#include "arm_opcodes.h"
#include "arm_semihosting.h"
#include <helper/time_support.h>
+#include <rtt/rtt.h>
/* NOTE: most of this should work fine for the Cortex-M1 and
* Cortex-M0 cores too, although they're ARMv6-M not ARMv7-M.
uint32_t num, uint32_t value);
static void cortex_m_dwt_free(struct target *target);
-static int cortexm_dap_read_coreregister_u32(struct target *target,
- uint32_t *value, int regnum)
+static int cortex_m_load_core_reg_u32(struct target *target,
+ uint32_t regsel, uint32_t *value)
{
struct armv7m_common *armv7m = target_to_armv7m(target);
int retval;
return retval;
}
- retval = mem_ap_write_u32(armv7m->debug_ap, DCB_DCRSR, regnum);
+ retval = mem_ap_write_u32(armv7m->debug_ap, DCB_DCRSR, regsel);
if (retval != ERROR_OK)
return retval;
return retval;
}
-static int cortexm_dap_write_coreregister_u32(struct target *target,
- uint32_t value, int regnum)
+static int cortex_m_store_core_reg_u32(struct target *target,
+ uint32_t regsel, uint32_t value)
{
struct armv7m_common *armv7m = target_to_armv7m(target);
int retval;
if (retval != ERROR_OK)
return retval;
- retval = mem_ap_write_atomic_u32(armv7m->debug_ap, DCB_DCRSR, regnum | DCRSR_WnR);
+ retval = mem_ap_write_atomic_u32(armv7m->debug_ap, DCB_DCRSR, regsel | DCRSR_WnR);
if (retval != ERROR_OK)
return retval;
for (i = 0; i < num_regs; i++) {
r = &armv7m->arm.core_cache->reg_list[i];
- if (!r->valid)
+ if (r->exist && !r->valid)
arm->read_core_reg(target, r, i, ARM_MODE_ANY);
}
r = arm->cpsr;
xPSR = buf_get_u32(r->value, 0, 32);
- /* For IT instructions xPSR must be reloaded on resume and clear on debug exec */
- if (xPSR & 0xf00) {
- r->dirty = r->valid;
- cortex_m_store_core_reg_u32(target, 16, xPSR & ~0xff);
- }
-
/* Are we in an exception handler */
if (xPSR & 0x1FF) {
armv7m->exception_number = (xPSR & 0x1FF);
}
}
- /* REVISIT when S_SLEEP is set, it's in a Sleep or DeepSleep state.
- * How best to model low power modes?
- */
-
if (target->state == TARGET_UNKNOWN) {
- /* check if processor is retiring instructions */
- if (cortex_m->dcb_dhcsr & S_RETIRE_ST) {
+ /* check if processor is retiring instructions or sleeping */
+ if (cortex_m->dcb_dhcsr & S_RETIRE_ST || cortex_m->dcb_dhcsr & S_SLEEP) {
target->state = TARGET_RUNNING;
retval = ERROR_OK;
}
* in parallel with disabled interrupts can cause local faults
* to not be taken.
*
- * REVISIT this clearly breaks non-debug execution, since the
- * PRIMASK register state isn't saved/restored... workaround
- * by never resuming app code after debug execution.
+ * This breaks non-debug (application) execution if not
+ * called from armv7m_start_algorithm() which saves registers.
*/
buf_set_u32(r->value, 0, 1, 1);
r->dirty = true;
r->valid = true;
- /* Make sure we are in Thumb mode */
+ /* Make sure we are in Thumb mode, set xPSR.T bit */
+ /* armv7m_start_algorithm() initializes entire xPSR register.
+ * This duplicity handles the case when cortex_m_resume()
+ * is used with the debug_execution flag directly,
+ * not called through armv7m_start_algorithm().
+ */
r = armv7m->arm.cpsr;
buf_set_u32(r->value, 24, 1, 1);
r->dirty = true;
if (retval3 != ERROR_OK)
LOG_DEBUG("Ignoring AP write error right after reset");
- retval3 = dap_dp_init(armv7m->debug_ap->dap);
- if (retval3 != ERROR_OK)
+ retval3 = dap_dp_init_or_reconnect(armv7m->debug_ap->dap);
+ if (retval3 != ERROR_OK) {
LOG_ERROR("DP initialisation failed");
-
- else {
+ /* The error return value must not be propagated in this case.
+ * SYSRESETREQ or VECTRESET have been possibly triggered
+ * so reset processing should continue */
+ } else {
/* I do not know why this is necessary, but it
* fixes strange effects (step/resume cause NMI
* after reset) on LM3S6918 -- Michael Schwingen
if ((jtag_reset_config & RESET_HAS_SRST) &&
!(jtag_reset_config & RESET_SRST_NO_GATING) &&
target_was_examined(target)) {
- int retval = dap_dp_init(armv7m->debug_ap->dap);
+
+ int retval = dap_dp_init_or_reconnect(armv7m->debug_ap->dap);
if (retval != ERROR_OK) {
LOG_ERROR("DP initialisation failed");
return retval;
}
}
-static int cortex_m_load_core_reg_u32(struct target *target,
- uint32_t num, uint32_t *value)
-{
- int retval;
-
- /* NOTE: we "know" here that the register identifiers used
- * in the v7m header match the Cortex-M3 Debug Core Register
- * Selector values for R0..R15, xPSR, MSP, and PSP.
- */
- switch (num) {
- case 0 ... 18:
- /* read a normal core register */
- retval = cortexm_dap_read_coreregister_u32(target, value, num);
-
- if (retval != ERROR_OK) {
- LOG_ERROR("JTAG failure %i", retval);
- return ERROR_JTAG_DEVICE_ERROR;
- }
- LOG_DEBUG("load from core reg %i value 0x%" PRIx32 "", (int)num, *value);
- break;
-
- case ARMV7M_FPSCR:
- /* Floating-point Status and Registers */
- retval = target_write_u32(target, DCB_DCRSR, 0x21);
- if (retval != ERROR_OK)
- return retval;
- retval = target_read_u32(target, DCB_DCRDR, value);
- if (retval != ERROR_OK)
- return retval;
- LOG_DEBUG("load from FPSCR value 0x%" PRIx32, *value);
- break;
-
- case ARMV7M_S0 ... ARMV7M_S31:
- /* Floating-point Status and Registers */
- retval = target_write_u32(target, DCB_DCRSR, num - ARMV7M_S0 + 0x40);
- if (retval != ERROR_OK)
- return retval;
- retval = target_read_u32(target, DCB_DCRDR, value);
- if (retval != ERROR_OK)
- return retval;
- LOG_DEBUG("load from FPU reg S%d value 0x%" PRIx32,
- (int)(num - ARMV7M_S0), *value);
- break;
-
- case ARMV7M_PRIMASK:
- case ARMV7M_BASEPRI:
- case ARMV7M_FAULTMASK:
- case ARMV7M_CONTROL:
- /* Cortex-M3 packages these four registers as bitfields
- * in one Debug Core register. So say r0 and r2 docs;
- * it was removed from r1 docs, but still works.
- */
- cortexm_dap_read_coreregister_u32(target, value, 20);
-
- switch (num) {
- case ARMV7M_PRIMASK:
- *value = buf_get_u32((uint8_t *)value, 0, 1);
- break;
-
- case ARMV7M_BASEPRI:
- *value = buf_get_u32((uint8_t *)value, 8, 8);
- break;
-
- case ARMV7M_FAULTMASK:
- *value = buf_get_u32((uint8_t *)value, 16, 1);
- break;
-
- case ARMV7M_CONTROL:
- *value = buf_get_u32((uint8_t *)value, 24, 3);
- break;
- }
-
- LOG_DEBUG("load from special reg %i value 0x%" PRIx32 "", (int)num, *value);
- break;
-
- default:
- return ERROR_COMMAND_SYNTAX_ERROR;
- }
-
- return ERROR_OK;
-}
-
-static int cortex_m_store_core_reg_u32(struct target *target,
- uint32_t num, uint32_t value)
-{
- int retval;
- uint32_t reg;
- struct armv7m_common *armv7m = target_to_armv7m(target);
-
- /* NOTE: we "know" here that the register identifiers used
- * in the v7m header match the Cortex-M3 Debug Core Register
- * Selector values for R0..R15, xPSR, MSP, and PSP.
- */
- switch (num) {
- case 0 ... 18:
- retval = cortexm_dap_write_coreregister_u32(target, value, num);
- if (retval != ERROR_OK) {
- struct reg *r;
-
- LOG_ERROR("JTAG failure");
- r = armv7m->arm.core_cache->reg_list + num;
- r->dirty = r->valid;
- return ERROR_JTAG_DEVICE_ERROR;
- }
- LOG_DEBUG("write core reg %i value 0x%" PRIx32 "", (int)num, value);
- break;
-
- case ARMV7M_FPSCR:
- /* Floating-point Status and Registers */
- retval = target_write_u32(target, DCB_DCRDR, value);
- if (retval != ERROR_OK)
- return retval;
- retval = target_write_u32(target, DCB_DCRSR, 0x21 | (1<<16));
- if (retval != ERROR_OK)
- return retval;
- LOG_DEBUG("write FPSCR value 0x%" PRIx32, value);
- break;
-
- case ARMV7M_S0 ... ARMV7M_S31:
- /* Floating-point Status and Registers */
- retval = target_write_u32(target, DCB_DCRDR, value);
- if (retval != ERROR_OK)
- return retval;
- retval = target_write_u32(target, DCB_DCRSR, (num - ARMV7M_S0 + 0x40) | (1<<16));
- if (retval != ERROR_OK)
- return retval;
- LOG_DEBUG("write FPU reg S%d value 0x%" PRIx32,
- (int)(num - ARMV7M_S0), value);
- break;
-
- case ARMV7M_PRIMASK:
- case ARMV7M_BASEPRI:
- case ARMV7M_FAULTMASK:
- case ARMV7M_CONTROL:
- /* Cortex-M3 packages these four registers as bitfields
- * in one Debug Core register. So say r0 and r2 docs;
- * it was removed from r1 docs, but still works.
- */
- cortexm_dap_read_coreregister_u32(target, ®, 20);
-
- switch (num) {
- case ARMV7M_PRIMASK:
- buf_set_u32((uint8_t *)®, 0, 1, value);
- break;
-
- case ARMV7M_BASEPRI:
- buf_set_u32((uint8_t *)®, 8, 8, value);
- break;
-
- case ARMV7M_FAULTMASK:
- buf_set_u32((uint8_t *)®, 16, 1, value);
- break;
-
- case ARMV7M_CONTROL:
- buf_set_u32((uint8_t *)®, 24, 3, value);
- break;
- }
-
- cortexm_dap_write_coreregister_u32(target, reg, 20);
-
- LOG_DEBUG("write special reg %i value 0x%" PRIx32 " ", (int)num, value);
- break;
-
- default:
- return ERROR_COMMAND_SYNTAX_ERROR;
- }
-
- return ERROR_OK;
-}
-
static int cortex_m_read_memory(struct target *target, target_addr_t address,
uint32_t size, uint32_t count, uint8_t *buffer)
{
}
LOG_DEBUG("cpuid: 0x%8.8" PRIx32 "", cpuid);
- /* VECTRESET is not supported on Cortex-M0, M0+ and M1 */
- cortex_m->vectreset_supported = i > 1;
+ /* VECTRESET is supported only on ARMv7-M cores */
+ cortex_m->vectreset_supported = !armv7m->arm.is_armv8m && !armv7m->arm.is_armv6m;
if (i == 4) {
target_read_u32(target, MVFR0, &mvfr0);
/* test for floating point feature on Cortex-M4 */
if ((mvfr0 == MVFR0_DEFAULT_M4) && (mvfr1 == MVFR1_DEFAULT_M4)) {
LOG_DEBUG("Cortex-M%d floating point feature FPv4_SP found", i);
- armv7m->fp_feature = FPv4_SP;
+ armv7m->fp_feature = FPV4_SP;
}
} else if (i == 7 || i == 33 || i == 35 || i == 55) {
target_read_u32(target, MVFR0, &mvfr0);
/* test for floating point features on Cortex-M7 */
if ((mvfr0 == MVFR0_DEFAULT_M7_SP) && (mvfr1 == MVFR1_DEFAULT_M7_SP)) {
LOG_DEBUG("Cortex-M%d floating point feature FPv5_SP found", i);
- armv7m->fp_feature = FPv5_SP;
+ armv7m->fp_feature = FPV5_SP;
} else if ((mvfr0 == MVFR0_DEFAULT_M7_DP) && (mvfr1 == MVFR1_DEFAULT_M7_DP)) {
LOG_DEBUG("Cortex-M%d floating point feature FPv5_DP found", i);
- armv7m->fp_feature = FPv5_DP;
+ armv7m->fp_feature = FPV5_DP;
}
} else if (i == 0) {
/* Cortex-M0 does not support unaligned memory access */
for (idx = ARMV7M_NUM_CORE_REGS_NOFP;
idx < armv7m->arm.core_cache->num_regs;
idx++) {
- free(armv7m->arm.core_cache->reg_list[idx].value);
free(armv7m->arm.core_cache->reg_list[idx].feature);
free(armv7m->arm.core_cache->reg_list[idx].reg_data_type);
}
if (retval != ERROR_OK)
return retval;
- if (armv7m->trace_config.config_type != TRACE_CONFIG_TYPE_DISABLED) {
- armv7m_trace_tpiu_config(target);
+ if (armv7m->trace_config.itm_deferred_config)
armv7m_trace_itm_config(target);
- }
/* NOTE: FPB and DWT are both optional. */
{
.chain = armv7m_trace_command_handlers,
},
+ /* START_DEPRECATED_TPIU */
+ {
+ .chain = arm_tpiu_deprecated_command_handlers,
+ },
+ /* END_DEPRECATED_TPIU */
{
.name = "cortex_m",
.mode = COMMAND_EXEC,
.usage = "",
.chain = cortex_m_exec_command_handlers,
},
+ {
+ .chain = rtt_target_command_handlers,
+ },
COMMAND_REGISTRATION_DONE
};
struct target_type cortexm_target = {
.name = "cortex_m",
- .deprecated_name = "cortex_m3",
.poll = cortex_m_poll,
.arch_state = armv7m_arch_state,
projects / fw / openocd / blobdiff