix and know
- what time it is.
+ TeleMetrum and TeleMega include a complete GPS receiver. A
+ complete explanation of how GPS works is beyond the scope of
+ this manual, but the bottom line is that the GPS receiver
+ needs to lock onto at least four satellites to obtain a solid
+ 3 dimensional position fix and know what time it is.
</para>
<para>
- TeleMetrum provides backup power to the GPS chip any time a
- battery is connected. This allows the receiver to "warm start" on
+ The flight computers provide backup power to the GPS chip any time a
+ battery is connected. This allows the receiver to “warm start” on
the launch rail much faster than if every power-on were a GPS
- "cold start". In typical operations, powering up TeleMetrum
+ “cold start”. In typical operations, powering up
on the flight line in idle mode while performing final air-frame
preparation will be sufficient to allow the GPS receiver to cold
start and acquire lock. Then the board can be powered down during
<section>
<title>Controlling An Altimeter Over The Radio Link</title>
<para>
- One of the unique features of the Altus Metrum system is
- the ability to create a two way command link between TeleDongle
- and an altimeter using the digital radio transceivers built into
- each device. This allows you to interact with the altimeter from
- afar, as if it were directly connected to the computer.
+ One of the unique features of the Altus Metrum system is the
+ ability to create a two way command link between TeleDongle
+ and an altimeter using the digital radio transceivers
+ built into each device. This allows you to interact with the
+ altimeter from afar, as if it were directly connected to the
+ computer.
</para>
<para>
- Any operation which can be performed with TeleMetrum can
- either be done with TeleMetrum directly connected to the
+ Any operation which can be performed with a flight computer can
+ either be done with the device directly connected to the
computer via the USB cable, or through the radio
- link. TeleMini doesn't provide a USB connector and so it is
+ link. TeleMini v1.0 doesn't provide a USB connector and so it is
always communicated with over radio. Select the appropriate
TeleDongle device when the list of devices is presented and
AltosUI will interact with an altimeter over the radio link.
</listitem>
<listitem>
<para>
- Configure altimeter apogee delays or main deploy heights
+ Configure altimeter apogee delays, main deploy heights
+ and additional pyro event conditions
to respond to changing launch conditions. You can also
'reboot' the altimeter. Use this to remotely enable the
- flight computer by turning TeleMetrum on in "idle" mode,
+ flight computer by turning TeleMetrum or TeleMega on in “idle” mode,
then once the air-frame is oriented for launch, you can
reboot the altimeter and have it restart in pad mode
without having to climb the scary ladder.
<listitem>
<para>
Fire Igniters—Test your deployment charges without snaking
- wires out through holes in the air-frame. Simply assembly the
+ wires out through holes in the air-frame. Simply assemble the
rocket as if for flight with the apogee and main charges
loaded, then remotely command the altimeter to fire the
igniters.
close the window before performing other desired radio operations.
</para>
<para>
- TeleMetrum only enables radio commanding in 'idle' mode, so
- make sure you have TeleMetrum lying horizontally when you turn
- it on. Otherwise, TeleMetrum will start in 'pad' mode ready for
+ The flight computers only enable radio commanding in 'idle' mode.
+ TeleMetrum and TeleMega use the accelerometer to detect which orientation they
+ start up in, so make sure you have the flight computer lying horizontally when you turn
+ it on. Otherwise, it will start in 'pad' mode ready for
flight, and will not be listening for command packets from TeleDongle.
</para>
<para>
<para>
You can monitor the operation of the radio link by watching the
lights on the devices. The red LED will flash each time a packet
- is tramsitted, while the green LED will light up on TeleDongle when
+ is transmitted, while the green LED will light up on TeleDongle when
it is waiting to receive a packet from the altimeter.
</para>
</section>
An important aspect of preparing a rocket using electronic deployment
for flight is ground testing the recovery system. Thanks
to the bi-directional radio link central to the Altus Metrum system,
- this can be accomplished in a TeleMetrum or TeleMini equipped rocket
+ this can be accomplished in a TeleMega, TeleMetrum or TeleMini equipped rocket
with less work than you may be accustomed to with other systems. It
can even be fun!
</para>
<para>
Just prep the rocket for flight, then power up the altimeter
- in "idle" mode (placing air-frame horizontal for TeleMetrum or
- selected the Configure Altimeter tab for TeleMini). This will cause
- the firmware to go into "idle" mode, in which the normal flight
+ in “idle” mode (placing air-frame horizontal for TeleMetrum or TeleMega, or
+ selecting the Configure Altimeter tab for TeleMini). This will cause
+ the firmware to go into “idle” mode, in which the normal flight
state machine is disabled and charges will not fire without
manual command. You can now command the altimeter to fire the apogee
or main charges from a safe distance using your computer and
<section>
<title>Radio Link </title>
<para>
- The chip our boards are based on incorporates an RF transceiver, but
+ Our flight computers all incorporate an RF transceiver, but
it's not a full duplex system... each end can only be transmitting or
receiving at any given moment. So we had to decide how to manage the
link.
</para>
<para>
By design, the altimeter firmware listens for the radio link when
- it's in "idle mode", which
+ it's in “idle mode”, which
allows us to use the radio link to configure the rocket, do things like
ejection tests, and extract data after a flight without having to
- crack open the air-frame. However, when the board is in "flight
- mode", the altimeter only
+ crack open the air-frame. However, when the board is in “flight
+ mode”, the altimeter only
transmits and doesn't listen at all. That's because we want to put
ultimate priority on event detection and getting telemetry out of
the rocket through
data later...
</para>
<para>
- We don't use a 'normal packet radio' mode like APRS because they're
- just too inefficient. The GFSK modulation we use is FSK with the
- base-band pulses passed through a
- Gaussian filter before they go into the modulator to limit the
- transmitted bandwidth. When combined with the hardware forward error
- correction support in the cc1111 chip, this allows us to have a very
- robust 38.4 kilobit data link with only 10 milliwatts of transmit
- power, a whip antenna in the rocket, and a hand-held Yagi on the
- ground. We've had flights to above 21k feet AGL with great reception,
- and calculations suggest we should be good to well over 40k feet AGL
- with a 5-element yagi on the ground. We hope to fly boards to higher
- altitudes over time, and would of course appreciate customer feedback
- on performance in higher altitude flights!
+ We don't generally use a 'normal packet radio' mode like APRS
+ because they're just too inefficient. The GFSK modulation we
+ use is FSK with the base-band pulses passed through a Gaussian
+ filter before they go into the modulator to limit the
+ transmitted bandwidth. When combined with forward error
+ correction and interleaving, this allows us to have a very
+ robust 19.2 kilobit data link with only 10-40 milliwatts of
+ transmit power, a whip antenna in the rocket, and a hand-held
+ Yagi on the ground. We've had flights to above 21k feet AGL
+ with great reception, and calculations suggest we should be
+ good to well over 40k feet AGL with a 5-element yagi on the
+ ground with our 10mW units and over 100k feet AGL with the
+ 40mW devices. We hope to fly boards to higher altitudes over
+ time, and would of course appreciate customer feedback on
+ performance in higher altitude flights!
+ </para>
+ </section>
+ <section>
+ <title>APRS</title>
+ <para>
+ TeleMetrum v2.0 and TeleMega can send APRS if desired, and the
+ interval between APRS packets can be configured. As each APRS
+ packet takes a full second to transmit, we recommend an
+ interval of at least 5 seconds to avoid consuming too much
+ battery power or radio channel bandwidth. You can configure
+ the APRS interval using AltosUI; that process is described in
+ the Configure Altimeter section of the AltosUI chapter.
+ </para>
+ <para>
+ AltOS uses the APRS compressed position report data format,
+ which provides for higher position precision and shorter
+ packets than the original APRS format. It also includes
+ altitude data, which is invaluable when tracking rockets. We
+ haven't found a receiver which doesn't handle compressed
+ positions, but it's just possible that you have one, so if you
+ have an older device that can receive the raw packets but
+ isn't displaying position information, it's possible that this
+ is the cause.
+ </para>
+ <para>
+ The APRS packet format includes a comment field that can have
+ arbitrary text in it. AltOS uses this to send status
+ information about the flight computer. It sends four fields as
+ shown in the following table.
+ </para>
+ <table frame='all'>
+ <title>Altus Metrum APRS Comments</title>
+ <?dbfo keep-together="always"?>
+ <tgroup cols='3' align='center' colsep='1' rowsep='1'>
+ <colspec align='center' colwidth='*' colname='Field'/>
+ <colspec align='center' colwidth='*' colname='Example'/>
+ <colspec align='center' colwidth='4*' colname='Description'/>
+ <thead>
+ <row>
+ <entry align='center'>Field</entry>
+ <entry align='center'>Example</entry>
+ <entry align='center'>Description</entry>
+ </row>
+ </thead>
+ <tbody>
+ <row>
+ <entry>1</entry>
+ <entry>L</entry>
+ <entry>GPS Status U for unlocked, L for locked</entry>
+ </row>
+ <row>
+ <entry>2</entry>
+ <entry>6</entry>
+ <entry>Number of Satellites in View</entry>
+ </row>
+ <row>
+ <entry>3</entry>
+ <entry>B4.0</entry>
+ <entry>Altimeter Battery Voltage</entry>
+ </row>
+ <row>
+ <entry>4</entry>
+ <entry>A3.7</entry>
+ <entry>Apogee Igniter Voltage</entry>
+ </row>
+ <row>
+ <entry>5</entry>
+ <entry>M3.7</entry>
+ <entry>Main Igniter Voltage</entry>
+ </row>
+ </tbody>
+ </tgroup>
+ </table>
+ <para>
+ Here's an example of an APRS comment showing GPS lock with 6
+ satellites in view, a primary battery at 4.0V, and
+ apogee and main igniters both at 3.7V.
+ <screen>
+ L6 B4.0 A3.7 M3.7
+ </screen>
+ </para>
+ <para>
+ Make sure your primary battery is above 3.8V, any connected
+ igniters are above 3.5V and GPS is locked with at least 5 or 6
+ satellites in view before flying. If GPS is switching between
+ L and U regularly, then it doesn't have a good lock and you
+ should wait until it becomes stable.
+ </para>
+ <para>
+ If the GPS receiver loses lock, the APRS data transmitted will
+ contain the last position for which GPS lock was
+ available. You can tell that this has happened by noticing
+ that the GPS status character switches from 'L' to 'U'. Before
+ GPS has locked, APRS will transmit zero for latitude,
+ longitude and altitude.
</para>
</section>
<section>
<title>Configurable Parameters</title>
<para>
Configuring an Altus Metrum altimeter for flight is very
- simple. Even on our baro-only TeleMini board, the use of a Kalman
- filter means there is no need to set a "mach delay". The few
- configurable parameters can all be set using AltosUI over USB or
- or radio link via TeleDongle.
+ simple. Even on our baro-only TeleMini and EasyMini boards,
+ the use of a Kalman filter means there is no need to set a
+ “mach delay”. The few configurable parameters can all be set
+ using AltosUI over USB or or radio link via TeleDongle. Read
+ the Configure Altimeter section in the AltosUI chapter below
+ for more information.
</para>
<section>
- <title>Radio Frequencies</title>
+ <title>Radio Frequency</title>
<para>
Altus Metrum boards support radio frequencies in the 70cm
band. By default, the configuration interface provides a
- list of 10 "standard" frequencies in 100kHz channels starting at
+ list of 10 “standard” frequencies in 100kHz channels starting at
434.550MHz. However, the firmware supports use of
any 50kHz multiple within the 70cm band. At any given
launch, we highly recommend coordinating when and by whom each
altimeter and TeleDongle must be configured to the same
frequency to successfully communicate with each other.
</para>
- <para>
- To set the radio frequency, use the 'c R' command to specify the
- radio transceiver configuration parameter. This parameter is computed
- using the desired frequency, 'F', the radio calibration parameter, 'C' (showed by the 'c s' command) and
- the standard calibration reference frequency, 'S', (normally 434.550MHz):
- <programlisting>
- R = F / S * C
- </programlisting>
- Round the result to the nearest integer value.
- As with all 'c' sub-commands, follow this with a 'c w' to write the
- change to the parameter block in the on-board flash on
- your altimeter board if you want the change to stay in place across reboots.
- </para>
+ </section>
+ <section>
+ <title>Callsign</title>
+ <para>
+ This sets the callsign used for telemetry, APRS and the
+ packet link. For telemetry and APRS, this is used to
+ identify the device. For the packet link, the callsign must
+ match that configured in AltosUI or the link will not
+ work. This is to prevent accidental configuration of another
+ Altus Metrum flight computer operating on the same frequency nearby.
+ </para>
+ </section>
+ <section>
+ <title>Telemetry/RDF/APRS Enable</title>
+ <para>
+ You can completely disable the radio while in flight, if
+ necessary. This doesn't disable the packet link in idle
+ mode.
+ </para>
+ </section>
+ <section>
+ <title>APRS Interval</title>
+ <para>
+ This selects how often APRS packets are transmitted. Set
+ this to zero to disable APRS without also disabling the
+ regular telemetry and RDF transmissions. As APRS takes a
+ full second to transmit a single position report, we
+ recommend sending packets no more than once every 5 seconds.
+ </para>
</section>
<section>
<title>Apogee Delay</title>
primary and backup pyrotechnic charges do not fire simultaneously.
</para>
<para>
- To set the apogee delay, use the 'c d' command.
- As with all 'c' sub-commands, follow this with a 'c w' to write the
- change to the parameter block in the on-board DataFlash chip.
- </para>
- <para>
- Please note that the Altus Metrum apogee detection algorithm
- fires exactly at apogee. If you are also flying an
- altimeter like the PerfectFlite MAWD, which only supports
- selecting 0 or 1 seconds of apogee delay, you may wish to
- set the MAWD to 0 seconds delay and set the TeleMetrum to
- fire your backup 2 or 3 seconds later to avoid any chance of
- both charges firing simultaneously. We've flown several
- air-frames this way quite happily, including Keith's
- successful L3 cert.
+ The Altus Metrum apogee detection algorithm fires exactly at
+ apogee. If you are also flying an altimeter like the
+ PerfectFlite MAWD, which only supports selecting 0 or 1
+ seconds of apogee delay, you may wish to set the MAWD to 0
+ seconds delay and set the TeleMetrum to fire your backup 2
+ or 3 seconds later to avoid any chance of both charges
+ firing simultaneously. We've flown several air-frames this
+ way quite happily, including Keith's successful L3 cert.
</para>
</section>
+ <section>
+ <title>Apogee Lockout</title>
+ <para>
+ Apogee lockout is the number of seconds after boost where
+ the flight computer will not fire the apogee charge, even if
+ the rocket appears to be at apogee. This is often called
+ 'Mach Delay', as it is intended to prevent a flight computer
+ from unintentionally firing apogee charges due to the pressure
+ spike that occurrs across a mach transition. Altus Metrum
+ flight computers include a Kalman filter which is not fooled
+ by this sharp pressure increase, and so this setting should
+ be left at the default value of zero to disable it.
+ </para>
+ </section>
<section>
<title>Main Deployment Altitude</title>
<para>
than the primary so that both pyrotechnic charges don't fire
simultaneously.
</para>
- <para>
- To set the main deployment altitude, use the 'c m' command.
- As with all 'c' sub-commands, follow this with a 'c w' to write the
- change to the parameter block in the on-board DataFlash chip.
- </para>
</section>
- </section>
- <section>
- <title>Calibration</title>
- <para>
- There are only two calibrations required for a TeleMetrum board, and
- only one for TeleDongle and TeleMini.
- </para>
<section>
- <title>Radio Frequency</title>
- <para>
- The radio frequency is synthesized from a clock based on the 48 MHz
- crystal on the board. The actual frequency of this oscillator must be
- measured to generate a calibration constant. While our GFSK modulation
- bandwidth is wide enough to allow boards to communicate even when
- their oscillators are not on exactly the same frequency, performance
- is best when they are closely matched.
- Radio frequency calibration requires a calibrated frequency counter.
- Fortunately, once set, the variation in frequency due to aging and
- temperature changes is small enough that re-calibration by customers
- should generally not be required.
- </para>
- <para>
- To calibrate the radio frequency, connect the UHF antenna port to a
- frequency counter, set the board to 434.550MHz, and use the 'C'
- command to generate a CW carrier. Wait for the transmitter temperature
- to stabilize and the frequency to settle down.
- Then, divide 434.550 MHz by the
- measured frequency and multiply by the current radio cal value show
- in the 'c s' command. For an unprogrammed board, the default value
- is 1186611. Take the resulting integer and program it using the 'c f'
- command. Testing with the 'C' command again should show a carrier
- within a few tens of Hertz of the intended frequency.
- As with all 'c' sub-commands, follow this with a 'c w' to write the
- change to the parameter block in the on-board DataFlash chip.
- </para>
+ <title>Maximum Flight Log</title>
+ <para>
+ Changing this value will set the maximum amount of flight
+ log storage that an individual flight will use. The
+ available storage is divided into as many flights of the
+ specified size as can fit in the available space. You can
+ download and erase individual flight logs. If you fill up
+ the available storage, future flights will not get logged
+ until you erase some of the stored ones.
+ </para>
<para>
- when the radio calibration value is changed, the radio
- frequency value is reset to the same value, so you'll need
- to recompute and reset the radio frequency value using the
- new radio calibration value.
+ Even though our flight computers (except TeleMini v1.0) can store
+ multiple flights, we strongly recommend downloading and saving
+ flight data after each flight.
</para>
</section>
<section>
- <title>TeleMetrum Accelerometer</title>
- <para>
- The TeleMetrum accelerometer we use has its own 5 volt power supply and
- the output must be passed through a resistive voltage divider to match
- the input of our 3.3 volt ADC. This means that unlike the barometric
- sensor, the output of the acceleration sensor is not ratio-metric to
- the ADC converter, and calibration is required. We also support the
- use of any of several accelerometers from a Freescale family that
- includes at least +/- 40g, 50g, 100g, and 200g parts. Using gravity,
- a simple 2-point calibration yields acceptable results capturing both
- the different sensitivities and ranges of the different accelerometer
- parts and any variation in power supply voltages or resistor values
- in the divider network.
- </para>
- <para>
- To calibrate the acceleration sensor, use the 'c a 0' command. You
- will be prompted to orient the board vertically with the UHF antenna
- up and press a key, then to orient the board vertically with the
- UHF antenna down and press a key.
- As with all 'c' sub-commands, follow this with a 'c w' to write the
- change to the parameter block in the on-board DataFlash chip.
- </para>
- <para>
- The +1g and -1g calibration points are included in each telemetry
- frame and are part of the header extracted by ao-dumplog after flight.
- Note that we always store and return raw ADC samples for each
- sensor... nothing is permanently "lost" or "damaged" if the
- calibration is poor.
- </para>
- <para>
- In the unlikely event an accel cal that goes badly, it is possible
- that TeleMetrum may always come up in 'pad mode' and as such not be
- listening to either the USB or radio link. If that happens,
- there is a special hook in the firmware to force the board back
- in to 'idle mode' so you can re-do the cal. To use this hook, you
- just need to ground the SPI clock pin at power-on. This pin is
- available as pin 2 on the 8-pin companion connector, and pin 1 is
- ground. So either carefully install a fine-gauge wire jumper
- between the two pins closest to the index hole end of the 8-pin
- connector, or plug in the programming cable to the 8-pin connector
- and use a small screwdriver or similar to short the two pins closest
- to the index post on the 4-pin end of the programming cable, and
- power up the board. It should come up in 'idle mode' (two beeps).
- </para>
+ <title>Ignite Mode</title>
+ <para>
+ Instead of firing one charge at apogee and another charge at
+ a fixed height above the ground, you can configure the
+ altimeter to fire both at apogee or both during
+ descent. This was added to support an airframe Bdale designed that
+ had two altimeters, one in the fin can and one in the nose.
+ </para>
+ <para>
+ Providing the ability to use both igniters for apogee or
+ main allows some level of redundancy without needing two
+ flight computers. In Redundant Apogee or Redundant Main
+ mode, the two charges will be fired two seconds apart.
+ </para>
+ </section>
+ <section>
+ <title>Pad Orientation</title>
+ <para>
+ TeleMetrum and TeleMega measure acceleration along the axis
+ of the board. Which way the board is oriented affects the
+ sign of the acceleration value. Instead of trying to guess
+ which way the board is mounted in the air frame, the
+ altimeter must be explicitly configured for either Antenna
+ Up or Antenna Down. The default, Antenna Up, expects the end
+ of the board connected to the 70cm antenna to be nearest the
+ nose of the rocket, with the end containing the screw
+ terminals nearest the tail.
+ </para>
+ </section>
+ <section>
+ <title>Configurable Pyro Channels</title>
+ <para>
+ In addition to the usual Apogee and Main pyro channels,
+ TeleMega has four additional channels that can be configured
+ to activate when various flight conditions are
+ satisfied. You can select as many conditions as necessary;
+ all of them must be met in order to activate the
+ channel. The conditions available are:
+ </para>
+ <itemizedlist>
+ <listitem>
+ <para>
+ Acceleration away from the ground. Select a value, and
+ then choose whether acceleration should be above or
+ below that value. Acceleration is positive upwards, so
+ accelerating towards the ground would produce negative
+ numbers. Acceleration during descent is noisy and
+ inaccurate, so be careful when using it during these
+ phases of the flight.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Vertical speed. Select a value, and then choose whether
+ vertical speed should be above or below that
+ value. Speed is positive upwards, so moving towards the
+ ground would produce negative numbers. Speed during
+ descent is a bit noisy and so be careful when using it
+ during these phases of the flight.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Height. Select a value, and then choose whether the
+ height above the launch pad should be above or below
+ that value.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Orientation. TeleMega contains a 3-axis gyroscope and
+ accelerometer which is used to measure the current
+ angle. Note that this angle is not the change in angle
+ from the launch pad, but rather absolute relative to
+ gravity; the 3-axis accelerometer is used to compute the
+ angle of the rocket on the launch pad and initialize the
+ system. Because this value is computed by integrating
+ rate gyros, it gets progressively less accurate as the
+ flight goes on. It should have an accumulated error of
+ less than 0.2°/second (after 10 seconds of flight, the
+ error should be less than 2°).
+ </para>
+ <para>
+ The usual use of the orientation configuration is to
+ ensure that the rocket is traveling mostly upwards when
+ deciding whether to ignite air starts or additional
+ stages. For that, choose a reasonable maximum angle
+ (like 20°) and set the motor igniter to require an angle
+ of less than that value.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Flight Time. Time since boost was detected. Select a
+ value and choose whether to activate the pyro channel
+ before or after that amount of time.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Ascending. A simple test saying whether the rocket is
+ going up or not. This is exactly equivalent to testing
+ whether the speed is > 0.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Descending. A simple test saying whether the rocket is
+ going down or not. This is exactly equivalent to testing
+ whether the speed is < 0.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ After Motor. The flight software counts each time the
+ rocket starts accelerating (presumably due to a motor or
+ motors igniting). Use this value to count ignitions for
+ multi-staged or multi-airstart launches.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Delay. This value doesn't perform any checks, instead it
+ inserts a delay between the time when the other
+ parameters become true and when the pyro channel is
+ activated.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Flight State. The flight software tracks the flight
+ through a sequence of states:
+ <orderedlist>
+ <listitem>
+ <para>
+ Boost. The motor has lit and the rocket is
+ accelerating upwards.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Fast. The motor has burned out and the rocket is
+ decelerating, but it is going faster than 200m/s.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Coast. The rocket is still moving upwards and
+ decelerating, but the speed is less than 200m/s.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Drogue. The rocket has reached apogee and is heading
+ back down, but is above the configured Main
+ altitude.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Main. The rocket is still descending, and is below
+ the Main altitude
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Landed. The rocket is no longer moving.
+ </para>
+ </listitem>
+ </orderedlist>
+ </para>
+ <para>
+ You can select a state to limit when the pyro channel
+ may activate; note that the check is based on when the
+ rocket transitions <emphasis>into</emphasis> the state, and so checking for
+ “greater than Boost” means that the rocket is currently
+ in boost or some later state.
+ </para>
+ <para>
+ When a motor burns out, the rocket enters either Fast or
+ Coast state (depending on how fast it is moving). If the
+ computer detects upwards acceleration again, it will
+ move back to Boost state.
+ </para>
+ </listitem>
+ </itemizedlist>
</section>
</section>
</chapter>
<chapter>
-
<title>AltosUI</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="altosui.png" width="4.6in"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
The AltosUI program provides a graphical user interface for
- interacting with the Altus Metrum product family, including
- TeleMetrum, TeleMini and TeleDongle. AltosUI can monitor telemetry data,
- configure TeleMetrum, TeleMini and TeleDongle devices and many other
+ interacting with the Altus Metrum product family. AltosUI can
+ monitor telemetry data, configure devices and many other
tasks. The primary interface window provides a selection of
- buttons, one for each major activity in the system. This manual
- is split into chapters, each of which documents one of the tasks
+ buttons, one for each major activity in the system. This chapter
+ is split into sections, each of which documents one of the tasks
provided from the top-level toolbar.
</para>
<section>
AltosUI will create a window to display telemetry data as
received by the selected TeleDongle device.
</para>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="device-selection.png" width="3.1in"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
All telemetry data received are automatically recorded in
suitable log files. The name of the files includes the current
you know how strong a signal TeleDongle is receiving. The
radio inside TeleDongle operates down to about -99dBm;
weaker signals may not be receivable. The packet link uses
- error correction and detection techniques which prevent
+ error detection and correction techniques which prevent
incorrect data from being reported.
</para>
</listitem>
+ <listitem>
+ <para>
+ The age of the displayed data, in seconds since the last
+ successfully received telemetry packet. In normal operation
+ this will stay in the low single digits. If the number starts
+ counting up, then you are no longer receiving data over the radio
+ link from the flight computer.
+ </para>
+ </listitem>
</itemizedlist>
<para>
Finally, the largest portion of the window contains a set of
They're arranged in 'flight order' so that as the flight
progresses, the selected tab automatically switches to display
data relevant to the current state of the flight. You can select
- other tabs at any time. The final 'table' tab contains all of
- the telemetry data in one place.
+ other tabs at any time. The final 'table' tab displays all of
+ the raw telemetry values in one place in a spreadsheet-like format.
</para>
<section>
<title>Launch Pad</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="launch-pad.png" width="5.5in"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
The 'Launch Pad' tab shows information used to decide when the
rocket is ready for flight. The first elements include red/green
indicators, if any of these is red, you'll want to evaluate
whether the rocket is ready to launch:
- <itemizedlist>
- <listitem>
- <para>
- Battery Voltage. This indicates whether the Li-Po battery
- powering the TeleMetrum has sufficient charge to last for
- the duration of the flight. A value of more than
- 3.7V is required for a 'GO' status.
- </para>
- </listitem>
- <listitem>
- <para>
- Apogee Igniter Voltage. This indicates whether the apogee
- igniter has continuity. If the igniter has a low
- resistance, then the voltage measured here will be close
- to the Li-Po battery voltage. A value greater than 3.2V is
- required for a 'GO' status.
- </para>
- </listitem>
- <listitem>
- <para>
- Main Igniter Voltage. This indicates whether the main
- igniter has continuity. If the igniter has a low
- resistance, then the voltage measured here will be close
- to the Li-Po battery voltage. A value greater than 3.2V is
- required for a 'GO' status.
- </para>
- </listitem>
- <listitem>
- <para>
- On-board Data Logging. This indicates whether there is
- space remaining on-board to store flight data for the
- upcoming flight. If you've downloaded data, but failed
- to erase flights, there may not be any space
- left. TeleMetrum can store multiple flights, depending
- on the configured maximum flight log size. TeleMini
- stores only a single flight, so it will need to be
- downloaded and erased after each flight to capture
- data. This only affects on-board flight logging; the
- altimeter will still transmit telemetry and fire
- ejection charges at the proper times.
- </para>
- </listitem>
- <listitem>
- <para>
- GPS Locked. For a TeleMetrum device, this indicates whether the GPS receiver is
- currently able to compute position information. GPS requires
- at least 4 satellites to compute an accurate position.
- </para>
- </listitem>
- <listitem>
- <para>
- GPS Ready. For a TeleMetrum device, this indicates whether GPS has reported at least
- 10 consecutive positions without losing lock. This ensures
- that the GPS receiver has reliable reception from the
- satellites.
- </para>
- </listitem>
- </itemizedlist>
- <para>
- The Launchpad tab also shows the computed launch pad position
- and altitude, averaging many reported positions to improve the
- accuracy of the fix.
- </para>
+ <variablelist>
+ <varlistentry>
+ <term>Battery Voltage</term>
+ <listitem>
+ <para>
+ This indicates whether the Li-Po battery powering the
+ flight computer has sufficient charge to last for
+ the duration of the flight. A value of more than
+ 3.8V is required for a 'GO' status.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Apogee Igniter Voltage</term>
+ <listitem>
+ <para>
+ This indicates whether the apogee
+ igniter has continuity. If the igniter has a low
+ resistance, then the voltage measured here will be close
+ to the Li-Po battery voltage. A value greater than 3.2V is
+ required for a 'GO' status.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Main Igniter Voltage</term>
+ <listitem>
+ <para>
+ This indicates whether the main
+ igniter has continuity. If the igniter has a low
+ resistance, then the voltage measured here will be close
+ to the Li-Po battery voltage. A value greater than 3.2V is
+ required for a 'GO' status.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>On-board Data Logging</term>
+ <listitem>
+ <para>
+ This indicates whether there is
+ space remaining on-board to store flight data for the
+ upcoming flight. If you've downloaded data, but failed
+ to erase flights, there may not be any space
+ left. Most of our flight computers can store multiple
+ flights, depending on the configured maximum flight log
+ size. TeleMini v1.0 stores only a single flight, so it
+ will need to be
+ downloaded and erased after each flight to capture
+ data. This only affects on-board flight logging; the
+ altimeter will still transmit telemetry and fire
+ ejection charges at the proper times even if the flight
+ data storage is full.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>GPS Locked</term>
+ <listitem>
+ <para>
+ For a TeleMetrum or TeleMega device, this indicates whether the GPS receiver is
+ currently able to compute position information. GPS requires
+ at least 4 satellites to compute an accurate position.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>GPS Ready</term>
+ <listitem>
+ <para>
+ For a TeleMetrum or TeleMega device, this indicates whether GPS has reported at least
+ 10 consecutive positions without losing lock. This ensures
+ that the GPS receiver has reliable reception from the
+ satellites.
+ </para>
+ </listitem>
+ </varlistentry>
+ </variablelist>
</para>
+ <para>
+ The Launchpad tab also shows the computed launch pad position
+ and altitude, averaging many reported positions to improve the
+ accuracy of the fix.
+ </para>
</section>
<section>
<title>Ascent</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="ascent.png" width="5.5in"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
This tab is shown during Boost, Fast and Coast
phases. The information displayed here helps monitor the
rocket as it heads towards apogee.
</para>
<para>
- The height, speed and acceleration are shown along with the
- maximum values for each of them. This allows you to quickly
- answer the most commonly asked questions you'll hear during
- flight.
+ The height, speed, acceleration and tilt are shown along
+ with the maximum values for each of them. This allows you to
+ quickly answer the most commonly asked questions you'll hear
+ during flight.
</para>
<para>
- The current latitude and longitude reported by the TeleMetrum GPS are
+ The current latitude and longitude reported by the GPS are
also shown. Note that under high acceleration, these values
may not get updated as the GPS receiver loses position
fix. Once the rocket starts coasting, the receiver should
</section>
<section>
<title>Descent</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="descent.png" width="5.5in"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
Once the rocket has reached apogee and (we hope) activated the
apogee charge, attention switches to tracking the rocket on
<para>
To monitor whether the apogee charge operated correctly, the
current descent rate is reported along with the current
- height. Good descent rates generally range from 15-30m/s.
+ height. Good descent rates vary based on the choice of recovery
+ components, but generally range from 15-30m/s on drogue and should
+ be below 10m/s when under the main parachute in a dual-deploy flight.
</para>
<para>
- For TeleMetrum altimeters, you can locate the rocket in the sky
- using the elevation and
- bearing information to figure out where to look. Elevation is
- in degrees above the horizon. Bearing is reported in degrees
- relative to true north. Range can help figure out how big the
- rocket will appear. Note that all of these values are relative
- to the pad location. If the elevation is near 90°, the rocket
- is over the pad, not over you.
+ With GPS-equipped flight computers, you can locate the rocket in the
+ sky using the elevation and bearing information to figure
+ out where to look. Elevation is in degrees above the
+ horizon. Bearing is reported in degrees relative to true
+ north. Range can help figure out how big the rocket will
+ appear. Ground Distance shows how far it is to a point
+ directly under the rocket and can help figure out where the
+ rocket is likely to land. Note that all of these values are
+ relative to the pad location. If the elevation is near 90°,
+ the rocket is over the pad, not over you.
</para>
<para>
Finally, the igniter voltages are reported in this tab as
well, both to monitor the main charge as well as to see what
- the status of the apogee charge is.
+ the status of the apogee charge is. Note that some commercial
+ e-matches are designed to retain continuity even after being
+ fired, and will continue to show as green or return from red to
+ green after firing.
</para>
</section>
<section>
<title>Landed</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="landed.png" width="5.5in"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
Once the rocket is on the ground, attention switches to
- recovery. While the radio signal is generally lost once the
+ recovery. While the radio signal is often lost once the
rocket is on the ground, the last reported GPS position is
generally within a short distance of the actual landing location.
</para>
The last reported GPS position is reported both by
latitude and longitude as well as a bearing and distance from
the launch pad. The distance should give you a good idea of
- whether you'll want to walk or hitch a ride. Take the reported
+ whether to walk or hitch a ride. Take the reported
latitude and longitude and enter them into your hand-held GPS
unit and have that compute a track to the landing location.
</para>
<para>
- Both TeleMini and TeleMetrum will continue to transmit RDF
+ Our flight computers will continue to transmit RDF
tones after landing, allowing you to locate the rocket by
- following the radio signal. You may need to get away from
- the clutter of the flight line, or even get up on a hill (or
- your neighbor's RV) to receive the RDF signal.
+ following the radio signal if necessary. You may need to get
+ away from the clutter of the flight line, or even get up on
+ a hill (or your neighbor's RV roof) to receive the RDF signal.
</para>
<para>
The maximum height, speed and acceleration reported
during the flight are displayed for your admiring observers.
+ The accuracy of these immediate values depends on the quality
+ of your radio link and how many packets were received.
+ Recovering the on-board data after flight may yield
+ more precise results.
</para>
<para>
To get more detailed information about the flight, you can
graph window for the current flight.
</para>
</section>
+ <section>
+ <title>Table</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="table.png" width="5.5in"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ The table view shows all of the data available from the
+ flight computer. Probably the most useful data on
+ this tab is the detailed GPS information, which includes
+ horizontal dilution of precision information, and
+ information about the signal being received from the satellites.
+ </para>
+ </section>
<section>
<title>Site Map</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="site-map.png" width="5.5in"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
- When the TeleMetrum gets a GPS fix, the Site Map tab will map
+ When the TeleMetrum has a GPS fix, the Site Map tab will map
the rocket's position to make it easier for you to locate the
rocket, both while it is in the air, and when it has landed. The
rocket's state is indicated by color: white for pad, red for
dark blue for main, and black for landed.
</para>
<para>
- The map's scale is approximately 3m (10ft) per pixel. The map
+ The map's default scale is approximately 3m (10ft) per pixel. The map
can be dragged using the left mouse button. The map will attempt
to keep the rocket roughly centered while data is being received.
</para>
+ <para>
+ You can adjust the style of map and the zoom level with
+ buttons on the right side of the map window. You can draw a
+ line on the map by moving the mouse over the map with a
+ button other than the left one pressed, or by pressing the
+ left button while also holding down the shift key. The
+ length of the line in real-world units will be shown at the
+ start of the line.
+ </para>
<para>
Images are fetched automatically via the Google Maps Static API,
- and are cached for reuse. If map images cannot be downloaded,
+ and cached on disk for reuse. If map images cannot be downloaded,
the rocket's path will be traced on a dark gray background
instead.
</para>
before you leave home; check out the 'Preload Maps' section below.
</para>
</section>
+ <section>
+ <title>Ignitor</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="ignitor.png" width="5.5in"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ TeleMega includes four additional programmable pyro
+ channels. The Ignitor tab shows whether each of them has
+ continuity. If an ignitor has a low resistance, then the
+ voltage measured here will be close to the pyro battery
+ voltage. A value greater than 3.2V is required for a 'GO'
+ status.
+ </para>
+ </section>
</section>
<section>
<title>Save Flight Data</title>
<para>
The altimeter records flight data to its internal flash memory.
- The TeleMetrum data is recorded at a much higher rate than the telemetry
+ TeleMetrum data is recorded at a much higher rate than the telemetry
system can handle, and is not subject to radio drop-outs. As
such, it provides a more complete and precise record of the
flight. The 'Save Flight Data' button allows you to read the
- flash memory and write it to disk. As TeleMini has only a barometer, it
- records data at the same rate as the telemetry signal, but there will be
- no data lost due to telemetry drop-outs.
+ flash memory and write it to disk.
</para>
<para>
Clicking on the 'Save Flight Data' button brings up a list of
- connected TeleMetrum and TeleDongle devices. If you select a
- TeleMetrum device, the flight data will be downloaded from that
+ connected flight computers and TeleDongle devices. If you select a
+ flight computer, the flight data will be downloaded from that
device directly. If you select a TeleDongle device, flight data
- will be downloaded from a TeleMetrum or TeleMini device connected via the
- packet command link to the specified TeleDongle. See the chapter
- on Packet Command Mode for more information about this.
+ will be downloaded from a flight computer over radio link via the
+ specified TeleDongle. See the chapter on Controlling An Altimeter
+ Over The Radio Link for more information.
</para>
<para>
After the device has been selected, a dialog showing the
select which flights to download and which to delete. With
version 0.9 or newer firmware, you must erase flights in order
for the space they consume to be reused by another
- flight. This prevents you from accidentally losing flight data
+ flight. This prevents accidentally losing flight data
if you neglect to download data before flying again. Note that
if there is no more space available in the device, then no
- data will be recorded for a flight.
+ data will be recorded during the next flight.
</para>
<para>
The file name for each flight log is computed automatically
flash memory.
</para>
<para>
- Once a flight record is selected, a window with two tabs is
- opened. The first tab contains a graph with acceleration
- (blue), velocity (green) and altitude (red) of the flight are
- plotted and displayed, measured in metric units. The
- apogee(yellow) and main(magenta) igniter voltages are also
- displayed; high voltages indicate continuity, low voltages
- indicate open circuits. The second tab contains some basic
- flight statistics.
+ Note that telemetry files will generally produce poor graphs
+ due to the lower sampling rate and missed telemetry packets.
+ Use saved flight data in .eeprom files for graphing where possible.
+ </para>
+ <para>
+ Once a flight record is selected, a window with multiple tabs is
+ opened.
</para>
+ <section>
+ <title>Flight Graph</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="graph.png" width="6in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ By default, the graph contains acceleration (blue),
+ velocity (green) and altitude (red).
+ </para>
<para>
The graph can be zoomed into a particular area by clicking and
dragging down and to the right. Once zoomed, the graph can be
The right mouse button causes a pop-up menu to be displayed, giving
you the option save or print the plot.
</para>
- <para>
- Note that telemetry files will generally produce poor graphs
- due to the lower sampling rate and missed telemetry packets.
- Use saved flight data for graphing where possible.
- </para>
+ </section>
+ <section>
+ <title>Configure Graph</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="graph-configure.png" width="6in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ This selects which graph elements to show, and, at the
+ very bottom, lets you switch between metric and
+ imperial units
+ </para>
+ </section>
+ <section>
+ <title>Flight Statistics</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="graph-stats.png" width="6in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ Shows overall data computed from the flight.
+ </para>
+ </section>
+ <section>
+ <title>Map</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="graph-map.png" width="6in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ Shows a satellite image of the flight area overlaid
+ with the path of the flight. The red concentric
+ circles mark the launch pad, the black concentric
+ circles mark the landing location.
+ </para>
+ </section>
</section>
<section>
<title>Export Data</title>
<para>
This tool takes the raw data files and makes them available for
- external analysis. When you select this button, you are prompted to select a flight
- data file (either .eeprom or .telem will do, remember that
- .eeprom files contain higher resolution and more continuous
- data). Next, a second dialog appears which is used to select
+ external analysis. When you select this button, you are prompted to
+ select a flight data file, which can be either a .eeprom or .telem.
+ The .eeprom files contain higher resolution and more continuous data,
+ while .telem files contain receiver signal strength information.
+ Next, a second dialog appears which is used to select
where to write the resulting file. It has a selector to choose
between CSV and KML file formats.
</para>
configuration information from the altimeter, then
there is a single header line which labels all of the
fields. All of these lines start with a '#' character which
- most tools can be configured to skip over.
+ many tools can be configured to skip over.
</para>
<para>
The remaining lines of the file contain the data, with each
<section>
<title>Keyhole Markup Language (for Google Earth)</title>
<para>
- This is the format used by
- Googleearth to provide an overlay within that
- application. With this, you can use Googleearth to see the
- whole flight path in 3D.
+ This is the format used by Google Earth to provide an overlay
+ within that application. With this, you can use Google Earth to
+ see the whole flight path in 3D.
</para>
</section>
</section>
<section>
<title>Configure Altimeter</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="configure-altimeter.png" width="3.6in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
- Select this button and then select either a TeleMetrum or
+ Select this button and then select either an altimeter or
TeleDongle Device from the list provided. Selecting a TeleDongle
- device will use Packet Command Mode to configure a remote
- altimeter. Learn how to use this in the Packet Command
- Mode chapter.
+ device will use the radio link to configure a remote altimeter.
</para>
<para>
The first few lines of the dialog provide information about the
<para>
At the bottom of the dialog, there are four buttons:
</para>
- <itemizedlist>
- <listitem>
- <para>
- Save. This writes any changes to the
- configuration parameter block in flash memory. If you don't
- press this button, any changes you make will be lost.
- </para>
- </listitem>
- <listitem>
- <para>
- Reset. This resets the dialog to the most recently saved values,
- erasing any changes you have made.
- </para>
- </listitem>
- <listitem>
- <para>
- Reboot. This reboots the device. Use this to
- switch from idle to pad mode by rebooting once the rocket is
- oriented for flight.
- </para>
- </listitem>
- <listitem>
- <para>
- Close. This closes the dialog. Any unsaved changes will be
- lost.
- </para>
- </listitem>
- </itemizedlist>
+ <variablelist>
+ <varlistentry>
+ <term>Save</term>
+ <listitem>
+ <para>
+ This writes any changes to the
+ configuration parameter block in flash memory. If you don't
+ press this button, any changes you make will be lost.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Reset</term>
+ <listitem>
+ <para>
+ This resets the dialog to the most recently saved values,
+ erasing any changes you have made.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Reboot</term>
+ <listitem>
+ <para>
+ This reboots the device. Use this to
+ switch from idle to pad mode by rebooting once the rocket is
+ oriented for flight, or to confirm changes you think you saved
+ are really saved.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Close</term>
+ <listitem>
+ <para>
+ This closes the dialog. Any unsaved changes will be
+ lost.
+ </para>
+ </listitem>
+ </varlistentry>
+ </variablelist>
<para>
The rest of the dialog contains the parameters to be configured.
</para>
<para>
When flying redundant electronics, it's often important to
ensure that multiple apogee charges don't fire at precisely
- the same time as that can over pressurize the apogee deployment
+ the same time, as that can over pressurize the apogee deployment
bay and cause a structural failure of the air-frame. The Apogee
Delay parameter tells the flight computer to fire the apogee
charge a certain number of seconds after apogee has been
</para>
</section>
<section>
- <title>Radio Frequency</title>
+ <title>Apogee Lockoug</title>
+ <para>
+ Apogee lockout is the number of seconds after boost where
+ the flight computer will not fire the apogee charge, even if
+ the rocket appears to be at apogee. This is often called
+ 'Mach Delay', as it is intended to prevent a flight computer
+ from unintentionally firing apogee charges due to the pressure
+ spike that occurrs across a mach transition. Altus Metrum
+ flight computers include a Kalman filter which is not fooled
+ by this sharp pressure increase, and so this setting should
+ be left at the default value of zero to disable it.
+ </para>
+ </section>
+ <section>
+ <title>Frequency</title>
<para>
- This configures which of the configured frequencies to use for both
+ This configures which of the frequencies to use for both
telemetry and packet command mode. Note that if you set this
- value via packet command mode, you will have to reconfigure
- the TeleDongle frequency before you will be able to use packet
- command mode again.
+ value via packet command mode, the TeleDongle frequency will
+ also be automatically reconfigured to match so that
+ communication will continue afterwards.
</para>
</section>
<section>
- <title>Radio Calibration</title>
+ <title>RF Calibration</title>
<para>
The radios in every Altus Metrum device are calibrated at the
factory to ensure that they transmit and receive on the
- specified frequency. You can adjust that
- calibration by changing this value. To change the TeleDongle's
- calibration, you must reprogram the unit completely.
+ specified frequency. If you need to you can adjust the calibration
+ by changing this value. Do not do this without understanding what
+ the value means, read the appendix on calibration and/or the source
+ code for more information. To change a TeleDongle's calibration,
+ you must reprogram the unit completely.
</para>
</section>
+ <section>
+ <title>Telemetry/RDF/APRS Enable</title>
+ <para>
+ Enables the radio for transmission during flight. When
+ disabled, the radio will not transmit anything during flight
+ at all.
+ </para>
+ </section>
+ <section>
+ <title>APRS Interval</title>
+ <para>
+ How often to transmit GPS information via APRS (in
+ seconds). When set to zero, APRS transmission is
+ disabled. This option is available on TeleMetrum v2 and
+ TeleMega boards. TeleMetrum v1 boards cannot transmit APRS
+ packets. Note that a single APRS packet takes nearly a full
+ second to transmit, so enabling this option will prevent
+ sending any other telemetry during that time.
+ </para>
+ </section>
<section>
<title>Callsign</title>
<para>
size. A smaller value will allow more flights to be stored,
a larger value will record data from longer flights.
</para>
+ </section>
+ <section>
+ <title>Ignitor Firing Mode</title>
<para>
- During ascent, TeleMetrum records barometer and
- accelerometer values 100 times per second, other analog
- information (voltages and temperature) 6 times per second
- and GPS data once per second. During descent, the non-GPS
- data is recorded 1/10th as often. Each barometer +
- accelerometer record takes 8 bytes.
- </para>
- <para>
- The default, 192kB, will store over 200 seconds of data at
- the ascent rate, or over 2000 seconds of data at the descent
- rate. That's plenty for most flights. This leaves enough
- storage for five flights in a 1MB system, or 10 flights in a
- 2MB system.
+ This configuration parameter allows the two standard ignitor
+ channels (Apogee and Main) to be used in different
+ configurations.
</para>
+ <variablelist>
+ <varlistentry>
+ <term>Dual Deploy</term>
+ <listitem>
+ <para>
+ This is the usual mode of operation; the
+ 'apogee' channel is fired at apogee and the 'main'
+ channel at the height above ground specified by the
+ 'Main Deploy Altitude' during descent.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Redundant Apogee</term>
+ <listitem>
+ <para>
+ This fires both channels at
+ apogee, the 'apogee' channel first followed after a two second
+ delay by the 'main' channel.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Redundant Main</term>
+ <listitem>
+ <para>
+ This fires both channels at the
+ height above ground specified by the Main Deploy
+ Altitude setting during descent. The 'apogee'
+ channel is fired first, followed after a two second
+ delay by the 'main' channel.
+ </para>
+ </listitem>
+ </varlistentry>
+ </variablelist>
+ </section>
+ <section>
+ <title>Pad Orientation</title>
<para>
- The configuration block takes the last available block of
- memory, on v1.0 boards that's just 256 bytes. However, the
- flash part on the v1.1 boards uses 64kB for each block.
- </para>
- <para>
- TeleMini has 5kB of on-board storage, which is plenty for a
- single flight. Make sure you download and delete the data
- before a subsequent flight or it will not log any data.
+ Because they include accelerometers, TeleMetrum and
+ TeleMega are sensitive to the orientation of the board. By
+ default, they expect the antenna end to point forward. This
+ parameter allows that default to be changed, permitting the
+ board to be mounted with the antenna pointing aft instead.
</para>
+ <variablelist>
+ <varlistentry>
+ <term>Antenna Up</term>
+ <listitem>
+ <para>
+ In this mode, the antenna end of the
+ flight computer must point forward, in line with the
+ expected flight path.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Antenna Down</term>
+ <listitem>
+ <para>
+ In this mode, the antenna end of the
+ flight computer must point aft, in line with the
+ expected flight path.
+ </para>
+ </listitem>
+ </varlistentry>
+ </variablelist>
</section>
<section>
- <title>Ignite Mode</title>
+ <title>Beeper Frequency</title>
<para>
- TeleMetrum and TeleMini provide two igniter channels as they
- were originally designed as dual-deploy flight
- computers. This configuration parameter allows the two
- channels to be used in different configurations.
+ The beeper on all Altus Metrum flight computers works best
+ at 4000Hz, however if you have more than one flight computer
+ in a single airframe, having all of them sound at the same
+ frequency can be confusing. This parameter lets you adjust
+ the base beeper frequency value.
</para>
- <itemizedlist>
- <listitem>
- <para>
- Dual Deploy. This is the usual mode of operation; the
- 'apogee' channel is fired at apogee and the 'main'
- channel at the height above ground specified by the
- 'Main Deploy Altitude' during descent.
- </para>
- </listitem>
- <listitem>
- <para>
- Redundant Apogee. This fires both channels at
- apogee, the 'apogee' channel first followed after a two second
- delay by the 'main' channel.
- </para>
- </listitem>
- <listitem>
- <para>
- Redundant Main. This fires both channels at the
- height above ground specified by the Main Deploy
- Altitude setting during descent. The 'apogee'
- channel is fired first, followed after a two second
- delay by the 'main' channel.
- </para>
- </listitem>
- </itemizedlist>
</section>
<section>
- <title>Pad Orientation</title>
+ <title>Configure Pyro Channels</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="configure-pyro.png" width="6in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
- Because it includes an accelerometer, TeleMetrum is
- sensitive to the orientation of the board. By default, it
- expects the antenna end to point forward. This parameter
- allows that default to be changed, permitting the board to
- be mounted with the antenna pointing aft instead.
+ This opens a separate window to configure the additional
+ pyro channels available on TeleMega. One column is
+ presented for each channel. Each row represents a single
+ parameter, if enabled the parameter must meet the specified
+ test for the pyro channel to be fired. See the Pyro Channels
+ section in the System Operation chapter above for a
+ description of these parameters.
+ </para>
+ <para>
+ Select conditions and set the related value; the pyro
+ channel will be activated when <emphasis>all</emphasis> of the
+ conditions are met. Each pyro channel has a separate set of
+ configuration values, so you can use different values for
+ the same condition with different channels.
+ </para>
+ <para>
+ At the bottom of the window, the 'Pyro Firing Time'
+ configuration sets the length of time (in seconds) which
+ each of these pyro channels will fire for.
+ </para>
+ <para>
+ Once you have selected the appropriate configuration for all
+ of the necessary pyro channels, you can save the pyro
+ configuration along with the rest of the flight computer
+ configuration by pressing the 'Save' button in the main
+ Configure Flight Computer window.
</para>
- <itemizedlist>
- <listitem>
- <para>
- Antenna Up. In this mode, the antenna end of the
- TeleMetrum board must point forward, in line with the
- expected flight path.
- </para>
- </listitem>
- <listitem>
- <para>
- Antenna Down. In this mode, the antenna end of the
- TeleMetrum board must point aft, in line with the
- expected flight path.
- </para>
- </listitem>
- </itemizedlist>
</section>
</section>
<section>
<title>Configure AltosUI</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="configure-altosui.png" width="2.4in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
This button presents a dialog so that you can configure the AltosUI global settings.
</para>
the current flight status. However, sometimes you don't want
to hear them.
</para>
- <itemizedlist>
- <listitem>
- <para>Enable—turns all voice announcements on and off</para>
- </listitem>
- <listitem>
- <para>
- Test Voice—Plays a short message allowing you to verify
- that the audio system is working and the volume settings
- are reasonable
- </para>
- </listitem>
- </itemizedlist>
+ <variablelist>
+ <varlistentry>
+ <term>Enable</term>
+ <listitem>
+ <para>Turns all voice announcements on and off</para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Test Voice</term>
+ <listitem>
+ <para>
+ Plays a short message allowing you to verify
+ that the audio system is working and the volume settings
+ are reasonable
+ </para>
+ </listitem>
+ </varlistentry>
+ </variablelist>
</section>
<section>
<title>Log Directory</title>
<section>
<title>Callsign</title>
<para>
- This value is used in command packet mode and is transmitted
- in each packet sent from TeleDongle and received from
- TeleMetrum. It is not used in telemetry mode as that transmits
- packets only from TeleMetrum to TeleDongle. Configure this
+ This value is transmitted in each command packet sent from
+ TeleDongle and received from an altimeter. It is not used in
+ telemetry mode, as the callsign configured in the altimeter board
+ is included in all telemetry packets. Configure this
with the AltosUI operators call sign as needed to comply with
your local radio regulations.
</para>
+ <para>
+ Note that to successfully command a flight computer over the radio
+ (to configure the altimeter, monitor idle, or fire pyro charges),
+ the callsign configured here must exactly match the callsign
+ configured in the flight computer. This matching is case
+ sensitive.
+ </para>
+ </section>
+ <section>
+ <title>Imperial Units</title>
+ <para>
+ This switches between metric units (meters) and imperial
+ units (feet and miles). This affects the display of values
+ use during flight monitoring, configuration, data graphing
+ and all of the voice announcements. It does not change the
+ units used when exporting to CSV files, those are always
+ produced in metric units.
+ </para>
</section>
<section>
<title>Font Size</title>
</section>
</section>
<section>
- <title>Flash Image</title>
+ <title>Configure Groundstation</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="configure-groundstation.png" width="3.1in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
- This reprograms any Altus Metrum device by using a TeleMetrum
- or TeleDongle as a programming dongle. Please read the
- directions for flashing devices in the Updating Device
- Firmware chapter below.
+ Select this button and then select a TeleDongle Device from the list provided.
</para>
<para>
- Once you have the programmer and target devices connected,
- push the 'Flash Image' button. That will present a dialog box
- listing all of the connected devices. Carefully select the
- programmer device, not the device to be programmed.
+ The first few lines of the dialog provide information about the
+ connected device, including the product name,
+ software version and hardware serial number. Below that are the
+ individual configuration entries.
</para>
<para>
- Next, select the image to flash to the device. These are named
- with the product name and firmware version. The file selector
- will start in the directory containing the firmware included
- with the AltosUI package. Navigate to the directory containing
- the desired firmware if it isn't there.
+ Note that the TeleDongle itself doesn't save any configuration
+ data, the settings here are recorded on the local machine in
+ the Java preferences database. Moving the TeleDongle to
+ another machine, or using a different user account on the same
+ machine will cause settings made here to have no effect.
</para>
<para>
- Next, a small dialog containing the device serial number and
- RF calibration values should appear. If these values are
- incorrect (possibly due to a corrupted image in the device),
- enter the correct values here.
+ At the bottom of the dialog, there are three buttons:
</para>
+ <variablelist>
+ <varlistentry>
+ <term>Save</term>
+ <listitem>
+ <para>
+ This writes any changes to the
+ local Java preferences file. If you don't
+ press this button, any changes you make will be lost.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Reset</term>
+ <listitem>
+ <para>
+ This resets the dialog to the most recently saved values,
+ erasing any changes you have made.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Close</term>
+ <listitem>
+ <para>
+ This closes the dialog. Any unsaved changes will be
+ lost.
+ </para>
+ </listitem>
+ </varlistentry>
+ </variablelist>
<para>
- Finally, a dialog containing a progress bar will follow the
- programming process.
+ The rest of the dialog contains the parameters to be configured.
</para>
+ <section>
+ <title>Frequency</title>
+ <para>
+ This configures the frequency to use for both telemetry and
+ packet command mode. Set this before starting any operation
+ involving packet command mode so that it will use the right
+ frequency. Telemetry monitoring mode also provides a menu to
+ change the frequency, and that menu also sets the same Java
+ preference value used here.
+ </para>
+ </section>
+ <section>
+ <title>Radio Calibration</title>
+ <para>
+ The radios in every Altus Metrum device are calibrated at the
+ factory to ensure that they transmit and receive on the
+ specified frequency. To change a TeleDongle's calibration,
+ you must reprogram the unit completely, so this entry simply
+ shows the current value and doesn't allow any changes.
+ </para>
+ </section>
+ </section>
+ <section>
+ <title>Flash Image</title>
<para>
- When programming is complete, the target device will
- reboot. Note that if the target device is connected via USB, you
- will have to unplug it and then plug it back in for the USB
- connection to reset so that you can communicate with the device
- again.
+ This reprograms Altus Metrum devices with new
+ firmware. TeleMetrum v1.x, TeleDongle, TeleMini and TeleBT are
+ all reprogrammed by using another similar unit as a
+ programming dongle (pair programming). TeleMega, TeleMetrum v2
+ and EasyMini are all programmed directly over their USB ports
+ (self programming). Please read the directions for flashing
+ devices in the Updating Device Firmware chapter below.
</para>
</section>
<section>
<title>Fire Igniter</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="fire-igniter.png" width="1.2in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
- This activates the igniter circuits in TeleMetrum to help test
- recovery systems deployment. Because this command can operate
+ This activates the igniter circuits in the flight computer to help
+ test recovery systems deployment. Because this command can operate
over the Packet Command Link, you can prepare the rocket as
for flight and then test the recovery system without needing
to snake wires inside the air-frame.
</para>
<para>
Selecting the 'Fire Igniter' button brings up the usual device
- selection dialog. Pick the desired TeleDongle or TeleMetrum
- device. This brings up another window which shows the current
- continuity test status for both apogee and main charges.
+ selection dialog. Pick the desired device. This brings up another
+ window which shows the current continuity test status for all
+ of the pyro channels.
</para>
<para>
Next, select the desired igniter to fire. This will enable the
</section>
<section>
<title>Scan Channels</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="scan-channels.png" width="3.2in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
This listens for telemetry packets on all of the configured
frequencies, displaying information about each device it
</section>
<section>
<title>Load Maps</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="load-maps.png" width="5.2in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
<para>
Before heading out to a new launch site, you can use this to
load satellite images in case you don't have internet
around the launch site, which should cover any flight you're likely to make.
</para>
<para>
- There's a drop-down menu of launch sites we know about; if
- your favorites aren't there, please let us know the lat/lon
- and name of the site. The contents of this list are actually
- downloaded at run-time, so as new sites are sent in, they'll
- get automatically added to this list.
+ There's a drop-down menu of launch sites we know about; if
+ your favorites aren't there, please let us know the lat/lon
+ and name of the site. The contents of this list are actually
+ downloaded from our server at run-time, so as new sites are sent
+ in, they'll get automatically added to this list.
+ If the launch site isn't in the list, you can manually enter the lat/lon values
+ </para>
+ <para>
+ There are four different kinds of maps you can view; you can
+ select which to download by selecting as many as you like from
+ the available types:
+ <variablelist>
+ <varlistentry>
+ <term>Hybrid</term>
+ <listitem>
+ <para>
+ A combination of satellite imagery and road data. This
+ is the default view.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Satellite</term>
+ <listitem>
+ <para>
+ Just the satellite imagery without any annotation.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Roadmap</term>
+ <listitem>
+ <para>
+ Roads, political boundaries and a few geographic features.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Terrain</term>
+ <listitem>
+ <para>
+ Contour intervals and shading that show hills and
+ valleys.
+ </para>
+ </listitem>
+ </varlistentry>
+ </variablelist>
+ </para>
+ <para>
+ You can specify the range of zoom levels to download; smaller
+ numbers show more area with less resolution. The default
+ level, 0, shows about 3m/pixel. One zoom level change
+ doubles or halves that number.
</para>
<para>
- If the launch site isn't in the list, you can manually enter the lat/lon values
+ The Tile Radius value sets how large an area around the center
+ point to download. Each tile is 512x512 pixels, and the
+ 'radius' value specifies how many tiles away from the center
+ will be downloaded. Specify a radius of 0 and you get only the
+ center tile. A radius of 1 loads a 3x3 grid, centered on the
+ specified location.
</para>
<para>
Clicking the 'Load Map' button will fetch images from Google
<title>Monitor Idle</title>
<para>
This brings up a dialog similar to the Monitor Flight UI,
- except it works with the altimeter in "idle" mode by sending
+ except it works with the altimeter in “idle” mode by sending
query commands to discover the current state rather than
- listening for telemetry packets.
+ listening for telemetry packets. Because this uses command
+ mode, it needs to have the TeleDongle and flight computer
+ callsigns match exactly. If you can receive telemetry, but
+ cannot manage to run Monitor Idle, then it's very likely that
+ your callsigns are different in some way.
+ </para>
+ </section>
+ </chapter>
+ <chapter>
+ <title>AltosDroid</title>
+ <para>
+ AltosDroid provides the same flight monitoring capabilities as
+ AltosUI, but runs on Android devices and is designed to connect
+ to a TeleBT receiver over Bluetooth™. AltosDroid monitors
+ telemetry data, logging it to internal storage in the Android
+ device, and presents that data in a UI the same way the 'Monitor
+ Flight' window does in AltosUI.
+ </para>
+ <para>
+ This manual will explain how to configure AltosDroid, connect
+ to TeleBT, operate the flight monitoring interface and describe
+ what the displayed data means.
+ </para>
+ <section>
+ <title>Installing AltosDroid</title>
+ <para>
+ AltosDroid is available from the Google Play store. To install
+ it on your Android device, open the Google Play Store
+ application and search for “altosdroid”. Make sure you don't
+ have a space between “altos” and “droid” or you probably won't
+ find what you want. That should bring you to the right page
+ from which you can download and install the application.
+ </para>
+ </section>
+ <section>
+ <title>Connecting to TeleBT</title>
+ <para>
+ Press the Android 'Menu' button or soft-key to see the
+ configuration options available. Select the 'Connect a device'
+ option and then the 'Scan for devices' entry at the bottom to
+ look for your TeleBT device. Select your device, and when it
+ asks for the code, enter '1234'.
+ </para>
+ <para>
+ Subsequent connections will not require you to enter that
+ code, and your 'paired' device will appear in the list without
+ scanning.
+ </para>
+ </section>
+ <section>
+ <title>Configuring AltosDroid</title>
+ <para>
+ The only configuration option available for AltosDroid is
+ which frequency to listen on. Press the Android 'Menu' button
+ or soft-key and pick the 'Select radio frequency' entry. That
+ brings up a menu of pre-set radio frequencies; pick the one
+ which matches your altimeter.
+ </para>
+ </section>
+ <section>
+ <title>AltosDroid Flight Monitoring</title>
+ <para>
+ AltosDroid is designed to mimic the AltosUI flight monitoring
+ display, providing separate tabs for each stage of your rocket
+ flight along with a tab containing a map of the local area
+ with icons marking the current location of the altimeter and
+ the Android device.
+ </para>
+ <section>
+ <title>Pad</title>
+ <para>
+ The 'Launch Pad' tab shows information used to decide when the
+ rocket is ready for flight. The first elements include red/green
+ indicators, if any of these is red, you'll want to evaluate
+ whether the rocket is ready to launch:
+ <variablelist>
+ <varlistentry>
+ <term>Battery Voltage</term>
+ <listitem>
+ <para>
+ This indicates whether the Li-Po battery
+ powering the TeleMetrum has sufficient charge to last for
+ the duration of the flight. A value of more than
+ 3.8V is required for a 'GO' status.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Apogee Igniter Voltage</term>
+ <listitem>
+ <para>
+ This indicates whether the apogee
+ igniter has continuity. If the igniter has a low
+ resistance, then the voltage measured here will be close
+ to the Li-Po battery voltage. A value greater than 3.2V is
+ required for a 'GO' status.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Main Igniter Voltage</term>
+ <listitem>
+ <para>
+ This indicates whether the main
+ igniter has continuity. If the igniter has a low
+ resistance, then the voltage measured here will be close
+ to the Li-Po battery voltage. A value greater than 3.2V is
+ required for a 'GO' status.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>On-board Data Logging</term>
+ <listitem>
+ <para>
+ This indicates whether there is
+ space remaining on-board to store flight data for the
+ upcoming flight. If you've downloaded data, but failed
+ to erase flights, there may not be any space
+ left. TeleMetrum can store multiple flights, depending
+ on the configured maximum flight log size. TeleMini
+ stores only a single flight, so it will need to be
+ downloaded and erased after each flight to capture
+ data. This only affects on-board flight logging; the
+ altimeter will still transmit telemetry and fire
+ ejection charges at the proper times.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>GPS Locked</term>
+ <listitem>
+ <para>
+ For a TeleMetrum or TeleMega device, this indicates whether the GPS receiver is
+ currently able to compute position information. GPS requires
+ at least 4 satellites to compute an accurate position.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>GPS Ready</term>
+ <listitem>
+ <para>
+ For a TeleMetrum or TeleMega device, this indicates whether GPS has reported at least
+ 10 consecutive positions without losing lock. This ensures
+ that the GPS receiver has reliable reception from the
+ satellites.
+ </para>
+ </listitem>
+ </varlistentry>
+ </variablelist>
+ </para>
+ <para>
+ The Launchpad tab also shows the computed launch pad position
+ and altitude, averaging many reported positions to improve the
+ accuracy of the fix.
+ </para>
+ </section>
+ </section>
+ <section>
+ <title>Downloading Flight Logs</title>
+ <para>
+ AltosDroid always saves every bit of telemetry data it
+ receives. To download that to a computer for use with AltosUI,
+ simply remove the SD card from your Android device, or connect
+ your device to your computer's USB port and browse the files
+ on that device. You will find '.telem' files in the TeleMetrum
+ directory that will work with AltosUI directly.
</para>
</section>
</chapter>
<section>
<title>In the Rocket</title>
<para>
- In the rocket itself, you just need a <ulink url="http://www.altusmetrum.org/TeleMetrum/">TeleMetrum</ulink> or
- <ulink url="http://www.altusmetrum.org/TeleMini/">TeleMini</ulink> board and
- a Li-Po rechargeable battery. An 860mAh battery weighs less than a 9V
- alkaline battery, and will run a TeleMetrum for hours.
- A 110mAh battery weighs less than a triple A battery and will run a TeleMetrum for
- a few hours, or a TeleMini for much (much) longer.
+ In the rocket itself, you just need a flight computer and
+ a single-cell, 3.7 volt nominal Li-Po rechargeable battery. An
+ 850mAh battery weighs less than a 9V alkaline battery, and will
+ run a TeleMetrum or TeleMega for hours.
+ A 110mAh battery weighs less than a triple A battery and is a good
+ choice for use with TeleMini.
</para>
<para>
- By default, we ship the altimeters with a simple wire antenna. If your
- electronics bay or the air-frame it resides within is made of carbon fiber,
- which is opaque to RF signals, you may choose to have an SMA connector
- installed so that you can run a coaxial cable to an antenna mounted
- elsewhere in the rocket.
+ By default, we ship flight computers with a simple wire antenna.
+ If your electronics bay or the air-frame it resides within is made
+ of carbon fiber, which is opaque to RF signals, you may prefer to
+ install an SMA connector so that you can run a coaxial cable to an
+ antenna mounted elsewhere in the rocket. However, note that the
+ GPS antenna is fixed on all current products, so you really want
+ to install the flight computer in a bay made of RF-transparent
+ materials if at all possible.
</para>
</section>
<section>
<title>On the Ground</title>
<para>
To receive the data stream from the rocket, you need an antenna and short
- feed-line connected to one of our <ulink url="http://www.altusmetrum.org/TeleDongle/">TeleDongle</ulink> units. The
+ feed-line connected to one of our <ulink url="http://www.altusmetrum.org/TeleDongle/">TeleDongle</ulink> units. If possible, use an SMA to BNC
+ adapter instead of feedline between the antenna feedpoint and
+ TeleDongle, as this will give you the best performance. The
TeleDongle in turn plugs directly into the USB port on a notebook
computer. Because TeleDongle looks like a simple serial port, your computer
does not require special device drivers... just plug it in.
Linux, Mac OS and Windows. There's also a suite of C tools
for Linux which can perform most of the same tasks.
</para>
+ <para>
+ Alternatively, a TeleBT attached with an SMA to BNC adapter at the
+ feed point of a hand-held yagi used in conjunction with an Android
+ device running AltosDroid makes an outstanding ground station.
+ </para>
<para>
After the flight, you can use the radio link to extract the more detailed data
logged in either TeleMetrum or TeleMini devices, or you can use a mini USB cable to plug into the
of digital cameras and other modern electronic stuff will work fine.
</para>
<para>
- If your TeleMetrum-equipped rocket lands out of sight, you may enjoy having a hand-held GPS
- receiver, so that you can put in a way-point for the last reported rocket
- position before touch-down. This makes looking for your rocket a lot like
- Geo-Caching... just go to the way-point and look around starting from there.
+ If your rocket lands out of sight, you may enjoy having a hand-held
+ GPS receiver, so that you can put in a way-point for the last
+ reported rocket position before touch-down. This makes looking for
+ your rocket a lot like Geo-Caching... just go to the way-point and
+ look around starting from there. AltosDroid on an Android device
+ with GPS receiver works great for this, too!
</para>
<para>
- You may also enjoy having a ham radio "HT" that covers the 70cm band... you
+ You may also enjoy having a ham radio “HT” that covers the 70cm band... you
can use that with your antenna to direction-find the rocket on the ground
the same way you can use a Walston or Beeline tracker. This can be handy
if the rocket is hiding in sage brush or a tree, or if the last GPS position
doesn't get you close enough because the rocket dropped into a canyon, or
the wind is blowing it across a dry lake bed, or something like that... Keith
- and Bdale both currently own and use the Yaesu VX-7R at launches.
+ currently uses a Yaesu VX-7R, Bdale has a Baofung UV-5R
+ which isn't as nice, but was a whole lot cheaper.
</para>
<para>
So, to recap, on the ground the hardware you'll need includes:
<orderedlist inheritnum='inherit' numeration='arabic'>
<listitem>
- an antenna and feed-line
+ <para>
+ an antenna and feed-line or adapter
+ </para>
</listitem>
<listitem>
- a TeleDongle
+ <para>
+ a TeleDongle
+ </para>
</listitem>
<listitem>
- a notebook computer
+ <para>
+ a notebook computer
+ </para>
</listitem>
<listitem>
- optionally, a hand-held GPS receiver
+ <para>
+ optionally, a hand-held GPS receiver
+ </para>
</listitem>
<listitem>
- optionally, an HT or receiver covering 435 MHz
+ <para>
+ optionally, an HT or receiver covering 435 MHz
+ </para>
</listitem>
</orderedlist>
</para>
Arrow Antennas.
</ulink>
The 440-3 and 440-5 are both good choices for finding a
- TeleMetrum- or TeleMini- equipped rocket when used with a suitable 70cm HT.
+ TeleMetrum- or TeleMini- equipped rocket when used with a suitable
+ 70cm HT. TeleDongle and an SMA to BNC adapter fit perfectly
+ between the driven element and reflector of Arrow antennas.
</para>
</section>
<section>
</section>
<section>
<title>Future Plans</title>
+ <para>
+ We've designed a simple GPS based radio tracker called TeleGPS.
+ If all goes well, we hope to introduce this in the first
+ half of 2014.
+ </para>
<para>
- In the future, we intend to offer "companion boards" for the rocket that will
- plug in to TeleMetrum to collect additional data, provide more pyro channels,
- and so forth. A reference design for a companion board will be documented
- soon, and will be compatible with open source Arduino programming tools.
+ We have designed and prototyped several “companion boards” that
+ can attach to the companion connector on TeleMetrum and TeleMega
+ flight computers to collect more data, provide more pyro channels,
+ and so forth. We do not yet know if or when any of these boards
+ will be produced in enough quantity to sell. If you have specific
+ interests for data collection or control of events in your rockets
+ beyond the capabilities of our existing productions, please let
+ us know!
</para>
<para>
- We are also working on the design of a hand-held ground terminal that will
- allow monitoring the rocket's status, collecting data during flight, and
- logging data after flight without the need for a notebook computer on the
- flight line. Particularly since it is so difficult to read most notebook
- screens in direct sunlight, we think this will be a great thing to have.
+ Because all of our work is open, both the hardware designs and the
+ software, if you have some great idea for an addition to the current
+ Altus Metrum family, feel free to dive in and help! Or let us know
+ what you'd like to see that we aren't already working on, and maybe
+ we'll get excited about it too...
</para>
<para>
- Because all of our work is open, both the hardware designs and the software,
- if you have some great idea for an addition to the current Altus Metrum family,
- feel free to dive in and help! Or let us know what you'd like to see that
- we aren't already working on, and maybe we'll get excited about it too...
+ Watch our
+ <ulink url="http://altusmetrum.org/">web site</ulink> for more news
+ and information as our family of products evolves!
</para>
</section>
</chapter>
<para>
Building high-power rockets that fly safely is hard enough. Mix
in some sophisticated electronics and a bunch of radio energy
- and oftentimes you find few perfect solutions. This chapter
+ and some creativity and/or compromise may be required. This chapter
contains some suggestions about how to install Altus Metrum
- products into the rocket air-frame, including how to safely and
+ products into a rocket air-frame, including how to safely and
reliably mix a variety of electronics into the same air-frame.
</para>
<section>
<title>Mounting the Altimeter</title>
<para>
The first consideration is to ensure that the altimeter is
- securely fastened to the air-frame. For TeleMetrum, we use
- nylon standoffs and nylon screws; they're good to at least 50G
- and cannot cause any electrical issues on the board. For
- TeleMini, we usually cut small pieces of 1/16" balsa to fit
+ securely fastened to the air-frame. For most of our products, we
+ prefer nylon standoffs and nylon screws; they're good to at least 50G
+ and cannot cause any electrical issues on the board. Metal screws
+ and standoffs are fine, too, just be careful to avoid electrical
+ shorts! For TeleMini v1.0, we usually cut small pieces of 1/16 inch
+ balsa to fit
under the screw holes, and then take 2x56 nylon screws and
screw them through the TeleMini mounting holes, through the
balsa and into the underlying material.
</para>
<orderedlist inheritnum='inherit' numeration='arabic'>
<listitem>
- Make sure TeleMetrum is aligned precisely along the axis of
- acceleration so that the accelerometer can accurately
- capture data during the flight.
+ <para>
+ Make sure accelerometer-equipped products like TeleMetrum and
+ TeleMega are aligned precisely along the axis of
+ acceleration so that the accelerometer can accurately
+ capture data during the flight.
+ </para>
</listitem>
<listitem>
- Watch for any metal touching components on the
- board. Shorting out connections on the bottom of the board
- can cause the altimeter to fail during flight.
+ <para>
+ Watch for any metal touching components on the
+ board. Shorting out connections on the bottom of the board
+ can cause the altimeter to fail during flight.
+ </para>
</listitem>
</orderedlist>
</section>
culprit here -- CF is a good conductor and will effectively
shield the antenna, dramatically reducing signal strength and
range. Metallic flake paint is another effective shielding
- material which is to be avoided around any antennas.
+ material which should be avoided around any antennas.
</para>
<para>
If the ebay is large enough, it can be convenient to simply
consuming very little space.
</para>
<para>
- If you need to place the antenna at a distance from the
+ If you need to place the UHF antenna at a distance from the
altimeter, you can replace the antenna with an edge-mounted
SMA connector, and then run 50Ω coax from the board to the
antenna. Building a remote antenna is beyond the scope of this
<section>
<title>Preserving GPS Reception</title>
<para>
- The GPS antenna and receiver in TeleMetrum are highly
- sensitive and normally have no trouble tracking enough
+ The GPS antenna and receiver used in TeleMetrum and TeleMega is
+ highly sensitive and normally have no trouble tracking enough
satellites to provide accurate position information for
- recovering the rocket. However, there are many ways to
- attenuate the GPS signal.
+ recovering the rocket. However, there are many ways the GPS signal
+ can end up attenuated, negatively affecting GPS performance.
<orderedlist inheritnum='inherit' numeration='arabic'>
<listitem>
- Conductive tubing or coatings. Carbon fiber and metal
- tubing, or metallic paint will all dramatically attenuate the
- GPS signal. We've never heard of anyone successfully
- receiving GPS from inside these materials.
+ <para>
+ Conductive tubing or coatings. Carbon fiber and metal
+ tubing, or metallic paint will all dramatically attenuate the
+ GPS signal. We've never heard of anyone successfully
+ receiving GPS from inside these materials.
+ </para>
</listitem>
<listitem>
- Metal components near the GPS patch antenna. These will
- de-tune the patch antenna, changing the resonant frequency
- away from the L1 carrier and reduce the effectiveness of the
- antenna. You can place as much stuff as you like beneath the
- antenna as that's covered with a ground plane. But, keep
- wires and metal out from above the patch antenna.
+ <para>
+ Metal components near the GPS patch antenna. These will
+ de-tune the patch antenna, changing the resonant frequency
+ away from the L1 carrier and reduce the effectiveness of the
+ antenna. You can place as much stuff as you like beneath the
+ antenna as that's covered with a ground plane. But, keep
+ wires and metal out from above the patch antenna.
+ </para>
</listitem>
</orderedlist>
</para>
<para>
Any altimeter will generate RFI; the digital circuits use
high-frequency clocks that spray radio interference across a
- wide band. Altusmetrum altimeters generate intentional radio
+ wide band. Altus Metrum altimeters generate intentional radio
signals as well, increasing the amount of RF energy around the board.
</para>
<para>
<para>
Voltages are induced when radio frequency energy is
transmitted from one circuit to another. Here are things that
- increase the induced voltage and current:
+ influence the induced voltage and current:
</para>
<itemizedlist>
<listitem>
- Keep wires from different circuits apart. Moving circuits
- further apart will reduce RFI.
+ <para>
+ Keep wires from different circuits apart. Moving circuits
+ further apart will reduce RFI.
+ </para>
</listitem>
<listitem>
+ <para>
Avoid parallel wires from different circuits. The longer two
wires run parallel to one another, the larger the amount of
transferred energy. Cross wires at right angles to reduce
RFI.
+ </para>
</listitem>
<listitem>
+ <para>
Twist wires from the same circuits. Two wires the same
distance from the transmitter will get the same amount of
induced energy which will then cancel out. Any time you have
even out distances and reduce RFI. For altimeters, this
includes battery leads, switch hookups and igniter
circuits.
+ </para>
</listitem>
<listitem>
+ <para>
Avoid resonant lengths. Know what frequencies are present
in the environment and avoid having wire lengths near a
- natural resonant length. Altusmetrum products transmit on the
+ natural resonant length. Altus Metrum products transmit on the
70cm amateur band, so you should avoid lengths that are a
- simple ratio of that length; essentially any multiple of 1/4
+ simple ratio of that length; essentially any multiple of ¼
of the wavelength (17.5cm).
+ </para>
</listitem>
</itemizedlist>
</section>
To accurately measure atmospheric pressure, the ebay
containing the altimeter must be vented outside the
air-frame. The vent must be placed in a region of linear
- airflow, smooth and not in an area of increasing or decreasing
- pressure.
+ airflow, have smooth edges, and away from areas of increasing or
+ decreasing pressure.
</para>
<para>
- The barometric sensor in the altimeter is quite sensitive to
- chemical damage from the products of APCP or BP combustion, so
- make sure the ebay is carefully sealed from any compartment
- which contains ejection charges or motors.
+ All barometric sensors are quite sensitive to chemical damage from
+ the products of APCP or BP combustion, so make sure the ebay is
+ carefully sealed from any compartment which contains ejection
+ charges or motors.
</para>
</section>
<section>
mode. This will catch any mistakes in wiring and any residual
RFI issues that might accidentally fire igniters at the wrong
time. Let the air-frame sit for several minutes, checking for
- adequate telemetry signal strength and GPS lock.
+ adequate telemetry signal strength and GPS lock. If any igniters
+ fire unexpectedly, find and resolve the issue before loading any
+ BP charges!
</para>
<para>
Ground test the ejection charges. Prepare the rocket for
<chapter>
<title>Updating Device Firmware</title>
<para>
- The big conceptual thing to realize is that you have to use a
- TeleDongle as a programmer to update a TeleMetrum or TeleMini,
- and a TeleMetrum or other TeleDongle to program the TeleDongle
- Due to limited memory resources in the cc1111, we don't support
- programming directly over USB.
+ TeleMega, TeleMetrum v2 and EasyMini are all programmed directly
+ over their USB connectors (self programming). TeleMetrum v1, TeleMini and
+ TeleDongle are all programmed by using another device as a
+ programmer (pair programming). It's important to recognize which
+ kind of devices you have before trying to reprogram them.
</para>
<para>
You may wish to begin by ensuring you have current firmware images.
version from <ulink url="http://www.altusmetrum.org/AltOS/"/>.
</para>
<para>
- We recommend updating the altimeter first, before updating TeleDongle.
+ If you need to update the firmware on a TeleDongle, we recommend
+ updating the altimeter first, before updating TeleDongle. However,
+ note that TeleDongle rarely need to be updated. Any firmware version
+ 1.0.1 or later will work, version 1.2.1 may have improved receiver
+ performance slightly.
+ </para>
+ <para>
+ Self-programmable devices (TeleMega, TeleMetrum v2 and EasyMini)
+ are reprogrammed by connecting them to your computer over USB
</para>
<section>
- <title>Updating TeleMetrum Firmware</title>
+ <title>
+ Updating TeleMega, TeleMetrum v2 or EasyMini Firmware
+ </title>
+ <orderedlist inheritnum='inherit' numeration='arabic'>
+ <listitem>
+ <para>
+ Attach a battery and power switch to the target
+ device. Power up the device.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Using a Micro USB cable, connect the target device to your
+ computer's USB socket.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Run AltosUI, and select 'Flash Image' from the File menu.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Select the target device in the Device Selection dialog.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Select the image you want to flash to the device, which
+ should have a name in the form
+ <product>-v<product-version>-<software-version>.ihx, such
+ as TeleMega-v1.0-1.3.0.ihx.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Make sure the configuration parameters are reasonable
+ looking. If the serial number and/or RF configuration
+ values aren't right, you'll need to change them.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Hit the 'OK' button and the software should proceed to flash
+ the device with new firmware, showing a progress bar.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Verify that the device is working by using the 'Configure
+ Altimeter' item to check over the configuration.
+ </para>
+ </listitem>
+ </orderedlist>
+ <section>
+ <title>Recovering From Self-Flashing Failure</title>
+ <para>
+ If the firmware loading fails, it can leave the device
+ unable to boot. Not to worry, you can force the device to
+ start the boot loader instead, which will let you try to
+ flash the device again.
+ </para>
+ <para>
+ On each device, connecting two pins from one of the exposed
+ connectors will force the boot loader to start, even if the
+ regular operating system has been corrupted in some way.
+ </para>
+ <variablelist>
+ <varlistentry>
+ <term>TeleMega</term>
+ <listitem>
+ <para>
+ Connect pin 6 and pin 1 of the companion connector. Pin 1
+ can be identified by the square pad around it, and then
+ the pins could sequentially across the board. Be very
+ careful to <emphasis>not</emphasis> short pin 8 to
+ anything as that is connected directly to the battery. Pin
+ 7 carries 3.3V and the board will crash if that is
+ connected to pin 1, but shouldn't damage the board.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>TeleMetrum v2</term>
+ <listitem>
+ <para>
+ Connect pin 6 and pin 1 of the companion connector. Pin 1
+ can be identified by the square pad around it, and then
+ the pins could sequentially across the board. Be very
+ careful to <emphasis>not</emphasis> short pin 8 to
+ anything as that is connected directly to the battery. Pin
+ 7 carries 3.3V and the board will crash if that is
+ connected to pin 1, but shouldn't damage the board.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>EasyMini</term>
+ <listitem>
+ <para>
+ Connect pin 6 and pin 1 of the debug connector, which is
+ the six holes next to the beeper. Pin 1 can be identified
+ by the square pad around it, and then the pins could
+ sequentially across the board, making Pin 6 the one on the
+ other end of the row.
+ </para>
+ </listitem>
+ </varlistentry>
+ </variablelist>
+ </section>
+ </section>
+ <section>
+ <title>Pair Programming</title>
+ <para>
+ The big concept to understand is that you have to use a
+ TeleMega, TeleMetrum or TeleDongle as a programmer to update a
+ pair programmed device. Due to limited memory resources in the
+ cc1111, we don't support programming directly over USB for these
+ devices.
+ </para>
+ </section>
+ <section>
+ <title>Updating TeleMetrum v1.x Firmware</title>
<orderedlist inheritnum='inherit' numeration='arabic'>
<listitem>
+ <para>
Find the 'programming cable' that you got as part of the starter
kit, that has a red 8-pin MicroMaTch connector on one end and a
red 4-pin MicroMaTch connector on the other end.
+ </para>
</listitem>
<listitem>
+ <para>
Take the 2 screws out of the TeleDongle case to get access
to the circuit board.
+ </para>
</listitem>
<listitem>
+ <para>
Plug the 8-pin end of the programming cable to the
matching connector on the TeleDongle, and the 4-pin end to the
matching connector on the TeleMetrum.
Note that each MicroMaTch connector has an alignment pin that
goes through a hole in the PC board when you have the cable
oriented correctly.
+ </para>
</listitem>
<listitem>
+ <para>
Attach a battery to the TeleMetrum board.
+ </para>
</listitem>
<listitem>
+ <para>
Plug the TeleDongle into your computer's USB port, and power
up the TeleMetrum.
+ </para>
</listitem>
<listitem>
+ <para>
Run AltosUI, and select 'Flash Image' from the File menu.
+ </para>
</listitem>
<listitem>
+ <para>
Pick the TeleDongle device from the list, identifying it as the
programming device.
+ </para>
</listitem>
<listitem>
+ <para>
Select the image you want put on the TeleMetrum, which should have a
- name in the form telemetrum-v1.1-1.0.0.ihx. It should be visible
+ name in the form telemetrum-v1.2-1.0.0.ihx. It should be visible
in the default directory, if not you may have to poke around
your system to find it.
+ </para>
</listitem>
<listitem>
+ <para>
Make sure the configuration parameters are reasonable
looking. If the serial number and/or RF configuration
values aren't right, you'll need to change them.
+ </para>
</listitem>
<listitem>
+ <para>
Hit the 'OK' button and the software should proceed to flash
the TeleMetrum with new firmware, showing a progress bar.
+ </para>
</listitem>
<listitem>
+ <para>
Confirm that the TeleMetrum board seems to have updated OK, which you
can do by plugging in to it over USB and using a terminal program
to connect to the board and issue the 'v' command to check
the version, etc.
+ </para>
</listitem>
<listitem>
+ <para>
If something goes wrong, give it another try.
+ </para>
</listitem>
</orderedlist>
</section>
<title>Updating TeleMini Firmware</title>
<orderedlist inheritnum='inherit' numeration='arabic'>
<listitem>
+<para>
You'll need a special 'programming cable' to reprogram the
- TeleMini. It's available on the Altus Metrum web store, or
- you can make your own using an 8-pin MicroMaTch connector on
- one end and a set of four pins on the other.
- </listitem>
+ TeleMini. You can make your own using an 8-pin MicroMaTch
+ connector on one end and a set of four pins on the other.
+ </para>
+</listitem>
<listitem>
+<para>
Take the 2 screws out of the TeleDongle case to get access
to the circuit board.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Plug the 8-pin end of the programming cable to the matching
connector on the TeleDongle, and the 4-pins into the holes
in the TeleMini circuit board. Note that the MicroMaTch
the PC board when you have the cable oriented correctly, and
that pin 1 on the TeleMini board is marked with a square pad
while the other pins have round pads.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Attach a battery to the TeleMini board.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Plug the TeleDongle into your computer's USB port, and power
up the TeleMini
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Run AltosUI, and select 'Flash Image' from the File menu.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Pick the TeleDongle device from the list, identifying it as the
programming device.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Select the image you want put on the TeleMini, which should have a
name in the form telemini-v1.0-1.0.0.ihx. It should be visible
in the default directory, if not you may have to poke around
your system to find it.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Make sure the configuration parameters are reasonable
looking. If the serial number and/or RF configuration
values aren't right, you'll need to change them.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Hit the 'OK' button and the software should proceed to flash
the TeleMini with new firmware, showing a progress bar.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Confirm that the TeleMini board seems to have updated OK, which you
can do by configuring it over the radio link through the TeleDongle, or
- letting it come up in "flight" mode and listening for telemetry.
- </listitem>
+ letting it come up in “flight” mode and listening for telemetry.
+ </para>
+</listitem>
<listitem>
+<para>
If something goes wrong, give it another try.
- </listitem>
+ </para>
+</listitem>
</orderedlist>
</section>
<section>
</para>
<orderedlist inheritnum='inherit' numeration='arabic'>
<listitem>
+<para>
Find the 'programming cable' that you got as part of the starter
kit, that has a red 8-pin MicroMaTch connector on one end and a
red 4-pin MicroMaTch connector on the other end.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Find the USB cable that you got as part of the starter kit, and
- plug the "mini" end in to the mating connector on TeleMetrum or TeleDongle.
- </listitem>
+ plug the “mini” end in to the mating connector on TeleMetrum or TeleDongle.
+ </para>
+</listitem>
<listitem>
+<para>
Take the 2 screws out of the TeleDongle case to get access
to the circuit board.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Plug the 8-pin end of the programming cable to the
matching connector on the programmer, and the 4-pin end to the
matching connector on the TeleDongle.
Note that each MicroMaTch connector has an alignment pin that
goes through a hole in the PC board when you have the cable
oriented correctly.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Attach a battery to the TeleMetrum board if you're using one.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Plug both the programmer and the TeleDongle into your computer's USB
ports, and power up the programmer.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Run AltosUI, and select 'Flash Image' from the File menu.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Pick the programmer device from the list, identifying it as the
programming device.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Select the image you want put on the TeleDongle, which should have a
name in the form teledongle-v0.2-1.0.0.ihx. It should be visible
in the default directory, if not you may have to poke around
your system to find it.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Make sure the configuration parameters are reasonable
looking. If the serial number and/or RF configuration
values aren't right, you'll need to change them. The TeleDongle
- serial number is on the "bottom" of the circuit board, and can
+ serial number is on the “bottom” of the circuit board, and can
usually be read through the translucent blue plastic case without
needing to remove the board from the case.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Hit the 'OK' button and the software should proceed to flash
the TeleDongle with new firmware, showing a progress bar.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Confirm that the TeleDongle board seems to have updated OK, which you
can do by plugging in to it over USB and using a terminal program
to connect to the board and issue the 'v' command to check
the version, etc. Once you're happy, remove the programming cable
and put the cover back on the TeleDongle.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
If something goes wrong, give it another try.
- </listitem>
+ </para>
+</listitem>
</orderedlist>
<para>
Be careful removing the programming cable from the locking 8-pin
used in a rocket don't ever come loose accidentally in flight.
</para>
</section>
- </chapter>
- <chapter>
- <title>Hardware Specifications</title>
+ </chapter>
+ <chapter>
+ <title>Hardware Specifications</title>
+ <section>
+ <title>
+ TeleMega Specifications
+ </title>
+ <itemizedlist>
+ <listitem>
+ <para>
+ Recording altimeter for model rocketry.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Supports dual deployment and four auxiliary pyro channels
+ (a total of 6 events).
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ 70cm 40mW ham-band transceiver for telemetry down-link.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Barometric pressure sensor good to 100k feet MSL.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ 1-axis high-g accelerometer for motor characterization, capable of
+ +/- 102g.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ 9-axis IMU including integrated 3-axis accelerometer,
+ 3-axis gyroscope and 3-axis magnetometer.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ On-board, integrated uBlox Max 7 GPS receiver with 5Hz update rate capability.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ On-board 8 Megabyte non-volatile memory for flight data storage.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ USB interface for battery charging, configuration, and data recovery.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Fully integrated support for Li-Po rechargeable batteries.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Can use either main system Li-Po or optional separate pyro battery
+ to fire e-matches.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ 3.25 x 1.25 inch board designed to fit inside 38mm air-frame coupler tube.
+ </para>
+ </listitem>
+ </itemizedlist>
+ </section>
+ <section>
+ <title>
+ TeleMetrum v2 Specifications
+ </title>
+ <itemizedlist>
+ <listitem>
+ <para>
+ Recording altimeter for model rocketry.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Supports dual deployment (can fire 2 ejection charges).
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ 70cm, 40mW ham-band transceiver for telemetry down-link.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Barometric pressure sensor good to 100k feet MSL.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ 1-axis high-g accelerometer for motor characterization, capable of
+ +/- 102g.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ On-board, integrated uBlox Max 7 GPS receiver with 5Hz update rate capability.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ On-board 8 Megabyte non-volatile memory for flight data storage.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ USB interface for battery charging, configuration, and data recovery.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Fully integrated support for Li-Po rechargeable batteries.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Uses Li-Po to fire e-matches, can be modified to support
+ optional separate pyro battery if needed.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ 2.75 x 1 inch board designed to fit inside 29mm air-frame coupler tube.
+ </para>
+ </listitem>
+ </itemizedlist>
+ </section>
<section>
- <title>TeleMetrum Specifications</title>
+ <title>TeleMetrum v1 Specifications</title>
<itemizedlist>
<listitem>
<para>
</listitem>
<listitem>
<para>
- 70cm ham-band transceiver for telemetry down-link.
+ 70cm, 10mW ham-band transceiver for telemetry down-link.
</para>
</listitem>
<listitem>
</itemizedlist>
</section>
<section>
- <title>TeleMini Specifications</title>
+ <title>
+ TeleMini v2.0 Specifications
+ </title>
+ <itemizedlist>
+ <listitem>
+ <para>
+ Recording altimeter for model rocketry.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Supports dual deployment (can fire 2 ejection charges).
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ 70cm, 10mW ham-band transceiver for telemetry down-link.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Barometric pressure sensor good to 100k feet MSL.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ On-board 1 megabyte non-volatile memory for flight data storage.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ USB interface for configuration, and data recovery.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Support for Li-Po rechargeable batteries (using an
+ external charger), or any 3.7-15V external battery.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Uses Li-Po to fire e-matches, can be modified to support
+ optional separate pyro battery if needed.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ 1.5 x .8 inch board designed to fit inside 24mm air-frame coupler tube.
+ </para>
+ </listitem>
+ </itemizedlist>
+ </section>
+ <section>
+ <title>
+ TeleMini v1.0 Specifications
+ </title>
<itemizedlist>
<listitem>
<para>
</listitem>
<listitem>
<para>
- 70cm ham-band transceiver for telemetry down-link.
+ 70cm, 10mW ham-band transceiver for telemetry down-link.
</para>
</listitem>
<listitem>
</listitem>
<listitem>
<para>
- RF interface for battery charging, configuration, and data recovery.
+ RF interface for configuration, and data recovery.
</para>
</listitem>
<listitem>
</listitem>
</itemizedlist>
</section>
+ <section>
+ <title>
+ EasyMini Specifications
+ </title>
+ <itemizedlist>
+ <listitem>
+ <para>
+ Recording altimeter for model rocketry.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Supports dual deployment (can fire 2 ejection charges).
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Barometric pressure sensor good to 100k feet MSL.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ On-board 1 megabyte non-volatile memory for flight data storage.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ USB interface for configuration, and data recovery.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Support for Li-Po rechargeable batteries (using an
+ external charger), or any 3.7-15V external battery.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Uses Li-Po to fire e-matches, can be modified to support
+ optional separate pyro battery if needed.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ 1.5 x .8 inch board designed to fit inside 24mm air-frame coupler tube.
+ </para>
+ </listitem>
+ </itemizedlist>
+ </section>
</chapter>
<chapter>
<title>FAQ</title>
<para>
- TeleMetrum seems to shut off when disconnected from the
- computer. Make sure the battery is adequately charged. Remember the
+ <emphasis>TeleMetrum seems to shut off when disconnected from the
+ computer.</emphasis> <?linebreak?>
+ Make sure the battery is adequately charged. Remember the
unit will pull more power than the USB port can deliver before the
- GPS enters "locked" mode. The battery charges best when TeleMetrum
+ GPS enters “locked” mode. The battery charges best when TeleMetrum
is turned off.
</para>
<para>
- It's impossible to stop the TeleDongle when it's in "p" mode, I have
- to unplug the USB cable? Make sure you have tried to "escape out" of
+ <emphasis>It's impossible to stop the TeleDongle when it's in “p” mode, I have
+ to unplug the USB cable? </emphasis><?linebreak?>
+ Make sure you have tried to “escape out” of
this mode. If this doesn't work the reboot procedure for the
TeleDongle *is* to simply unplug it. 'cu' however will retain it's
- outgoing buffer IF your "escape out" ('~~') does not work.
+ outgoing buffer IF your “escape out” ('~~') does not work.
At this point using either 'ao-view' (or possibly
'cutemon') instead of 'cu' will 'clear' the issue and allow renewed
communication.
</para>
<para>
- The amber LED (on the TeleMetrum) lights up when both
- battery and USB are connected. Does this mean it's charging?
+ <emphasis>The amber LED (on the TeleMetrum) lights up when both
+ battery and USB are connected. Does this mean it's charging?
+ </emphasis><?linebreak?>
Yes, the yellow LED indicates the charging at the 'regular' rate.
If the led is out but the unit is still plugged into a USB port,
then the battery is being charged at a 'trickle' rate.
</para>
<para>
- There are no "dit-dah-dah-dit" sound or lights like the manual mentions?
- That's the "pad" mode. Weak batteries might be the problem.
- It is also possible that the TeleMetrum is horizontal and the output
- is instead a "dit-dit" meaning 'idle'. For TeleMini, it's possible that
- it received a command packet which would have left it in "pad" mode.
+ <emphasis>There are no “dit-dah-dah-dit” sound or lights like the manual
+ mentions?</emphasis><?linebreak?>
+ That's the “pad” mode. Weak batteries might be the problem.
+ It is also possible that the flight computer is horizontal and the
+ output
+ is instead a “dit-dit” meaning 'idle'. For TeleMini, it's possible that
+ it received a command packet which would have left it in “pad” mode.
</para>
<para>
- How do I save flight data?
+ <emphasis>How do I save flight data?</emphasis><?linebreak?>
Live telemetry is written to file(s) whenever AltosUI is connected
to the TeleDongle. The file area defaults to ~/TeleMetrum
but is easily changed using the menus in AltosUI. The files that
Verify you can connect and disconnect from the units while in your
terminal program by sending the escape-disconnect mentioned above.
</para>
+ <para>
+ To set the radio frequency, use the 'c R' command to specify the
+ radio transceiver configuration parameter. This parameter is computed
+ using the desired frequency, 'F', the radio calibration parameter, 'C' (showed by the 'c s' command) and
+ the standard calibration reference frequency, 'S', (normally 434.550MHz):
+ <programlisting>
+ R = F / S * C
+ </programlisting>
+ Round the result to the nearest integer value.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board flash on
+ your altimeter board if you want the change to stay in place across reboots.
+ </para>
+ <para>
+ To set the apogee delay, use the 'c d' command.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board DataFlash chip.
+ </para>
+ <para>
+ To set the main deployment altitude, use the 'c m' command.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board DataFlash chip.
+ </para>
+ <para>
+ To calibrate the radio frequency, connect the UHF antenna port to a
+ frequency counter, set the board to 434.550MHz, and use the 'C'
+ command to generate a CW carrier. Wait for the transmitter temperature
+ to stabilize and the frequency to settle down.
+ Then, divide 434.550 MHz by the
+ measured frequency and multiply by the current radio cal value show
+ in the 'c s' command. For an unprogrammed board, the default value
+ is 1186611 for cc1111 based products and 7119667 for cc1120
+ based products. Take the resulting integer and program it using the 'c f'
+ command. Testing with the 'C' command again should show a carrier
+ within a few tens of Hertz of the intended frequency.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the configuration memory.
+ </para>
<para>
Note that the 'reboot' command, which is very useful on the altimeters,
will likely just cause problems with the dongle. The *correct* way
</para>
<para>
Now might be a good time to take a break and read the rest of this
- manual, particularly about the two "modes" that the altimeters
+ manual, particularly about the two “modes” that the altimeters
can be placed in. TeleMetrum uses the position of the device when booting
- up will determine whether the unit is in "pad" or "idle" mode. TeleMini
- enters "idle" mode when it receives a command packet within the first 5 seconds
- of being powered up, otherwise it enters "pad" mode.
+ up will determine whether the unit is in “pad” or “idle” mode. TeleMini
+ enters “idle” mode when it receives a command packet within the first 5 seconds
+ of being powered up, otherwise it enters “pad” mode.
</para>
<para>
You can access an altimeter in idle mode from the TeleDongle's USB
connection using the radio link
by issuing a 'p' command to the TeleDongle. Practice connecting and
disconnecting ('~~' while using 'cu') from the altimeter. If
- you cannot escape out of the "p" command, (by using a '~~' when in
+ you cannot escape out of the “p” command, (by using a '~~' when in
CU) then it is likely that your kernel has issues. Try a newer version.
</para>
<para>
is in 'idle mode' and then place the
rocket vertically on the launch pad, walk away and then issue a
reboot command. The altimeter will reboot and start sending data
- having changed to the "pad" mode. If the TeleDongle is not receiving
+ having changed to the “pad” mode. If the TeleDongle is not receiving
this data, you can disconnect 'cu' from the TeleDongle using the
procedures mentioned above and THEN connect to the TeleDongle from
inside 'ao-view'. If this doesn't work, disconnect from the
strength providing an indication of the direction from receiver to rocket.
</para>
<para>
- TeleMetrum also provides GPS trekking data, which can further simplify
+ TeleMetrum also provides GPS tracking data, which can further simplify
locating the rocket once it has landed. (The last good GPS data
received before touch-down will be on the data screen of 'ao-view'.)
</para>
once you enable the voice output!
</para>
</appendix>
- <appendix
- xmlns:xi="http://www.w3.org/2001/XInclude">
+ <appendix>
+ <title>Drill Templates</title>
+ <para>
+ These images, when printed, provide precise templates for the
+ mounting holes in Altus Metrum flight computers
+ </para>
+ <section>
+ <title>TeleMega template</title>
+ <para>
+ TeleMega has overall dimensions of 1.250 x 3.250 inches, and
+ the mounting holes are sized for use with 4-40 or M3 screws.
+ </para>
+ <informalfigure>
+ <mediaobject id="TeleMegaTemplate">
+ <imageobject>
+ <imagedata format="SVG" fileref="telemega.svg"
+ scalefit="0" scale="100" align="center" />
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ </section>
+ <section>
+ <title>TeleMetrum template</title>
+ <para>
+ TeleMetrum has overall dimensions of 1.000 x 2.750 inches, and the
+ mounting holes are sized for use with 4-40 or M3 screws.
+ </para>
+ <informalfigure>
+ <mediaobject id="TeleMetrumTemplate">
+ <imageobject>
+ <imagedata format="SVG" fileref="telemetrum.svg"
+ scalefit="0" scale="100" align="center" />
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ </section>
+ <section>
+ <title>TeleMini v2/EasyMini template</title>
+ <para>
+ TeleMini v2 and EasyMini have overall dimensions of 0.800 x 1.500 inches, and the
+ mounting holes are sized for use with 4-40 or M3 screws.
+ </para>
+ <informalfigure>
+ <mediaobject id="MiniTemplate">
+ <imageobject>
+ <imagedata format="SVG" fileref="easymini.svg"
+ scalefit="0" scale="100" align="center" />
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ </section>
+ <section>
+ <title>TeleMini v1 template</title>
+ <para>
+ TeleMini has overall dimensions of 0.500 x 1.500 inches, and the
+ mounting holes are sized for use with 2-56 or M2 screws.
+ </para>
+ <informalfigure>
+ <mediaobject id="TeleMiniTemplate">
+ <imageobject>
+ <imagedata format="SVG" fileref="telemini.svg"
+ scalefit="0" scale="100" align="center" />
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ </section>
+ </appendix>
+ <appendix>
+ <title>Calibration</title>
+ <para>
+ There are only two calibrations required for TeleMetrum and
+ TeleMega, and only one for TeleDongle, TeleMini and EasyMini.
+ All boards are shipped from the factory pre-calibrated, but
+ the procedures are documented here in case they are ever
+ needed. Re-calibration is not supported by AltosUI, you must
+ connect to the board with a serial terminal program and
+ interact directly with the on-board command interpreter to
+ effect calibration.
+ </para>
+ <section>
+ <title>Radio Frequency</title>
+ <para>
+ The radio frequency is synthesized from a clock based on the
+ crystal on the board. The actual frequency of this oscillator
+ must be measured to generate a calibration constant. While our
+ GFSK modulation
+ bandwidth is wide enough to allow boards to communicate even when
+ their oscillators are not on exactly the same frequency, performance
+ is best when they are closely matched.
+ Radio frequency calibration requires a calibrated frequency counter.
+ Fortunately, once set, the variation in frequency due to aging and
+ temperature changes is small enough that re-calibration by customers
+ should generally not be required.
+ </para>
+ <para>
+ To calibrate the radio frequency, connect the UHF antenna
+ port to a frequency counter, set the board to 434.550MHz,
+ and use the 'C' command in the on-board command interpreter
+ to generate a CW carrier. For USB-enabled boards, this is
+ best done over USB. For TeleMini v1, note that the only way
+ to escape the 'C' command is via power cycle since the board
+ will no longer be listening for commands once it starts
+ generating a CW carrier.
+ </para>
+ <para>
+ Wait for the transmitter temperature to stabilize and the frequency
+ to settle down. Then, divide 434.550 MHz by the
+ measured frequency and multiply by the current radio cal value show
+ in the 'c s' command. For an unprogrammed board, the default value
+ is 1186611. Take the resulting integer and program it using the 'c f'
+ command. Testing with the 'C' command again should show a carrier
+ within a few tens of Hertz of the intended frequency.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board storage chip.
+ </para>
+ <para>
+ Note that any time you re-do the radio frequency calibration, the
+ radio frequency is reset to the default 434.550 Mhz. If you want
+ to use another frequency, you will have to set that again after
+ calibration is completed.
+ </para>
+ </section>
+ <section>
+ <title>TeleMetrum and TeleMega Accelerometers</title>
+ <para>
+ While barometric sensors are factory-calibrated,
+ accelerometers are not, and so each must be calibrated once
+ installed in a flight computer. Explicitly calibrating the
+ accelerometers also allows us to load any compatible device.
+ We perform a two-point calibration using gravity.
+ </para>
+ <para>
+ To calibrate the acceleration sensor, use the 'c a 0' command. You
+ will be prompted to orient the board vertically with the UHF antenna
+ up and press a key, then to orient the board vertically with the
+ UHF antenna down and press a key. Note that the accuracy of this
+ calibration depends primarily on how perfectly vertical and still
+ the board is held during the cal process. As with all 'c'
+ sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board DataFlash chip.
+ </para>
+ <para>
+ The +1g and -1g calibration points are included in each telemetry
+ frame and are part of the header stored in onboard flash to be
+ downloaded after flight. We always store and return raw ADC
+ samples for each sensor... so nothing is permanently “lost” or
+ “damaged” if the calibration is poor.
+ </para>
+ <para>
+ In the unlikely event an accel cal goes badly, it is possible
+ that TeleMetrum or TeleMega may always come up in 'pad mode'
+ and as such not be listening to either the USB or radio link.
+ If that happens, there is a special hook in the firmware to
+ force the board back in to 'idle mode' so you can re-do the
+ cal. To use this hook, you just need to ground the SPI clock
+ pin at power-on. This pin is available as pin 2 on the 8-pin
+ companion connector, and pin 1 is ground. So either
+ carefully install a fine-gauge wire jumper between the two
+ pins closest to the index hole end of the 8-pin connector, or
+ plug in the programming cable to the 8-pin connector and use
+ a small screwdriver or similar to short the two pins closest
+ to the index post on the 4-pin end of the programming cable,
+ and power up the board. It should come up in 'idle mode'
+ (two beeps), allowing a re-cal.
+ </para>
+ </section>
+ </appendix>
+ <appendix>
<title>Release Notes</title>
- <xi:include href="release-notes-1.0.xsl" xpointer="xpointer(/article/*)"/>
- <xi:include href="release-notes-0.9.2.xsl" xpointer="xpointer(/article/*)"/>
- <xi:include href="release-notes-0.9.xsl" xpointer="xpointer(/article/*)"/>
- <xi:include href="release-notes-0.8.xsl" xpointer="xpointer(/article/*)"/>
- <xi:include href="release-notes-0.7.1.xsl" xpointer="xpointer(/article/*)"/>
+ <simplesect>
+ <title>Version 1.41</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.4.1.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.4</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.4.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.3.2</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.3.2.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.3.1</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.3.1.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.3</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.3.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.2.1</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.2.1.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.2</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.2.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.1.1</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.1.1.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.1</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.1.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.0.1</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.0.1.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 0.9.2</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-0.9.2.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 0.9</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-0.9.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 0.8</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-0.8.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 0.7.1</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-0.7.1.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
</appendix>
</book>
-<!-- LocalWords: Altusmetrum
+<!-- LocalWords: Altusmetrum
-->