Keith Packard [Wed, 13 Jun 2012 15:24:26 +0000 (08:24 -0700)]
Add 22-ohm resistors to USB data lines
Probably a good idea.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 9 Jun 2012 10:38:14 +0000 (03:38 -0700)]
Move ink for serial number down under the license.
Seems like a more reasonable spot.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 9 Jun 2012 10:35:04 +0000 (03:35 -0700)]
Use all through-hole LEDs. Add mounting holes.
Replace SMT LEDs with larger through-hole versions so they will be
visible through the panel.
Add 8 mounting holes.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 9 Jun 2012 08:35:56 +0000 (01:35 -0700)]
Nearly route complete with LCD and knobs on backside of board.
Just need to mess with LEDs now
Keith Packard [Sat, 9 Jun 2012 01:57:07 +0000 (18:57 -0700)]
Add footprint for USB bare wires
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 9 Jun 2012 01:51:53 +0000 (18:51 -0700)]
Replace PEC11L rotary switch with PEC11 version
This one is available in the desired style
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 9 Jun 2012 01:47:59 +0000 (18:47 -0700)]
Update with battery charger, new STM debug etc
This just gets the parts in the schematic and pcb file, no layout or
routing done yet.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 9 Jun 2012 01:43:06 +0000 (18:43 -0700)]
Move LCD and switches to back side of board
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 8 Jun 2012 22:53:19 +0000 (15:53 -0700)]
Switch from PEC11L to PEC11 for rotary switch
The PEC11 is available from mouser in the desired configuration;
no-one appears to stock the PEC11L in a similar configuration.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 7 Jun 2012 09:08:45 +0000 (02:08 -0700)]
Shrink PCB to 4.5" x 4.5"
Same size as telepad.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 7 Jun 2012 07:53:42 +0000 (00:53 -0700)]
Create PCB layout
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 7 Jun 2012 01:20:28 +0000 (18:20 -0700)]
Add packages and set footprints
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 7 Jun 2012 00:09:58 +0000 (17:09 -0700)]
Start telelco work.
Includes STM32L processor and CC1111 for radio.
Signed-off-by: Keith Packard <keithp@keithp.com>