projects / hw / telegps / search
| 2012-12-21 | Keith Packard | Find DK number for 10 ohm resistor Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-21 | Keith Packard | Add more part values Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-21 | Keith Packard | Correct STM32L part number Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-21 | Keith Packard | Update DK part numbers Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-21 | Keith Packard | Add a handful of bypass caps Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-21 | Keith Packard | Fix board size to 1 inch high Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-21 | Keith Packard | Shuffle ink around Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-21 | Keith Packard | Route the battery charger. Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-21 | Keith Packard | Finish routing RF section Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-21 | Keith Packard | Add a power switch connector (two pin holes). Route... Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-20 | Keith Packard | Move vias and traces from underneath GPS Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-20 | Keith Packard | Route most of the CPU Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-20 | Keith Packard | Switch GPS to usart2 on pins 11 and 12 Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-20 | Keith Packard | Route PA controls towards PA Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-20 | Keith Packard | Route cc115L Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-20 | Keith Packard | Stitch GPS ground plane. Rotate microSD. Start PA route. Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-20 | Keith Packard | Update ground plane and VCC. Place microUSB Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-20 | Keith Packard | Update CC115L component values Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-20 | Keith Packard | Add value and footprints for PA section Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-20 | Keith Packard | Add RF components. Hook up microSD card. Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-19 | Keith Packard | geda doesn't like 'passive' pins. Use 'pas' instead Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-19 | Keith Packard | Add two more signal layers and planned outline Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-19 | Keith Packard | Initial schematic and pcb floor planning Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |
| 2012-12-19 | Keith Packard | Import packages and symbols to be used for TeleGPS Signed-off-by: Keith Packard <keithp@keithp.com> |
commit | commitdiff | tree |