This is a recording dual-deploy altimeter for high power model rocketry
with integrated GPS and telemetry link.
-Production units will be available soon from the
+Production units are available from the
[Garbee and Garbee](http://auric.gag.com) web store.
-These are photos of our current version,
-which includes an integrated GPS receiver and patch antenna:
+These are photos of our current production version, which includes an
+integrated GPS receiver with active patch antenna:
-<a href="v0.2/cimg5164-cropped.jpg"> <img src="v0.2/cimg5164-thumb.jpg"></a>
-<a href="v0.2/cimg5171-cropped.jpg"> <img src="v0.2/cimg5171-thumb.jpg"></a>
-
-And this is a photo of our original board with serial port for off-board GPS,
-without the big off-board 1000uF cap from the original ejection circuit:
-
-<a href="v0.1/loadedpair.jpg"> <img src="v0.1/loadedpair-thumb.jpg"></a>
+<a href="v1.0/cimg5972-crop.jpg"> <img src="v1.0/cimg5972-thumb.jpg"></a>
+<a href="v1.0/cimg5974-crop.jpg"> <img src="v1.0/cimg5974-thumb.jpg"></a>
## Motivation ##
* SPI interface
* other parts in this Atmel DataFlash series can optionally be used
* [SkyTraq](http://www.skytraq.com.tw/) Venus634FLPx GPS receiver
- * on-board passive patch antenna
- * U.FL connector with 3.3V DC for optional external amplified antenna
+ * on-board [Taoglas AP.17A.01](http://www.taoglas.com/antennas/GPS_Antennas/Internal_GPS_-_Active_Patch_Modules/)
+ single-stage active patch antenna
+ * U.FL connector with 3.3V DC can be re-purposed for optional external amplified antennas
* async serial interface
* [Freescale MP3H6115A](http://www.freescale.com/webapp/search.partparamdetail.framework?PART_NUMBER=MP3H6115A6U) pressure sensor
* [Freescale MMA2202EG](http://www.freescale.com/webapp/search.partparamdetail.framework?PART_NUMBER=MMA2202EG) 50g accelerometer. Can use 40-200g variants!
* The hardware is licensed under the [TAPR](http://www.tapr.org) [Open Hardware License](http://www.tapr.org/ohl.html)
* The software is licensed [GPL version 2](http://www.gnu.org/licenses/old-licenses/gpl-2.0.html)
-### v0.1 Differences ###
-
-* 2.5 x 1 inch board with all parts mounted on one side
-* 4-pin PicoBlade serial port connector for attachment of external GPS module
-* USB connector projected approximately 3mm over the edge of the board
-* Debug connector used 4 IC socket pins on 100 mil centers
-* no companion board interface
-* [Microchip 25LC1024](http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en520389) CMOS serial EEPROM instead of DataFlash
- * 128k x 8
- * SPI interface
-* [Microchip MCP9700A](http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en027103) discrete temperature sensor
-* used 1000uF electrolytic capacitor charged to 5V for pyro supply
-* two LEDs instead of one attached to CPU
-
-The elimination of the discrete temperature sensor and second LED were
-necessary to support the companion board interface added in v0.2.
-
## [Production History](../production) ##
## [Flight Logs](flightlogs) ##
-## Problems ##
-
-* The CC1111F32 is a 36-pin QFN package, which necessitates reflow
- soldering. Since we needed to reflow solder anyway, and because TI used
- them in their reference design, we went a little crazy and used 0402
- passive parts everywhere. That means working under a microscope to
- place parts! Without an inspection microscope, loading and testing these
- boards might be impossible.
-
-* The addition of on-board GPS in v0.2 means that the total power consumption
- can exceed the rate at which we draw power from the USB interface,
- particularly when the GPS is in cold start mode. This means a battery must
- be attached during operation, and also that the battery will only charge
- effectively from USB when the board is turned off.
-
-* The v0.1 artwork had three issues, two of which required physical rework
- on each board. All of these issues were fixed in v0.2.
-
- * The USB connector footprint was placed wrong, so that the
- connector hung out over the edge of the board instead of being
- flush.
- * We needed chip select on the SPI memory. To fix that, we gave up the
- ability to put the accelerometer into self-test mode and used that
- GPIO line to pull chip select on the memory, which required two
- cuts and two jumpers.
- * The igniter sense circuits each needed a second resistor to
- complete the voltage divider so our 3.3V CPU ADC could read the
- 5V ejection voltage. This was fixed by changing two resistor
- values, and tacking two additional resistors onto the board
- with jumpers to ground.
-
## Artifacts ##
+The user manual for TeleMetrum is available in
+[html](doc/telemetrum-doc.html) and [pdf](doc/telemetrum-doc.pdf)
+formats.
+
The hardware design current gEDA files are available from
[git.gag.com](http://git.gag.com) in the project
[hw/telemetrum](http://git.gag.com/?p=hw/telemetrum;a=summary).
For those who don't have ready access to the gEDA suite, here are pdf snapshots
of files in more easily readable form.
-* These are from the v0.2 branch:
- * [schematic](v0.2/telemetrum.pdf)
- * [pcb artwork](v0.2/telemetrum.pcb.pdf)
- * [bill of materials](v0.2/partslist.csv)
-* These are as of the working-v0.1 tag:
- * [schematic](v0.1/telemetrum.pdf)
- * [pcb artwork](v0.1/telemetrum.pcb.pdf)
- * [bill of materials](v0.1/telemetrum.bom)
+* Production PCB version v1.0:
+ * [schematic](v1.0/telemetrum.pdf)
+ * [pcb artwork](v1.0/telemetrum.pcb.pdf)
+ * [bill of materials](v1.0/partslist.csv)
Our [AltOS](../AltOS) firmware works well enough that we now routinely fly
TeleMetrum with no backup. Rockets with v0.1 boards have exceeded 50g
## Future Plans ##
-As of early March 2010, three prototypes of v0.2 exist and have flown with
-great success. We will initiate a production run shortly with the goal of
-making TeleMetrum available in assembled and tested form to others in the
-rocketry hobby in time for the 2010 flying season.
+As of May 2010, version v1.0 is available for sale from the
+[Garbee and Garbee](http://auric.gag.com) web store.
+
+Because we understand that not everyone uses Linux, development of a new
+cross-platform ground station program written in Java is underway for use with
+[AltOS](../AltOS).
+
+## Problems ##
-Because we understand that not everyone uses Linux, we are investigating
-the best way to make a cross-platform ground station program for use with
-[AltOS](../AltOS), perhaps in Java...
+* The CC1111F32 is a 36-pin QFN package, which necessitates reflow
+ soldering. Since we needed to reflow solder anyway, and because TI used
+ them in their reference design, we went a little crazy and used 0402
+ passive parts everywhere. That means working under a microscope to
+ place parts! Without an inspection microscope, loading and testing these
+ boards might be impossible.
+
+* The addition of on-board GPS in v0.2 means that the total power consumption
+ can exceed the rate at which we draw power from the USB interface,
+ particularly when the GPS is in cold start mode. This means a battery must
+ be attached during operation, and also that the battery will only charge
+ effectively from USB when the board is turned off.
+
+## History ##
+
+### v0.2 ###
+
+* 100ma LDO regulator instead of the current 150ma part
+* no C38 footprint
+* different value for C36 reset capacitor
+
+These are photos of our second version, which included the integrated Venus
+GPS receiver, but with a passive patch antenna that turned out to have
+disappointing performance due to our many PCB geometry constraints. It also
+used a voltage regulator with less capacity which we felt was marginal for
+supporting the companion boards we have planned:
+
+<a href="v0.2/cimg5164-cropped.jpg"> <img src="v0.2/cimg5164-thumb.jpg"></a>
+<a href="v0.2/cimg5171-cropped.jpg"> <img src="v0.2/cimg5171-thumb.jpg"></a>
+
+Other than cleaning up the silkscreen, the differences between v0.2 and our
+current v1.0 boards were really quite small:
+
+* 100ma LDO regulator instead of the current 150ma part
+* no C38 footprint
+* different value for C36 reset capacitor
+
+The schematics and PCB artwork for this version are on the v0.2 branch in
+our git repository, here are pdf copies for easy reference:
+
+ * [schematic](v0.2/telemetrum.pdf)
+ * [pcb artwork](v0.2/telemetrum.pcb.pdf)
+ * [bill of materials](v0.2/partslist.csv)
+
+### v0.1 ###
+
+And this is a photo of our original board with serial port for off-board GPS,
+without the big off-board 1000uF cap from the original ejection circuit:
+
+<a href="v0.1/loadedpair.jpg"> <img src="v0.1/loadedpair-thumb.jpg"></a>
+
+The differences between v0.1 and later boards were more substantial:
+
+* 2.5 x 1 inch board with all parts mounted on one side
+* 4-pin PicoBlade serial port connector for attachment of external GPS module
+* USB connector projected approximately 3mm over the edge of the board
+* Debug connector used 4 IC socket pins on 100 mil centers
+* no companion board interface
+* 50ma LDO regulator on early boards, later boards used a 100ma part
+* [Microchip 25LC1024](http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en520389) CMOS serial EEPROM instead of DataFlash
+ * 128k x 8
+ * SPI interface
+* [Microchip MCP9700A](http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en027103) discrete temperature sensor
+* used 1000uF electrolytic capacitor charged to 5V for pyro supply
+* two LEDs instead of one attached to CPU
+
+The elimination of the discrete temperature sensor and second LED were
+necessary to support the companion board interface added in v0.2.
+
+The v0.1 artwork had three issues, two of which required physical rework
+on each board. All of these issues were fixed in v0.2.
+
+* The USB connector footprint was placed wrong, so that the
+ connector hung out over the edge of the board instead of being
+ flush.
+* We needed chip select on the SPI memory. To fix that, we gave up the
+ ability to put the accelerometer into self-test mode and used that
+ GPIO line to pull chip select on the memory, which required two
+ cuts and two jumpers.
+* The igniter sense circuits each needed a second resistor to
+ complete the voltage divider so our 3.3V CPU ADC could read the
+ 5V ejection voltage. This was fixed by changing two resistor
+ values, and tacking two additional resistors onto the board
+ with jumpers to ground.
+
+The schematics and PCB artwork for this version as of the working-v0.1 tag
+are available here are pdf copies for easy reference:
+
+ * [schematic](v0.1/telemetrum.pdf)
+ * [pcb artwork](v0.1/telemetrum.pcb.pdf)
+ * [bill of materials](v0.1/telemetrum.bom)