+ <section>
+ <title>Configurable Parameters</title>
+ <para>
+ Configuring a TeleMetrum board for flight is very simple. Because we
+ have both acceleration and pressure sensors, there is no need to set
+ a "mach delay", for example. The few configurable parameters can all
+ be set using a simple terminal program over the USB port or RF link
+ via TeleDongle.
+ </para>
+ <section>
+ <title>Radio Channel</title>
+ <para>
+ Our firmware supports 10 channels. The default channel 0 corresponds
+ to a center frequency of 434.550 Mhz, and channels are spaced every
+ 100 khz. Thus, channel 1 is 434.650 Mhz, and channel 9 is 435.550 Mhz.
+ At any given launch, we highly recommend coordinating who will use
+ each channel and when to avoid interference. And of course, both
+ TeleMetrum and TeleDongle must be configured to the same channel to
+ successfully communicate with each other.
+ </para>
+ <para>
+ To set the radio channel, use the 'c r' command, like 'c r 3' to set
+ channel 3.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board DataFlash chip.
+ </para>
+ </section>
+ <section>
+ <title>Apogee Delay</title>
+ <para>
+ Apogee delay is the number of seconds after TeleMetrum detects flight
+ apogee that the drogue charge should be fired. In most cases, this
+ should be left at the default of 0. However, if you are flying
+ redundant electronics such as for an L3 certification, you may wish
+ to set one of your altimeters to a positive delay so that both
+ primary and backup pyrotechnic charges do not fire simultaneously.
+ </para>
+ <para>
+ To set the apogee delay, use the [FIXME] command.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board DataFlash chip.
+ </para>
+ </section>
+ <section>
+ <title>Main Deployment Altitude</title>
+ <para>
+ By default, TeleMetrum will fire the main deployment charge at an
+ elevation of 250 meters (about 820 feet) above ground. We think this
+ is a good elevation for most airframes, but feel free to change this
+ to suit. In particular, if you are flying two altimeters, you may
+ wish to set the
+ deployment elevation for the backup altimeter to be something lower
+ than the primary so that both pyrotechnic charges don't fire
+ simultaneously.
+ </para>
+ <para>
+ To set the main deployment altitude, use the [FIXME] command.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board DataFlash chip.
+ </para>
+ </section>
+ </section>
+ <section>
+ <title>Calibration</title>
+ <para>
+ There are only two calibrations required for a TeleMetrum board, and
+ only one for TeleDongle.
+ </para>
+ <section>
+ <title>Radio Frequency</title>
+ <para>
+ The radio frequency is synthesized from a clock based on the 48 Mhz
+ crystal on the board. The actual frequency of this oscillator must be
+ measured to generate a calibration constant. While our GFSK modulation
+ bandwidth is wide enough to allow boards to communicate even when
+ their oscillators are not on exactly the same frequency, performance
+ is best when they are closely matched.
+ Radio frequency calibration requires a calibrated frequency counter.
+ Fortunately, once set, the variation in frequency due to aging and
+ temperature changes is small enough that re-calibration by customers
+ should generally not be required.
+ </para>
+ <para>
+ To calibrate the radio frequency, connect the UHF antenna port to a
+ frequency counter, set the board to channel 0, and use the 'C'
+ command to generate a CW carrier. Wait for the transmitter temperature
+ to stabilize and the frequency to settle down.
+ Then, divide 434.550 Mhz by the
+ measured frequency and multiply by the current radio cal value show
+ in the 'c s' command. For an unprogrammed board, the default value
+ is 1186611. Take the resulting integer and program it using the 'c f'
+ command. Testing with the 'C' command again should show a carrier
+ within a few tens of Hertz of the intended frequency.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board DataFlash chip.
+ </para>
+ </section>
+ <section>
+ <title>Accelerometer</title>
+ <para>
+ The accelerometer we use has its own 5 volt power supply and
+ the output must be passed through a resistive voltage divider to match
+ the input of our 3.3 volt ADC. This means that unlike the barometric
+ sensor, the output of the acceleration sensor is not ratiometric to
+ the ADC converter, and calibration is required. We also support the
+ use of any of several accelerometers from a Freescale family that
+ includes at least +/- 40g, 50g, 100g, and 200g parts. Using gravity,
+ a simple 2-point calibration yields acceptable results capturing both
+ the different sensitivities and ranges of the different accelerometer
+ parts and any variation in power supply voltages or resistor values
+ in the divider network.
+ </para>
+ <para>
+ To calibrate the acceleration sensor, use the 'c a 0' command. You
+ will be prompted to orient the board vertically with the UHF antenna
+ up and press a key, then to orient the board vertically with the
+ UHF antenna down and press a key.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board DataFlash chip.
+ </para>
+ <para>
+ The +1g and -1g calibration points are included in each telemetry
+ frame and are part of the header extracted by ao-dumplog after flight.
+ Note that we always store and return raw ADC samples for each
+ sensor... nothing is permanently "lost" or "damaged" if the
+ calibration is poor.
+ </para>
+ </section>
+ </section>