doc: Mention BMX-160 self-test fix in 1.9.6 release notes

[fw/altos] / doc / updating-firmware.inc

diff --git a/doc/updating-firmware.inc b/doc/updating-firmware.inc
index 98e04cea6a8220b450f01e8a9235edad654134f8..b9216a2235288d58a8c50705d18b40a6b9b2101c 100644 (file)
--- a/doc/updating-firmware.inc
+++ b/doc/updating-firmware.inc
@@ -2,7 +2,7 @@
 == Updating Device Firmware
 
        ifdef::telemega[]
-       TeleMega, TeleMetrum v2, EasyMega, EasyMini and TeleDongle v3
+       TeleMega, TeleMetrum v2 and newer, EasyMega, EasyMini and TeleDongle v3
        are all
        endif::telemega[]
        ifndef::telemega[]
@@ -28,7 +28,7 @@
 
        ifdef::telemega[]
 
-       === Updating TeleMega, TeleMetrum v2, EasyMega, EasyMini or TeleDongle v3 Firmware
+       === Updating TeleMega, TeleMetrum v2 or newer, EasyMega, EasyMini, TeleDongle v3 or TeleBT v3 Firmware
 
        endif::telemega[]
        ifndef::telemega[]
@@ -84,7 +84,7 @@
 
                        Connect pin 6 and pin 1 of the companion
                        connector. Pin 1 can be identified by the square pad
-                       around it, and then the pins could sequentially across
+                       around it, and then the pins count sequentially across
                        the board. Be very careful to *not* short pin 8 to
                        anything as that is connected directly to the
                        battery. Pin 7 carries 3.3V and the board will crash
@@ -97,7 +97,7 @@
 
                        Connect pin 6 and pin 1 of the companion
                        connector. Pin 1 can be identified by the square pad
-                       around it, and then the pins could sequentially across
+                       around it, and then the pins count sequentially across
                        the board. Be very careful to *not* short pin 8 to
                        anything as that is connected directly to the
                        battery. Pin 7 carries 3.3V and the board will crash
@@ -105,12 +105,22 @@
                        the board.
                        endif::easymega[]
 
+                       ifdef::easytimer[]
+                       EasyTimer::
+
+                       Connect pin 5 and pin 1 of the debug connector, which
+                       is the six holes next to the beeper. Pin 1 can be
+                       identified by the square pad around it, and then the
+                       pins count sequentially across the board, making Pin 5
+                       the one on the other end of the row.
+                       endif::easytimer[]
+
                        ifdef::telemetrum[]
-                       TeleMetrum v2::
+                       TeleMetrum v2 and newer::
 
                        Connect pin 6 and pin 1 of the companion
                        connector. Pin 1 can be identified by the square pad
-                       around it, and then the pins could sequentially across
+                       around it, and then the pins count sequentially across
                        the board. Be very careful to *not* short pin 8 to
                        anything as that is connected directly to the
                        battery. Pin 7 carries 3.3V and the board will crash
@@ -124,10 +134,22 @@
                        Connect pin 6 and pin 1 of the debug connector, which
                        is the six holes next to the beeper. Pin 1 can be
                        identified by the square pad around it, and then the
-                       pins could sequentially across the board, making Pin 6
+                       pins count sequentially across the board, making Pin 6
                        the one on the other end of the row.
                        endif::easymini[]
 
+                       TeleGPS v1::
+
+                       Connect pin 32 on the CPU to ground.  Pin 32 is the
+                       right-most pin on the bottom edge of the CPU when the
+                       board is oriented with the USB and battery connectors
+                       to the right.
+
+                       TeleGPS v2::
+
+                       Connect together pins 1 and 5 of the Debug connector.
+                       Pin 1 is the pin with the square pad around the hole.
+
                        ifdef::telemetrum[]
                        TeleDongle v3::
 
@@ -141,7 +163,7 @@
                        Connect pin 4 on the CPU to 3.3V, which can be done by
                        connecting pin 1 to pin 4.  Pin 1 is the left pin on
                        the lower edge of the chip when the unit is oriented
-                       such taht the SMA is at the top.
+                       such that the SMA is at the top.
 
                        TeleBT v4::