# TeleMetrum
This is a recording dual-deploy altimeter for high power model rocketry
-with integrated telemetry link.
-
-<a href="loadedpair.jpg"> <img src="loadedpair-thumb.jpg"></a>
-<a href="rawfront.jpg"> <img src="rawfront-thumb.jpg"></a>
-<a href="rawback.jpg"> <img src="rawback-thumb.jpg"></a>
-
-## Motivation ##
-
-Bdale and Keith both own
-[BeeLine](http://www.bigredbee.com/BeeLine.htm)
-trackers from
-[Big Red Bee](http://www.bigredbee.com), and are pretty happy with them.
-They use a PIC processor and a TI CC1050 transmitter chip, and
-operate in the ham radio 70cm band.
-
-One weekend while attending a conference together, we got to wondering if
-we couldn't adapt one to use as a downlink for the
-[AltusMetrum](../AltusMetrum/) altimeter board in addition to direction
-finding after flight. That caused us to start thinking about other things
-in the design we might want to tweak, and before long we were working on the
-design of a new tracker board derived from the BeeLine design.
-Another friend at the same conference showed us a board he was working on
-using a different part in the same TI series, that integrated a transceiver
-and CPU on the same chip.
-It didn't take us long to realize that with such a part we could combine and
-simplify things by building a new altimeter with integrated RF link!
+with integrated GPS and telemetry link.
+
+For the latest TeleMetrum firmware and related ground station software, please
+visit the [AltOS](../AltOS) page on this site.
+
+These are photos of the previous production version (we haven't taken good
+pictures of v1.2 yet):
+
+<a href="v1.1/telemetrum-v1.1-thside.jpg"> <img src="v1.1/telemetrum-v1.1-thside-thumb.jpg"></a>
+<a href="v1.1/telemetrum-v1.1-smtside.jpg"> <img src="v1.1/telemetrum-v1.1-smtside-thumb.jpg"></a>
## Features ##
* Supports dual deployment (can fire 2 ejection charges)
* 70cm ham-band transceiver for telemetry downlink
* Barometric pressure sensor good to 45k feet MSL
-* Temperature sensor
-* 1-axis high-g accelerometer for motor characterization
+* 1-axis 70-g accelerometer for motor characterization
+* On-board, integrated GPS receiver
* On-board non-volatile memory for flight data storage
-* Serial port for attachment of GPS module
* USB for power, configuration, and data recovery
* Integrated support for LiPo rechargeable batteries
-* 2.5 x 1 inch board designed to fit inside 29mm airframe coupler tube
+* Uses LiPo to fire e-matches, can be factory modified to support separate pyro battery
+* 2.75 x 1 inch board designed to fit inside 29mm airframe coupler tube
### Developer View ###
-* [TI CC1111F32](http://focus.ti.com/docs/prod/folders/print/cc1111f32.html) Low Power RF System-on-Chip
- * Sub-1Ghz transceiver
- * 8051 MCU
- * 32k Flash
- * 4k RAM
- * USB 2.0
- * 6 12-bit analog inputs (11 bits with single-ended sensors)
- * 2 channels of serial I/O
- * digital I/O
-* [Microchip 25LC1024](http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en520389) CMOS serial EEPROM
- * 128k x 8
- * SPI interface
-* Various Sensors
+* Hardware Features
+ * [TI CC1111F32](http://focus.ti.com/docs/prod/folders/print/cc1111f32.html) Low Power RF System-on-Chip
+ * Sub-1Ghz transceiver
+ * 8051 MCU
+ * 32k Flash
+ * 4k RAM
+ * USB 2.0
+ * 6 12-bit analog inputs (11 bits with single-ended sensors)
+ * 2 channels of serial I/O
+ * digital I/O
+ * [Winbond W25Q16](http://www.winbond.com/NR/exeres/A3D21C82-A0B6-4586-A770-2F0883A805FF.htm) serial flash memory
+ * 2M x 8
+ * SPI interface
+ * [SkyTraq](http://www.skytraq.com.tw/) Venus634FLPx GPS receiver
+ * on-board [Taoglas AP.17A.01](http://www.taoglas.com/antennas/GPS_Antennas/Internal_GPS_-_Active_Patch_Modules/)
+ single-stage active patch antenna
+ * U.FL connector with 3.3V DC can be re-purposed for optional external amplified antennas
+ * async serial interface
* [Freescale MP3H6115A](http://www.freescale.com/webapp/search.partparamdetail.framework?PART_NUMBER=MP3H6115A6U) pressure sensor
- * [Freescale MMA2202EG](http://www.freescale.com/webapp/search.partparamdetail.framework?PART_NUMBER=MMA2202EG) 50g accelerometer. Can use 40-200g variants!
- * [Microchip MCP9700A](http://www.microchip.com/wwwproducts/Devices.aspx?dDocName=en027103) temperature sensor
-* Software Features (planned)
+ * [Analog Devices ADXL78](http://www.analog.com/en/mems-sensors/inertial-sensors/adxl78/products/product.html) 70g accelerometer.
+* Software Features
* Written mostly in C with some 8051 assembler
* Runs from on-chip flash, uses on-chip RAM, stores flight data to
- serial EEPROM chip
+ serial DataFlash chip
* USB serial emulation for "console" interface
* Tools Used
* [gEDA](http://www.gpleda.org/) for schematic capture and PCB layout
* The hardware is licensed under the [TAPR](http://www.tapr.org) [Open Hardware License](http://www.tapr.org/ohl.html)
* The software is licensed [GPL version 2](http://www.gnu.org/licenses/old-licenses/gpl-2.0.html)
-## [Production History](production) ##
+## [Production History](../production) ##
## [Flight Logs](flightlogs) ##
-## Problems ##
-
-* The CC1111F32 is a 36-pin QFN package, which necessitates reflow
- soldering. Since we needed to reflow solder anyway, and because TI used
- them in their reference design, we went a little crazy and used 0402
- passive parts everywhere. That means working under a microscope to
- place parts! Without an inspection microscope, loading and testing these
- boards might be impossible.
-
-* The v0.1 artwork has the USB connector footprint placed wrong, so that the
- connector hangs out over the edge of the board instead of being flush with
- the edge.
+## Videos ##
-* The v0.1 artwork has two issues that require cuts and jumps. The first is
- that we need chip select on the SPI memory. To fix that, we give up the
- ability to put the accelerometer into self-test mode and use that GPIO line
- to pull chip select on the memory. The second is that the igniter sense
- circuits each need a second resistor to complete the voltage divider so our
- 3.3V CPU ADC can read the 5V ejection voltage. This is fixed by changing
- two resistor values, and tacking two additional resistors onto the board
- with jumpers to ground.
+There are a number of TeleMetrum customer and other
+[videos on YouTube](http://www.youtube.com/results?search_query=telemetrum)
## Artifacts ##
+There is a single manual for TeleMetrum and all other Altus Metrum products,
+which is available in [html](../AltOS/doc/altusmetrum.html) and
+[pdf](../AltOS/doc/altusmetrum.pdf) formats.
+
The hardware design current gEDA files are available from
[git.gag.com](http://git.gag.com) in the project
-[hw/telemetrum](http://git.gag.com/?p=hw/telemetrum;a=summary). The 'fab'
-tag on the master branch reflects
-the artwork as sent out for PCB fab. The 'loaded' tag on the master branch
-indicates the parts Bdale loads for a functional board, but the schematic
-does not reflect the cuts and jumps or added resistors. The 'nextcut' branch
-is work towards our next PCB revision. The 'ground' branch has a cut-down
-schematic used to generate the BOM for partially loading boards to use in
-the matching [TeleTerra](../TeleTerra) ground station design.
-
-For those who don't have ready access to the gEDA suite, here are pdf snapshots
-of files in more easily readable form. The schematic and BOM are from the
-'nextcut' branch as of 20 April 2009, the artwork is of the v0.1 boards:
+[hw/telemetrum](http://git.gag.com/?p=hw/telemetrum;a=summary).
-* [schematic](telemetrum.pdf)
-* [pcb artwork](telemetrum.pcb.pdf)
-* [bill of materials](telemetrum.bom)
+Work on the next version proceeds on the master branch, with occasional
+temporary branches created when Bdale is making some major / speculative
+change. Branched with names like 'v1.2' document what we're actually flying
+on the respective PCB revisions.
+For those who don't have ready access to the gEDA suite, here are pdf snapshots
+of the files for Production PCB version 1.2 in more easily readable form.
+
+* [schematic](v1.2/telemetrum.pdf)
+* [pcb artwork](v1.2/telemetrum.pcb.pdf)
+* [bill of materials](v1.2/partslist.csv)
+
+Rockets we know of flying with TeleMetrum boards have exceeded 50g acceleration,
+been well above Mach 1, and reached altitudes
+greater than 25k feet AGL with great results. Keith's second generation
+ground station program called AltosUI works on Windows, Mac, and Linux systems
+and logs telemetry to disk, displays current and max values for key parameters
+during flight, includes voice synthesis during the flight so that
+our eyes can stay on the rockets, and even includes live display of rocket
+position over moving maps! After flight, altosui can extract the
+complete flight log from TeleMetrum, can display plots of the data from either
+the telemetry received by radio or the onboard flight log, can output a kml
+file for use with [Google Earth](http://earth.google.com), and can also
+output all the flight data as a csv file for easy import to spreadsheet
+programs or other analysis tools allowing you to perform whatever
+custom analysis you can envision! More details on the software,
+including full source code and pre-built packages
+can be found on the [AltOS](../AltOS) page on this site. Feel free to
+download the software and try it before purchasing our hardware!
+
+## Future Plans ##
+
+TeleMetrum v1.2 is now available for sale. Eventually we'll run out of v1.2
+boards, and by then no dobut we'll have found more things to tweak...
+
+## [History of TeleMetrum](history) ##
-Keith has working firmware that has now been flown once and successfully
-collected flight data to apogee. The source is also available from
-[git.gag.com](http://git.gag.com) in the project
-[fw/altos](http://git.gag.com/?p=fw/altos;a=summary). Not that actually
-building these sources requires a modifified version of sdcc and a set of
-helper utilities that we're not publishing since we hope to have the important
-bits accepted upstream shortly. Watch this space for more details soon.
projects / web / altusmetrum / blobdiff