-# TeleMini #
+[[!meta title="TeleMini"]]
+# TeleMini
-TeleMini version 2.0 is a small, baro-only recording dual-deploy
-altimeter for model rocketry with integrated telemetry link. It's
-currently in development, with production planned to start in the fall
-of 2013.
+This is a very small, baro-only recording dual-deploy altimeter for
+model rocketry with integrated telemetry link.
+
+Version 3.0 is back from fabrication and are ready for sale. Units are
+available from the [Garbee and Garbee](http://shop.gag.com) web store.
For the latest TeleMini firmware and related ground station software, please
visit the [AltOS](../AltOS) page on this site.
-These are photos of our current prototype version:
+Here's two photos of v3.0, top and bottom:
-<a href="v2.0/telemini-top.jpg"> <img src="v2.0/telemini-top-thumb.jpg"></a>
-<a href="v2.0/telemini-parts.jpg"> <img src="v2.0/telemini-parts-thumb.jpg"></a>
+<a href="v3.0/telemini-v3.0-top.jpg"> <img src="v3.0/telemini-v3.0-top-640.jpg"></a>
+<br>
+<a href="v3.0/telemini-v3.0-bottom.jpg"> <img src="v3.0/telemini-v3.0-bottom-640.jpg"></a>
## Features ##
### User View ###
- * Recording altimeter for model rocketry
- * Supports dual deployment (can fire 2 ejection charges)
- * 70cm ham-band transceiver for telemetry downlink
- * Barometric pressure sensor good to 100k' feet MSL
- * Designed to use any battery from 3.7 - 12V
- * Screw terminals for pyro connectors, switch and external battery
- * Built-in USB connector for configuration and data download
- * 1.5 x 0.8 inch board designed to fit inside 24mm airframe coupler tube
+* Recording altimeter for model rocketry
+* Supports dual deployment (can fire 2 ejection charges)
+* 70cm ham-band transceiver for telemetry downlink
+* Barometric pressure sensor good to 100k feet MSL
+* Designed to use a single LiPo rechargeable battery
+* 512kB flight data storage
+* 1.7 x 0.5 inch board designed to fit inside 18mm airframe coupler tube
### Developer View ###
* Hardware Features
- * [TI CC1111F32](http://focus.ti.com/docs/prod/folders/print/cc1111f32.html) Low Power RF System-on-Chip
- * Sub-1Ghz transceiver
- * 8051 MCU
+ * [ST STM32F042G6](http://www.st.com/content/st_com/en/products/microcontrollers/stm32-32-bit-arm-cortex-mcus/stm32f0-series/stm32f0x2/stm32f042g6.html) system on chip
+ * ARM Cortex-M0 MCU
* 32k Flash
- * 4k RAM
+ * 6k RAM
* USB 2.0
- * 6 12-bit analog inputs (11 bits with single-ended sensors)
- * 2 channels of serial I/O
* digital I/O
- * [Measurement Specialties MS5607](http://www.meas-spec.com/product/pressure/MS5607-02BA03.aspx) pressure sensor
- * 1MB SPI flash
+ * [TI CC1200](http://www.ti.com/product/cc1200) High Performance RF Transceiver for Narrowband Systems
+
+ * [Measurement Specialties MS5607](http://www.te.com/usa-en/product-CAT-BLPS0035.html) pressure sensor
+ * [Macronix MX25L4006E](http://www.macronix.com/Lists/Datasheet/Attachments/5087/MX25L4006E,%203V,%204Mb,%20v1.6.pdf) 512kB serial flash memory
* Software Features
- * Written mostly in C with some 8051 assembler
- * Runs from on-chip flash, uses on-chip RAM, stores flight data to
- on-board flash memory
+ * Written mostly in C with some ARM assembler
* Tools Used
* [gEDA](http://www.gpleda.org/) for schematic capture and PCB layout
* [SDCC](http://sdcc.sourceforge.net/) compiler and source debugger
* Licenses
* The hardware is licensed under the [TAPR](http://www.tapr.org) [Open Hardware License](http://www.tapr.org/ohl.html)
- * The software is licensed [GPL version 2](http://www.gnu.org/licenses/old-licenses/gpl-2.0.html)
+ * The software is licensed [GPL version 2 or later](http://www.gnu.org/licenses/old-licenses/gpl-2.0.html)
+
+## Older Versions ##
+
+[Version 1.0](v1.0). Same width (0.5 inches), but doesn't have the
+rear two mounting holes so it's a bit shorter (1.5 inches instead of
+1.67 inches).
## Artifacts ##
which is available in [html](../AltOS/doc/altusmetrum.html) and
[pdf](../AltOS/doc/altusmetrum.pdf) formats.
+An outline of the board with drill hole locations is available in
+[pdf](../Documents/telemini-v3-outline.pdf) format.
+
The hardware design files can be found on [git.gag.com](http://git.gag.com)
in the project [hw/telemini](http://git.gag.com/?p=hw/telemini;a=summary).
-## [History of TeleMini](history) ##
+For those who don't have ready access to the gEDA suite, here are pdf snapshots
+of the files for Production PCB version 3.0 in more easily readable form.
+
+* [schematic](v3.0/telemini-sch.pdf)
+* [pcb artwork](v3.0/telemini-pcb.pdf)
+* [bill of materials](v3.0/partslist.csv)
+
projects / web / altusmetrum / blobdiff