[debian/amanda] / example / amanda.conf.in

# amanda.conf - sample Amanda configuration file. See amanda.conf(5) for 
# details

org      "@DEFAULT_CONFIG@"     # your organization name for reports
mailto   "@CLIENT_LOGIN@"       # space separated list of operators at your site
dumpuser "@CLIENT_LOGIN@"       # the user to run dumps under

inparallel 4            # maximum dumpers that will run in parallel (max 63)
                        # this maximum can be increased at compile-time,
                        # modifying MAX_DUMPERS in server-src/driverio.h
dumporder "sssS"        # specify the priority order of each dumper
                        #   s -> smallest size
                        #   S -> biggest size
                        #   t -> smallest time
                        #   T -> biggest time
                        #   b -> smallest bandwitdh
                        #   B -> biggest bandwitdh
                        # try "BTBTBTBTBTBT" if you are not holding
                        # disk constrained

taperalgo first         # The algorithm used to choose which dump image to send
                        # to the taper.
                        # Possible values: 
                        # [first|firstfit|largest|largestfit|smallest|last]
                        # Default: first. 
                        # first         First in - first out.
                        # firstfit      The first dump image that will fit 
                        #               on the current tape.
                        # largest       The largest dump image.
                        # largestfit    The largest dump image that will fit 
                        #               on the current tape.
                        # smallest      The smallest dump image.
                        # last          Last in - first out.

displayunit "k"         # Possible values: "k|m|g|t"
                        # Default: k. 
                        # The unit used to print many numbers.
                        # k=kilo, m=mega, g=giga, t=tera
                        
netusage  8000 Kbps     # maximum net bandwidth for Amanda, in KB per sec

dumpcycle 4 weeks       # the number of days in the normal dump cycle
runspercycle 20         # the number of amdump runs in dumpcycle days
                        # (4 weeks * 5 amdump runs per week -- just weekdays)
tapecycle 25 tapes      # the number of tapes in rotation
                        # 4 weeks (dumpcycle) times 5 tapes per week (just
                        # the weekdays) plus a few to handle errors that
                        # need amflush and so we do not overwrite the full
                        # backups performed at the beginning of the previous
                        # cycle

bumpsize 20 Mb          # minimum savings (threshold) to bump level 1 -> 2
bumppercent 20          # minimum savings (threshold) to bump level 1 -> 2
bumpdays 1              # minimum days at each level
bumpmult 4              # threshold = bumpsize * bumpmult^(level-1)

etimeout 300            # number of seconds per filesystem for estimates.
dtimeout 1800           # number of idle seconds before a dump is aborted.
ctimeout 30             # maximum number of seconds that amcheck waits
                        # for each client host
 
device_output_buffer_size 1280k
                        # amount of buffer space to use when writing to devices

# By default, Amanda can only track at most one run per calendar day. When
# the usetimestamps option is enabled, however, Amanda can track as many
# runs as you care to make.
# WARNING: This option is not backward-compatible. Do not enable it if you
#          intend to downgrade your server installation to Amanda community 
#          edition 2.5
usetimestamps yes

# flush-threshold-dumped, flush-threshold-scheduled, taperflush, and autoflush
# are used to control tape utilization. See the amanda.conf (5) manpage for
# details on how they work. Taping will not start until all criteria are
# satisfied. Here are some examples:
#
# You want to fill tapes completely even in the case of failed dumps, and
# don't care if some dumps are left on the holding disk after a run:
# flush-threshold-dumped        100 # (or more)
# flush-threshold-scheduled     100 # (or more)
# taperflush                    100
# autoflush                     yes
#
# You want to improve tape performance by waiting for a complete tape of data
# before writing anything. However, all dumps will be flushed; none will
# be left on the holding disk.
# flush-threshold-dumped        100 # (or more)
# flush-threshold-scheduled     100 # (or more)
# taperflush    0
#
# You don't want to use a new tape for every run, but want to start writing
# to tape as soon as possible:
# flush-threshold-dumped        0   # (or more)
# flush-threshold-scheduled     100 # (or more)
# taperflush    100
# autoflush     yes
# maxdumpsize   100k # amount of data to dump each run; see above.
#
# You want to keep the most recent dumps on holding disk, for faster recovery.
# Older dumps will be rotated to tape during each run.
# flush-threshold-dumped        300 # (or more)
# flush-threshold-scheduled     300 # (or more)
# taperflush    300
# autoflush     yes
#
# Defaults:
# (no restrictions; flush to tape immediately; don't flush old dumps.)
flush-threshold-dumped 0
flush-threshold-scheduled 0
taperflush 0
autoflush no

# Specify tape device or tape changer.

runtapes 1                      # number of tapes to be used in a single run of amdump
tapedev "@EXAMPLE_TAPEDEV@"     # tape changer or device to use

# To use vtapes, create some slotN directories (slot0, slot1, etc.) under
# /var/amanda/vtapes and use this tapedev:
## tapedev "chg-disk:/var/amanda/vtapes"

# To use a tape library, uncomment this definition.  See amanda-changers(7)
# for more configuration options.
#
# define changer myrobot {
#   tpchanger "chg-robot:/dev/sg0"  # your changer device file
#   tapedev "tape:@EXAMPLE_TAPEDEV@"    # your tape drive device file
# }
# tapedev "myrobot"

# If you want Amanda to automatically label any non-Amanda tapes it
# encounters, uncomment the line below. Note that this will ERASE any
# non-Amanda tapes you may have, and may also ERASE any near-failing tapes.
# Use with caution.
## label_new_tapes "@DEFAULT_CONFIG@-%%%"

maxdumpsize -1          # Maximum number of bytes the planner will schedule
                        # for a run (default: runtapes * tape_length).
tapetype HP-DAT         # what kind of tape it is (see tapetypes below)
labelstr "^@DEFAULT_CONFIG@-[0-9][0-9]*$"       # label constraint regex: all tapes must match

amrecover_do_fsf yes            # amrecover will call amrestore with the
                                # -f flag for faster positioning of the tape.
amrecover_check_label yes       # amrecover will call amrestore with the
                                # -l flag to check the label.
amrecover_changer "changer"     # amrecover will use the changer if you restore
    # from this device. It could be a string like 'changer' and amrecover will use your
    # changer if you set your tape to 'changer' with 'setdevice changer' or via 
    # 'tapedev "changer"' in amanda-client.conf

# Specify holding disks.  These are used as a temporary staging area for
# dumps before they are written to tape and are recommended for most sites.
# The advantages include: tape drive is more likely to operate in streaming
# mode (which reduces tape and drive wear, reduces total dump time); multiple
# dumps can be done in parallel (which can dramatically reduce total dump time.
# The main disadvantage is that dumps on the holding disk need to be flushed
# (with amflush) to tape after an operating system crash or a tape failure.
# If no holding disks are specified then all dumps will be written directly
# to tape.  If a dump is too big to fit on the holding disk than it will be
# written directly to tape.  If more than one holding disk is specified then
# they will all be used based on activity and available space.

holdingdisk hd1 {
    comment "main holding disk"
    directory "/dumps/amanda"   # where the holding disk is
    use -100 Mb                 # how much space can we use on it
                                # a non-positive value means:
                                # use all space but that value
    chunksize 1Gb       # size of chunk if you want big dump to be
                        # dumped on multiple files on holding disks
                        #  N Kb/Mb/Gb split images in chunks of size N
                        #             The maximum value should be
                        #             (MAX_FILE_SIZE - 1Mb)
                        #  0          same as INT_MAX bytes
    }
#holdingdisk hd2 {
#    directory "/dumps2/amanda"
#    use 1000 Mb
#    }
#holdingdisk hd3 {
#    directory "/mnt/disk4"
#    use 1000 Mb
#    }


# If amanda cannot find a tape on which to store backups, it will run
# as many backups as it can to the holding disks.  In order to save
# space for unattended backups, by default, amanda will only perform
# incremental backups in this case, i.e., it will reserve 100% of the
# holding disk space for the so-called degraded mode backups.
# However, if you specify a different value for the `reserve'
# parameter, amanda will not degrade backups if they will fit in the
# non-reserved portion of the holding disk.

# reserve 30 # percent
# This means save at least 30% of the holding disk space for degraded
# mode backups.  

# The format for a ColumnSpec is a ',' seperated list of triples.
# Each triple consists of
#   + the name of the column (as in ColumnNameStrings)
#   + prefix before the column
#   + the width of the column, if set to -1 it will be recalculated
#     to the maximum length of a line to print.
# Example:
#       "Disk=1:17,HostName=1:10,OutKB=1:7"
# or
#       "Disk=1:-1,HostName=1:10,OutKB=1:7"
#        
# You need only specify those colums that should be changed from
# the default. If nothing is specified in the configfile, the
# above compiled in values will be in effect, resulting in an
# output as it was all the time.
# The names of the colums are:
# HostName, Disk, Level, OrigKB, OutKB, Compress, DumpTime, DumpRate,
# TapeTime and TapeRate.
#                                                       ElB, 1999-02-24.
# columnspec "Disk=1:18,HostName=0:10,OutKB=1:7"


# Amanda needs a few Mb of diskspace for the log and debug files,
# as well as a database.  This stuff can grow large, so the conf directory
# isn't usually appropriate.  Some sites use /usr/local/var and some /usr/adm.
# Create an amanda directory under there.  You need a separate infofile and
# logdir for each configuration, so create subdirectories for each conf and
# put the files there.  Specify the locations below.

# Note that, although the keyword below is infofile, it is only so for
# historic reasons, since now it is supposed to be a directory (unless
# you have selected some database format other than the `text' default)
infofile "@CONFIG_DIR@/@DEFAULT_CONFIG@/curinfo"        # database DIRECTORY
logdir   "@CONFIG_DIR@/@DEFAULT_CONFIG@"                # log directory
indexdir "@CONFIG_DIR@/@DEFAULT_CONFIG@/index"          # index directory
#tapelist "@CONFIG_DIR@/@DEFAULT_CONFIG@/tapelist"      # list of used tapes
# tapelist is stored, by default, in the directory that contains amanda.conf

# tapetypes

# Define the type of tape you use here, and use it in "tapetype"
# above.  Some typical types of tapes are included here.  The tapetype
# tells amanda how many MB will fit on the tape, how big the filemarks
# are, and how fast the tape device is.

# A filemark is the amount of wasted space every time a tape section
# ends.

# For completeness Amanda should calculate the inter-record gaps too,
# but it doesn't.  For EXABYTE and DAT tapes this is ok.  Anyone using
# 9 tracks for amanda and need IRG calculations?  Drop me a note if
# so.

# If you want amanda to print postscript paper tape labels
# add a line after the comment in the tapetype of the form
#    lbl-templ "/path/to/postscript/template/label.ps"

# if you want the label to go to a printer other than the default
# for your system, you can also add a line above for a different
# printer. (i usually add that line after the dumpuser specification)

# dumpuser "operator"     # the user to run dumps under
# printer "mypostscript"  # printer to print paper label on

# here is an example of my definition for an EXB-8500

# define tapetype EXB-8500 {
# ...
#     lbl-templ "@CONFIG_DIR@/config/lbl.exabyte.ps"
# }


define tapetype QIC-60 {
    comment "Archive Viper"
    length 60 mbytes
    filemark 100 kbytes         # don't know a better value
    speed 100 kbytes            # dito
}

define tapetype DEC-DLT2000 {
    comment "DEC Differential Digital Linear Tape 2000"
    length 15000 mbytes
    filemark 8 kbytes
    speed 1250 kbytes
}

# goluboff@butch.Colorado.EDU
# in amanda-users (Thu Dec 26 01:55:38 MEZ 1996)
define tapetype DLT {
    comment "DLT tape drives"
    length 20000 mbytes         # 20 Gig tapes
    filemark 2000 kbytes        # I don't know what this means
    speed 1536 kbytes           # 1.5 Mb/s
}

define tapetype SURESTORE-1200E {
    comment "HP AutoLoader"
    length 3900 mbytes
    filemark 100 kbytes
    speed 500 kbytes
}

define tapetype EXB-8500 {
    comment "Exabyte EXB-8500 drive on decent machine"
    length 4200 mbytes
    filemark 48 kbytes
    speed 474 kbytes                    
}

define tapetype EXB-8200 {
    comment "Exabyte EXB-8200 drive on decent machine"
    length 2200 mbytes
    filemark 2130 kbytes
    speed 240 kbytes                    
}

define tapetype HP-DAT {
    comment "DAT tape drives"
    # data provided by Rob Browning <rlb@cs.utexas.edu>
    length 1930 mbytes
    filemark 111 kbytes
    speed 468 kbytes
}

define tapetype DAT {
    comment "DAT tape drives"
    length 1000 mbytes          # these numbers are not accurate
    filemark 100 kbytes         # but you get the idea
    speed 100 kbytes
}

define tapetype MIMSY-MEGATAPE {
    comment "Megatape (Exabyte based) drive through Emulex on Vax 8600"
    length 2200 mbytes
    filemark 2130 kbytes
    speed 170 kbytes            # limited by the Emulex bus interface, ugh
}

define tapetype SEAGATE-ULTRIUM-LTO {
     comment "SEAGATE ULTRIUM 06242 LTO, compression off"
     length 99584 mbytes
     filemark 0 kbytes
     speed 11288 kps
}

# dumptypes
#
# These are referred to by the disklist file.  The dumptype specifies
# certain parameters for dumping including:
#   auth        - authentication scheme to use between server and client.
#                 Valid values are "bsd", "bsdudp", "bsdtcp", "krb5", "local",
#                 "rsh" and "ssh".  
#                 Default: [auth "bsd"]
#   comment     - just a comment string
#   comprate    - set default compression rate.  Should be followed by one or
#                 two numbers, optionally separated by a comma.  The 1st is
#                 the full compression rate; the 2nd is the incremental rate.
#                 If the second is omitted, it is assumed equal to the first.
#                 The numbers represent the amount of the original file the
#                 compressed file is expected to take up.
#                 Default: [comprate 0.50, 0.50]
#   compress    - specify compression of the backed up data.  Valid values are:
#                 "none"        - don't compress the dump output.
#                 "client best" - compress on the client using the best (and
#                                 probably slowest) algorithm.
#                 "client fast" - compress on the client using fast algorithm.
#                 "client custom" - compress using your custom client compression program.
#                                   use client_custom_compress "PROG" to specify
#                                   the custom compression program.
#                                   PROG must not contain white space.
#                 "server best" - compress on the tape host using the best (and
#                                 probably slowest) algorithm.
#                 "server fast" - compress on the tape host using a fast
#                                 algorithm.  This may be useful when a fast
#                                 tape host is backing up slow clients.
#                 "server custom" - compress using your server custom compression program.
#                                   use server_custom_compress "PROG" to specify
#                                   the custom compression program.
#                                   PROG must not contain white space.
#                 Default: [compress client fast]
#   dumpcycle   - set the number of days in the dump cycle, ie, set how often a
#                 full dump should be performed.  Default: from DUMPCYCLE above
#   estimate      Determine the way AMANDA does it's estimate. 
#                 "client"      - Use the same program as the dumping program,
#                               this is the most accurate way to do estimates, 
#                               but it can take a long time.
#                 "calcsize"    - Use a faster program to do estimates, but the
#                               result is less accurate.
#                 "server"      - Use only statistics from the previous run to 
#                               give an estimate, 
#                               it takes only a few seconds but the result is not 
#                               accurate if your disk usage changes from day to day.
#                 Default: [client]
#   encrypt  - specify encryption of the backed up data. Valid values are:
#                 "none"   - don't encrypt the dump output.
#                 "client" - encrypt on the client using the program specified by 
#                            client_encrypt "PROG".
#                            Use client_decrypt_option to specify the decrypt- 
#                            parameter, default is "-d".
#                            PROG and decrypt-parameter must not contain white space.     
#                 "server" - encrypt on the server using the program specified by 
#                            server_encrypt "PROG".
#                            Use server_decrypt_option to specify the decrypt- 
#                            parameter, default is "-d".
#                            PROG and decrypt-parameter must not contain white space.
#                 Default: [none]
#   exclude     - specify files and directories to be excluded from the dump.
#                 Useful with gnutar only; silently ignored by dump and samba.
#                 Valid values are:
#                 "pattern"       - a shell glob pattern defining which files
#                                   to exclude.
#                                   gnutar gets --exclude="pattern"
#                 list "filename" - a file (on the client!) containing patterns
#                                   re's (1 per line) defining which files to
#                                   exclude.
#                                   gnutar gets --exclude-from="filename"
#                 Note that the `full pathname' of a file within its
#                 filesystem starts with `./', because of the way amanda runs
#                 gnutar: `tar -C $mountpoint -cf - --lots-of-options .' (note
#                 the final dot!)  Thus, if you're backing up `/usr' with a
#                 diskfile entry like ``host /usr gnutar-root', but you don't
#                 want to backup /usr/tmp, your exclude list should contain
#                 the pattern `./tmp', as this is relative to the `/usr' above.
#                 Please refer to the man-page of gnutar for more information.
#                 If a relative pathname is specified as the exclude list,
#                 it is searched from within the directory that is
#                 going to be backed up.
#                 Default: include all files
#   holdingdisk - should the holding disk be used for this dump.  Useful for
#                 dumping the holding disk itself.  Default: [holdingdisk auto]
#                 "never"    - Never use the holding disk.
#                 "auto"     - Use the holding disk if possible.
#                 "required" - Always use the holding disk.
#   ignore      - do not back this filesystem up.  Useful for sharing a single
#                 disklist in several configurations.
#   index       - keep an index of the files backed up.  Default: [index no]
#   kencrypt    - encrypt the data stream between the client and server.
#                 Default: [kencrypt no]
#   maxdumps    - max number of concurrent dumps to run on the client.
#                 Default: [maxdumps 1]
#   maxpromoteday - max number of day for a promotion, set it 0 if you don't
#                 want promotion, set it to 1 or 2 if your disk get
#                 overpromoted.
#                 Default: [10000]
#   priority    - priority level of the dump.  Valid levels are "low", "medium"
#                 or "high".  These are really only used when Amanda has no
#                 tape to write to because of some error.  In that "degraded
#                 mode", as many incrementals as will fit on the holding disk
#                 are done, higher priority first, to insure the important
#                 disks are at least dumped.  Default: [priority medium]
#   program     - specify the dump system to use.  Valid values are "DUMP",
#                 or "GNUTAR".  Default: [program "DUMP"].
#   record      - record the backup in the time-stamp-database of the backup
#                 program (e.g. /etc/dumpdates for DUMP or
#                 @GNUTAR_LISTED_INCREMENTAL_DIRX@ for GNUTAR.).
#                 Default: [record yes]
#   skip-full   - skip the disk when a level 0 is due, to allow full backups
#                 outside Amanda, eg when the machine is in single-user mode.
#   skip-incr   - skip the disk when the level 0 is NOT due.  This is used in
#                 archive configurations, where only full dumps are done and
#                 the tapes saved.
#   starttime   - delay the start of the dump?  Default: no delay
#   strategy    - set the dump strategy.  Valid strategies are currently:
#                 "standard" - the standard one.
#                 "nofull"   - do level 1 dumps every time.  This can be used,
#                              for example, for small root filesystems that
#                              only change slightly relative to a site-wide
#                              prototype.  Amanda then backs up just the
#                              changes.
#                 "noinc"    - do level 0 dumps every time.
#                 "skip"     - skip all dumps.  Useful for sharing a single
#                              disklist in several configurations.
#                 "incronly" - do only incremental dumps. This is similar
#                              to strategy 'nofull', but will increase
#                              the dump level as usual. Full dumps will
#                              only be performed when an 'amadmin force' 
#                              has been issued 
#                 Default: [strategy standard]
# tape_splitsize - (optional) split dump file into pieces of a specified size.
#                 This allows dumps to be spread across multiple tapes, and can
#                 potentially make more efficient use of tape space.  Note that
#                 if this value is too large (more than half the size of the
#                 average dump being split), substantial tape space can be
#                 wasted.  If too small, large dumps will be split into
#                 innumerable tiny dumpfiles, adding to restoration complexity.
#                 A good rule of thumb, usually, is 1/10 of the size of your
#                 tape.  Default: [disabled]
# split_diskbuffer - (optional) When dumping a split dump  in  PORT-WRITE
#                 mode (usually meaning "no holding disk"), buffer the split
#                 chunks to a file in the directory specified by this option.
#                 Default: [none]
# fallback_splitsize - (optional) When dumping a split dump  in  PORT-WRITE
#                 mode, if no split_diskbuffer is specified (or if we somehow
#                 fail to use our split_diskbuffer), we must buffer split
#                 chunks in memory.  This specifies the maximum size split
#                 chunks can be in this scenario, and thus the maximum amount
#                 of memory consumed for in-memory splitting.  Default: [10m]
#
# Note that you may specify previously defined dumptypes as a shorthand way of
# defining parameters.

define dumptype global {
    comment "Global definitions"
    # This is quite useful for setting global parameters, so you don't have
    # to type them everywhere.  All dumptype definitions in this sample file
    # do include these definitions, either directly or indirectly.
    # There's nothing special about the name `global'; if you create any
    # dumptype that does not contain the word `global' or the name of any
    # other dumptype that contains it, these definitions won't apply.
    # Note that these definitions may be overridden in other
    # dumptypes, if the redefinitions appear *after* the `global'
    # dumptype name.
    # You may want to use this for globally enabling or disabling
    # indexing, recording, etc.  Some examples:
    # index yes
    # record no
    # split_diskbuffer "/raid/amanda"
    # fallback_splitsize 64m
}

define dumptype always-full {
    global
    comment "Full dump of this filesystem always"
    compress none
    priority high
    dumpcycle 0
}

# Dumptypes for gnutar
define dumptype root-tar {
    global
    program "GNUTAR"
    comment "root partitions dumped with tar"
    compress none
    index
#   exclude list "@CONFIG_DIR@/exclude.gtar"
    priority low
}

define dumptype user-tar {
    root-tar
    comment "user partitions dumped with tar"
    priority medium
}

define dumptype user-tar-span {
    root-tar
    tape_splitsize 3 Gb
    comment "tape-spanning user partitions dumped with tar"
    priority medium
}

define dumptype high-tar {
    root-tar
    comment "partitions dumped with tar"
    priority high
}

define dumptype comp-root-tar {
    root-tar
    comment "Root partitions with compression"
    compress client fast
}

define dumptype comp-user-tar {
    user-tar
    compress client fast
}

define dumptype comp-user-tar-span {
    user-tar-span
    compress client fast
}

define dumptype holding-disk {
    global
    comment "The master-host holding disk itself"
    holdingdisk never # do not use the holding disk
    priority medium
}

define dumptype comp-user {
    global
    comment "Non-root partitions on reasonably fast machines"
    compress client fast
    priority medium
}

define dumptype comp-user-span {
    global
    tape_splitsize 5 Gb
    comment "Tape-spanning non-root partitions on reasonably fast machines"
    compress client fast
    priority medium
}

define dumptype nocomp-user {
    comp-user
    comment "Non-root partitions on slow machines"
    compress none
}

define dumptype nocomp-user-span {
    comp-user-span
    comment "Tape-spanning non-root partitions on slow machines"
    compress none
}

define dumptype comp-root {
    global
    comment "Root partitions with compression"
    compress client fast
    priority low
}

define dumptype nocomp-root {
    comp-root
    comment "Root partitions without compression"
    compress none
}

define dumptype comp-high {
    global
    comment "very important partitions on fast machines"
    compress client best
    priority high
}

define dumptype nocomp-high {
    comp-high
    comment "very important partitions on slow machines"
    compress none
}

define dumptype nocomp-test {
    global
    comment "test dump without compression, no /etc/dumpdates recording"
    compress none
    record no
    priority medium
}

define dumptype comp-test {
    nocomp-test
    comment "test dump with compression, no /etc/dumpdates recording"
    compress client fast
}

define dumptype custom-compress {
   global
   program "GNUTAR"
   comment "custom client compression dumped with tar"
   compress client custom
   client_custom_compress "/usr/bin/bzip2"
}

define dumptype server-encrypt-fast {
   global
   program "GNUTAR"
   comment "fast client compression and server symmetric encryption"
   compress client fast
   encrypt server
   server_encrypt "/usr/sbin/amcrypt"
   server_decrypt_option "-d"
}

define dumptype client-encrypt-nocomp {
   global
   program "GNUTAR"
   comment "no compression and client symmetric encryption"
   compress none
   encrypt client
   client_encrypt "/usr/sbin/amcrypt"
   client_decrypt_option "-d"
}


# To use gpg public-key encryption, gpg does compress with zlib by default.
# Thus, no need to specify compress

#define dumptype gpg-encrypt {
#    global
#    program "GNUTAR"
#    comment "server public-key encryption, dumped with tar"
#    compress none
#    encrypt server
#    server_encrypt "/usr/sbin/amgpgcrypt"
#    server_decrypt_option "-d"
#}


# network interfaces
#
# These are referred to by the disklist file.  They define the attributes
# of the network interface that the remote machine is accessed through.
# Notes: - netusage above defines the attributes that are used when the
#          disklist entry doesn't specify otherwise.
#        - the values below are only samples.
#        - specifying an interface does not force the traffic to pass
#          through that interface.  Your OS routing tables do that.  This
#          is just a mechanism to stop Amanda trashing your network.
# Attributes are:
#       use             - bandwidth above which amanda won't start
#                         backups using this interface.  Note that if
#                         a single backup will take more than that,
#                         amanda won't try to make it run slower!

define interface local {
    comment "a local disk"
    use 8000 kbps
}

#define interface le0 {
#    comment "10 Mbps ethernet"
#    use 400 kbps
#}

#define application-tool and dumptype for the amgtar application
define application-tool app_amgtar {
    comment "amgtar"
    plugin  "amgtar"
    #property "GNUTAR-PATH" "/path/to/gtar"
    #property "GNUTAR-LISTDIR" "/path/to/gnutar_list_dir"
                    #default from gnutar_list_dir setting in amanda-client.conf
}

define dumptype dt_amgtar {
    program "APPLICATION"
    application "app_amgtar"
}

#define application-tool and dumptype for the amstar application
define application-tool app_amstar {
    comment "amstar"
    plugin  "amstar"
    #property "STAR-PATH" "/path/to/star"
    #property "STAR-TARDUMP" "/path/to/tardumps"  # default /etc/tardumps
    #property "STAR-DLE-TARDUMP" "no"
        # if 'yes' then create a different tardump file for each DLE,
        # it is required if you do many dump in parallel (maxdump>1)
}

define dumptype dt_amstar {
    program "APPLICATION"
    application "app_amstar"
}

#define a script-tool to send an email
define script-tool sc-email {
  comment "script-email"
  plugin  "script-email"
  execute_on pre-dle-amcheck, pre-host-amcheck, post-dle-amcheck, post-host-amcheck, pre-dle-estimate, pre-host-estimate, post-dle-estimate, post-host-estimate, pre-dle-backup, pre-host-backup, post-dle-backup, post-host-backup
  execute_where server                  # or client
  property "mailto" "martinea"
}
#your dumptype must include: script "sc-email"
#to use the script

# You may include other amanda configuration files, so you can share
# dumptypes, tapetypes and interface definitions among several
# configurations.

#includefile "@CONFIG_DIR@/amanda.conf.main"