hw/telefireone
2020-09-18 Bdale GarbeeMerge branch 'master' of ssh://git.gag.com/scm/git...
2019-07-27 Keith PackardSwitch pyro series resistors to 1k
2018-12-10 Bdale Garbeemove to pcb-rnd, fix 0.25" spade that's on the wrong...
2018-05-21 Bdale Garbeelose paste on tab pads
2018-03-27 Bdale Garbeeadd missing component type attribute
2017-09-16 Bdale Garbeeadd cap to adc refout just in case, connect final two... fab-v2.0
2017-09-12 Bdale Garbeeremove errant bit of botton layer copper
2017-09-11 Bdale Garbeeroute complete, drc clean, with better ADC chip
2017-09-11 Bdale Garbeemove to assertionless title block, prepare for larger...
2017-09-10 Bdale Garbeeshove some copper around
2017-09-10 Bdale Garbeeroute conplete, DRC clean
2017-09-10 Bdale Garbeeadded external 24-bit SPI-attached ADC
2017-05-19 Bdale Garbeesilk grooming
2017-05-19 Bdale Garbeemove RF link quality LEDs so they aren't crowding the...
2017-05-19 Bdale Garbeeadd pass transistor to stiffen load cell reference...
2017-05-15 Bdale Garbeeswap position of pressure sensor and alarm output screw...
2017-05-15 Bdale Garbeere-branding as "TeleFireOne"
2017-05-15 Bdale Garbeeeliminate 10k pull-down on BOOT1 origin/HEAD origin/master
2017-05-14 Bdale Garbeepcb layout complete and drc clean again
2017-05-13 Bdale Garbeeadjust pin assignments to ease pcb routing
2017-05-13 Bdale Garbeedefault gain resistor value, eliminate amp output divid...
2017-05-13 Bdale Garbeedocument example load cell amplifier gain resistor...
2017-05-12 Bdale Garbeework in progress on layout
2017-05-08 Bdale Garbeev1.2 layout work in progress
2017-05-08 Bdale Garbeeelide USB power connector (aka, the laptop killer)
2017-05-08 Bdale Garbeemove from v-bite to AMP footprint for BNC connector
2017-05-08 Bdale Garbeeelide beeper from schematic, not loud enough for intend...
2017-05-07 Bdale Garbeemove therm_io to a timer input pin
2017-04-14 Bdale Garbeeforward annotate attribute changes from schematic to pcb
2017-04-14 Bdale Garbeeclean up attribute noise
2017-03-03 Bdale Garbeeswitch to 10V default for load cell excitation
2016-04-11 Keith PackardMove components away from edge of board where wires... fab-v1.1
2016-04-08 Keith PackardMove refdes around on silk a bit more
2016-04-08 Keith PackardMark off test-stand specific components in schematic
2016-04-07 Keith Packardmove refdes around to make loading parts possible
2016-02-10 Bdale GarbeeMerge branch 'master' of ssh://gag.com/~keithp/telefiretwo fab-v1.0
2016-02-10 Bdale Garbeeprepare to send to seeed
2016-02-06 Bdale Garbeeclean up schematic whitespace
2016-02-06 Bdale Garbeevoltage divider on pressure sensor output, ore bypass...
2016-02-05 Bdale Garbeeeliminate refdes from silk
2016-02-02 Keith PackardAdjust size back. Add outline bits to slots
2016-02-02 Bdale Garbeeall silked up...
2016-01-30 Bdale Garbeeroute complete, silk still needs connector labels
2016-01-21 Bdale Garbeeadded USB pin header, removed most of the copper, worki...
2016-01-18 Bdale Garbeemore part shoving
2016-01-18 Keith PackardSuggest different connector layout
2016-01-18 Bdale Garbeeall parts placed
2016-01-17 Bdale Garbeeadd 5V regulator to schematic, needed for pressure...
2016-01-17 Bdale Garbeeadd load cell and thermistor sensor circuits
2016-01-17 Bdale Garbeemove LDO input cap to a 220uF through-hole part
2016-01-17 Keith PackardSwitch to full-size LEDs
2015-12-24 Keith PackardSwitch to TO252FET footprint
2015-12-23 Keith PackardSwitch FET footprints to TO252
2015-12-21 Keith PackardAdd beeper
2015-12-18 Keith PackardHook up PB6 to force boot loader entry.
2015-12-17 Keith PackardAdd pyro voltage sense, as in TeleFire
2015-12-16 Keith PackardSwitch to 22uF cap. Rewire SPI.
2015-12-16 Keith PackardMake refdes useful for loading boards.
2015-11-21 Keith PackardRoute complete and off to seeed v0.1
2015-11-21 Keith PackardRename nets to match pad numbers
2015-11-16 Keith PackardSwitch to CC1200 radio part
2015-10-29 Keith PackardAdd .gitignore
2015-10-29 Keith PackardDisable visibility of device and footprint attributes
2015-10-28 Keith PackardForward annotate a few part attribute changes from...
2015-10-28 Keith PackardSet 'value' for our huge screw terminal device
2015-10-28 Keith PackardMove refdes around on the pcb
2015-10-28 Keith PackardRemove unneeded part attributes
2015-10-28 Keith PackardClean up traces a bit
2015-10-27 Keith PackardRoute on two layers
2015-10-27 Keith PackardCut rectangles for USB connector slots
2015-10-27 Keith PackardAdd USB power jumper for bringup. Fix floods.
2015-10-27 Keith PackardSwitch to shared build process
2015-10-25 Keith PackardInitial import