Bdale Garbee [Fri, 29 Jun 2018 19:00:46 +0000 (13:00 -0600)]
clip out existing RF section entirely
Bdale Garbee [Fri, 29 Jun 2018 18:38:09 +0000 (12:38 -0600)]
working on radio section layout
Bdale Garbee [Fri, 22 Jun 2018 18:44:32 +0000 (14:44 -0400)]
move RF section south for improved panel cabling, relocate drag race LED
Bdale Garbee [Wed, 30 May 2018 14:23:54 +0000 (08:23 -0600)]
document what's required to make the 12V switcher on v2.0 work
Bdale Garbee [Tue, 29 May 2018 19:32:30 +0000 (13:32 -0600)]
capture schematic changes as-built for sn 5138
Bdale Garbee [Mon, 28 May 2018 21:44:13 +0000 (15:44 -0600)]
make net names easier for keithp to decode
Bdale Garbee [Sat, 26 May 2018 21:38:35 +0000 (15:38 -0600)]
change CC1200 pads to have square corners for better stencil cutting
Bdale Garbee [Sat, 26 May 2018 17:43:34 +0000 (11:43 -0600)]
updated attributes for off-board telelco parts
Bdale Garbee [Wed, 16 May 2018 07:04:34 +0000 (01:04 -0600)]
update information on required off-board parts
Bdale Garbee [Tue, 15 May 2018 22:51:51 +0000 (16:51 -0600)]
correct knob for encoder shaft
Bdale Garbee [Tue, 8 May 2018 20:33:53 +0000 (13:33 -0700)]
more silk, more copper shoving
Bdale Garbee [Tue, 8 May 2018 20:10:24 +0000 (13:10 -0700)]
lose vestiges of pre-pref-parts era
Bdale Garbee [Tue, 8 May 2018 20:00:32 +0000 (13:00 -0700)]
propagate LED and resistor attributes to pcb file
Bdale Garbee [Tue, 8 May 2018 19:59:25 +0000 (12:59 -0700)]
shove copper around to avoid departing qfp corner pins off their sides
Bdale Garbee [Tue, 8 May 2018 19:55:34 +0000 (12:55 -0700)]
clean up schematic to avoid overlap with longer LED value texts
Bdale Garbee [Tue, 8 May 2018 19:54:28 +0000 (12:54 -0700)]
use 3mm diameter LEDs for battery charger red+green
Bdale Garbee [Mon, 7 May 2018 05:49:35 +0000 (22:49 -0700)]
to meet SOC current limits, set limiting resistors for 4mA per LED
Bdale Garbee [Sat, 5 May 2018 05:13:09 +0000 (22:13 -0700)]
use micro USB symbol in schematic since that's what we're really using
Bdale Garbee [Sat, 5 May 2018 05:07:46 +0000 (22:07 -0700)]
rename +12V net to fire12V
Bdale Garbee [Sat, 5 May 2018 05:04:47 +0000 (22:04 -0700)]
swap arm and armed at SOC to eliminate interrupt conflict with spare4
Bdale Garbee [Sat, 5 May 2018 04:55:29 +0000 (21:55 -0700)]
eliminate radio_marc_int net per keithp
Bdale Garbee [Fri, 4 May 2018 20:38:49 +0000 (13:38 -0700)]
label mode and select switch screws
Bdale Garbee [Fri, 4 May 2018 20:30:50 +0000 (13:30 -0700)]
route complete, drc clean
Bdale Garbee [Tue, 10 Apr 2018 23:13:19 +0000 (17:13 -0600)]
add explicit mode switch, LED, and push button for drag race mode
Bdale Garbee [Thu, 5 Apr 2018 03:48:45 +0000 (21:48 -0600)]
add boost converter to power 12V LED integral to Fire button
Bdale Garbee [Thu, 5 Apr 2018 03:48:28 +0000 (21:48 -0600)]
update part number for encoder
Bdale Garbee [Wed, 4 Apr 2018 20:55:12 +0000 (14:55 -0600)]
move to micromatch version with locking ears for encoder cable
Bdale Garbee [Sun, 1 Apr 2018 04:07:01 +0000 (22:07 -0600)]
drop lipo charge current to 400mA
Bdale Garbee [Fri, 30 Mar 2018 17:09:13 +0000 (11:09 -0600)]
clean up offboard parts schematic a bit
Bdale Garbee [Fri, 30 Mar 2018 17:05:15 +0000 (11:05 -0600)]
push RF link quality LEDs closer together
Bdale Garbee [Fri, 30 Mar 2018 17:01:07 +0000 (11:01 -0600)]
added more continuity LEDs, reworked placement, much more silk
Bdale Garbee [Fri, 30 Mar 2018 04:23:22 +0000 (22:23 -0600)]
add 4 more continuity LEDs, move from spades to screws for off-board switches
Bdale Garbee [Fri, 30 Mar 2018 04:00:03 +0000 (22:00 -0600)]
move to STM32L152VCT6 for more memory
Bdale Garbee [Fri, 30 Mar 2018 03:52:59 +0000 (21:52 -0600)]
route complete, drc clean, needs work on silk and mech check
Bdale Garbee [Thu, 29 Mar 2018 20:36:47 +0000 (14:36 -0600)]
more work on placement, a few traces added
Bdale Garbee [Wed, 21 Mar 2018 06:21:58 +0000 (00:21 -0600)]
working on revised pcb layout
Bdale Garbee [Tue, 20 Mar 2018 22:58:45 +0000 (16:58 -0600)]
move off-board parts to a separate schematic sheet, various changes
Keith Packard [Thu, 2 Nov 2017 16:30:09 +0000 (09:30 -0700)]
Remove SPI filters. Remove part attributes
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 2 Nov 2017 16:27:15 +0000 (09:27 -0700)]
Update attribs to our usual set
Keith Packard [Tue, 19 Apr 2016 18:08:19 +0000 (14:08 -0400)]
Replace connectors. Add middle layers
Switch connectors are now 1/4" quick connect
USB has both vertical micro and 5-pin plug
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 2 Nov 2017 16:16:59 +0000 (09:16 -0700)]
Switch to shared build infra
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Oct 2014 02:34:51 +0000 (19:34 -0700)]
Update passive parts to current DK stock
Also changed 10nF value to 0.01uF
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Oct 2014 02:25:08 +0000 (19:25 -0700)]
Update version in pcb and sch to 1.0
Prepare for release with this version
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Oct 2014 02:13:00 +0000 (19:13 -0700)]
Use altusmetrum packages/symbols. Fix vendor parts. Switch to CC1200
Remove all of the local packages and symbol files. Change references
to ../altusmetrum.
Swap CC1120 for CC1200, switch xtal to 40MHz to match.
Fix some passives to our usual parts.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 27 Oct 2014 02:01:13 +0000 (19:01 -0700)]
Switch to shared altusmetrum symbols
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 6 Mar 2013 04:02:54 +0000 (20:02 -0800)]
Steal partslist makefile fragments from micropeak
Someday, maybe a bunch of Makefile fragments should get moved to the
altusmetrum repo so they can be shared more easily. For now,
cult-n-paste them here.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 6 Mar 2013 03:45:21 +0000 (19:45 -0800)]
Switch power trace around S side of 1125 to fat
Makes sure all of the 1125 power inputs are hooked to fat traces
Required rerouting the E side of the 1125
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 6 Mar 2013 03:19:53 +0000 (19:19 -0800)]
Build PDF versions of schematics and board layouts
Makes showing other people a lot easier
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 17 Dec 2012 06:58:02 +0000 (22:58 -0800)]
Add connection from GPIO3 to PD2 for radio_marc_int
We use this to tell when the radio chip has errored out to keep from
wedging stuff.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 1 Dec 2012 22:41:29 +0000 (14:41 -0800)]
Improve silk text positioning
Shrink labels around the CC1125 so that there is enough room for all
of them, then shuffle around to suit
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 1 Dec 2012 21:31:03 +0000 (13:31 -0800)]
Switch to CC1125
Replace the CC1111 with a CC1125; simplifying the production process
and increasing the radio range.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 6 Oct 2012 05:00:46 +0000 (22:00 -0700)]
Replace two-color LED with three separate LEDs
Color-blind users cannot distinguish between red/yellow/green in a
single LED, so use three separate LEDs to allow them to distinguish by
position instead.
This also changes the color for some LEDs: continuity are green,
remote safety off is red.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 2 Oct 2012 23:12:35 +0000 (16:12 -0700)]
Add vendor part number for STM32L152VBT6
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 2 Oct 2012 22:56:45 +0000 (15:56 -0700)]
Switch to LEDs without standoffs
This makes the LEDs rise no higher than the rotary switches, making it
unnecessary to cut holes for them.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 23 Sep 2012 15:17:52 +0000 (08:17 -0700)]
Shove schematic bits around to make it easier to read
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 23 Sep 2012 15:15:40 +0000 (08:15 -0700)]
Shuffle battery and switch connectors around
Make sure the battery connector isn't covered by the switch cable by
moving it E of the switch connector, move the switch connector a bit
NW to make room.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 11 Sep 2012 21:04:07 +0000 (14:04 -0700)]
Update to new PCB version. Fix DRC error
New PCB version rewrites all dimensions to include units.
Also fixed a minor DRC issue.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 11 Sep 2012 05:49:43 +0000 (22:49 -0700)]
Generate .zip file more cleanly
Correct the dependencies so that the contents of the zip file get
generated when the .pcb file changes.
Don't require an explicit list of the zip file contents in the Makefile.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 11 Sep 2012 05:48:37 +0000 (22:48 -0700)]
Fix DRC errors found by freedfm
A couple of vias were mis-placed by 1mil, making traces too close
together. The internal DRC rules checking code didn't find them.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 6 Sep 2012 23:43:44 +0000 (16:43 -0700)]
Move current limit resistors closer to CPUs. Add text to connectors.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 6 Sep 2012 23:05:35 +0000 (16:05 -0700)]
Route complete on v0.2 telelco
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 6 Sep 2012 07:29:45 +0000 (00:29 -0700)]
Bump to version 0.2
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 6 Sep 2012 07:26:52 +0000 (00:26 -0700)]
Get started switching to the STM32L152VBT6
The LCD digits need more wires than the 64-bit version provides, so
switch to the 100pin package. Lots of rats left, but it's a start at least.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 6 Aug 2012 00:35:07 +0000 (17:35 -0700)]
Build DK parts list
Keith Packard [Sun, 5 Aug 2012 23:48:41 +0000 (16:48 -0700)]
Move text around
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 5 Aug 2012 08:36:08 +0000 (01:36 -0700)]
Use DK number instead of mf number for 220pF caps
Keith Packard [Sun, 5 Aug 2012 08:30:56 +0000 (01:30 -0700)]
Replace out-of-stock components
Keith Packard [Sat, 4 Aug 2012 20:46:07 +0000 (13:46 -0700)]
ignore backup files
Keith Packard [Sat, 4 Aug 2012 20:45:08 +0000 (13:45 -0700)]
Make NC pins explicit
Cleans up the DRC file
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 4 Aug 2012 20:41:21 +0000 (13:41 -0700)]
Fix pintypes
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 4 Aug 2012 20:30:26 +0000 (13:30 -0700)]
Hide LCD digit attributes
Keith Packard [Sat, 4 Aug 2012 20:23:58 +0000 (13:23 -0700)]
Clean up packages and symbols
Remove backup files. Add conn-6
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 4 Aug 2012 20:22:09 +0000 (13:22 -0700)]
Add footprints for STM32 and tyco header
Keith Packard [Sat, 4 Aug 2012 20:20:46 +0000 (13:20 -0700)]
Add data sheets for power switch and RSSI led
Keith Packard [Sat, 4 Aug 2012 20:03:49 +0000 (13:03 -0700)]
Hide LED values
Keith Packard [Sat, 4 Aug 2012 19:56:29 +0000 (12:56 -0700)]
Use tyco 6-pin header for all switches
Should make connecting the switches a lot easier
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 4 Aug 2012 05:16:11 +0000 (22:16 -0700)]
gerber files dependency was incorrect
leading to the file never getting rebuilt
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 4 Aug 2012 05:08:30 +0000 (22:08 -0700)]
Flush out partslist.
Add vendor, part-number and other information as needed
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 4 Aug 2012 04:01:15 +0000 (21:01 -0700)]
Fix makefile to build partslist with -j flag
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 3 Aug 2012 08:55:31 +0000 (01:55 -0700)]
PEC11 footprint was accidentally a clone of PEC11L
These aren't quite the same...
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 3 Aug 2012 08:36:49 +0000 (01:36 -0700)]
Re-route rotary switch connections
Shorten them considerably to reduce potential interference issues.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 3 Aug 2012 08:01:27 +0000 (01:01 -0700)]
Move some silk around
The SPI snubber labels were all scrambled.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 3 Aug 2012 07:32:00 +0000 (00:32 -0700)]
Add bypass caps to all STM32L power leads
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 3 Aug 2012 07:07:25 +0000 (00:07 -0700)]
Add SPI snubbers.
Just in case
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 30 Jul 2012 04:09:29 +0000 (21:09 -0700)]
switch to STM152LRBT6
Need the LCD controller in the 152 version
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 24 Jul 2012 06:05:08 +0000 (23:05 -0700)]
Add serial debug connector for cc1111
Useful to separately debug the cc1111
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 24 Jul 2012 00:34:12 +0000 (17:34 -0700)]
Clean up pcb -- unthermal a couple vias, erase dirt
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 24 Jul 2012 00:28:20 +0000 (17:28 -0700)]
Route complete with cc1111 radio again
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 23 Jul 2012 16:43:26 +0000 (09:43 -0700)]
Switch back to the cc1111 for a radio
The cc1120 is missing both FEC and AES; gonna be way easier (and
cheaper) to just use the cc1111 for this thing.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 22 Jul 2012 07:23:37 +0000 (00:23 -0700)]
Move LEDs to back of board. Unthermal vias
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 16 Jul 2012 20:23:08 +0000 (13:23 -0700)]
Add π filters on all links between CPU and CC1120
Attempt to keep RFI out of the CPU
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 10 Jul 2012 05:42:02 +0000 (22:42 -0700)]
Move ink around
Keep text from sitting on top of pads or underneath components
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 10 Jul 2012 05:25:07 +0000 (22:25 -0700)]
Switch to CC1120 radio. Add reset controller
Probably need some RFI mitigation on the SPI leads between the CC1120
and the CPU.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 22 Jun 2012 23:31:17 +0000 (16:31 -0700)]
Use 64-pin STM32L processor. Shrink board to 4.5 x 3.75
Looks like we'll be able to use 64-bit processors almost everywhere,
so switch to that pinout for this product as well.
One proposed case, the Pelican 1120 has only about 3.875" clearance
between the two edges of the panel frame. Shrink the board to make
it fit.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 13 Jun 2012 19:33:58 +0000 (12:33 -0700)]
Add cap on vlcd line, disconnect vlcd from +3.3V
This lets us use the internal lcd voltage generator.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 13 Jun 2012 15:44:45 +0000 (08:44 -0700)]
Ignore DRC on outline. Shift USB cutout to center on connector.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 13 Jun 2012 15:24:26 +0000 (08:24 -0700)]
Add 22-ohm resistors to USB data lines
Probably a good idea.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 9 Jun 2012 10:38:14 +0000 (03:38 -0700)]
Move ink for serial number down under the license.
Seems like a more reasonable spot.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 9 Jun 2012 10:35:04 +0000 (03:35 -0700)]
Use all through-hole LEDs. Add mounting holes.
Replace SMT LEDs with larger through-hole versions so they will be
visible through the panel.
Add 8 mounting holes.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 9 Jun 2012 08:35:56 +0000 (01:35 -0700)]
Nearly route complete with LCD and knobs on backside of board.
Just need to mess with LEDs now
projects / hw / telelco / log