<a href="v1.0/telemega-v1.0-top.jpg"> <img src="v1.0/telemega-v1.0-top-thumb.jpg"></a>
<a href="v1.0/telemega-v1.0-bottom.jpg"> <img src="v1.0/telemega-v1.0-bottom-thumb.jpg"></a>
<a href="v1.0/telemega-v1.0-top.jpg"> <img src="v1.0/telemega-v1.0-top-thumb.jpg"></a>
<a href="v1.0/telemega-v1.0-bottom.jpg"> <img src="v1.0/telemega-v1.0-bottom-thumb.jpg"></a>
including angle from vertical (for safety in staging and air start flights).
* 70cm ham-band transceiver for telemetry downlink
* Barometric pressure sensor good to 100k feet MSL
including angle from vertical (for safety in staging and air start flights).
* 70cm ham-band transceiver for telemetry downlink
* Barometric pressure sensor good to 100k feet MSL
* 3-axis 16-g accelerometer for gyro calibration
* 3-axis 2000 deg/sec gyros
* 3-axis magnetic sensor
* On-board, integrated GPS receiver
* On-board non-volatile memory for flight data storage
* 3-axis 16-g accelerometer for gyro calibration
* 3-axis 2000 deg/sec gyros
* 3-axis magnetic sensor
* On-board, integrated GPS receiver
* On-board non-volatile memory for flight data storage
* USB for power, configuration, and data recovery
* Integrated support for LiPo rechargeable batteries
* User choice of pyro battery configuration, can use primary LiPo or any
* USB for power, configuration, and data recovery
* Integrated support for LiPo rechargeable batteries
* User choice of pyro battery configuration, can use primary LiPo or any
- * [Winbond W25Q64CV](http://www.winbond.com/hq/enu/ProductAndSales/ProductLines/FlashMemory/SerialFlash/W25Q64CV.htm) serial flash memory
- * [u-blox](http://www.u-blox.com/) MAX-7Q GPS receiver
+ * [Winbond W25Q64FV](http://www.winbond.com/hq/product/code-storage-flash-memory/serial-nor-flash/?__locale=en&partNo=W25Q64FV) serial flash memory
+ * [u-blox](http://www.u-blox.com/) MAX-8Q GPS receiver
* on-board TaoGlas passive patch antenna
* async serial interface
* Measurement Specialties [MS5607](http://www.meas-spec.com/product/t_product.aspx?id=8499) Micro Altimeter Module
* Wide range — 120kPa to 1kPa (approximately -1500m to 31000m)
* High precision — 2.4Pa resolution (approximately 20cm at sea level)
* Factory calibrated.
* on-board TaoGlas passive patch antenna
* async serial interface
* Measurement Specialties [MS5607](http://www.meas-spec.com/product/t_product.aspx?id=8499) Micro Altimeter Module
* Wide range — 120kPa to 1kPa (approximately -1500m to 31000m)
* High precision — 2.4Pa resolution (approximately 20cm at sea level)
* Factory calibrated.
- * Freescale [MMA6555](http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=MMA65xx&fsrch=1&sr=1) Single Axis SPI Intertial Sensor
- * +- 105g full-scale
- * on-chip 12-bit digitizer
- * Invensense [MPU-6000](http://invensense.com/mems/gyro/mpu6050.html) Six-Axis MEMS Motion Tracking Device
+ * Analog Devices [ADXL375](https://www.analog.com/en/products/adxl375.html) 3-Axis Digital MEMS Accelerometer
+ * +- 200g full-scale
+ * on-chip digitizer
+ * Bosch [BMX160](https://www.bosch-sensortec.com/products/motion-sensors/absolute-orientation-sensors/absolute-orientation-sensors-bmx160.html) Absolute Orientation Sensor
* Software Features
* Written mostly in C with some ARM assembler
* Runs from on-chip flash, uses on-chip RAM, stores flight data to serial flash
* USB serial emulation for "console" interface
* Tools Used
* Software Features
* Written mostly in C with some ARM assembler
* Runs from on-chip flash, uses on-chip RAM, stores flight data to serial flash
* USB serial emulation for "console" interface
* Tools Used
* Licenses
* The hardware is licensed under the [TAPR](http://www.tapr.org) [Open Hardware License](http://www.tapr.org/ohl.html)
* The software is licensed [GPL version 2](http://www.gnu.org/licenses/old-licenses/gpl-2.0.html)
* Licenses
* The hardware is licensed under the [TAPR](http://www.tapr.org) [Open Hardware License](http://www.tapr.org/ohl.html)
* The software is licensed [GPL version 2](http://www.gnu.org/licenses/old-licenses/gpl-2.0.html)
An outline of the board with drill hole locations is available in
[pdf](../Documents/telemega-outline.pdf) format.
An outline of the board with drill hole locations is available in
[pdf](../Documents/telemega-outline.pdf) format.
[git.gag.com](http://git.gag.com) in the project
[hw/telemega](http://git.gag.com/?p=hw/telemega;a=summary).
For those who don't have ready access to the gEDA suite, here are pdf snapshots
[git.gag.com](http://git.gag.com) in the project
[hw/telemega](http://git.gag.com/?p=hw/telemega;a=summary).
For those who don't have ready access to the gEDA suite, here are pdf snapshots
-* [schematic](v1.0/telemega-sch.pdf)
-* [pcb artwork](v1.0/telemega-pcb.pdf)
-* [bill of materials](v1.0/partslist.csv)
+* [schematic](v3.0/telemega-sch.pdf)
+* [pcb artwork](v3.0/telemega-pcb.pdf)
+* [bill of materials](v3.0/partslist.csv)