[[!meta title="TeleDongle"]]
# TeleDongle
This is an RF interface designed primarily for use as a ground station
interacting with Altus Metrum flight computers and trackers on board high
power model rockets. The computer interface is USB. RF filter components are
by default set for use in the vicinity of 435 Mhz, but can be altered to
support other frequency ranges.
TeleDongle is now at version v3.0, with 5+ dB better receiver sensitivity
than our previous models!
For the latest TeleDongle firmware and related software, please
visit the [AltOS](../AltOS) page on this site.
## Features ##
### User View ###
* primary ground station for use with other Altus Metrum products
* 70cm ham-band transceiver
* receives data using 38k4 GFSK with forward error correction
* USB interface for power, configuration, and data interface
* 4 pin MicroMaTch connector for initial programming and debug
* application code upgradeable over USB
* 1.1 x 1.1 inch 2-layer board, fits inexpensive Hammond 1551 plastic enclosure
### Developer View ###
* Hardware Features
* [NXP LPC11U14](http://www.nxp.com/products/microcontrollers/cortex_m0_m0/LPC11U14FHI33.html) System-on-Chip
* ARM Cortex-M0 MCU
* 32k Flash
* 6k RAM
* USB 2.0
* 8 12-bit analog inputs
* I2C, SPI, async serial
* digital I/O
* TI [CC1200](http://www.ti.com/product/cc1200) Low Power, High Performance RF Transceiver
* Software Features
* Written mostly in C with some ARM assembler
* Runs from on-chip flash, uses on-chip RAM
* USB serial emulation for data interface
* Tools Used
* [gEDA](http://www.gpleda.org/) for schematic capture and PCB layout
* [GCC](http://gcc.gnu.org/) compiler and source debugger
* Licenses
* The hardware is licensed under the [TAPR](http://www.tapr.org) [Open Hardware License](http://www.tapr.org/ohl.html)
* The software is licensed [GPL version 2](http://www.gnu.org/licenses/old-licenses/gpl-2.0.html)
## Artifacts ##
There is a single manual for most Altus Metrum products,
which is available in [html](../AltOS/doc/altusmetrum.html) and
[pdf](../AltOS/doc/altusmetrum.pdf) formats.
The hardware design current gEDA files are available from
[git.gag.com](http://git.gag.com) in the project
[hw/teledongle](http://git.gag.com/?p=hw/teledongle;a=summary).
For those who don't have ready access to the gEDA suite, here are pdf snapshots
of files in more easily readable form.
* [schematic](v3.0/teledongle-sch.pdf)
* [pcb artwork](v3.0/teledongle-pcb.pdf)
* [bill of materials](v3.0/partslist.csv)
## [History of TeleDongle](history) ##
## Future Plans ##
None! We're very happy with the TeleDongle v3.0 design.
## Features ##
### User View ###
* primary ground station for use with other Altus Metrum products
* 70cm ham-band transceiver
* receives data using 38k4 GFSK with forward error correction
* USB interface for power, configuration, and data interface
* 4 pin MicroMaTch connector for initial programming and debug
* application code upgradeable over USB
* 1.1 x 1.1 inch 2-layer board, fits inexpensive Hammond 1551 plastic enclosure
### Developer View ###
* Hardware Features
* [NXP LPC11U14](http://www.nxp.com/products/microcontrollers/cortex_m0_m0/LPC11U14FHI33.html) System-on-Chip
* ARM Cortex-M0 MCU
* 32k Flash
* 6k RAM
* USB 2.0
* 8 12-bit analog inputs
* I2C, SPI, async serial
* digital I/O
* TI [CC1200](http://www.ti.com/product/cc1200) Low Power, High Performance RF Transceiver
* Software Features
* Written mostly in C with some ARM assembler
* Runs from on-chip flash, uses on-chip RAM
* USB serial emulation for data interface
* Tools Used
* [gEDA](http://www.gpleda.org/) for schematic capture and PCB layout
* [GCC](http://gcc.gnu.org/) compiler and source debugger
* Licenses
* The hardware is licensed under the [TAPR](http://www.tapr.org) [Open Hardware License](http://www.tapr.org/ohl.html)
* The software is licensed [GPL version 2](http://www.gnu.org/licenses/old-licenses/gpl-2.0.html)
## Artifacts ##
There is a single manual for most Altus Metrum products,
which is available in [html](../AltOS/doc/altusmetrum.html) and
[pdf](../AltOS/doc/altusmetrum.pdf) formats.
The hardware design current gEDA files are available from
[git.gag.com](http://git.gag.com) in the project
[hw/teledongle](http://git.gag.com/?p=hw/teledongle;a=summary).
For those who don't have ready access to the gEDA suite, here are pdf snapshots
of files in more easily readable form.
* [schematic](v3.0/teledongle-sch.pdf)
* [pcb artwork](v3.0/teledongle-pcb.pdf)
* [bill of materials](v3.0/partslist.csv)
## [History of TeleDongle](history) ##
## Future Plans ##
None! We're very happy with the TeleDongle v3.0 design.