</para>
</legalnotice>
<revhistory>
+ <revision>
+ <revnumber>1.2</revnumber>
+ <date>14 April 2013</date>
+ <revremark>
+ Updated for software version 1.2. Version 1.2 adds support
+ for TeleBT and AltosDroid. It also adds a few minor features
+ and fixes a few minor bugs in AltosUI and the AltOS firmware.
+ </revremark>
+ </revision>
<revision>
<revnumber>1.1.1</revnumber>
<date>16 September 2012</date>
tower with a screw-driver trying to turn on your avionics before
installing igniters!
</para>
+ <para>
+ TeleMini is configured via the radio link. Of course, that
+ means you need to know the TeleMini radio configuration values
+ or you won't be able to communicate with it. For situations
+ when you don't have the radio configuration values, TeleMini
+ offers an 'emergency recovery' mode. In this mode, TeleMini is
+ configured as follows:
+ <itemizedlist>
+ <listitem>
+ Sets the radio frequency to 434.550MHz
+ </listitem>
+ <listitem>
+ Sets the radio calibration back to the factory value.
+ </listitem>
+ <listitem>
+ Sets the callsign to N0CALL
+ </listitem>
+ <listitem>
+ Does not go to 'pad' mode after five seconds.
+ </listitem>
+ </itemizedlist>
+ </para>
+ <para>
+ To get into 'emergency recovery' mode, first find the row of
+ four small holes opposite the switch wiring. Using a short
+ piece of small gauge wire, connect the outer two holes
+ together, then power TeleMini up. Once the red LED is lit,
+ disconnect the wire and the board should signal that it's in
+ 'idle' mode after the initial five second startup period.
+ </para>
</section>
<section>
<title>GPS </title>
</para>
</section>
</chapter>
+ <chapter>
+ <title>AltosDroid</title>
+ <para>
+ AltosDroid provides the same flight monitoring capabilities as
+ AltosUI, but runs on Android devices and is designed to connect
+ to a TeleBT receiver over Bluetoothâ„¢. Altos Droid monitors
+ telemetry data, logging it to internal storage in the Android
+ device, and presents that data in a UI the same way the 'Monitor
+ Flight' window does in AltosUI.
+ </para>
+ <para>
+ This manual will explain how to configure AltosDroid, connect
+ to TeleBT, operate the flight monitoring interface and describe
+ what the displayed data means.
+ </para>
+ <section>
+ <title>Installing AltosDroid</title>
+ <para>
+ AltosDroid is included in the Google Play store. To install
+ it on your Android device, open open the Google Play Store
+ application and search for "altosdroid". Make sure you don't
+ have a space between "altos" and "droid" or you probably won't
+ find what you want. That should bring you to the right page
+ from which you can download and install the application.
+ </para>
+ </section>
+ <section>
+ <title>Connecting to TeleBT</title>
+ </section>
+ <section>
+ <title>Configuring AltosDroid</title>
+ </section>
+ <section>
+ <title>Flight Monitoring</title>
+ </section>
+ <section>
+ <title>Downloading Flight Logs</title>
+ </section>
+ </chapter>
<chapter>
<title>Using Altus Metrum Products</title>
<section>
<appendix
xmlns:xi="http://www.w3.org/2001/XInclude">
<title>Release Notes</title>
+ <simplesect><title>Version 1.2</title><xi:include href="release-notes-1.2.xsl" xpointer="xpointer(/article/*)"/></simplesect>
<simplesect><title>Version 1.1.1</title><xi:include href="release-notes-1.1.1.xsl" xpointer="xpointer(/article/*)"/></simplesect>
<simplesect><title>Version 1.1</title><xi:include href="release-notes-1.1.xsl" xpointer="xpointer(/article/*)"/></simplesect>
<simplesect><title>Version 1.0.1</title><xi:include href="release-notes-1.0.1.xsl" xpointer="xpointer(/article/*)"/></simplesect>