#include "ao_usb.h"
#include "ao_product.h"
+#ifndef USE_USB_STDIO
+#define USE_USB_STDIO 1
+#endif
+
+#if USE_USB_STDIO
+#define AO_USB_OUT_SLEEP_ADDR (&ao_stdin_ready)
+#else
+#define AO_USB_OUT_SLEEP_ADDR (&ao_usb_out_avail)
+#endif
+
#define USB_DEBUG 0
#define USB_DEBUG_DATA 0
#define USB_ECHO 0
#define debug_data(format, args...)
#endif
-struct ao_task ao_usb_task;
-
struct ao_usb_setup {
uint8_t dir_type_recip;
uint8_t request;
/* Pending EP0 IN data */
static const uint8_t *ao_usb_ep0_in_data; /* Remaining data */
static uint8_t ao_usb_ep0_in_len; /* Remaining amount */
+static uint16_t ao_usb_ep0_in_max; /* Requested amount from host */
/* Temp buffer for smaller EP0 in data */
static uint8_t ao_usb_ep0_in_buf[2];
* but not pulled to the shadow buffer.
*/
static uint8_t ao_usb_out_avail;
-static uint8_t ao_usb_running;
+uint8_t ao_usb_running;
static uint8_t ao_usb_configuration;
-static uint8_t ueienx_0;
#define AO_USB_EP0_GOT_RESET 1
#define AO_USB_EP0_GOT_SETUP 2
return &lpc_usb_endpoint.epn[n-1].in[0];
}
+#if UNUSED
static void
ao_usb_set_epn_in(uint8_t n, uint8_t *addr, uint16_t nbytes)
{
ao_usb_set_ep(ao_usb_epn_in(n), addr, nbytes);
}
+#endif
static void
ao_usb_set_epn_out(uint8_t n, uint8_t *addr, uint16_t nbytes)
ao_usb_disable_ep(&lpc_usb_endpoint.epn[n-1].in[1]);
}
+static void
+ao_usb_reset(void)
+{
+ ao_usb_set_address(0);
+ ao_usb_configuration = 0;
+}
+
static void
ao_usb_set_ep0(void)
{
lpc_usb.epinuse = 0;
lpc_usb.epskip = 0xffffffff;
- ao_usb_set_address(0);
lpc_usb.intstat = 0xc00003ff;
- ao_usb_configuration = 0;
-
ao_usb_sram = lpc_usb_sram;
lpc_usb.epliststart = (uint32_t) (intptr_t) &lpc_usb_endpoint;
/* Clear all of the other endpoints */
for (e = 1; e <= 4; e++)
ao_usb_disable_epn(e);
-
+ ao_usb_reset();
}
static void
if (this_len > AO_USB_CONTROL_SIZE)
this_len = AO_USB_CONTROL_SIZE;
- if (this_len < AO_USB_CONTROL_SIZE)
- ao_usb_ep0_state = AO_USB_EP0_IDLE;
-
ao_usb_ep0_in_len -= this_len;
+ ao_usb_ep0_in_max -= this_len;
+
+ if (this_len < AO_USB_CONTROL_SIZE || ao_usb_ep0_in_max == 0)
+ ao_usb_ep0_state = AO_USB_EP0_IDLE;
debug_data ("Flush EP0 len %d:", this_len);
memcpy(ao_usb_ep0_tx_buffer, ao_usb_ep0_in_data, this_len);
}
static void
-ao_usb_ep0_in_start(uint8_t max)
+ao_usb_ep0_in_start(uint16_t max)
{
+ ao_usb_ep0_in_max = max;
/* Don't send more than asked for */
if (ao_usb_ep0_in_len > max)
ao_usb_ep0_in_len = max;
if (receive & AO_USB_EP0_GOT_RESET) {
debug ("\treset\n");
- ao_usb_set_ep0();
+ ao_usb_reset();
return;
}
if (receive & AO_USB_EP0_GOT_SETUP) {
}
}
-static uint16_t control_count;
+#if USB_DEBUG
static uint16_t int_count;
static uint16_t in_count;
static uint16_t out_count;
static uint16_t reset_count;
+#endif
void
lpc_usb_irq_isr(void)
/* Handle OUT packets */
if (intstat & (1 << LPC_USB_INT_EPOUT(AO_USB_OUT_EP))) {
+#if USB_DEBUG
++out_count;
+#endif
_rx_dbg1("RX ISR", *ao_usb_epn_out(AO_USB_OUT_EP));
ao_usb_out_avail = 1;
_rx_dbg0("out avail set");
- ao_wakeup(&ao_stdin_ready);
+ ao_wakeup(AO_USB_OUT_SLEEP_ADDR)
_rx_dbg0("stdin awoken");
}
/* Handle IN packets */
if (intstat & (1 << LPC_USB_INT_EPIN(AO_USB_IN_EP))) {
+#if USB_DEBUG
++in_count;
+#endif
_tx_dbg1("TX ISR", *ao_usb_epn_in(AO_USB_IN_EP));
ao_usb_in_pending = 0;
ao_wakeup(&ao_usb_in_pending);
ao_arch_block_interrupts();
while ((c = _ao_usb_pollchar()) == AO_READ_AGAIN)
- ao_sleep(&ao_stdin_ready);
+ ao_sleep(AO_USB_OUT_SLEEP_ADDR);
ao_arch_release_interrupts();
return c;
}
{
ao_arch_block_interrupts();
+#if HAS_USB_PULLUP
+ ao_gpio_set(AO_USB_PULLUP_PORT, AO_USB_PULLUP_PIN, AO_USB_PULLUP, 0);
+#endif
/* Disable interrupts */
lpc_usb.inten = 0;
/* Turn off USB clock */
lpc_scb.usbclkdiv = 0;
- /* Disable USB PHY */
- lpc_scb.pdruncfg |= (1 << LPC_SCB_PDRUNCFG_USBPAD_PD);
+ /* Disable USB PHY and PLL */
+ lpc_scb.pdruncfg |= ((1 << LPC_SCB_PDRUNCFG_USBPAD_PD) |
+ (1 << LPC_SCB_PDRUNCFG_USBPLL_PD));
/* Disable USB registers and RAM */
lpc_scb.sysahbclkctrl &= ~((1 << LPC_SCB_SYSAHBCLKCTRL_USB) |
int t;
/* Enable USB pins */
-#if HAS_USB_CONNECT
+#if HAS_LPC_USB_CONNECT
lpc_ioconf.pio0_6 = ((LPC_IOCONF_FUNC_USB_CONNECT << LPC_IOCONF_FUNC) |
(LPC_IOCONF_MODE_INACTIVE << LPC_IOCONF_MODE) |
(0 << LPC_IOCONF_HYS) |
lpc_scb.pdruncfg &= ~(1 << LPC_SCB_PDRUNCFG_USBPLL_PD);
lpc_scb.usbpllclksel = (LPC_SCB_SYSPLLCLKSEL_SEL_SYSOSC << LPC_SCB_SYSPLLCLKSEL_SEL);
- lpc_scb.usbpllclkuen = (1 << LPC_SCB_USBPLLCLKUEN_ENA);
lpc_scb.usbpllclkuen = (0 << LPC_SCB_USBPLLCLKUEN_ENA);
lpc_scb.usbpllclkuen = (1 << LPC_SCB_USBPLLCLKUEN_ENA);
while (!(lpc_scb.usbpllclkuen & (1 << LPC_SCB_USBPLLCLKUEN_ENA)))
;
lpc_scb.usbclksel = 0;
+ lpc_scb.usbclkuen = (0 << LPC_SCB_USBCLKUEN_ENA);
+ lpc_scb.usbclkuen = (1 << LPC_SCB_USBCLKUEN_ENA);
+ while (!(lpc_scb.usbclkuen & (1 << LPC_SCB_USBCLKUEN_ENA)))
+ ;
/* Turn on USB clock, use 48MHz clock unchanged */
lpc_scb.usbclkdiv = 1;
ao_arch_nop();
ao_usb_set_ep0();
+
+#if HAS_USB_PULLUP
+ ao_gpio_set(AO_USB_PULLUP_PORT, AO_USB_PULLUP_PIN, AO_USB_PULLUP, 1);
+#endif
}
#if USB_ECHO
void
ao_usb_init(void)
{
+#if HAS_USB_PULLUP
+ ao_enable_output(AO_USB_PULLUP_PORT, AO_USB_PULLUP_PIN, AO_USB_PULLUP, 0);
+#endif
+
ao_usb_enable();
debug ("ao_usb_init\n");
#if USB_DEBUG
ao_cmd_register(&ao_usb_cmds[0]);
#endif
-#if !USB_ECHO
+#if USE_USB_STDIO
ao_add_stdio(_ao_usb_pollchar, ao_usb_putchar, ao_usb_flush);
#endif
}