* 98mm [Giant Leap](http://giantleaprocketry.com) Dynawind air frame
* 75mm [PML](http://www.publicmissiles.com) phenolic motor mount
* [Shock Wave Rocketry](http://shockwaverocketry.com/) fiberglass 98mm Von Karman 6:1 nose cone
-* custom fins, using 1/8 inch birch plywood laminated with carbon fiber
+* custom fins, using 6/16 inch birch plywood laminated with carbon fiber
and a fibreglass sanding veil
* 3/8 inch birch plywood centering rings and bulkheads, CNC milled, the two
that hold the fins are double thickness (3/4 inch) and notched for perfect
The OpenRocket design file is
[2YikStik.ork](/rockets/airframes/2YikStik/2YikStik.ork).
-## Build
-
-Parts gathered during October 2010. Built mostly during April and May 2011.
-
-The nose cone was custom fabricated by Jeff Lane at
-[Shockwave Rocketry](http://shockwaverocketry.com), with thermistors embedded.
-
-The fins are 3/16 inch birch ply, tapered on the leading and trailing edges,
-then covered with one layer of 5.7 oz 2x2 twill carbon fiber and a layer of
-6 oz glass as a sanding veil, all vacuum bagged with West Systems laminating
-epoxy using a kitchen food saver appliance.
-
-The airframe tubing is Giant Leap Rocketry 98mm Magnaframe-based Dynawind,
-except for a short section behind the nose cone that uses the older phenolic
-based Dynawind because of the slightly larger inside diameter being a better
-fit for the glass nose cone shoulder.
-
-The tailcone is a no-longer-available Giant Leap 98-75mm Slimline tailcone.
-
-All rings and bulkheads were cut using a CNC milling machine from 3/8 inch
-birch plywood. The fin forward and leading edge rings are made from 3/4 inch
-thick assemblies made by laminating two such rings with wood glue, to provide
-sufficient depth for milled fin slots.
-
-Assembly techniques were "nothing special" except for the electronics...
-
-[Build Photos](http://gallery.gag.com/rockets/2yikstik/)
-
### Thermistors ###
The temperature sensors chosen are 0.8 mm diameter glass bead NTC thermistors
Installing the electronics in the fin can bay was .. interesting. More later.
+## Build
+
+Parts gathered during October 2010. Built mostly during April and May 2011.
+
+The nose cone was custom fabricated by Jeff Lane at
+[Shockwave Rocketry](http://shockwaverocketry.com), with thermistors embedded.
+
+The fins are 3/16 inch birch ply, tapered on the leading and trailing edges,
+then covered with one layer of 5.7 oz 2x2 twill carbon fiber and a layer of
+6 oz glass as a sanding veil, all vacuum bagged with West Systems laminating
+epoxy using a kitchen food saver appliance.
+
+The airframe tubing is Giant Leap Rocketry 98mm Magnaframe-based Dynawind,
+except for a short section behind the nose cone that uses the older phenolic
+based Dynawind because of the slightly larger inside diameter being a better
+fit for the glass nose cone shoulder.
+
+The tailcone is a no-longer-available Giant Leap 98-75mm Slimline tailcone.
+
+All rings and bulkheads were cut using a CNC milling machine from 3/8 inch
+birch plywood. The fin forward and leading edge rings are made from 3/4 inch
+thick assemblies made by laminating two such rings with wood glue, to provide
+sufficient depth for milled fin slots.
+
+Assembly techniques were "nothing special" except for the electronics... but
+I kept a [log](/rockets/airframes/2YikStik/buildlog) that may be of interest.
+
+[Photos](http://gallery.gag.com/rockets/2yikstik/)
+
## Publicity
## Flights
The original objective of flying 2YikStik at NCR's Mile High Mayhem 2011
was not met due to weather conditions unfavorable for a high altitude launch.
-While it's possible we might be able to attend another NCR launch this summer,
-at this point we likely won't fly 2YikStik until LDRS 30.
+We currently hope to fly 2YikStik at [LDRS 30](http://ldrs30.org/).