| 2019-03-23 |
Bdale Garbee | shuffle screw terminal order to ease wiring of arm...
|
commit | commitdiff | tree |
| 2019-03-18 |
Bdale Garbee | update offboard schematic to show safe/arm and fire...
|
commit | commitdiff | tree |
| 2019-03-18 |
Bdale Garbee | added series resistors for switch gpios to layout
|
commit | commitdiff | tree |
| 2019-03-18 |
Bdale Garbee | add series R on switch to gpio nets
|
commit | commitdiff | tree |
| 2019-03-06 |
Bdale Garbee | update copyright assertions to 2019
|
commit | commitdiff | tree |
| 2018-09-09 |
Bdale Garbee | add a companion connector for possible use with matrix...
|
commit | commitdiff | tree |
| 2018-09-09 |
Bdale Garbee | move to lepton-eda and pcb-rnd
|
commit | commitdiff | tree |
| 2018-07-01 |
Bdale Garbee | route complete and drc clean with updated RF section
|
commit | commitdiff | tree |
| 2018-06-29 |
Bdale Garbee | change cap values to 10nF for compatibility with preferred...
|
commit | commitdiff | tree |
| 2018-06-29 |
Bdale Garbee | copy in the TeleMega RF section
|
commit | commitdiff | tree |
| 2018-06-29 |
Bdale Garbee | clip out existing RF section entirely
|
commit | commitdiff | tree |
| 2018-06-29 |
Bdale Garbee | working on radio section layout
|
commit | commitdiff | tree |
| 2018-06-22 |
Bdale Garbee | move RF section south for improved panel cabling, relocate...
|
commit | commitdiff | tree |
| 2018-05-30 |
Bdale Garbee | document what's required to make the 12V switcher on...
|
commit | commitdiff | tree |
| 2018-05-29 |
Bdale Garbee | capture schematic changes as-built for sn 5138
|
commit | commitdiff | tree |
| 2018-05-28 |
Bdale Garbee | make net names easier for keithp to decode
|
commit | commitdiff | tree |
| 2018-05-26 |
Bdale Garbee | change CC1200 pads to have square corners for better...
|
commit | commitdiff | tree |
| 2018-05-26 |
Bdale Garbee | updated attributes for off-board telelco parts
|
commit | commitdiff | tree |
| 2018-05-16 |
Bdale Garbee | update information on required off-board parts
|
commit | commitdiff | tree |
| 2018-05-15 |
Bdale Garbee | correct knob for encoder shaft
|
commit | commitdiff | tree |
| 2018-05-08 |
Bdale Garbee | more silk, more copper shoving
|
commit | commitdiff | tree |
| 2018-05-08 |
Bdale Garbee | lose vestiges of pre-pref-parts era
|
commit | commitdiff | tree |
| 2018-05-08 |
Bdale Garbee | propagate LED and resistor attributes to pcb file
|
commit | commitdiff | tree |
| 2018-05-08 |
Bdale Garbee | shove copper around to avoid departing qfp corner pins...
|
commit | commitdiff | tree |
| 2018-05-08 |
Bdale Garbee | clean up schematic to avoid overlap with longer LED...
|
commit | commitdiff | tree |
| 2018-05-08 |
Bdale Garbee | use 3mm diameter LEDs for battery charger red+green
|
commit | commitdiff | tree |
| 2018-05-07 |
Bdale Garbee | to meet SOC current limits, set limiting resistors...
|
commit | commitdiff | tree |
| 2018-05-05 |
Bdale Garbee | use micro USB symbol in schematic since that's what...
|
commit | commitdiff | tree |
| 2018-05-05 |
Bdale Garbee | rename +12V net to fire12V
|
commit | commitdiff | tree |
| 2018-05-05 |
Bdale Garbee | swap arm and armed at SOC to eliminate interrupt conflict...
|
commit | commitdiff | tree |
| 2018-05-05 |
Bdale Garbee | eliminate radio_marc_int net per keithp
|
commit | commitdiff | tree |
| 2018-05-04 |
Bdale Garbee | label mode and select switch screws
|
commit | commitdiff | tree |
| 2018-05-04 |
Bdale Garbee | route complete, drc clean
|
commit | commitdiff | tree |
| 2018-04-10 |
Bdale Garbee | add explicit mode switch, LED, and push button for...
|
commit | commitdiff | tree |
| 2018-04-05 |
Bdale Garbee | add boost converter to power 12V LED integral to Fire...
|
commit | commitdiff | tree |
| 2018-04-05 |
Bdale Garbee | update part number for encoder
|
commit | commitdiff | tree |
| 2018-04-04 |
Bdale Garbee | move to micromatch version with locking ears for encoder...
|
commit | commitdiff | tree |
| 2018-04-01 |
Bdale Garbee | drop lipo charge current to 400mA
|
commit | commitdiff | tree |
| 2018-03-30 |
Bdale Garbee | clean up offboard parts schematic a bit
|
commit | commitdiff | tree |
| 2018-03-30 |
Bdale Garbee | push RF link quality LEDs closer together
|
commit | commitdiff | tree |
| 2018-03-30 |
Bdale Garbee | added more continuity LEDs, reworked placement, much...
|
commit | commitdiff | tree |
| 2018-03-30 |
Bdale Garbee | add 4 more continuity LEDs, move from spades to screws...
|
commit | commitdiff | tree |
| 2018-03-30 |
Bdale Garbee | move to STM32L152VCT6 for more memory
|
commit | commitdiff | tree |
| 2018-03-30 |
Bdale Garbee | route complete, drc clean, needs work on silk and mech...
|
commit | commitdiff | tree |
| 2018-03-29 |
Bdale Garbee | more work on placement, a few traces added
|
commit | commitdiff | tree |
| 2018-03-21 |
Bdale Garbee | working on revised pcb layout
|
commit | commitdiff | tree |
| 2018-03-20 |
Bdale Garbee | move off-board parts to a separate schematic sheet...
|
commit | commitdiff | tree |
|
projects / hw / telelco / search