-<?xml version="1.0" encoding="utf-8" ?>
+<?xml version="1.0" encoding="utf-8"?>
<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook XML V4.5//EN"
"/usr/share/xml/docbook/schema/dtd/4.5/docbookx.dtd">
<book>
<title>The Altus Metrum System</title>
- <subtitle>An Owner's Manual for TeleMetrum, TeleMini and TeleDongle Devices</subtitle>
+ <subtitle>An Owner's Manual for TeleMetrum, TeleMini, TeleDongle and TeleBT Devices</subtitle>
<bookinfo>
<author>
<firstname>Bdale</firstname>
<surname>Towns</surname>
</author>
<copyright>
- <year>2011</year>
+ <year>2013</year>
<holder>Bdale Garbee and Keith Packard</holder>
</copyright>
<legalnotice>
</para>
</legalnotice>
<revhistory>
+ <revision>
+ <revnumber>1.3</revnumber>
+ <date>12 November 2013</date>
+ <revremark>
+ Updated for software version 1.3. Version 1.3 adds support
+ for TeleMega, TeleMetrum v2.0, TeleMini v2.0 and EasyMini
+ and fixes bugs in AltosUI and the AltOS firmware.
+ </revremark>
+ </revision>
+ <revision>
+ <revnumber>1.2.1</revnumber>
+ <date>21 May 2013</date>
+ <revremark>
+ Updated for software version 1.2. Version 1.2 adds support
+ for TeleBT and AltosDroid. It also adds a few minor features
+ and fixes bugs in AltosUI and the AltOS firmware.
+ </revremark>
+ </revision>
+ <revision>
+ <revnumber>1.2</revnumber>
+ <date>18 April 2013</date>
+ <revremark>
+ Updated for software version 1.2. Version 1.2 adds support
+ for MicroPeak and the MicroPeak USB interface.
+ </revremark>
+ </revision>
+ <revision>
+ <revnumber>1.1.1</revnumber>
+ <date>16 September 2012</date>
+ <revremark>
+ Updated for software version 1.1.1 Version 1.1.1 fixes a few
+ bugs found in version 1.1.
+ </revremark>
+ </revision>
+ <revision>
+ <revnumber>1.1</revnumber>
+ <date>13 September 2012</date>
+ <revremark>
+ Updated for software version 1.1. Version 1.1 has new
+ features but is otherwise compatible with version 1.0.
+ </revremark>
+ </revision>
<revision>
<revnumber>1.0</revnumber>
<date>24 August 2011</date>
</revision>
</revhistory>
</bookinfo>
- <acknowledgements>
+ <dedication>
+ <title>Acknowledgements</title>
<para>
Thanks to Bob Finch, W9YA, NAR 12965, TRA 12350 for writing "The
Mere-Mortals Quick Start/Usage Guide to the Altus Metrum Starter
NAR #88757, TRA #12200
</literallayout>
</para>
- </acknowledgements>
+ </dedication>
<chapter>
<title>Introduction and Overview</title>
<para>
The first device created for our community was TeleMetrum, a dual
deploy altimeter with fully integrated GPS and radio telemetry
as standard features, and a "companion interface" that will
- support optional capabilities in the future.
+ support optional capabilities in the future. The latest version
+ of TeleMetrum, v2.0, has all of the same features but with
+ improved sensors and radio to offer increased performance.
+ </para>
+ <para>
+ Our second device was TeleMini, a dual deploy altimeter with
+ radio telemetry and radio direction finding. The first version
+ of this device was only 13mm by 38mm (½ inch by 1½ inches) and
+ could fit easily in an 18mm air-frame. The latest version, v2.0,
+ includes a beeper, USB data download and extended on-board
+ flight logging, along with an improved barometric sensor.
</para>
<para>
- The newest device is TeleMini, a dual deploy altimeter with
- radio telemetry and radio direction finding. This device is only
- 13mm by 38mm (½ inch by 1½ inches) and can fit easily in an 18mm
- air-frame.
+ TeleMega is our most sophisticated device, including six pyro
+ channels (four of which are fully programmable), integrated GPS,
+ integrated gyroscopes for staging/air-start inhibit and high
+ performance telemetry.
</para>
<para>
- Complementing TeleMetrum and TeleMini is TeleDongle, a USB to RF
- interface for communicating with the altimeters. Combined with your
- choice of antenna and
- notebook computer, TeleDongle and our associated user interface software
- form a complete ground station capable of logging and displaying in-flight
- telemetry, aiding rocket recovery, then processing and archiving flight
+ EasyMini is a dual-deploy altimeter with logging and built-in
+ USB data download.
+ </para>
+ <para>
+ TeleDongle was our first ground station, providing a USB to RF
+ interfaces for communicating with the altimeters. Combined with
+ your choice of antenna and notebook computer, TeleDongle and our
+ associated user interface software form a complete ground
+ station capable of logging and displaying in-flight telemetry,
+ aiding rocket recovery, then processing and archiving flight
data for analysis and review.
</para>
+ <para>
+ For a slightly more portable ground station experience that also
+ provides direct rocket recovery support, TeleBT offers flight
+ monitoring and data logging using a Bluetooth connection between
+ the receiver and an Android device that has the Altos Droid
+ application installed from the Google Play store.
+ </para>
<para>
More products will be added to the Altus Metrum family over time, and
we currently envision that this will be a single, comprehensive manual
"starter kit" is to charge the battery.
</para>
<para>
- The TeleMetrum battery can be charged by plugging it into the
- corresponding socket of the TeleMetrum and then using the USB A to
- mini B
- cable to plug the TeleMetrum into your computer's USB socket. The
- TeleMetrum circuitry will charge the battery whenever it is plugged
- in, because the TeleMetrum's on-off switch does NOT control the
+ For TeleMetrum and TeleMega, the battery can be charged by plugging it into the
+ corresponding socket of the device and then using the USB
+ cable to plug the flight computer into your computer's USB socket. The
+ on-board circuitry will charge the battery whenever it is plugged
+ in, because the on-off switch does NOT control the
charging circuitry.
</para>
<para>
- When the GPS chip is initially searching for
- satellites, TeleMetrum will consume more current than it can pull
- from the USB port, so the battery must be attached in order to get
- satellite lock. Once GPS is locked, the current consumption goes back
- down enough to enable charging while
- running. So it's a good idea to fully charge the battery as your
- first item of business so there is no issue getting and maintaining
- satellite lock. The yellow charge indicator led will go out when the
- battery is nearly full and the charger goes to trickle charge. It
- can take several hours to fully recharge a deeply discharged battery.
+ On TeleMetrum v1 boards, when the GPS chip is initially
+ searching for satellites, TeleMetrum will consume more current
+ than it can pull from the USB port, so the battery must be
+ attached in order to get satellite lock. Once GPS is locked,
+ the current consumption goes back down enough to enable charging
+ while running. So it's a good idea to fully charge the battery
+ as your first item of business so there is no issue getting and
+ maintaining satellite lock. The yellow charge indicator led
+ will go out when the battery is nearly full and the charger goes
+ to trickle charge. It can take several hours to fully recharge a
+ deeply discharged battery.
+ </para>
+ <para>
+ TeleMetrum v2.0 and TeleMega use a higher power battery charger,
+ allowing them to charge the battery while running the board at
+ maximum power. When the battery is charging, or when the board
+ is consuming a lot of power, the red LED will be lit. When the
+ battery is fully charged, the green LED will be lit. When the
+ battery is damaged or missing, both LEDs will be lit, which
+ appears yellow.
</para>
<para>
- The TeleMini battery can be charged by disconnecting it from the
- TeleMini board and plugging it into a standalone battery charger
- board, and connecting that via a USB cable to a laptop or other USB
- power source
+ The Lithium Polymer TeleMini and EasyMini battery can be charged by
+ disconnecting it from the board and plugging it into a
+ standalone battery charger such as the LipoCharger product
+ included in TeleMini Starter Kits, and connecting that via a USB
+ cable to a laptop or other USB power source.
+ </para>
+ <para>
+ You can also choose to use another battery with TeleMini v2.0
+ and EasyMini, anything supplying between 4 and 12 volts should
+ work fine (like a standard 9V battery), but if you are planning
+ to fire pyro charges, ground testing is required to verify that
+ the battery supplies enough current.
</para>
<para>
The other active device in the starter kit is the TeleDongle USB to
ugly bugs in some earlier versions.
</para>
<para>
- Next you should obtain and install the AltOS software. These include
- the AltosUI ground station program, current firmware images for
- TeleMetrum, TeleMini and TeleDongle, and a number of standalone
- utilities that are rarely needed. Pre-built binary packages are
- available for Linux, Microsoft Windows, and recent MacOSX versions.
- Full source code and build instructions are also available.
- The latest version may always be downloaded from
+ Next you should obtain and install the AltOS software. These
+ include the AltosUI ground station program, current firmware
+ images for all of the hardware, and a number of standalone
+ utilities that are rarely needed. Pre-built binary packages are
+ available for Linux, Microsoft Windows, and recent MacOSX
+ versions. Full source code and build instructions are also
+ available. The latest version may always be downloaded from
<ulink url="http://altusmetrum.org/AltOS"/>.
</para>
+ <para>
+ If you're using a TeleBT instead of the TeleDongle, you'll want
+ to go install the Altos Droid application from the Google Play
+ store. You don't need a data plan to use Altos Droid, but
+ without network access, the Map view will be less useful as it
+ won't contain any map data. You can also use TeleBT connected
+ over USB with your laptop computer; it acts exactly like a
+ TeleDongle. Anywhere this manual talks about TeleDongle, you can
+ also read that as 'and TeleBT when connected via USB'.
+ </para>
</chapter>
<chapter>
<title>Handling Precautions</title>
strapping them down, for example.
</para>
<para>
- The barometric sensors used on both TeleMetrum and TeleMini are
- sensitive to sunlight. In normal TeleMetrum mounting situations, it
+ The barometric sensors used on all of our flight computers are
+ sensitive to sunlight. In normal mounting situations, the baro sensor
and all of the other surface mount components
are "down" towards whatever the underlying mounting surface is, so
this is not normally a problem. Please consider this, though, when
designing an installation, for example, in an air-frame with a
see-through plastic payload bay. It is particularly important to
- consider this with TeleMini, both because the baro sensor is on the
+ consider this with TeleMini v1.0, both because the baro sensor is on the
"top" of the board, and because many model rockets with payload bays
use clear plastic for the payload bay! Replacing these with an opaque
cardboard tube, painting them, or wrapping them with a layer of masking
<chapter>
<title>Hardware Overview</title>
<para>
- TeleMetrum is a 1 inch by 2.75 inch circuit board. It was designed to
+ TeleMetrum is a 1 inch by 2¾ inch circuit board. It was designed to
fit inside coupler for 29mm air-frame tubing, but using it in a tube that
small in diameter may require some creativity in mounting and wiring
to succeed! The presence of an accelerometer means TeleMetrum should
bay for TeleMetrum should have at least 10 inches of interior length.
</para>
<para>
- TeleMini is a 0.5 inch by 1.5 inch circuit board. It was designed to
+ TeleMini v1.0 is a ½ inch by 1½ inch circuit board. It was designed to
fit inside an 18mm air-frame tube, but using it in a tube that
small in diameter may require some creativity in mounting and wiring
to succeed! Since there is no accelerometer, TeleMini can be mounted
- in any convenient orientation. The default 1/4
+ in any convenient orientation. The default ¼
wave UHF wire antenna attached to the center of one end of
the board is about 7 inches long, and wiring for a power switch and
the e-matches for apogee and main ejection charges depart from the
bay for TeleMini should have at least 9 inches of interior length.
</para>
<para>
- A typical TeleMetrum or TeleMini installation involves attaching
- only a suitable Lithium Polymer battery, a single pole switch for
+ TeleMini v2.0 and EasyMini are both built on a 0.8 inch by 1½
+ inch circuit board. They're designed to fit in a 24mm coupler
+ tube. TeleMini has an antenna, which must be run straight out
+ fro the board. Bending or folding it will dramatically reduce RF
+ performance. For smaller rockets, it's often best to drill a
+ hole in the bulkhead forward of TeleMini and run the antenna
+ wire through that and alongside any recovery components
+ there. Be careful to seal the hole to prevent ejection gasses
+ from passing through the hole and damaging the electronics.
+ </para>
+ <para>
+ TeleMega is a 1¼ inch by 3¼ inch circuit board. It was
+ designed to easily fit in a 38mm coupler. Like TeleMetrum,
+ TeleMega has an accelerometer and so it must be mounted so that
+ the board is aligned with the flight axis. It can be mounted
+ either antenna up or down.
+ </para>
+ <para>
+ A typical installation involves attaching
+ only a suitable battery, a single pole switch for
power on/off, and two pairs of wires connecting e-matches for the
apogee and main ejection charges. All Altus Metrum products are
- designed for use with single-cell batteries with 3.7 volts nominal.
+ designed for use with single-cell batteries with 3.7 volts
+ nominal. TeleMini v2.0 and EasyMini may also be used with other
+ batteries as long as they supply between 4 and 12 volts.
+ </para>
+ <para>
+ The battery connectors are a standard 2-pin JST connector and
+ match batteries sold by Spark Fun. These batteries are
+ single-cell Lithium Polymer batteries that nominally provide 3.7
+ volts. Other vendors sell similar batteries for RC aircraft
+ using mating connectors, however the polarity for those is
+ generally reversed from the batteries used by Altus Metrum
+ products. In particular, the Tenergy batteries supplied for use
+ in Featherweight flight computers are not compatible with Altus
+ Metrum flight computers or battery chargers. <emphasis>Check
+ polarity and voltage before connecting any battery not purchased
+ from Altus Metrum or Spark Fun.</emphasis>
</para>
<para>
- By default, we use the unregulated output of the Li-Po battery directly
+ By default, we use the unregulated output of the battery directly
to fire ejection charges. This works marvelously with standard
low-current e-matches like the J-Tek from MJG Technologies, and with
Quest Q2G2 igniters. However, if you want or need to use a separate
jeweler's screwdriver set.
</para>
<para>
- TeleMetrum also uses the screw terminal block for the power
- switch leads. On TeleMini, the power switch leads are soldered
- directly to the board and can be connected directly to a switch.
+ Except for TeleMini v1.0, the flight computers also use the
+ screw terminal block for the power switch leads. On TeleMini v1.0,
+ the power switch leads are soldered directly to the board and
+ can be connected directly to a switch.
</para>
<para>
For most air-frames, the integrated antennas are more than
metal electronics bay which is opaque to RF signals, you may need to
use off-board external antennas instead. In this case, you can
order an altimeter with an SMA connector for the UHF antenna
- connection, and, on TeleMetrum, you can unplug the integrated GPS
+ connection, and, on TeleMetrum v1, you can unplug the integrated GPS
antenna and select an appropriate off-board GPS antenna with
cable terminating in a U.FL connector.
</para>
TeleMetrum assumes it's on a rail or rod being prepared for
launch, so the firmware chooses flight mode. However, if the
rocket is more or less horizontal, the firmware instead enters
- idle mode. Since TeleMini doesn't have an accelerometer we can
- use to determine orientation, "idle" mode is selected when the
- board receives a command packet within the first five seconds
- of operation; if no packet is received, the board enters
- "flight" mode.
+ idle mode. Since TeleMini v2.0 and EasyMini don't have an
+ accelerometer we can use to determine orientation, "idle" mode
+ is selected if the board is connected via USB to a computer,
+ otherwise the board enters "flight" mode. TeleMini v1.0
+ selects "idle" mode if it receives a command packet within the
+ first five seconds of operation.
</para>
<para>
At power on, you will hear three beeps or see three flashes
flights, do what makes sense.
</para>
<para>
- If idle mode is entered, you will hear an audible "di-dit" or see
- two short flashes ("I" for idle), and the flight state machine is
- disengaged, thus no ejection charges will fire. The altimeters also
- listen for the radio link when in idle mode for requests sent via
- TeleDongle. Commands can be issued to a TeleMetrum in idle mode
- over either
- USB or the radio link equivalently. TeleMini only has the radio link.
- Idle mode is useful for configuring the altimeter, for extracting data
- from the on-board storage chip after flight, and for ground testing
- pyro charges.
+ If idle mode is entered, you will hear an audible "di-dit" or
+ see two short flashes ("I" for idle), and the flight state
+ machine is disengaged, thus no ejection charges will fire.
+ The altimeters also listen for the radio link when in idle
+ mode for requests sent via TeleDongle. Commands can be issued
+ in idle mode over either USB or the radio link
+ equivalently. TeleMini v1.0 only has the radio link. Idle
+ mode is useful for configuring the altimeter, for extracting
+ data from the on-board storage chip after flight, and for
+ ground testing pyro charges.
</para>
<para>
- One "neat trick" of particular value when TeleMetrum is used with
+ One "neat trick" of particular value when TeleMetrum or TeleMega are used with
very large air-frames, is that you can power the board up while the
rocket is horizontal, such that it comes up in idle mode. Then you can
raise the air-frame to launch position, and issue a 'reset' command
tower with a screw-driver trying to turn on your avionics before
installing igniters!
</para>
+ <para>
+ TeleMini v1.0 is configured solely via the radio link. Of course, that
+ means you need to know the TeleMini radio configuration values
+ or you won't be able to communicate with it. For situations
+ when you don't have the radio configuration values, TeleMini v1.0
+ offers an 'emergency recovery' mode. In this mode, TeleMini is
+ configured as follows:
+ <itemizedlist>
+ <listitem>
+ <para>
+ Sets the radio frequency to 434.550MHz
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Sets the radio calibration back to the factory value.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Sets the callsign to N0CALL
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Does not go to 'pad' mode after five seconds.
+ </para>
+ </listitem>
+ </itemizedlist>
+ </para>
+ <para>
+ To get into 'emergency recovery' mode, first find the row of
+ four small holes opposite the switch wiring. Using a short
+ piece of small gauge wire, connect the outer two holes
+ together, then power TeleMini up. Once the red LED is lit,
+ disconnect the wire and the board should signal that it's in
+ 'idle' mode after the initial five second startup period.
+ </para>
</section>
<section>
<title>GPS </title>
<para>
- TeleMetrum includes a complete GPS receiver. A complete explanation
- of how GPS works is beyond the scope of this manual, but the bottom
- line is that the TeleMetrum GPS receiver needs to lock onto at least
- four satellites to obtain a solid 3 dimensional position fix and know
- what time it is.
+ TeleMetrum and TeleMega include a complete GPS receiver. A
+ complete explanation of how GPS works is beyond the scope of
+ this manual, but the bottom line is that the GPS receiver
+ needs to lock onto at least four satellites to obtain a solid
+ 3 dimensional position fix and know what time it is.
</para>
<para>
- TeleMetrum provides backup power to the GPS chip any time a
+ The flight computers provide backup power to the GPS chip any time a
battery is connected. This allows the receiver to "warm start" on
the launch rail much faster than if every power-on were a GPS
- "cold start". In typical operations, powering up TeleMetrum
+ "cold start". In typical operations, powering up
on the flight line in idle mode while performing final air-frame
preparation will be sufficient to allow the GPS receiver to cold
start and acquire lock. Then the board can be powered down during
<section>
<title>Controlling An Altimeter Over The Radio Link</title>
<para>
- One of the unique features of the Altus Metrum system is
- the ability to create a two way command link between TeleDongle
- and an altimeter using the digital radio transceivers built into
- each device. This allows you to interact with the altimeter from
- afar, as if it were directly connected to the computer.
+ One of the unique features of the Altus Metrum system is the
+ ability to create a two way command link between TeleDongle
+ and an altimeter using the digital radio transceivers
+ built into each device. This allows you to interact with the
+ altimeter from afar, as if it were directly connected to the
+ computer.
</para>
<para>
- Any operation which can be performed with TeleMetrum can
- either be done with TeleMetrum directly connected to the
+ Any operation which can be performed with a flight computer can
+ either be done with the device directly connected to the
computer via the USB cable, or through the radio
- link. TeleMini doesn't provide a USB connector and so it is
+ link. TeleMini v1.0 doesn't provide a USB connector and so it is
always communicated with over radio. Select the appropriate
TeleDongle device when the list of devices is presented and
AltosUI will interact with an altimeter over the radio link.
</listitem>
<listitem>
<para>
- Configure altimeter apogee delays or main deploy heights
+ Configure altimeter apogee delays, main deploy heights
+ and additional pyro event conditions
to respond to changing launch conditions. You can also
'reboot' the altimeter. Use this to remotely enable the
- flight computer by turning TeleMetrum on in "idle" mode,
+ flight computer by turning TeleMetrum or TeleMega on in "idle" mode,
then once the air-frame is oriented for launch, you can
reboot the altimeter and have it restart in pad mode
without having to climb the scary ladder.
<listitem>
<para>
Fire Igniters—Test your deployment charges without snaking
- wires out through holes in the air-frame. Simply assembly the
+ wires out through holes in the air-frame. Simply assemble the
rocket as if for flight with the apogee and main charges
loaded, then remotely command the altimeter to fire the
igniters.
close the window before performing other desired radio operations.
</para>
<para>
- TeleMetrum only enables radio commanding in 'idle' mode, so
- make sure you have TeleMetrum lying horizontally when you turn
- it on. Otherwise, TeleMetrum will start in 'pad' mode ready for
+ The flight computers only enable radio commanding in 'idle' mode.
+ TeleMetrum and TeleMega use the accelerometer to detect which orientation they
+ start up in, so make sure you have the flight computer lying horizontally when you turn
+ it on. Otherwise, it will start in 'pad' mode ready for
flight, and will not be listening for command packets from TeleDongle.
</para>
<para>
<para>
You can monitor the operation of the radio link by watching the
lights on the devices. The red LED will flash each time a packet
- is tramsitted, while the green LED will light up on TeleDongle when
+ is transmitted, while the green LED will light up on TeleDongle when
it is waiting to receive a packet from the altimeter.
</para>
</section>
An important aspect of preparing a rocket using electronic deployment
for flight is ground testing the recovery system. Thanks
to the bi-directional radio link central to the Altus Metrum system,
- this can be accomplished in a TeleMetrum or TeleMini equipped rocket
+ this can be accomplished in a TeleMega, TeleMetrum or TeleMini equipped rocket
with less work than you may be accustomed to with other systems. It
can even be fun!
</para>
<para>
Just prep the rocket for flight, then power up the altimeter
- in "idle" mode (placing air-frame horizontal for TeleMetrum or
- selected the Configure Altimeter tab for TeleMini). This will cause
+ in "idle" mode (placing air-frame horizontal for TeleMetrum or TeleMega, or
+ selecting the Configure Altimeter tab for TeleMini). This will cause
the firmware to go into "idle" mode, in which the normal flight
state machine is disabled and charges will not fire without
manual command. You can now command the altimeter to fire the apogee
data later...
</para>
<para>
- We don't use a 'normal packet radio' mode like APRS because they're
+ We don't generally use a 'normal packet radio' mode like APRS because they're
just too inefficient. The GFSK modulation we use is FSK with the
base-band pulses passed through a
Gaussian filter before they go into the modulator to limit the
altitudes over time, and would of course appreciate customer feedback
on performance in higher altitude flights!
</para>
+ <para>
+ However, TeleMetrum v2.0 and TeleMega can send APRS if
+ desired, the interval between APRS packets can be
+ configured. As each APRS packet takes a full second to
+ transmit, we recommend an interval of at least 5 seconds.
+ </para>
</section>
<section>
<title>Configurable Parameters</title>
<para>
Configuring an Altus Metrum altimeter for flight is very
- simple. Even on our baro-only TeleMini board, the use of a Kalman
+ simple. Even on our baro-only TeleMini and EasyMini boards, the use of a Kalman
filter means there is no need to set a "mach delay". The few
configurable parameters can all be set using AltosUI over USB or
or radio link via TeleDongle.
(10 samples/second), there's plenty of space to store many
flights worth of data.
</para>
+ <para>
+ TeleMetrum v2.0 and TeleMega have 8MB of on-board flash stroage, enough to hold
+ </para>
<para>
The on-board flash is partitioned into separate flight logs,
each of a fixed maximum size. Increase the maximum size of
incorrect data from being reported.
</para>
</listitem>
+ <listitem>
+ <para>
+ The age of the displayed data, in seconds since the last
+ successfully received telemetry packet. In normal operation
+ this will stay in the low single digits. If the number starts
+ counting up, then you are no longer receiving data over the radio
+ link from the flight computer.
+ </para>
+ </listitem>
</itemizedlist>
<para>
Finally, the largest portion of the window contains a set of
</para>
</listitem>
</itemizedlist>
- <para>
- The Launchpad tab also shows the computed launch pad position
- and altitude, averaging many reported positions to improve the
- accuracy of the fix.
- </para>
</para>
+ <para>
+ The Launchpad tab also shows the computed launch pad position
+ and altitude, averaging many reported positions to improve the
+ accuracy of the fix.
+ </para>
</section>
<section>
<title>Ascent</title>
be below 10m/s when under the main parachute in a dual-deploy flight.
</para>
<para>
- For TeleMetrum altimeters, you can locate the rocket in the sky
- using the elevation and
- bearing information to figure out where to look. Elevation is
- in degrees above the horizon. Bearing is reported in degrees
- relative to true north. Range can help figure out how big the
- rocket will appear. Note that all of these values are relative
- to the pad location. If the elevation is near 90°, the rocket
- is over the pad, not over you.
+ For TeleMetrum altimeters, you can locate the rocket in the
+ sky using the elevation and bearing information to figure
+ out where to look. Elevation is in degrees above the
+ horizon. Bearing is reported in degrees relative to true
+ north. Range can help figure out how big the rocket will
+ appear. Ground Distance shows how far it is to a point
+ directly under the rocket and can help figure out where the
+ rocket is likely to land. Note that all of these values are
+ relative to the pad location. If the elevation is near 90°,
+ the rocket is over the pad, not over you.
</para>
<para>
Finally, the igniter voltages are reported in this tab as
flash memory.
</para>
<para>
- Once a flight record is selected, a window with two tabs is
+ Once a flight record is selected, a window with four tabs is
opened. The first tab contains a graph with acceleration
(blue), velocity (green) and altitude (red) of the flight,
- measured in metric units. The
- apogee(yellow) and main(magenta) igniter voltages are also
- displayed; high voltages indicate continuity, low voltages
- indicate open circuits. The second tab contains some basic
- flight statistics.
+ measured in metric units. The apogee(yellow) and main(magenta)
+ igniter voltages are also displayed; high voltages indicate
+ continuity, low voltages indicate open circuits. The second
+ tab lets you configure which data to show in the graph. The
+ third contains some basic flight statistics while the fourth
+ has a map with the ground track of the flight displayed.
</para>
<para>
The graph can be zoomed into a particular area by clicking and
with the AltosUI operators call sign as needed to comply with
your local radio regulations.
</para>
+ <para>
+ Note that to successfully command a flight computer over the radio
+ (to configure the altimeter, monitor idle, or fire pyro charges),
+ the callsign configured here must exactly match the callsign
+ configured in the flight computer. This matching is case
+ sensitive.
+ </para>
+ </section>
+ <section>
+ <title>Imperial Units</title>
+ <para>
+ This switches between metric units (meters) and imperial
+ units (feet and miles). This affects the display of values
+ use during flight monitoring, data graphing and all of the
+ voice announcements. It does not change the units used when
+ exporting to CSV files, those are always produced in metric units.
+ </para>
</section>
<section>
<title>Font Size</title>
</para>
</section>
</section>
+ <section>
+ <title>Configure Groundstation</title>
+ <para>
+ Select this button and then select a TeleDongle Device from the list provided.
+ </para>
+ <para>
+ The first few lines of the dialog provide information about the
+ connected device, including the product name,
+ software version and hardware serial number. Below that are the
+ individual configuration entries.
+ </para>
+ <para>
+ Note that the TeleDongle itself doesn't save any configuration
+ data, the settings here are recorded on the local machine in
+ the Java preferences database. Moving the TeleDongle to
+ another machine, or using a different user account on the same
+ machine will cause settings made here to have no effect.
+ </para>
+ <para>
+ At the bottom of the dialog, there are three buttons:
+ </para>
+ <itemizedlist>
+ <listitem>
+ <para>
+ Save. This writes any changes to the
+ local Java preferences file. If you don't
+ press this button, any changes you make will be lost.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Reset. This resets the dialog to the most recently saved values,
+ erasing any changes you have made.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Close. This closes the dialog. Any unsaved changes will be
+ lost.
+ </para>
+ </listitem>
+ </itemizedlist>
+ <para>
+ The rest of the dialog contains the parameters to be configured.
+ </para>
+ <section>
+ <title>Frequency</title>
+ <para>
+ This configures the frequency to use for both telemetry and
+ packet command mode. Set this before starting any operation
+ involving packet command mode so that it will use the right
+ frequency. Telemetry monitoring mode also provides a menu to
+ change the frequency, and that menu also sets the same Java
+ preference value used here.
+ </para>
+ </section>
+ <section>
+ <title>Radio Calibration</title>
+ <para>
+ The radios in every Altus Metrum device are calibrated at the
+ factory to ensure that they transmit and receive on the
+ specified frequency. To change a TeleDongle's calibration,
+ you must reprogram the unit completely, so this entry simply
+ shows the current value and doesn't allow any changes.
+ </para>
+ </section>
+ </section>
<section>
<title>Flash Image</title>
<para>
</para>
</section>
</chapter>
+ <chapter>
+ <title>AltosDroid</title>
+ <para>
+ AltosDroid provides the same flight monitoring capabilities as
+ AltosUI, but runs on Android devices and is designed to connect
+ to a TeleBT receiver over Bluetooth™. Altos Droid monitors
+ telemetry data, logging it to internal storage in the Android
+ device, and presents that data in a UI the same way the 'Monitor
+ Flight' window does in AltosUI.
+ </para>
+ <para>
+ This manual will explain how to configure AltosDroid, connect
+ to TeleBT, operate the flight monitoring interface and describe
+ what the displayed data means.
+ </para>
+ <section>
+ <title>Installing AltosDroid</title>
+ <para>
+ AltosDroid is included in the Google Play store. To install
+ it on your Android device, open open the Google Play Store
+ application and search for "altosdroid". Make sure you don't
+ have a space between "altos" and "droid" or you probably won't
+ find what you want. That should bring you to the right page
+ from which you can download and install the application.
+ </para>
+ </section>
+ <section>
+ <title>Connecting to TeleBT</title>
+ <para>
+ Press the Android 'Menu' button or soft-key to see the
+ configuration options available. Select the 'Connect a device'
+ option and then the 'Scan for devices' entry at the bottom to
+ look for your TeleBT device. Select your device, and when it
+ asks for the code, enter '1234'.
+ </para>
+ <para>
+ Subsequent connections will not require you to enter that
+ code, and your 'paired' device will appear in the list without
+ scanning.
+ </para>
+ </section>
+ <section>
+ <title>Configuring AltosDroid</title>
+ <para>
+ The only configuration option available for AltosDroid is
+ which frequency to listen on. Press the Android 'Menu' button
+ or soft-key and pick the 'Select radio frequency' entry. That
+ brings up a menu of pre-set radio frequencies; pick the one
+ which matches your altimeter.
+ </para>
+ </section>
+ <section>
+ <title>Altos Droid Flight Monitoring</title>
+ <para>
+ Altos Droid is designed to mimic the AltosUI flight monitoring
+ display, providing separate tabs for each stage of your rocket
+ flight along with a tab containing a map of the local area
+ with icons marking the current location of the altimeter and
+ the Android device.
+ </para>
+ <section>
+ <title>Pad</title>
+ <para>
+ The 'Launch Pad' tab shows information used to decide when the
+ rocket is ready for flight. The first elements include red/green
+ indicators, if any of these is red, you'll want to evaluate
+ whether the rocket is ready to launch:
+ <itemizedlist>
+ <listitem>
+ <para>
+ Battery Voltage. This indicates whether the Li-Po battery
+ powering the TeleMetrum has sufficient charge to last for
+ the duration of the flight. A value of more than
+ 3.7V is required for a 'GO' status.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Apogee Igniter Voltage. This indicates whether the apogee
+ igniter has continuity. If the igniter has a low
+ resistance, then the voltage measured here will be close
+ to the Li-Po battery voltage. A value greater than 3.2V is
+ required for a 'GO' status.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Main Igniter Voltage. This indicates whether the main
+ igniter has continuity. If the igniter has a low
+ resistance, then the voltage measured here will be close
+ to the Li-Po battery voltage. A value greater than 3.2V is
+ required for a 'GO' status.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ On-board Data Logging. This indicates whether there is
+ space remaining on-board to store flight data for the
+ upcoming flight. If you've downloaded data, but failed
+ to erase flights, there may not be any space
+ left. TeleMetrum can store multiple flights, depending
+ on the configured maximum flight log size. TeleMini
+ stores only a single flight, so it will need to be
+ downloaded and erased after each flight to capture
+ data. This only affects on-board flight logging; the
+ altimeter will still transmit telemetry and fire
+ ejection charges at the proper times.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ GPS Locked. For a TeleMetrum device, this indicates whether the GPS receiver is
+ currently able to compute position information. GPS requires
+ at least 4 satellites to compute an accurate position.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ GPS Ready. For a TeleMetrum device, this indicates whether GPS has reported at least
+ 10 consecutive positions without losing lock. This ensures
+ that the GPS receiver has reliable reception from the
+ satellites.
+ </para>
+ </listitem>
+ </itemizedlist>
+ </para>
+ <para>
+ The Launchpad tab also shows the computed launch pad position
+ and altitude, averaging many reported positions to improve the
+ accuracy of the fix.
+ </para>
+ </section>
+ </section>
+ <section>
+ <title>Downloading Flight Logs</title>
+ <para>
+ Altos Droid always saves every bit of telemetry data it
+ receives. To download that to a computer for use with AltosUI,
+ simply remove the SD card from your Android device, or connect
+ your device to your computer's USB port and browse the files
+ on that device. You will find '.telem' files in the TeleMetrum
+ directory that will work with AltosUI directly.
+ </para>
+ </section>
+ </chapter>
<chapter>
<title>Using Altus Metrum Products</title>
<section>
<title>On the Ground</title>
<para>
To receive the data stream from the rocket, you need an antenna and short
- feed-line connected to one of our <ulink url="http://www.altusmetrum.org/TeleDongle/">TeleDongle</ulink> units. The
+ feed-line connected to one of our <ulink url="http://www.altusmetrum.org/TeleDongle/">TeleDongle</ulink> units. If possible, use an SMA to BNC
+ adapter instead of feedline between the antenna feedpoint and
+ TeleDongle, as this will give you the best performance. The
TeleDongle in turn plugs directly into the USB port on a notebook
computer. Because TeleDongle looks like a simple serial port, your computer
does not require special device drivers... just plug it in.
So, to recap, on the ground the hardware you'll need includes:
<orderedlist inheritnum='inherit' numeration='arabic'>
<listitem>
- an antenna and feed-line
+ <para>
+ an antenna and feed-line or adapter
+ </para>
</listitem>
<listitem>
- a TeleDongle
+ <para>
+ a TeleDongle
+ </para>
</listitem>
<listitem>
- a notebook computer
+ <para>
+ a notebook computer
+ </para>
</listitem>
<listitem>
- optionally, a hand-held GPS receiver
+ <para>
+ optionally, a hand-held GPS receiver
+ </para>
</listitem>
<listitem>
- optionally, an HT or receiver covering 435 MHz
+ <para>
+ optionally, an HT or receiver covering 435 MHz
+ </para>
</listitem>
</orderedlist>
</para>
Arrow Antennas.
</ulink>
The 440-3 and 440-5 are both good choices for finding a
- TeleMetrum- or TeleMini- equipped rocket when used with a suitable 70cm HT.
+ TeleMetrum- or TeleMini- equipped rocket when used with a suitable
+ 70cm HT. TeleDongle and an SMA to BNC adapter fit perfectly
+ between the driven element and reflector of Arrow antennas.
</para>
</section>
<section>
<section>
<title>Future Plans</title>
<para>
- In the future, we intend to offer "companion boards" for the rocket that will
- plug in to TeleMetrum to collect additional data, provide more pyro channels,
- and so forth.
+ In the future, we intend to offer "companion boards" for the rocket
+ that will plug in to TeleMetrum to collect additional data, provide
+ more pyro channels, and so forth.
+ </para>
+ <para>
+ Also under design is a new flight computer with more sensors, more
+ pyro channels, and a more powerful radio system designed for use
+ in multi-stage, complex, and extreme altitude projects.
</para>
<para>
- We are also working on the design of a hand-held ground terminal that will
- allow monitoring the rocket's status, collecting data during flight, and
- logging data after flight without the need for a notebook computer on the
- flight line. Particularly since it is so difficult to read most notebook
- screens in direct sunlight, we think this will be a great thing to have.
+ We are also working on alternatives to TeleDongle. One is a
+ a stand-alone, hand-held ground terminal that will allow monitoring
+ the rocket's status, collecting data during flight, and logging data
+ after flight without the need for a notebook computer on the
+ flight line. Particularly since it is so difficult to read most
+ notebook screens in direct sunlight, we think this will be a great
+ thing to have. We are also working on a TeleDongle variant with
+ Bluetooth that will work with Android phones and tablets.
</para>
<para>
- Because all of our work is open, both the hardware designs and the software,
- if you have some great idea for an addition to the current Altus Metrum family,
- feel free to dive in and help! Or let us know what you'd like to see that
- we aren't already working on, and maybe we'll get excited about it too...
+ Because all of our work is open, both the hardware designs and the
+ software, if you have some great idea for an addition to the current
+ Altus Metrum family, feel free to dive in and help! Or let us know
+ what you'd like to see that we aren't already working on, and maybe
+ we'll get excited about it too...
+ </para>
+ <para>
+ Watch our
+ <ulink url="http://altusmetrum.org/">web site</ulink> for more news
+ and information as our family of products evolves!
</para>
</section>
</chapter>
</para>
<orderedlist inheritnum='inherit' numeration='arabic'>
<listitem>
- Make sure TeleMetrum is aligned precisely along the axis of
- acceleration so that the accelerometer can accurately
- capture data during the flight.
+ <para>
+ Make sure TeleMetrum is aligned precisely along the axis of
+ acceleration so that the accelerometer can accurately
+ capture data during the flight.
+ </para>
</listitem>
<listitem>
- Watch for any metal touching components on the
- board. Shorting out connections on the bottom of the board
- can cause the altimeter to fail during flight.
+ <para>
+ Watch for any metal touching components on the
+ board. Shorting out connections on the bottom of the board
+ can cause the altimeter to fail during flight.
+ </para>
</listitem>
</orderedlist>
</section>
attenuate the GPS signal.
<orderedlist inheritnum='inherit' numeration='arabic'>
<listitem>
- Conductive tubing or coatings. Carbon fiber and metal
- tubing, or metallic paint will all dramatically attenuate the
- GPS signal. We've never heard of anyone successfully
- receiving GPS from inside these materials.
+ <para>
+ Conductive tubing or coatings. Carbon fiber and metal
+ tubing, or metallic paint will all dramatically attenuate the
+ GPS signal. We've never heard of anyone successfully
+ receiving GPS from inside these materials.
+ </para>
</listitem>
<listitem>
- Metal components near the GPS patch antenna. These will
- de-tune the patch antenna, changing the resonant frequency
- away from the L1 carrier and reduce the effectiveness of the
- antenna. You can place as much stuff as you like beneath the
- antenna as that's covered with a ground plane. But, keep
- wires and metal out from above the patch antenna.
+ <para>
+ Metal components near the GPS patch antenna. These will
+ de-tune the patch antenna, changing the resonant frequency
+ away from the L1 carrier and reduce the effectiveness of the
+ antenna. You can place as much stuff as you like beneath the
+ antenna as that's covered with a ground plane. But, keep
+ wires and metal out from above the patch antenna.
+ </para>
</listitem>
</orderedlist>
</para>
</para>
<itemizedlist>
<listitem>
- Keep wires from different circuits apart. Moving circuits
- further apart will reduce RFI.
+ <para>
+ Keep wires from different circuits apart. Moving circuits
+ further apart will reduce RFI.
+ </para>
</listitem>
<listitem>
+ <para>
Avoid parallel wires from different circuits. The longer two
wires run parallel to one another, the larger the amount of
transferred energy. Cross wires at right angles to reduce
RFI.
+ </para>
</listitem>
<listitem>
+ <para>
Twist wires from the same circuits. Two wires the same
distance from the transmitter will get the same amount of
induced energy which will then cancel out. Any time you have
even out distances and reduce RFI. For altimeters, this
includes battery leads, switch hookups and igniter
circuits.
+ </para>
</listitem>
<listitem>
+ <para>
Avoid resonant lengths. Know what frequencies are present
in the environment and avoid having wire lengths near a
natural resonant length. Altusmetrum products transmit on the
70cm amateur band, so you should avoid lengths that are a
simple ratio of that length; essentially any multiple of 1/4
of the wavelength (17.5cm).
+ </para>
</listitem>
</itemizedlist>
</section>
<title>Updating TeleMetrum Firmware</title>
<orderedlist inheritnum='inherit' numeration='arabic'>
<listitem>
+ <para>
Find the 'programming cable' that you got as part of the starter
kit, that has a red 8-pin MicroMaTch connector on one end and a
red 4-pin MicroMaTch connector on the other end.
+ </para>
</listitem>
<listitem>
+ <para>
Take the 2 screws out of the TeleDongle case to get access
to the circuit board.
+ </para>
</listitem>
<listitem>
+ <para>
Plug the 8-pin end of the programming cable to the
matching connector on the TeleDongle, and the 4-pin end to the
matching connector on the TeleMetrum.
Note that each MicroMaTch connector has an alignment pin that
goes through a hole in the PC board when you have the cable
oriented correctly.
+ </para>
</listitem>
<listitem>
+ <para>
Attach a battery to the TeleMetrum board.
+ </para>
</listitem>
<listitem>
+ <para>
Plug the TeleDongle into your computer's USB port, and power
up the TeleMetrum.
+ </para>
</listitem>
<listitem>
+ <para>
Run AltosUI, and select 'Flash Image' from the File menu.
+ </para>
</listitem>
<listitem>
+ <para>
Pick the TeleDongle device from the list, identifying it as the
programming device.
+ </para>
</listitem>
<listitem>
+ <para>
Select the image you want put on the TeleMetrum, which should have a
name in the form telemetrum-v1.2-1.0.0.ihx. It should be visible
in the default directory, if not you may have to poke around
your system to find it.
+ </para>
</listitem>
<listitem>
+ <para>
Make sure the configuration parameters are reasonable
looking. If the serial number and/or RF configuration
values aren't right, you'll need to change them.
+ </para>
</listitem>
<listitem>
+ <para>
Hit the 'OK' button and the software should proceed to flash
the TeleMetrum with new firmware, showing a progress bar.
+ </para>
</listitem>
<listitem>
+ <para>
Confirm that the TeleMetrum board seems to have updated OK, which you
can do by plugging in to it over USB and using a terminal program
to connect to the board and issue the 'v' command to check
the version, etc.
+ </para>
</listitem>
<listitem>
+ <para>
If something goes wrong, give it another try.
+ </para>
</listitem>
</orderedlist>
</section>
<title>Updating TeleMini Firmware</title>
<orderedlist inheritnum='inherit' numeration='arabic'>
<listitem>
+<para>
You'll need a special 'programming cable' to reprogram the
TeleMini. It's available on the Altus Metrum web store, or
you can make your own using an 8-pin MicroMaTch connector on
one end and a set of four pins on the other.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Take the 2 screws out of the TeleDongle case to get access
to the circuit board.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Plug the 8-pin end of the programming cable to the matching
connector on the TeleDongle, and the 4-pins into the holes
in the TeleMini circuit board. Note that the MicroMaTch
the PC board when you have the cable oriented correctly, and
that pin 1 on the TeleMini board is marked with a square pad
while the other pins have round pads.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Attach a battery to the TeleMini board.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Plug the TeleDongle into your computer's USB port, and power
up the TeleMini
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Run AltosUI, and select 'Flash Image' from the File menu.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Pick the TeleDongle device from the list, identifying it as the
programming device.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Select the image you want put on the TeleMini, which should have a
name in the form telemini-v1.0-1.0.0.ihx. It should be visible
in the default directory, if not you may have to poke around
your system to find it.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Make sure the configuration parameters are reasonable
looking. If the serial number and/or RF configuration
values aren't right, you'll need to change them.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Hit the 'OK' button and the software should proceed to flash
the TeleMini with new firmware, showing a progress bar.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Confirm that the TeleMini board seems to have updated OK, which you
can do by configuring it over the radio link through the TeleDongle, or
letting it come up in "flight" mode and listening for telemetry.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
If something goes wrong, give it another try.
- </listitem>
+ </para>
+</listitem>
</orderedlist>
</section>
<section>
</para>
<orderedlist inheritnum='inherit' numeration='arabic'>
<listitem>
+<para>
Find the 'programming cable' that you got as part of the starter
kit, that has a red 8-pin MicroMaTch connector on one end and a
red 4-pin MicroMaTch connector on the other end.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Find the USB cable that you got as part of the starter kit, and
plug the "mini" end in to the mating connector on TeleMetrum or TeleDongle.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Take the 2 screws out of the TeleDongle case to get access
to the circuit board.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Plug the 8-pin end of the programming cable to the
matching connector on the programmer, and the 4-pin end to the
matching connector on the TeleDongle.
Note that each MicroMaTch connector has an alignment pin that
goes through a hole in the PC board when you have the cable
oriented correctly.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Attach a battery to the TeleMetrum board if you're using one.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Plug both the programmer and the TeleDongle into your computer's USB
ports, and power up the programmer.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Run AltosUI, and select 'Flash Image' from the File menu.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Pick the programmer device from the list, identifying it as the
programming device.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Select the image you want put on the TeleDongle, which should have a
name in the form teledongle-v0.2-1.0.0.ihx. It should be visible
in the default directory, if not you may have to poke around
your system to find it.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Make sure the configuration parameters are reasonable
looking. If the serial number and/or RF configuration
values aren't right, you'll need to change them. The TeleDongle
serial number is on the "bottom" of the circuit board, and can
usually be read through the translucent blue plastic case without
needing to remove the board from the case.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Hit the 'OK' button and the software should proceed to flash
the TeleDongle with new firmware, showing a progress bar.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
Confirm that the TeleDongle board seems to have updated OK, which you
can do by plugging in to it over USB and using a terminal program
to connect to the board and issue the 'v' command to check
the version, etc. Once you're happy, remove the programming cable
and put the cover back on the TeleDongle.
- </listitem>
+ </para>
+</listitem>
<listitem>
+<para>
If something goes wrong, give it another try.
- </listitem>
+ </para>
+</listitem>
</orderedlist>
<para>
Be careful removing the programming cable from the locking 8-pin
</listitem>
<listitem>
<para>
- RF interface for battery charging, configuration, and data recovery.
+ RF interface for configuration, and data recovery.
</para>
</listitem>
<listitem>
once you enable the voice output!
</para>
</appendix>
+ <appendix>
+ <title>Drill Templates</title>
+ <para>
+ These images, when printed, provide precise templates for the
+ mounting holes in Altus Metrum flight computers
+ </para>
+ <section>
+ <title>TeleMetrum template</title>
+ <para>
+ TeleMetrum has overall dimensions of 1.000 x 2.750 inches, and the
+ mounting holes are sized for use with 4-40 or M3 screws.
+ </para>
+ <mediaobject id="TeleMetrumTemplate">
+ <imageobject>
+ <imagedata format="SVG" fileref="telemetrum.svg"/>
+ </imageobject>
+ </mediaobject>
+ </section>
+ <section>
+ <title>TeleMini template</title>
+ <para>
+ TeleMini has overall dimensions of 0.500 x 1.500 inches, and the
+ mounting holes are sized for use with 2-56 or M2 screws.
+ </para>
+ <mediaobject id="TeleMiniTemplate">
+ <imageobject>
+ <imagedata format="SVG" fileref="telemini.svg"/>
+ </imageobject>
+ </mediaobject>
+ </section>
+ </appendix>
<appendix>
<title>Calibration</title>
<para>
</para>
</section>
</appendix>
- <appendix
- xmlns:xi="http://www.w3.org/2001/XInclude">
+ <appendix>
<title>Release Notes</title>
- <xi:include href="release-notes-1.1.xsl" xpointer="xpointer(/article/*)"/>
- <xi:include href="release-notes-1.0.1.xsl" xpointer="xpointer(/article/*)"/>
- <xi:include href="release-notes-0.9.2.xsl" xpointer="xpointer(/article/*)"/>
- <xi:include href="release-notes-0.9.xsl" xpointer="xpointer(/article/*)"/>
- <xi:include href="release-notes-0.8.xsl" xpointer="xpointer(/article/*)"/>
- <xi:include href="release-notes-0.7.1.xsl" xpointer="xpointer(/article/*)"/>
+ <simplesect>
+ <title>Version 1.3</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.3.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.2.1</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.2.1.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.2</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.2.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.1.1</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.1.1.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.1</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.1.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 1.0.1</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.0.1.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 0.9.2</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-0.9.2.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 0.9</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-0.9.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 0.8</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-0.8.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
+ <simplesect>
+ <title>Version 0.7.1</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-0.7.1.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
</appendix>
</book>
-<!-- LocalWords: Altusmetrum
--->
+<!-- LocalWords: Altusmetrum
+-->
\ No newline at end of file
projects / fw / altos / blobdiff