summary |
shortlog |
log |
commit | commitdiff |
tree
raw |
patch |
inline | side by side (from parent 1:
410af11)
1. Use correct quotes.
2. Eliminate double space after punctuation.
3. Use elipses instead of three full stops.
Signed-off-by: Keith Packard <keithp@keithp.com>
=== Changing the Configuration
All available configuration options can be set using the
=== Changing the Configuration
All available configuration options can be set using the
- "Configure Altimeter" menu selection within the AltosUI
+ “Configure Altimeter” menu selection within the AltosUI
EasyMotor needs to be rigidly attached in the airframe, and the
long axis of the circuit board needs to be aligned with the axis
EasyMotor needs to be rigidly attached in the airframe, and the
long axis of the circuit board needs to be aligned with the axis
- of flight. By default, the round beeper on the board should be
- "up" towards the nose cone, and the screw terminal strips should
- be "down" towards the fins and motor nozzle end of the rocket.
+ of flight. By default, the round beeper on the board should be
+ “up” towards the nose cone, and the screw terminal strips should
+ be “down” towards the fins and motor nozzle end of the rocket.
=== Power Switch and Battery
=== Power Switch and Battery
- In addition to the circuit board itself, EasyMotor needs
- a power switch and battery to operate. Unlike most other
- Altus Metrum products, EasyMotor does not work with
- single-cell LiPo batteries. That's because commonly
+ In addition to the circuit board itself, EasyMotor needs
+ a power switch and battery to operate. Unlike most other
+ Altus Metrum products, EasyMotor does not work with
+ single-cell LiPo batteries. That's because commonly
available inexpensive pressure sensors need 5V, which is
available inexpensive pressure sensors need 5V, which is
- more than a single-cell LiPo provides. Any battery that
- provides from 6.5 to about 15 volts should work. Good
- choices are the common 9V alkaline battery, or the very
+ more than a single-cell LiPo provides. Any battery that
+ provides from 6.5 to about 15 volts should work. Good
+ choices are the common 9V alkaline battery, or the very
small and light A23 12V alkaline batteries.
small and light A23 12V alkaline batteries.
- Because he often mounts EasyMotor to the motor's forward
- bulkhead instead of to the airframe itself, Bdale often
- uses a length of "shooter wire" from an e-match or used
- motor igniter as a power switch, routing the wire out of
- the typical fin can vent hole and using "twist and tape"
- to power up the board. Whatever works!
+ Because he often mounts EasyMotor to the motor's forward
+ bulkhead instead of to the airframe itself, Bdale often
+ uses a length of “shooter wire” from an e-match or used
+ motor igniter as a power switch, routing the wire out of
+ the typical fin can vent hole and using “twist and tape”
+ to power up the board. Whatever works!
=== Pressure Sensor
The primary motivation for designing EasyMotor was to have
a reliable way of recording motor chamber pressure during
=== Pressure Sensor
The primary motivation for designing EasyMotor was to have
a reliable way of recording motor chamber pressure during
- flight. To that end, EasyMotor supports attachment of a
- low-cost analog pressure sensor. The board provides 5V
- to power the sensor, and an input for measuring and
+ flight. To that end, EasyMotor supports attachment of a
+ low-cost analog pressure sensor. The board provides 5V
+ to power the sensor, and an input for measuring and
logging the output voltage from the sensor.
The kind of sensor EasyMotor is designed to work with
takes 5V in and has a linear analog output that ranges
from 0.5V at 0 to 4.5V at the maximum pressure supported
logging the output voltage from the sensor.
The kind of sensor EasyMotor is designed to work with
takes 5V in and has a linear analog output that ranges
from 0.5V at 0 to 4.5V at the maximum pressure supported
- by the sensor. Very inexpensive sensors that have a
- "1/8 NPT" threaded input, a "Buick-style" 3-pin connector,
- and typically ship with a short cable and mating
+ by the sensor. Very inexpensive sensors that have a
+ “1/8 NPT” threaded input, a “Buick-style” 3-pin connector,
+ and typically ship with a short cable and mating
connector, are readily available on eBay and AliExpress.
To log in-flight chamber pressure, a typical approach
connector, are readily available on eBay and AliExpress.
To log in-flight chamber pressure, a typical approach
- might be to drill a 1/8" sampling hole all the way
+ might be to drill a 1/8" sampling hole all the way
through the center of the motor's forward closure, then
through the center of the motor's forward closure, then
- drill and tap partially through the closure with a "1/8
- NPT" pipe tap. Fill the touch hole with grease, screw in
- the pressure sensor, and attach the sensor leads to
+ drill and tap partially through the closure with a “1/8
+ NPT” pipe tap. Fill the touch hole with grease, screw in
+ the pressure sensor, and attach the sensor leads to
== Introduction and Overview
== Introduction and Overview
-Welcome to the Altus Metrum community! Our circuits and software reflect
-our passion for both hobby rocketry and Free Software. We hope their
+Welcome to the Altus Metrum community! Our circuits and software reflect
+our passion for both hobby rocketry and Free Software. We hope their
capabilities and performance will delight you in every way, but by
releasing all of our hardware and software designs under open licenses,
we also hope to empower you to take as active a role in our collective
capabilities and performance will delight you in every way, but by
releasing all of our hardware and software designs under open licenses,
we also hope to empower you to take as active a role in our collective
Thank you for your interest in motor testing products from Altus Metrum.
Our first such product is EasyMotor, an in-flight motor data collection
Thank you for your interest in motor testing products from Altus Metrum.
Our first such product is EasyMotor, an in-flight motor data collection
-board for hobby rockets. EasyMotor is a small circuit board that is meant
-to log motor chamber pressure and rocket acceleration during flight. With
+board for hobby rockets. EasyMotor is a small circuit board that is meant
+to log motor chamber pressure and rocket acceleration during flight. With
this data it's possible to determine whether a research motor is performing
this data it's possible to determine whether a research motor is performing
-as expected. With additional information about masses and airframe drag,
+as expected. With additional information about masses and airframe drag,
it is even possible to closely estimate complete motor performance.
it is even possible to closely estimate complete motor performance.
-With EasyMotor, the dilemma of "do I burn this on a test stand to learn more
-about how it actually works, or do I go fly it" is no more! You can fly your
+With EasyMotor, the dilemma of “do I burn this on a test stand to learn more
+about how it actually works, or do I go fly it” is no more! You can fly your
motor and get real performance data about it too!
motor and get real performance data about it too!
-Because documentation is just as prone as software to contain "bugs", and
-can always be improved... If you have questions that aren't answered in this
+Because documentation is just as prone as software to contain “bugs”, and
+can always be improved… If you have questions that aren't answered in this
manual, or just need a little help figuring things out, we strongly suggest
joining the Altus Metrum user email list, which you can do by visiting
https://lists.gag.com/mailman/listinfo/altusmetrum.
manual, or just need a little help figuring things out, we strongly suggest
joining the Altus Metrum user email list, which you can do by visiting
https://lists.gag.com/mailman/listinfo/altusmetrum.
- Operating an EasyMotor board is pretty easy. Turn the power on
+ Operating an EasyMotor board is pretty easy. Turn the power on
before launch, typically during the usual pre-flight electronics
before launch, typically during the usual pre-flight electronics
- checklist after the rocket is installed on a launch rail.
+ checklist after the rocket is installed on a launch rail.
- The board will beep out a Morse code "P" every few seconds
+ The board will beep out a Morse code “P” every few seconds
indicating that it's in pad mode and ready to detect launch.
Once launch is detected, the board logs pressure and acceleration
data 100 times per second throughout the flight.
After flight, AltosUI can be used to download the flight data,
indicating that it's in pad mode and ready to detect launch.
Once launch is detected, the board logs pressure and acceleration
data 100 times per second throughout the flight.
After flight, AltosUI can be used to download the flight data,
- then export it to a comma separated values (CSV) file. Such a
+ then export it to a comma separated values (CSV) file. Such a
file can easily be loaded into a spreadsheet for analysis.
file can easily be loaded into a spreadsheet for analysis.