1 # Altus Metrum Units Constructed
3 This page contains Bdale's notes about each unit of [TeleMetrum](TeleMetrum/)
4 and [TeleDongle](TeleDongle/) assembled to date.
8 Full load of v0.1 PCB, two cuts and jumps to rewire P1_2 to be SPI memory
9 chip select, R14 and R15 loaded with 56k, 10k tacked from each to
10 ground. R17 replaced with short circuit, R18 removed.
12 Installed in Bdale's Vertical Assault. First unit to be flown on
13 2009.04.19, on a Cesaroni J335.
15 Successfully flew Bdale's rebuilt Horizon dual-deploy at Hudson Ranch on
16 2009.07.18 with a MAWD as backup. The first dual-deploy flight with a TM
17 board in control of ejection charges!
21 Full load of v0.1 PCB, two cuts and jumps to rewire P1_2 to be SPI memory
22 chip select, R14 and R15 loaded with 56k, 10k tacked from each to
25 Delivered to Keith Packard for firmware development and use. Flown twice
26 on 10 May 2008 in Keith's Grappler to about 45m on Estes D12-3 motors.
28 Flew in Keith's Little Dog Dual Deploy at Mile High Mayhem as a payload. The
29 ascent was pretty but the rocket failed to deploy and lawn-darted. The battery
30 and screw terminal block connectors got more or less torn off, but the rest
31 of the board survived and good data was recovered from the flight.
33 Repaired by Bdale, sent back to Keith on 7 July 2009. Keith reported the
34 baro sensor as flakey, it was replaced in October 2009 prior to
39 Full load of v0.1 PCB on 2009.04.22, two cuts and jumps to rewire P1_2
40 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked
43 Installed in Bdale's Vertical Assault after sn 1 moved to Horizon, but never
46 Pulled and given to Keith to take home from Mayhem.
48 Lost in Keith's Nike which was lost for a while after an apparently nominal
49 flight in June 2009 at Brothers, Oregon. Rocket was later found and this unit
50 is reportedly still in good condition.
54 Full load of v0.1 PCB on 2009.04.22, two cuts and jumps to rewire P1_2
55 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked
58 Installed in Robert's Lil Nuke.
60 Lost at Hudson Ranch 2009.07.18 when we forgot to tape the nose cone on and
61 both it and the electronics sled came out at apogee and were not recovered.
65 Partial "ground" load of v0.1 PCB on 2009.04.23 plus beeper and serial
66 connector for use as TeleDongle or for TeleTerra prototype.
70 Keith added acrylic LED light pipes and a LiPo for use in RDF after flight.
74 Partial "ground" load of v0.1 PCB on 2009.04.23 for use as TeleDongle.
78 Keith added acrylic LED light pipes and a LiPo for use in RDF after flight.
82 Full load of v0.1 PCB on 2009.08.08, two cuts and jumps to rewire P1_2
83 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked
86 Pulled from Vertical Assault (never flew there) and taken to Keith in Japan
87 in October 2009 as replacement.
91 Full load of v0.1 PCB on 2009.08.08, two cuts and jumps to rewire P1_2
92 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked
95 Delivered to Keith in early November 2009.
99 Full load of v0.1 PCB on 2009.08.15, two cuts and jumps to rewire P1_2
100 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked
103 Installed in Bdale's Trick-o-Treat 98mm airframe.
107 Full load of v0.1 PCB on 2009.08.15, two cuts and jumps to rewire P1_2
108 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked
111 Installed in Robert's Lil Nuke.
115 Full load of v0.1 PCB on 2009.08.15, two cuts and jumps to rewire P1_2
116 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked
117 from each to ground. Accelerometer loaded is MMA2204EG 100G unit!
119 In G-Spot, this accelerometer recorded 52.8 gee acceleration on a
120 Cesaroni pro29 H399 reload at NCR Oktoberfest 2009!
122 Beeper failed after a hard landing, replaced 2010.02.06.
126 Full load of v0.1 PCB on 2009.11.05, two cuts and jumps to rewire P1_2
127 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked
128 from each to ground. Accelerometer loaded is MMA2204EG 100G unit!
132 Full load of v0.1 PCB on 2009.11.05, two cuts and jumps to rewire P1_2
133 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked
136 Modified 2009.11.20 to:
138 * use TC1055-3.3VCT713 100ma regulator proposed for v0.2
139 * route 3.3V instead of v_lipo to the serial connector for SkyTraq GPS
140 * use v_lipo for pyro voltage instead of 5V with 1000uF capacitor
141 * added 100uF 1206 capacitor on 3.3V rail
143 In this configuration, flew two textbook perfect flights on 2009.11.21 at
144 Hudson Ranch in Trick-O-Treat on J motors.
146 Modified 2011.11.13 to:
148 * test ADXL78 accelerometer functionality for v1.2 build
149 * use 3.3k instead of 10k for R2 and R3, to eliminate power-on pyro glitching
153 Full load of v0.1 PCB on 2009.11.05, two cuts and jumps to rewire P1_2
154 to be SPI memory chip select, R14 and R15 loaded with 100k, 27k tacked
159 * R10 changed to 27k to allow keithp to test use of 1.25V ADC internal
160 reference with the accelerometer
162 Delivered to keithp on 2010.10.19.
164 Modifed by keithp on 2011.03.30 to have 3.3V on the serial connector power pin.
168 Partial "ground" load of v0.1 PCB on 2009.11.18 for use as TeleDongle.
172 Partial "ground" load of v0.1 PCB on 2009.11.18 for use as TeleDongle.
176 Full load of TeleMini v0.1 PCBs on 2011.03.07. Minor variations due to
177 parts availability, as follows:
179 * sn 17-18 have TXC oscillators, sn 19-21 have Abracom
180 * sn 21 is missing the dual LED
184 Full load of TeleTerra v0.1 PCBs on 2010.10.31
188 Full load of TeleNano v0.1 PCBs on 201103.09. sn 27 has TXC oscillator, all
189 others have Abracom, no other significant variations.
193 Full load of TeleMini v0.2 PCBs on 2011.05.04.
197 Full load of TeleScience v0.1 PCBs on 2011.05.05.
201 Full load of TeleBT v0.1 PCBs on 2011.05.06.
205 Full load of TelePyro v0.1 PCBs on 2011.09.20, except only sn 39 and 40
206 have magnetic sensors since I only have two samples of the now-obsolete part.
210 Full load of TeleScience v0.1 PCBs on 2011.09.22.
214 Full load of TeleTerra v0.2 PCBs on 2011.10.23.
218 Full load of TeleShield v0.1 PCBs on 2012.01.03, using 3.15V reset controller
219 and the less-good crystals.
223 Full load of TeleMetrum v0.2 PCB on 2010.01.09, with 100g accel and screw
226 Installed in G-Spot on 2010.02.06.
230 Full load of TeleMetrum v0.2 PCB on 2010.01.09, with 50g accel and Tyco header.
232 Went home with Keith from LCA 2010 in Wellington.
236 Full load of TeleMetrum v0.2 PCB on 2010.01.09, with 40g accel and screw
241 Prototypes of TeleMetrum v1.1 loaded with the newer Venus 638 chips for
242 evalutation, loaded as part of the production v1.1 run by
243 [Advanced Circuits](http://4pcb.com), received 2011.01.06.
247 Full load of TeleBT v0.2 PCBs on 2012.01.07.
251 Full load of TeleShield v0.1 PCBs on 2012.01.13.
255 MegaMetrum v0.1 PCBs on 2012.03.31, with 2 megabyte flash parts and no
260 TeleFire v0.1 PCB built by Keith on 2012.08.23.
264 TeleLCO v0.1 PCB built by Keith on 2012.08.26.
268 MegaMetrum v0.1 PCBs on 2012.08.28.
272 TeleBT v0.3 2012.12.19.
276 MegaDongle v0.2 2012.12.27.
280 TeleScience v0.2 2013.01.12.
284 TeleGPS v0.1 2013.03.20
288 TeleMega v0.3 2013.05.07. sn 85 has cc1125, the others have cc1120.
292 EasyMini v0.1 2013.05.19.
296 TeleMini v1.1 2013.05.22.
300 TeleMetrum v1.9 2013.08.27
304 TeleMega v0.4 P 2013.08.28
308 TeleMini v1.1 2013.08.25. From Phoenix panel.
312 TeleMini v1.1 2013.09.15. From Phoenix panel.
316 First production run of 108 pieces of TeleDongle v0.2 by
317 [Advanced Circuits](http://4pcb.com), received 2010.02.25.
321 First production run of 54 pieces of TeleMetrum v1.0 by
322 [Advanced Circuits](http://4pcb.com), received 2010.04.08.
326 Production run of 105 pieces of TeleMetrum v1.1 by
327 [Advanced Circuits](http://4pcb.com), received 2011.01.06.
331 Production run of 324 pieces of TeleDongle v0.2 by
332 [Advanced Circuits](http://4pcb.com), received 2011.03.21.
336 Production run of 144 pieces of TeleMini v1.0 by
337 [Advanced Circuits](http://4pcb.com), received 2011.07.25.
341 Production run of 107 pieces of TeleMetrum v1.2 by
342 [Advanced Circuits](http://4pcb.com), received 2011.12.15.
346 Production run of 108 pieces of TeleMetrum v1.2b by
347 [Advanced Circuits](http://4pcb.com), received 2012.10.29.
351 Production run of 120 pieces of TeleBT v1.0 by
352 [Advanced Circuits](http://4pcb.com), received 2013.04.08. All above
353 approximately sn 1050 were lost in the fire.
357 Production run of 120 pieces of TeleBT v1.1 by
358 [Advanced Circuits](http://4pcb.com), received 2013.08.22. This batch
359 later determined to have been built with "suspect" TI cc1111 chips.
363 Production run of 24 pieces of EasyMini v1.0 by
364 keithp. Build started 2013.10.05
368 Production run of 50 pieces of TeleMega v1.0 by
369 [Advanced Circuits](http://4pcb.com), received 2013.12.09.
373 TeleMini v1.1 from phoenix panel
377 Production run of 6 EasyMini v1.0 by keithp
381 Production run of 108 pieces of TeleMetrum v2.0 by
382 [Advanced Circuits](http://4pcb.com), received 2014.01.24.
386 Production run of 216 pieces of TeleDongle v0.2b byy
387 [Advanced Circuits](http://4pcb.com), received 2014.01.27. This batch
388 later determined to have been built with "suspect" TI cc1111 chips.
392 Production run of 9 EasyMini v1.0 by keithp 2014.01.30
396 Production run of 9 EasyMini v1.0 by keithp. 2014.02.04
400 Production run of 50 pieces of TeleMega v1.0 by
401 [Advanced Circuits](http://4pcb.com), received 2014.01.13.
405 Prototype build of 3 TeleGPS v0.3 by Bdale 2014.03.11.
409 Production run of 200 pieces of EasyMini v1.0 by
410 [Advanced Circuits](http://4pcb.com), received 2014.04.02.
414 Prototype build of 3 USBrelay v0.1 by Bdale 2014.05.07.
418 Prototype build of 3 FCtester v0.1 by Bdale 2014.05.11.
422 Prototype build of 3 EasyMega v0.1 by Bdale 2014.05.14
426 Production run of 108 pieces of TeleGPS v1.0 by
427 [Advanced Circuits](http://4pcb.com), received 2014.05.21.
431 Build 2 TeleFire v0.2 by Keith 2014.07.12
435 Production run of 100 pieces of EasyMega v1.0 by
436 [Advanced Circuits](http://4pcb.com), received 2014.08.14.
440 Prototype build of 3 TeleDongle v1.9 by Keithp 2014.11.06
444 Production run of 216 pieces of TeleMetrum v2.0b by
445 [Advanced Circuits](http://4pcb.com), received 2014.11.26.
449 Production run of 100 pieces of TeleMega v1.0b by
450 [Advanced Circuits](http://4pcb.com), received 2014.12.06.
454 Prototype build of 3 USBtrng v2.0 by Keithp 2015.01.25
458 Prototype build of 3 TeleBT v2.0 by bdale 2015.01.29
462 Production run of 108 pieces of TeleDongle v3.0 by
463 [Advanced Circuits](http://4pcb.com), received 2015.05.04.
467 Production run of 12 pieces of TeleMini v1.0 by keithp 2015.02.13
471 Prototype built of 12 USBtrng v3.0 by keithp 2015.02.22
475 Production run of 126 pieces of TeleBT v3.0 by
476 [Advanced Circuits](http://4pcb.com), received 2015.07.16.
480 Production run of 250 pieces of TeleDongle v3.0 by
481 [Advanced Circuits](http://4pcb.com), received 2015.10.21.
485 Prototype run of 3 pieces of TeleFireTwo v0.1 by keithp 2015.12.16
489 Prototype run of 3 pieces of TeleLCOTwo v0.1 by keithp 2015.12.16
493 Production run of 108 pieces of TeleGPS v1.0 by
494 [Advanced Circuits](http://4pcb.com), received 2016.01.06.
498 Production run of 100 pieces of TeleMega v2.0 by
499 [Advanced Circuits](http://4pcb.com), received 2016.01.06.
503 Production run of 2 pieces of TeleMini v1.0 by
504 keithp, built 2016.01.16
508 Production run of 260 pieces of EasyMini v1.0 by
509 [Advanced Circuits](http://4pcb.com), received 2016.01.26.
513 Prototype run of 3 TeleLCOTwo by
514 keithp, built 2016.04.05
518 Prototype run of 2 TeleFireTwo v0.2 by
519 keithp, built 2016.04.06
523 Prototype run of 4 TeleFireTwo v1.1 by
524 keithp, built 2016.06.12
528 Production run of 100 pieces of TeleMega v2.0 by
529 [Advanced Circuits](http://4pcb.com), received 2016.12.16.
533 Production run of 126 pieces of TeleMetrum v2.0b by
534 [Advanced Circuits](http://4pcb.com), received 2017.02.26.
538 Prototype build of 3 pieces of TeleGPS v2.0 by Bdale on 2017.04.13.
542 Prototype build of 3 pieces of TeleFireTwo v1.0 by Bdale on 2017.04.18.
546 Production run of 50 TeleMini v3.0 by
547 [Seeed Studios](https://www.seeedstudio.com/), received 2017.04.17.
551 Prototype build of 3 pieces of TeleBT v4.0 beta 1 by Bdale on 2017.04.25.
555 Production run of 250 pieces of TeleBT v4.0 by
556 [Advanced Circuits](http://4pcb.com), received 2017.07.21.
560 Errant TeleDongle v3.0 found in Bdale's collection.
564 Production run of 250 pieces of TeleGPS v2.0 by
565 [Advanced Circuits](http://4pcb.com), received 2017.09.16.
569 Production run of 250 pieces of TeleMega v3.0 by
570 [Advanced Circuits](http://4pcb.com), received 2017.11.30.
574 Production run of 500 pieces of EasyMini v2.0 by
575 [Advanced Circuits](http://4pcb.com), received 2017.12.19.
579 Production run of 198 pieces of TeleMetrum v2.0b by
580 [Advanced Circuits](http://4pcb.com), received 2018.03.10.
584 Hand build of 4 pieces of TeleLCO v2.0 by Bdale on 2017.05.27.
588 Hand build of 4 pieces of TeleFireEight v1.0 by Bdale on 2017.05.30.
592 Production run of 250 pieces of TeleDongle v3.0 by
593 [Advanced Circuits](http://4pcb.com), received 2018.09.26.
597 Prototype build of 3 pieces of EasyMega v2 proto 1 by Bdale on 2018.10.12.
601 Production run of 250 pieces of EasyMega v2 by
602 [Advanced Circuits](http://4pcb.com), received 2018.12.27.
606 Production run of 50 pieces of TeleFireEight v2 by
607 [Advanced Circuits](http://4pcb.com), received 2019.01.25.
611 Prototype build of 2 pieces of TeleFireOne v2 by Bdale on 2019.02.16
615 Prototype build of 2 pieces of TeleStatic v3 by Bdale on 2019.04.21
619 Production build of 25 pieces of TeleLCO v2.1 by
620 [Advanced Circuits](http://4pcb.com)
624 Production build of 252 pieces of TeleMetrum v3.0 by
625 [Advanced Circuits](http://4pcb.com)
629 Production build of 500 pieces of EasyMini v2.0a by
630 [Advanced Circuits](http://4pcb.com)
635 Production build of 100 pieces of TeleMini v3.0a by
636 [Seeed Studios](https://www.seeedstudio.com/), received 2020.01.21.
640 Production build of 250 pieces of TeleMega v4.0 by
641 [Advanced Circuits](http://4pcb.com), received 2020.02.12
645 Prototype build of 3 pieces of EasyTimer v1 by Bdale on 2020.04.06
649 Production build of 250 pieces of EasyTimer v1 by
650 [Advanced Circuits](http://4pcb.com), received 2020.05.28
654 Prototype build of 6 pieces of EasyMotor v2 by Bdale on 2020.07.25
658 Production build of 250 pieces of TeleBT v4.0b by
659 [Advanced Circuits](http://4pcb.com), received 2020.08.17
663 Prototype build of 3 pieces of TeleGPS v2.0b by Bdale on 2020.08.17