+ <title>Configure Groundstation</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="configure-groundstation.png" width="3.1in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ Select this button and then select a TeleDongle Device from the list provided.
+ </para>
+ <para>
+ The first few lines of the dialog provide information about the
+ connected device, including the product name,
+ software version and hardware serial number. Below that are the
+ individual configuration entries.
+ </para>
+ <para>
+ Note that the TeleDongle itself doesn't save any configuration
+ data, the settings here are recorded on the local machine in
+ the Java preferences database. Moving the TeleDongle to
+ another machine, or using a different user account on the same
+ machine will cause settings made here to have no effect.
+ </para>
+ <para>
+ At the bottom of the dialog, there are three buttons:
+ </para>
+ <variablelist>
+ <varlistentry>
+ <term>Save</term>
+ <listitem>
+ <para>
+ This writes any changes to the
+ local Java preferences file. If you don't
+ press this button, any changes you make will be lost.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Reset</term>
+ <listitem>
+ <para>
+ This resets the dialog to the most recently saved values,
+ erasing any changes you have made.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Close</term>
+ <listitem>
+ <para>
+ This closes the dialog. Any unsaved changes will be
+ lost.
+ </para>
+ </listitem>
+ </varlistentry>
+ </variablelist>
+ <para>
+ The rest of the dialog contains the parameters to be configured.
+ </para>
+ <section>
+ <title>Frequency</title>
+ <para>
+ This configures the frequency to use for both telemetry and
+ packet command mode. Set this before starting any operation
+ involving packet command mode so that it will use the right
+ frequency. Telemetry monitoring mode also provides a menu to
+ change the frequency, and that menu also sets the same Java
+ preference value used here.
+ </para>
+ </section>
+ <section>
+ <title>Radio Calibration</title>
+ <para>
+ The radios in every Altus Metrum device are calibrated at the
+ factory to ensure that they transmit and receive on the
+ specified frequency. To change a TeleDongle's calibration,
+ you must reprogram the unit completely, so this entry simply
+ shows the current value and doesn't allow any changes.
+ </para>
+ </section>
+ </section>
+ <section>
+ <title>Flash Image</title>
+ <para>
+ This reprograms Altus Metrum devices with new
+ firmware. TeleMetrum v1.x, TeleDongle, TeleMini and TeleBT are
+ all reprogrammed by using another similar unit as a
+ programming dongle (pair programming). TeleMega, TeleMetrum v2
+ and EasyMini are all programmed directly over their USB ports
+ (self programming). Please read the directions for flashing
+ devices in the Updating Device Firmware chapter below.
+ </para>
+ </section>
+ <section>
+ <title>Fire Igniter</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="fire-igniter.png" width="1.2in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ This activates the igniter circuits in the flight computer to help
+ test recovery systems deployment. Because this command can operate
+ over the Packet Command Link, you can prepare the rocket as
+ for flight and then test the recovery system without needing
+ to snake wires inside the air-frame.
+ </para>
+ <para>
+ Selecting the 'Fire Igniter' button brings up the usual device
+ selection dialog. Pick the desired device. This brings up another
+ window which shows the current continuity test status for all
+ of the pyro channels.
+ </para>
+ <para>
+ Next, select the desired igniter to fire. This will enable the
+ 'Arm' button.
+ </para>
+ <para>
+ Select the 'Arm' button. This enables the 'Fire' button. The
+ word 'Arm' is replaced by a countdown timer indicating that
+ you have 10 seconds to press the 'Fire' button or the system
+ will deactivate, at which point you start over again at
+ selecting the desired igniter.
+ </para>
+ </section>
+ <section>
+ <title>Scan Channels</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="scan-channels.png" width="3.2in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ This listens for telemetry packets on all of the configured
+ frequencies, displaying information about each device it
+ receives a packet from. You can select which of the three
+ telemetry formats should be tried; by default, it only listens
+ for the standard telemetry packets used in v1.0 and later
+ firmware.
+ </para>
+ </section>
+ <section>
+ <title>Load Maps</title>
+ <informalfigure>
+ <mediaobject>
+ <imageobject>
+ <imagedata fileref="load-maps.png" width="5.2in" scalefit="1"/>
+ </imageobject>
+ </mediaobject>
+ </informalfigure>
+ <para>
+ Before heading out to a new launch site, you can use this to
+ load satellite images in case you don't have internet
+ connectivity at the site. This loads a fairly large area
+ around the launch site, which should cover any flight you're likely to make.
+ </para>
+ <para>
+ There's a drop-down menu of launch sites we know about; if
+ your favorites aren't there, please let us know the lat/lon
+ and name of the site. The contents of this list are actually
+ downloaded from our server at run-time, so as new sites are sent
+ in, they'll get automatically added to this list.
+ If the launch site isn't in the list, you can manually enter the lat/lon values
+ </para>
+ <para>
+ There are four different kinds of maps you can view; you can
+ select which to download by selecting as many as you like from
+ the available types:
+ <variablelist>
+ <varlistentry>
+ <term>Hybrid</term>
+ <listitem>
+ <para>
+ A combination of satellite imagery and road data. This
+ is the default view.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Satellite</term>
+ <listitem>
+ <para>
+ Just the satellite imagery without any annotation.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Roadmap</term>
+ <listitem>
+ <para>
+ Roads, political boundaries and a few geographic features.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Terrain</term>
+ <listitem>
+ <para>
+ Contour intervals and shading that show hills and
+ valleys.
+ </para>
+ </listitem>
+ </varlistentry>
+ </variablelist>
+ </para>
+ <para>
+ You can specify the range of zoom levels to download; smaller
+ numbers show more area with less resolution. The default
+ level, 0, shows about 3m/pixel. One zoom level change
+ doubles or halves that number.
+ </para>
+ <para>
+ The Tile Radius value sets how large an area around the center
+ point to download. Each tile is 512x512 pixels, and the
+ 'radius' value specifies how many tiles away from the center
+ will be downloaded. Specify a radius of 0 and you get only the
+ center tile. A radius of 1 loads a 3x3 grid, centered on the
+ specified location.
+ </para>
+ <para>
+ Clicking the 'Load Map' button will fetch images from Google
+ Maps; note that Google limits how many images you can fetch at
+ once, so if you load more than one launch site, you may get
+ some gray areas in the map which indicate that Google is tired
+ of sending data to you. Try again later.
+ </para>
+ </section>
+ <section>
+ <title>Monitor Idle</title>
+ <para>
+ This brings up a dialog similar to the Monitor Flight UI,
+ except it works with the altimeter in “idle” mode by sending
+ query commands to discover the current state rather than
+ listening for telemetry packets. Because this uses command
+ mode, it needs to have the TeleDongle and flight computer
+ callsigns match exactly. If you can receive telemetry, but
+ cannot manage to run Monitor Idle, then it's very likely that
+ your callsigns are different in some way.
+ </para>
+ </section>
+ </chapter>
+ <chapter>
+ <title>AltosDroid</title>
+ <para>
+ AltosDroid provides the same flight monitoring capabilities as
+ AltosUI, but runs on Android devices and is designed to connect
+ to a TeleBT receiver over Bluetooth™. AltosDroid monitors
+ telemetry data, logging it to internal storage in the Android
+ device, and presents that data in a UI the same way the 'Monitor
+ Flight' window does in AltosUI.
+ </para>
+ <para>
+ This manual will explain how to configure AltosDroid, connect
+ to TeleBT, operate the flight monitoring interface and describe
+ what the displayed data means.
+ </para>
+ <section>
+ <title>Installing AltosDroid</title>
+ <para>
+ AltosDroid is available from the Google Play store. To install
+ it on your Android device, open the Google Play Store
+ application and search for “altosdroid”. Make sure you don't
+ have a space between “altos” and “droid” or you probably won't
+ find what you want. That should bring you to the right page
+ from which you can download and install the application.
+ </para>
+ </section>
+ <section>
+ <title>Connecting to TeleBT</title>
+ <para>
+ Press the Android 'Menu' button or soft-key to see the
+ configuration options available. Select the 'Connect a device'
+ option and then the 'Scan for devices' entry at the bottom to
+ look for your TeleBT device. Select your device, and when it
+ asks for the code, enter '1234'.
+ </para>
+ <para>
+ Subsequent connections will not require you to enter that
+ code, and your 'paired' device will appear in the list without
+ scanning.
+ </para>
+ </section>
+ <section>
+ <title>Configuring AltosDroid</title>
+ <para>
+ The only configuration option available for AltosDroid is
+ which frequency to listen on. Press the Android 'Menu' button
+ or soft-key and pick the 'Select radio frequency' entry. That
+ brings up a menu of pre-set radio frequencies; pick the one
+ which matches your altimeter.
+ </para>
+ </section>
+ <section>
+ <title>AltosDroid Flight Monitoring</title>
+ <para>
+ AltosDroid is designed to mimic the AltosUI flight monitoring
+ display, providing separate tabs for each stage of your rocket
+ flight along with a tab containing a map of the local area
+ with icons marking the current location of the altimeter and
+ the Android device.
+ </para>
+ <section>
+ <title>Pad</title>
+ <para>
+ The 'Launch Pad' tab shows information used to decide when the
+ rocket is ready for flight. The first elements include red/green
+ indicators, if any of these is red, you'll want to evaluate
+ whether the rocket is ready to launch:
+ <variablelist>
+ <varlistentry>
+ <term>Battery Voltage</term>
+ <listitem>
+ <para>
+ This indicates whether the Li-Po battery
+ powering the TeleMetrum has sufficient charge to last for
+ the duration of the flight. A value of more than
+ 3.8V is required for a 'GO' status.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Apogee Igniter Voltage</term>
+ <listitem>
+ <para>
+ This indicates whether the apogee
+ igniter has continuity. If the igniter has a low
+ resistance, then the voltage measured here will be close
+ to the Li-Po battery voltage. A value greater than 3.2V is
+ required for a 'GO' status.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>Main Igniter Voltage</term>
+ <listitem>
+ <para>
+ This indicates whether the main
+ igniter has continuity. If the igniter has a low
+ resistance, then the voltage measured here will be close
+ to the Li-Po battery voltage. A value greater than 3.2V is
+ required for a 'GO' status.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>On-board Data Logging</term>
+ <listitem>
+ <para>
+ This indicates whether there is
+ space remaining on-board to store flight data for the
+ upcoming flight. If you've downloaded data, but failed
+ to erase flights, there may not be any space
+ left. TeleMetrum can store multiple flights, depending
+ on the configured maximum flight log size. TeleMini
+ stores only a single flight, so it will need to be
+ downloaded and erased after each flight to capture
+ data. This only affects on-board flight logging; the
+ altimeter will still transmit telemetry and fire
+ ejection charges at the proper times.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>GPS Locked</term>
+ <listitem>
+ <para>
+ For a TeleMetrum or TeleMega device, this indicates whether the GPS receiver is
+ currently able to compute position information. GPS requires
+ at least 4 satellites to compute an accurate position.
+ </para>
+ </listitem>
+ </varlistentry>
+ <varlistentry>
+ <term>GPS Ready</term>
+ <listitem>
+ <para>
+ For a TeleMetrum or TeleMega device, this indicates whether GPS has reported at least
+ 10 consecutive positions without losing lock. This ensures
+ that the GPS receiver has reliable reception from the
+ satellites.
+ </para>
+ </listitem>
+ </varlistentry>
+ </variablelist>
+ </para>
+ <para>
+ The Launchpad tab also shows the computed launch pad position
+ and altitude, averaging many reported positions to improve the
+ accuracy of the fix.
+ </para>
+ </section>
+ </section>
+ <section>
+ <title>Downloading Flight Logs</title>
+ <para>
+ AltosDroid always saves every bit of telemetry data it
+ receives. To download that to a computer for use with AltosUI,
+ simply remove the SD card from your Android device, or connect
+ your device to your computer's USB port and browse the files
+ on that device. You will find '.telem' files in the TeleMetrum
+ directory that will work with AltosUI directly.
+ </para>
+ </section>
+ </chapter>
+ <chapter>
+ <title>Using Altus Metrum Products</title>
+ <section>
+ <title>Being Legal</title>
+ <para>
+ First off, in the US, you need an <ulink url="http://www.altusmetrum.org/Radio/">amateur radio license</ulink> or
+ other authorization to legally operate the radio transmitters that are part
+ of our products.
+ </para>
+ </section>
+ <section>
+ <title>In the Rocket</title>
+ <para>
+ In the rocket itself, you just need a flight computer and
+ a single-cell, 3.7 volt nominal Li-Po rechargeable battery. An
+ 850mAh battery weighs less than a 9V alkaline battery, and will
+ run a TeleMetrum or TeleMega for hours.
+ A 110mAh battery weighs less than a triple A battery and is a good
+ choice for use with TeleMini.
+ </para>
+ <para>
+ By default, we ship flight computers with a simple wire antenna.
+ If your electronics bay or the air-frame it resides within is made
+ of carbon fiber, which is opaque to RF signals, you may prefer to
+ install an SMA connector so that you can run a coaxial cable to an
+ antenna mounted elsewhere in the rocket. However, note that the
+ GPS antenna is fixed on all current products, so you really want
+ to install the flight computer in a bay made of RF-transparent
+ materials if at all possible.
+ </para>
+ </section>
+ <section>
+ <title>On the Ground</title>
+ <para>
+ To receive the data stream from the rocket, you need an antenna and short
+ feed-line connected to one of our <ulink url="http://www.altusmetrum.org/TeleDongle/">TeleDongle</ulink> units. If possible, use an SMA to BNC
+ adapter instead of feedline between the antenna feedpoint and
+ TeleDongle, as this will give you the best performance. The
+ TeleDongle in turn plugs directly into the USB port on a notebook
+ computer. Because TeleDongle looks like a simple serial port, your computer
+ does not require special device drivers... just plug it in.
+ </para>
+ <para>
+ The GUI tool, AltosUI, is written in Java and runs across
+ Linux, Mac OS and Windows. There's also a suite of C tools
+ for Linux which can perform most of the same tasks.
+ </para>
+ <para>
+ Alternatively, a TeleBT attached with an SMA to BNC adapter at the
+ feed point of a hand-held yagi used in conjunction with an Android
+ device running AltosDroid makes an outstanding ground station.
+ </para>
+ <para>
+ After the flight, you can use the radio link to extract the more detailed data
+ logged in either TeleMetrum or TeleMini devices, or you can use a mini USB cable to plug into the
+ TeleMetrum board directly. Pulling out the data without having to open up
+ the rocket is pretty cool! A USB cable is also how you charge the Li-Po
+ battery, so you'll want one of those anyway... the same cable used by lots
+ of digital cameras and other modern electronic stuff will work fine.
+ </para>
+ <para>
+ If your rocket lands out of sight, you may enjoy having a hand-held
+ GPS receiver, so that you can put in a way-point for the last
+ reported rocket position before touch-down. This makes looking for
+ your rocket a lot like Geo-Caching... just go to the way-point and
+ look around starting from there. AltosDroid on an Android device
+ with GPS receiver works great for this, too!
+ </para>
+ <para>
+ You may also enjoy having a ham radio “HT” that covers the 70cm band... you
+ can use that with your antenna to direction-find the rocket on the ground
+ the same way you can use a Walston or Beeline tracker. This can be handy
+ if the rocket is hiding in sage brush or a tree, or if the last GPS position
+ doesn't get you close enough because the rocket dropped into a canyon, or
+ the wind is blowing it across a dry lake bed, or something like that... Keith
+ currently uses a Yaesu VX-7R, Bdale has a Baofung UV-5R
+ which isn't as nice, but was a whole lot cheaper.
+ </para>
+ <para>
+ So, to recap, on the ground the hardware you'll need includes:
+ <orderedlist inheritnum='inherit' numeration='arabic'>
+ <listitem>
+ <para>
+ an antenna and feed-line or adapter
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ a TeleDongle
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ a notebook computer
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ optionally, a hand-held GPS receiver
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ optionally, an HT or receiver covering 435 MHz
+ </para>
+ </listitem>
+ </orderedlist>
+ </para>
+ <para>
+ The best hand-held commercial directional antennas we've found for radio
+ direction finding rockets are from
+ <ulink url="http://www.arrowantennas.com/" >
+ Arrow Antennas.
+ </ulink>
+ The 440-3 and 440-5 are both good choices for finding a
+ TeleMetrum- or TeleMini- equipped rocket when used with a suitable
+ 70cm HT. TeleDongle and an SMA to BNC adapter fit perfectly
+ between the driven element and reflector of Arrow antennas.
+ </para>
+ </section>
+ <section>
+ <title>Data Analysis</title>
+ <para>
+ Our software makes it easy to log the data from each flight, both the
+ telemetry received during the flight itself, and the more
+ complete data log recorded in the flash memory on the altimeter
+ board. Once this data is on your computer, our post-flight tools make it
+ easy to quickly get to the numbers everyone wants, like apogee altitude,
+ max acceleration, and max velocity. You can also generate and view a
+ standard set of plots showing the altitude, acceleration, and
+ velocity of the rocket during flight. And you can even export a TeleMetrum data file
+ usable with Google Maps and Google Earth for visualizing the flight path
+ in two or three dimensions!
+ </para>
+ <para>
+ Our ultimate goal is to emit a set of files for each flight that can be
+ published as a web page per flight, or just viewed on your local disk with
+ a web browser.
+ </para>
+ </section>
+ <section>
+ <title>Future Plans</title>
+ <para>
+ We've designed a simple GPS based radio tracker called TeleGPS.
+ If all goes well, we hope to introduce this in the first
+ half of 2014.
+ </para>
+ <para>
+ We have designed and prototyped several “companion boards” that
+ can attach to the companion connector on TeleMetrum and TeleMega
+ flight computers to collect more data, provide more pyro channels,
+ and so forth. We do not yet know if or when any of these boards
+ will be produced in enough quantity to sell. If you have specific
+ interests for data collection or control of events in your rockets
+ beyond the capabilities of our existing productions, please let
+ us know!
+ </para>
+ <para>
+ Because all of our work is open, both the hardware designs and the
+ software, if you have some great idea for an addition to the current
+ Altus Metrum family, feel free to dive in and help! Or let us know
+ what you'd like to see that we aren't already working on, and maybe
+ we'll get excited about it too...
+ </para>
+ <para>
+ Watch our
+ <ulink url="http://altusmetrum.org/">web site</ulink> for more news
+ and information as our family of products evolves!
+ </para>
+ </section>
+ </chapter>
+ <chapter>
+ <title>Altimeter Installation Recommendations</title>
+ <para>
+ Building high-power rockets that fly safely is hard enough. Mix
+ in some sophisticated electronics and a bunch of radio energy
+ and some creativity and/or compromise may be required. This chapter
+ contains some suggestions about how to install Altus Metrum
+ products into a rocket air-frame, including how to safely and
+ reliably mix a variety of electronics into the same air-frame.
+ </para>
+ <section>
+ <title>Mounting the Altimeter</title>
+ <para>
+ The first consideration is to ensure that the altimeter is
+ securely fastened to the air-frame. For most of our products, we
+ prefer nylon standoffs and nylon screws; they're good to at least 50G
+ and cannot cause any electrical issues on the board. Metal screws
+ and standoffs are fine, too, just be careful to avoid electrical
+ shorts! For TeleMini v1.0, we usually cut small pieces of 1/16 inch
+ balsa to fit
+ under the screw holes, and then take 2x56 nylon screws and
+ screw them through the TeleMini mounting holes, through the
+ balsa and into the underlying material.
+ </para>
+ <orderedlist inheritnum='inherit' numeration='arabic'>
+ <listitem>
+ <para>
+ Make sure accelerometer-equipped products like TeleMetrum and
+ TeleMega are aligned precisely along the axis of
+ acceleration so that the accelerometer can accurately
+ capture data during the flight.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Watch for any metal touching components on the
+ board. Shorting out connections on the bottom of the board
+ can cause the altimeter to fail during flight.
+ </para>
+ </listitem>
+ </orderedlist>
+ </section>
+ <section>
+ <title>Dealing with the Antenna</title>