# Purpose - Create some $BIT variables
# Create $K and $M variables
# and some bit field extraction variables.
-# Creat helper variables ...
+# Create helper variables ...
# BIT0.. BIT31
for { set x 0 } { $x < 32 } { set x [expr {$x + 1}]} {
#
# FIXME:
# Add (A) sdram configuration
-# Add (B) flash cfi programing configuration
+# Add (B) flash cfi programming configuration
#
nand probe nandflash_cs3
- # The AT91SAM9G20-EK evaluation board has build-in serial data flash also.
+ # The AT91SAM9G20-EK evaluation board has built-in serial data flash also.
# Now setup SDRAM. This is tricky and configuration is very important for reliability! The current calculations
# are based on 2 x Micron MT48LC16M16A2-75 memory (4 M x 16 bit x 4 banks). If you use this file as a reference
# ID 1443:0007 Digilent Development board JTAG
#
# However, the ixo-usb-jtag project provides an alternative open firmware for
-# the on board programmer. When using thie firmware the board will then
+# the on board programmer. When using this firmware the board will then
# enumerate as:
# ID 16c0:06ad Van Ooijen Technische Informatica
# (With SerialNumber == hw_nexys)
$_TARGETNAME configure -event reset-init {
# Flash
- mww 0x20200010 0x00000007 ;# FBWST: 7 wait states, not chached
+ mww 0x20200010 0x00000007 ;# FBWST: 7 wait states, not cached
# Use PLL
mww 0xFFFF8020 0x00000001 ;# XTAL_OSC_CONTROL: enable, 1-20 MHz
# it's apt-get install libusb-dev. When I made my config I only included
# --enable-jlink and --enable-usbdevs
#
-# I HAVE NOT Tested this throughly, so there could still be problems.
+# I HAVE NOT Tested this thoroughly, so there could still be problems.
# But it should get you way ahead of the game from where I started.
# If you find problems (and fixes) please post them to
# openocd-development@lists.berlios.de and join the developers and
# Target Configuration for the Uptech 2410 board.
-# This configuration hould also work on smdk2410, but I havn't tested it yet.
+# This configuration should also work on smdk2410, but I haven't tested it yet.
# Author: xionglingfeng@Gmail.com
source [find target/samsung_s3c2410.cfg]
#
# You also need to have reliable GND connection between the target and
# adapter. Vref of the adapter should be supplied with a voltage equal
-# to the target's (preferrably connect it to Vcc). You can also
+# to the target's (preferably connect it to Vcc). You can also
# optionally connect nSRST. Leave everything else unconnected.
#
# FTDI Target
# setup GPIO used as control signals for C100
setupGPIO
- # This will allow acces to lower 8MB or NOR
+ # This will allow access to lower 8MB or NOR
lowGPIO5
# setup NOR size,timing,etc.
setupNOR
#mww $EX_CS0_TMG3_REG
# set EBUS clock 165/5=33MHz
mww $EX_CLOCK_DIV_REG 0x5
- # everthing else is OK with default
+ # everything else is OK with default
}
proc bootNOR {} {
proc ooma_board_detect {} {
set GPIO_BOOTSTRAP_REG [regs GPIO_BOOTSTRAP_REG]
- # read the current value of the BOOTSRAP pins
+ # read the current value of the BOOTSTRAP pins
set tmp [mrw $GPIO_BOOTSTRAP_REG]
echo [format "GPIO_BOOTSTRAP_REG (0x%x): 0x%x" $GPIO_BOOTSTRAP_REG $tmp]
# extract the GPBP bits
echo "10) showArmClk: will show current config registers for Arm Bus Clock"
echo "11) setupArmClk: will setup Amba Bus Clock=450MHz"
echo "12) ooma_board_detect: will show which version of Telo you have"
- echo "13) setupDDR2: will configure DDR2 controller, you must have PLLs configureg"
+ echo "13) setupDDR2: will configure DDR2 controller, you must have PLLs configured"
echo "14) showDDR2: will show DDR2 config registers"
echo "15) showWatchdog: will show current register config for watchdog"
echo "16) reboot: will trigger watchdog and reboot Telo (hw reset)"
echo "17) bootNOR: will boot Telo from NOR"
- echo "18) setupUART0: will configure UART0 for 115200 8N1, PLLs have to be confiured"
+ echo "18) setupUART0: will configure UART0 for 115200 8N1, PLLs have to be configured"
echo "19) putcUART0: will print a character on UART0"
echo "20) putsUART0: will print a string on UART0"
- echo "21) trainDDR2: will run DDR2 training program"
- echo "22) flashUBOOT: will prgram NOR sectors 0-3 with u-boot.bin"
+ echo "21) trainDDR2: will run DDR2 training program"
+ echo "22) flashUBOOT: will program NOR sectors 0-3 with u-boot.bin"
}
source [find mem_helper.tcl]
if {$aln != 0} {
# clear pllcmd.GO
mww [expr {$pll_addr + 0x0138}] 0x00
- # write alingment flags
+ # write alignment flags
mww [expr {$pll_addr + 0x0140}] $aln
# write pllcmd.GO; poll pllstat.GO
mww [expr {$pll_addr + 0x0138}] 0x01
echo "Notice: sysclock set to 500kHz."
}
-# Do not remap the ARM interrupt vectors to anything but the beginning ot the flash.
+# Do not remap the ARM interrupt vectors to anything but the beginning of the flash.
# Table System memory remap register (SYSMEMREMAP, address 0x4004 8000) bit description
# Bit Symbol Value Description
# 0 map - interrupt vector remap. 0 after boot.
#
# Newer families like PSoC 4000, 4100M, 4200M, 4100L, 4200L and PSoC 4 BLE
# clear TEST_MODE flag during device reset so workaround is not possible.
-# Use a KitProg adapter for theese devices or "reset halt" will not stop
+# Use a KitProg adapter for these devices or "reset halt" will not stop
# before executing user code.
#
# 3) SWD cannot be connected during system initialization after reset.
projects / fw / openocd / commitdiff