- <section>
- <title>Radio Frequency</title>
- <para>
- The radio frequency is synthesized from a clock based on the 48 Mhz
- crystal on the board. The actual frequency of this oscillator must be
- measured to generate a calibration constant. While our GFSK modulation
- bandwidth is wide enough to allow boards to communicate even when
- their oscillators are not on exactly the same frequency, performance
- is best when they are closely matched.
- Radio frequency calibration requires a calibrated frequency counter.
- Fortunately, once set, the variation in frequency due to aging and
- temperature changes is small enough that re-calibration by customers
- should generally not be required.
- </para>
- <para>
- To calibrate the radio frequency, connect the UHF antenna port to a
- frequency counter, set the board to 434.550MHz, and use the 'C'
- command to generate a CW carrier. Wait for the transmitter temperature
- to stabilize and the frequency to settle down.
- Then, divide 434.550 Mhz by the
- measured frequency and multiply by the current radio cal value show
- in the 'c s' command. For an unprogrammed board, the default value
- is 1186611. Take the resulting integer and program it using the 'c f'
- command. Testing with the 'C' command again should show a carrier
- within a few tens of Hertz of the intended frequency.
- As with all 'c' sub-commands, follow this with a 'c w' to write the
- change to the parameter block in the on-board DataFlash chip.
- </para>
- <para>
- when the radio calibration value is changed, the radio
- frequency value is reset to the same value, so you'll need
- to recompute and reset the radio frequency value using the
- new radio calibration value.
- </para>
- </section>
- <section>
- <title>TeleMetrum Accelerometer</title>
- <para>
- The TeleMerum accelerometer we use has its own 5 volt power supply and
- the output must be passed through a resistive voltage divider to match
- the input of our 3.3 volt ADC. This means that unlike the barometric
- sensor, the output of the acceleration sensor is not ratiometric to
- the ADC converter, and calibration is required. We also support the
- use of any of several accelerometers from a Freescale family that
- includes at least +/- 40g, 50g, 100g, and 200g parts. Using gravity,
- a simple 2-point calibration yields acceptable results capturing both
- the different sensitivities and ranges of the different accelerometer
- parts and any variation in power supply voltages or resistor values
- in the divider network.
- </para>
- <para>
- To calibrate the acceleration sensor, use the 'c a 0' command. You
- will be prompted to orient the board vertically with the UHF antenna
- up and press a key, then to orient the board vertically with the
- UHF antenna down and press a key.
- As with all 'c' sub-commands, follow this with a 'c w' to write the
- change to the parameter block in the on-board DataFlash chip.
- </para>
- <para>
- The +1g and -1g calibration points are included in each telemetry
- frame and are part of the header extracted by ao-dumplog after flight.
- Note that we always store and return raw ADC samples for each
- sensor... nothing is permanently "lost" or "damaged" if the
- calibration is poor.
- </para>
- <para>
- In the unlikely event an accel cal that goes badly, it is possible
- that TeleMetrum may always come up in 'pad mode' and as such not be
- listening to either the USB or radio interfaces. If that happens,
- there is a special hook in the firmware to force the board back
- in to 'idle mode' so you can re-do the cal. To use this hook, you
- just need to ground the SPI clock pin at power-on. This pin is
- available as pin 2 on the 8-pin companion connector, and pin 1 is
- ground. So either carefully install a fine-gauge wire jumper
- between the two pins closest to the index hole end of the 8-pin
- connector, or plug in the programming cable to the 8-pin connector
- and use a small screwdriver or similar to short the two pins closest
- to the index post on the 4-pin end of the programming cable, and
- power up the board. It should come up in 'idle mode' (two beeps).
- </para>
- </section>
- </section>
- <section>
- <title>Updating Device Firmware</title>
- <para>
- The big conceptual thing to realize is that you have to use a
- TeleDongle as a programmer to update a TeleMetrum or TeleMini,
- and a TeleMetrum or other TeleDongle to program the TeleDongle
- Due to limited memory resources in the cc1111, we don't support
- programming directly over USB.
- </para>
- <para>
- You may wish to begin by ensuring you have current firmware images.
- These are distributed as part of the AltOS software bundle that
- also includes the AltosUI ground station program. Newer ground
- station versions typically work fine with older firmware versions,
- so you don't need to update your devices just to try out new
- software features. You can always download the most recent
- version from <ulink url="http://www.altusmetrum.org/AltOS/"/>.
- </para>
- <para>
- We recommend updating the altimeter first, before updating TeleDongle.
- </para>
- <section>
- <title>Updating TeleMetrum Firmware</title>
- <orderedlist inheritnum='inherit' numeration='arabic'>
- <listitem>
- Find the 'programming cable' that you got as part of the starter
- kit, that has a red 8-pin MicroMaTch connector on one end and a
- red 4-pin MicroMaTch connector on the other end.
- </listitem>
- <listitem>
- Take the 2 screws out of the TeleDongle case to get access
- to the circuit board.
- </listitem>
- <listitem>
- Plug the 8-pin end of the programming cable to the
- matching connector on the TeleDongle, and the 4-pin end to the
- matching connector on the TeleMetrum.
- Note that each MicroMaTch connector has an alignment pin that
- goes through a hole in the PC board when you have the cable
- oriented correctly.
- </listitem>
- <listitem>
- Attach a battery to the TeleMetrum board.
- </listitem>
- <listitem>
- Plug the TeleDongle into your computer's USB port, and power
- up the TeleMetrum.
- </listitem>
- <listitem>
- Run AltosUI, and select 'Flash Image' from the File menu.
- </listitem>
- <listitem>
- Pick the TeleDongle device from the list, identifying it as the
- programming device.
- </listitem>
- <listitem>
- Select the image you want put on the TeleMetrum, which should have a
- name in the form telemetrum-v1.1-1.0.0.ihx. It should be visible
- in the default directory, if not you may have to poke around
- your system to find it.
- </listitem>
- <listitem>
- Make sure the configuration parameters are reasonable
- looking. If the serial number and/or RF configuration
- values aren't right, you'll need to change them.
- </listitem>
- <listitem>
- Hit the 'OK' button and the software should proceed to flash
- the TeleMetrum with new firmware, showing a progress bar.
- </listitem>
- <listitem>
- Confirm that the TeleMetrum board seems to have updated ok, which you
- can do by plugging in to it over USB and using a terminal program
- to connect to the board and issue the 'v' command to check
- the version, etc.
- </listitem>
- <listitem>
- If something goes wrong, give it another try.
- </listitem>
- </orderedlist>
- </section>
- <section>
- <title>Updating TeleMini Firmware</title>
- <orderedlist inheritnum='inherit' numeration='arabic'>
- <listitem>
- You'll need a special 'programming cable' to reprogram the
- TeleMini. It's available on the Altus Metrum web store, or
- you can make your own using an 8-pin MicroMaTch connector on
- one end and a set of four pins on the other.
- </listitem>
- <listitem>
- Take the 2 screws out of the TeleDongle case to get access
- to the circuit board.
- </listitem>
- <listitem>
- Plug the 8-pin end of the programming cable to the matching
- connector on the TeleDongle, and the 4-pins into the holes
- in the TeleMini circuit board. Note that the MicroMaTch
- connector has an alignment pin that goes through a hole in
- the PC board when you have the cable oriented correctly, and
- that pin 1 on the TeleMini board is marked with a square pad
- while the other pins have round pads.
- </listitem>
- <listitem>
- Attach a battery to the TeleMini board.
- </listitem>
- <listitem>
- Plug the TeleDongle into your computer's USB port, and power
- up the TeleMini
- </listitem>
- <listitem>
- Run AltosUI, and select 'Flash Image' from the File menu.
- </listitem>
- <listitem>
- Pick the TeleDongle device from the list, identifying it as the
- programming device.
- </listitem>
- <listitem>
- Select the image you want put on the TeleMini, which should have a
- name in the form telemini-v1.0-1.0.0.ihx. It should be visible
- in the default directory, if not you may have to poke around
- your system to find it.
- </listitem>
- <listitem>
- Make sure the configuration parameters are reasonable
- looking. If the serial number and/or RF configuration
- values aren't right, you'll need to change them.
- </listitem>
- <listitem>
- Hit the 'OK' button and the software should proceed to flash
- the TeleMini with new firmware, showing a progress bar.
- </listitem>
- <listitem>
- Confirm that the TeleMini board seems to have updated ok, which you
- can do by configuring it over the RF link through the TeleDongle, or
- letting it come up in "flight" mode and listening for telemetry.
- </listitem>
- <listitem>
- If something goes wrong, give it another try.
- </listitem>
- </orderedlist>
- </section>
- <section>
- <title>Updating TeleDongle Firmware</title>
- <para>
- Updating TeleDongle's firmware is just like updating TeleMetrum or TeleMini
- firmware, but you use either a TeleMetrum or another TeleDongle as the programmer.
- </para>
- <orderedlist inheritnum='inherit' numeration='arabic'>
- <listitem>
- Find the 'programming cable' that you got as part of the starter
- kit, that has a red 8-pin MicroMaTch connector on one end and a
- red 4-pin MicroMaTch connector on the other end.
- </listitem>
- <listitem>
- Find the USB cable that you got as part of the starter kit, and
- plug the "mini" end in to the mating connector on TeleMetrum or TeleDongle.
- </listitem>
- <listitem>
- Take the 2 screws out of the TeleDongle case to get access
- to the circuit board.
- </listitem>
- <listitem>
- Plug the 8-pin end of the programming cable to the
- matching connector on the programmer, and the 4-pin end to the
- matching connector on the TeleDongle.
- Note that each MicroMaTch connector has an alignment pin that
- goes through a hole in the PC board when you have the cable
- oriented correctly.
- </listitem>
- <listitem>
- Attach a battery to the TeleMetrum board if you're using one.
- </listitem>
- <listitem>
- Plug both the programmer and the TeleDongle into your computer's USB
- ports, and power up the programmer.
- </listitem>
- <listitem>
- Run AltosUI, and select 'Flash Image' from the File menu.
- </listitem>
- <listitem>
- Pick the programmer device from the list, identifying it as the
- programming device.
- </listitem>
- <listitem>
- Select the image you want put on the TeleDongle, which should have a
- name in the form teledongle-v0.2-1.0.0.ihx. It should be visible
- in the default directory, if not you may have to poke around
- your system to find it.
- </listitem>
- <listitem>
- Make sure the configuration parameters are reasonable
- looking. If the serial number and/or RF configuration
- values aren't right, you'll need to change them. The TeleDongle
- serial number is on the "bottom" of the circuit board, and can
- usually be read through the translucent blue plastic case without
- needing to remove the board from the case.
- </listitem>