+++ /dev/null
-#!/bin/sh
-
-if [ -x ../ao-tools/ao-load/ao-load ]; then
- AOLOAD=../ao-tools/ao-load/ao-load
-elif [ -x /usr/bin/ao-load ]; then
- AOLOAD=/usr/bin/ao-load
-else
- echo "Can't find ao-load! Aborting."
- exit 1
-fi
-
-if [ -x ../ao-tools/ao-rawload/ao-rawload ]; then
- RAWLOAD=../ao-tools/ao-rawload/ao-rawload
-elif [ -x /usr/bin/ao-rawload ]; then
- RAWLOAD=/usr/bin/ao-rawload
-else
- echo "Can't find ao-rawload! Aborting."
- exit 1
-fi
-
-echo "TeleBT v1.1 Turn-On and Calibration Program"
-echo "Copyright 2013 by Bdale Garbee. Released under GPL v2"
-echo
-echo "Expectations:"
-echo "\tTeleBT v1.1 powered from USB"
-echo "\t\twith TeleDonlge (on /dev/ttyACM0) cabled to debug header"
-echo "\t\twith coax from SMA to frequency counter"
-echo
-echo -n "TeleBT serial number: "
-read SERIAL
-
-echo $RAWLOAD
-
-case $USER in
- bdale)
- DONGLE=100
- ;;
- keithp)
- DONGLE=186
- ;;
- *)
- echo "Unknow user"
- exit 1
- ;;
-esac
-
-$RAWLOAD -D $DONGLE -r ao_led_blink.ihx
-echo "LEDs should be blinking"
-sleep 5
-
-$RAWLOAD -D $DONGLE -r ao_radio_xmit.ihx
-echo -n "Generating RF carrier. Please enter measured frequency: "
-read FREQ
-
-CAL_VALUE=`nickle -e "floor(434.55 / $FREQ * 1186611 + 0.5)"`
-
-echo "Programming flash with cal value " $CAL_VALUE
-$AOLOAD -D $DONGLE --cal $CAL_VALUE ~/altusmetrumllc/Binaries/telebt-v1.0*.ihx $SERIAL
-
-echo "Serial number "$SERIAL" programmed with RF cal value "$CAL_VALUE
-echo $SERIAL","$CAL_VALUE >> cal_values
-echo "Unplug debug cable, power cycle, cu to the board, confirm freq and record power"
--- /dev/null
+#!/bin/sh
+
+if [ -x ../ao-tools/ao-load/ao-load ]; then
+ AOLOAD=../ao-tools/ao-load/ao-load
+elif [ -x /usr/bin/ao-load ]; then
+ AOLOAD=/usr/bin/ao-load
+else
+ echo "Can't find ao-load! Aborting."
+ exit 1
+fi
+
+if [ -x ../ao-tools/ao-rawload/ao-rawload ]; then
+ RAWLOAD=../ao-tools/ao-rawload/ao-rawload
+elif [ -x /usr/bin/ao-rawload ]; then
+ RAWLOAD=/usr/bin/ao-rawload
+else
+ echo "Can't find ao-rawload! Aborting."
+ exit 1
+fi
+
+echo "TeleBT v1.1 Turn-On and Calibration Program"
+echo "Copyright 2013 by Bdale Garbee. Released under GPL v2"
+echo
+echo "Expectations:"
+echo "\tTeleBT v1.1 powered from USB"
+echo "\t\twith TeleDonlge (on /dev/ttyACM0) cabled to debug header"
+echo "\t\twith coax from SMA to frequency counter"
+echo
+echo -n "TeleBT serial number: "
+read SERIAL
+
+echo $RAWLOAD
+
+case $USER in
+ bdale)
+ DONGLE=100
+ ;;
+ keithp)
+ DONGLE=186
+ ;;
+ *)
+ echo "Unknow user"
+ exit 1
+ ;;
+esac
+
+$RAWLOAD -D $DONGLE -r ao_led_blink.ihx
+echo "LEDs should be blinking"
+sleep 5
+
+$RAWLOAD -D $DONGLE -r ao_radio_xmit.ihx
+echo -n "Generating RF carrier. Please enter measured frequency: "
+read FREQ
+
+CAL_VALUE=`nickle -e "floor(434.55 / $FREQ * 1186611 + 0.5)"`
+
+echo "Programming flash with cal value " $CAL_VALUE
+$AOLOAD -D $DONGLE --cal $CAL_VALUE ~/altusmetrumllc/Binaries/telebt-v1.0*.ihx $SERIAL
+
+echo "Serial number "$SERIAL" programmed with RF cal value "$CAL_VALUE
+echo $SERIAL","$CAL_VALUE >> cal_values
+echo "Unplug debug cable, power cycle, cu to the board, confirm freq and record power"
from which you can download and install the application.
</para>
</section>
+ <section>
+ <title>Charging TeleBT Battery</title>
+ <para>
+ Before using TeleBT with AltosDroid, make sure the internal
+ TeleBT battery is charged. To do this, attach a micro USB
+ cable from a computer or other USB power source to TeleBT.
+ A dual LED on the circuit board should illuminate, showing
+ red while the battery is charging, green when charging is
+ completed, and both red and green on at the same time if
+ there is a battery fault.
+ </para>
+ </section>
<section>
<title>Connecting to TeleBT over Bluetoothâ„¢</title>
<para>