#include "config.h"
#endif
+#include <jtag/adapter.h>
#include <jtag/interface.h>
#include <transport/transport.h>
#include "bitbang.h"
#define BCM2835_PADS_GPIO_0_27 (bcm2835_peri_base + 0x100000)
#define BCM2835_PADS_GPIO_0_27_OFFSET (0x2c / 4)
+/* See "GPIO Function Select Registers (GPFSELn)" in "Broadcom BCM2835 ARM Peripherals" datasheet. */
+#define BCM2835_GPIO_MODE_INPUT 0
+#define BCM2835_GPIO_MODE_OUTPUT 1
+
/* GPIO setup macros */
#define MODE_GPIO(g) (*(pio_base+((g)/10))>>(((g)%10)*3) & 7)
#define INP_GPIO(g) do { *(pio_base+((g)/10)) &= ~(7<<(((g)%10)*3)); } while (0)
#define SET_MODE_GPIO(g, m) do { /* clear the mode bits first, then set as necessary */ \
INP_GPIO(g); \
*(pio_base+((g)/10)) |= ((m)<<(((g)%10)*3)); } while (0)
-#define OUT_GPIO(g) SET_MODE_GPIO(g, 1)
+#define OUT_GPIO(g) SET_MODE_GPIO(g, BCM2835_GPIO_MODE_OUTPUT)
#define GPIO_SET (*(pio_base+7)) /* sets bits which are 1, ignores bits which are 0 */
#define GPIO_CLR (*(pio_base+10)) /* clears bits which are 1, ignores bits which are 0 */
static volatile uint32_t *pio_base = MAP_FAILED;
static volatile uint32_t *pads_base = MAP_FAILED;
-static bb_value_t bcm2835gpio_read(void);
-static int bcm2835gpio_write(int tck, int tms, int tdi);
-
-static int bcm2835_swdio_read(void);
-static void bcm2835_swdio_drive(bool is_output);
-static int bcm2835gpio_swd_write(int swclk, int swdio);
-
-static int bcm2835gpio_init(void);
-static int bcm2835gpio_quit(void);
-
-static struct bitbang_interface bcm2835gpio_bitbang = {
- .read = bcm2835gpio_read,
- .write = bcm2835gpio_write,
- .swdio_read = bcm2835_swdio_read,
- .swdio_drive = bcm2835_swdio_drive,
- .swd_write = bcm2835gpio_swd_write,
- .blink = NULL
-};
-
-/* GPIO numbers for each signal. Negative values are invalid */
-static int tck_gpio = -1;
-static int tck_gpio_mode;
-static int tms_gpio = -1;
-static int tms_gpio_mode;
-static int tdi_gpio = -1;
-static int tdi_gpio_mode;
-static int tdo_gpio = -1;
-static int tdo_gpio_mode;
-static int trst_gpio = -1;
-static int trst_gpio_mode;
-static int srst_gpio = -1;
-static int srst_gpio_mode;
-static int swclk_gpio = -1;
-static int swclk_gpio_mode;
-static int swdio_gpio = -1;
-static int swdio_gpio_mode;
-static int swdio_dir_gpio = -1;
-static int swdio_dir_gpio_mode;
-
/* Transition delay coefficients */
static int speed_coeff = 113714;
static int speed_offset = 28;
static unsigned int jtag_delay;
-static int is_gpio_valid(int gpio)
+static const struct adapter_gpio_config *adapter_gpio_config;
+static int initial_gpio_mode[ADAPTER_GPIO_IDX_NUM];
+
+static bool is_gpio_config_valid(enum adapter_gpio_config_index idx)
{
- return gpio >= 0 && gpio <= 31;
+ /* Only chip 0 is supported, accept unset value (-1) too */
+ return adapter_gpio_config[idx].chip_num >= -1
+ && adapter_gpio_config[idx].chip_num <= 0
+ && adapter_gpio_config[idx].gpio_num >= 0
+ && adapter_gpio_config[idx].gpio_num <= 31;
+}
+
+static void set_gpio_value(const struct adapter_gpio_config *gpio_config, int value)
+{
+ value = value ^ (gpio_config->active_low ? 1 : 0);
+ switch (gpio_config->drive) {
+ case ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL:
+ if (value)
+ GPIO_SET = 1 << gpio_config->gpio_num;
+ else
+ GPIO_CLR = 1 << gpio_config->gpio_num;
+ /* For performance reasons assume the GPIO is already set as an output
+ * and therefore the call can be omitted here.
+ */
+ break;
+ case ADAPTER_GPIO_DRIVE_MODE_OPEN_DRAIN:
+ if (value) {
+ INP_GPIO(gpio_config->gpio_num);
+ } else {
+ GPIO_CLR = 1 << gpio_config->gpio_num;
+ OUT_GPIO(gpio_config->gpio_num);
+ }
+ break;
+ case ADAPTER_GPIO_DRIVE_MODE_OPEN_SOURCE:
+ if (value) {
+ GPIO_SET = 1 << gpio_config->gpio_num;
+ OUT_GPIO(gpio_config->gpio_num);
+ } else {
+ INP_GPIO(gpio_config->gpio_num);
+ }
+ break;
+ }
+}
+
+static void restore_gpio(enum adapter_gpio_config_index idx)
+{
+ if (is_gpio_config_valid(idx))
+ SET_MODE_GPIO(adapter_gpio_config[idx].gpio_num, initial_gpio_mode[idx]);
+}
+
+static void initialize_gpio(enum adapter_gpio_config_index idx)
+{
+ if (!is_gpio_config_valid(idx))
+ return;
+
+ initial_gpio_mode[idx] = MODE_GPIO(adapter_gpio_config[idx].gpio_num);
+ LOG_DEBUG("saved GPIO mode for %s (GPIO %d %d): %d",
+ adapter_gpio_get_name(idx), adapter_gpio_config[idx].chip_num, adapter_gpio_config[idx].gpio_num,
+ initial_gpio_mode[idx]);
+
+ if (adapter_gpio_config[idx].pull != ADAPTER_GPIO_PULL_NONE) {
+ LOG_WARNING("BCM2835 GPIO does not support pull-up or pull-down settings (signal %s)",
+ adapter_gpio_get_name(idx));
+ }
+
+ switch (adapter_gpio_config[idx].init_state) {
+ case ADAPTER_GPIO_INIT_STATE_INACTIVE:
+ set_gpio_value(&adapter_gpio_config[idx], 0);
+ break;
+ case ADAPTER_GPIO_INIT_STATE_ACTIVE:
+ set_gpio_value(&adapter_gpio_config[idx], 1);
+ break;
+ case ADAPTER_GPIO_INIT_STATE_INPUT:
+ INP_GPIO(adapter_gpio_config[idx].gpio_num);
+ break;
+ }
+
+ /* Direction for non push-pull is already set by set_gpio_value() */
+ if (adapter_gpio_config[idx].drive == ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL)
+ OUT_GPIO(adapter_gpio_config[idx].gpio_num);
}
static bb_value_t bcm2835gpio_read(void)
{
- return (GPIO_LEV & 1<<tdo_gpio) ? BB_HIGH : BB_LOW;
+ unsigned int shift = adapter_gpio_config[ADAPTER_GPIO_IDX_TDO].gpio_num;
+ uint32_t value = (GPIO_LEV >> shift) & 1;
+ return value ^ (adapter_gpio_config[ADAPTER_GPIO_IDX_TDO].active_low ? BB_HIGH : BB_LOW);
+
}
static int bcm2835gpio_write(int tck, int tms, int tdi)
{
- uint32_t set = tck<<tck_gpio | tms<<tms_gpio | tdi<<tdi_gpio;
- uint32_t clear = !tck<<tck_gpio | !tms<<tms_gpio | !tdi<<tdi_gpio;
+ uint32_t set = tck << adapter_gpio_config[ADAPTER_GPIO_IDX_TCK].gpio_num |
+ tms << adapter_gpio_config[ADAPTER_GPIO_IDX_TMS].gpio_num |
+ tdi << adapter_gpio_config[ADAPTER_GPIO_IDX_TDI].gpio_num;
+ uint32_t clear = !tck << adapter_gpio_config[ADAPTER_GPIO_IDX_TCK].gpio_num |
+ !tms << adapter_gpio_config[ADAPTER_GPIO_IDX_TMS].gpio_num |
+ !tdi << adapter_gpio_config[ADAPTER_GPIO_IDX_TDI].gpio_num;
GPIO_SET = set;
GPIO_CLR = clear;
return ERROR_OK;
}
-static int bcm2835gpio_swd_write(int swclk, int swdio)
+/* Requires push-pull drive mode for swclk and swdio */
+static int bcm2835gpio_swd_write_fast(int swclk, int swdio)
{
- uint32_t set = swclk << swclk_gpio | swdio << swdio_gpio;
- uint32_t clear = !swclk << swclk_gpio | !swdio << swdio_gpio;
+ swclk = swclk ^ (adapter_gpio_config[ADAPTER_GPIO_IDX_SWCLK].active_low ? 1 : 0);
+ swdio = swdio ^ (adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].active_low ? 1 : 0);
+
+ uint32_t set = swclk << adapter_gpio_config[ADAPTER_GPIO_IDX_SWCLK].gpio_num |
+ swdio << adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].gpio_num;
+ uint32_t clear = !swclk << adapter_gpio_config[ADAPTER_GPIO_IDX_SWCLK].gpio_num |
+ !swdio << adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].gpio_num;
GPIO_SET = set;
GPIO_CLR = clear;
return ERROR_OK;
}
-/* (1) assert or (0) deassert reset lines */
-static int bcm2835gpio_reset(int trst, int srst)
+/* Generic mode that works for open-drain/open-source drive modes, but slower */
+static int bcm2835gpio_swd_write_generic(int swclk, int swdio)
{
- uint32_t set = 0;
- uint32_t clear = 0;
+ set_gpio_value(&adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO], swdio);
+ set_gpio_value(&adapter_gpio_config[ADAPTER_GPIO_IDX_SWCLK], swclk); /* Write clock last */
- if (is_gpio_valid(trst_gpio)) {
- set |= !trst<<trst_gpio;
- clear |= trst<<trst_gpio;
- }
+ for (unsigned int i = 0; i < jtag_delay; ++i)
+ asm volatile ("");
- if (is_gpio_valid(srst_gpio)) {
- set |= !srst<<srst_gpio;
- clear |= srst<<srst_gpio;
- }
+ return ERROR_OK;
+}
- GPIO_SET = set;
- GPIO_CLR = clear;
+/* (1) assert or (0) deassert reset lines */
+static int bcm2835gpio_reset(int trst, int srst)
+{
+ /* As the "adapter reset_config" command keeps the srst and trst gpio drive
+ * mode settings in sync we can use our standard set_gpio_value() function
+ * that honours drive mode and active low.
+ */
+ if (is_gpio_config_valid(ADAPTER_GPIO_IDX_SRST))
+ set_gpio_value(&adapter_gpio_config[ADAPTER_GPIO_IDX_SRST], srst);
+ if (is_gpio_config_valid(ADAPTER_GPIO_IDX_TRST))
+ set_gpio_value(&adapter_gpio_config[ADAPTER_GPIO_IDX_TRST], trst);
+
+ LOG_DEBUG("BCM2835 GPIO: bcm2835gpio_reset(%d, %d), trst_gpio: %d %d, srst_gpio: %d %d",
+ trst, srst,
+ adapter_gpio_config[ADAPTER_GPIO_IDX_TRST].chip_num, adapter_gpio_config[ADAPTER_GPIO_IDX_TRST].gpio_num,
+ adapter_gpio_config[ADAPTER_GPIO_IDX_SRST].chip_num, adapter_gpio_config[ADAPTER_GPIO_IDX_SRST].gpio_num);
return ERROR_OK;
}
static void bcm2835_swdio_drive(bool is_output)
{
- if (is_gpio_valid(swdio_dir_gpio)) {
- if (is_output) {
- GPIO_SET = 1 << swdio_dir_gpio;
- OUT_GPIO(swdio_gpio);
- } else {
- INP_GPIO(swdio_gpio);
- GPIO_CLR = 1 << swdio_dir_gpio;
- }
+ if (is_output) {
+ if (is_gpio_config_valid(ADAPTER_GPIO_IDX_SWDIO_DIR))
+ set_gpio_value(&adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO_DIR], 1);
+ OUT_GPIO(adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].gpio_num);
} else {
- if (is_output)
- OUT_GPIO(swdio_gpio);
- else
- INP_GPIO(swdio_gpio);
+ INP_GPIO(adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].gpio_num);
+ if (is_gpio_config_valid(ADAPTER_GPIO_IDX_SWDIO_DIR))
+ set_gpio_value(&adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO_DIR], 0);
}
}
static int bcm2835_swdio_read(void)
{
- return !!(GPIO_LEV & 1 << swdio_gpio);
+ unsigned int shift = adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].gpio_num;
+ uint32_t value = (GPIO_LEV >> shift) & 1;
+ return value ^ (adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].active_low ? 1 : 0);
}
static int bcm2835gpio_khz(int khz, int *jtag_speed)
{
if (!khz) {
- LOG_DEBUG("RCLK not supported");
+ LOG_DEBUG("BCM2835 GPIO: RCLK not supported");
return ERROR_FAIL;
}
*jtag_speed = speed_coeff/khz - speed_offset;
return ERROR_OK;
}
-COMMAND_HANDLER(bcm2835gpio_handle_jtag_gpionums)
-{
- if (CMD_ARGC == 4) {
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[0], tck_gpio);
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[1], tms_gpio);
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[2], tdi_gpio);
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[3], tdo_gpio);
- } else if (CMD_ARGC != 0) {
- return ERROR_COMMAND_SYNTAX_ERROR;
- }
-
- command_print(CMD,
- "BCM2835 GPIO config: tck = %d, tms = %d, tdi = %d, tdo = %d",
- tck_gpio, tms_gpio, tdi_gpio, tdo_gpio);
-
- return ERROR_OK;
-}
-
-COMMAND_HANDLER(bcm2835gpio_handle_jtag_gpionum_tck)
-{
- if (CMD_ARGC == 1)
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[0], tck_gpio);
-
- command_print(CMD, "BCM2835 GPIO config: tck = %d", tck_gpio);
- return ERROR_OK;
-}
-
-COMMAND_HANDLER(bcm2835gpio_handle_jtag_gpionum_tms)
-{
- if (CMD_ARGC == 1)
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[0], tms_gpio);
-
- command_print(CMD, "BCM2835 GPIO config: tms = %d", tms_gpio);
- return ERROR_OK;
-}
-
-COMMAND_HANDLER(bcm2835gpio_handle_jtag_gpionum_tdo)
-{
- if (CMD_ARGC == 1)
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[0], tdo_gpio);
-
- command_print(CMD, "BCM2835 GPIO config: tdo = %d", tdo_gpio);
- return ERROR_OK;
-}
-
-COMMAND_HANDLER(bcm2835gpio_handle_jtag_gpionum_tdi)
-{
- if (CMD_ARGC == 1)
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[0], tdi_gpio);
-
- command_print(CMD, "BCM2835 GPIO config: tdi = %d", tdi_gpio);
- return ERROR_OK;
-}
-
-COMMAND_HANDLER(bcm2835gpio_handle_jtag_gpionum_srst)
-{
- if (CMD_ARGC == 1)
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[0], srst_gpio);
-
- command_print(CMD, "BCM2835 GPIO config: srst = %d", srst_gpio);
- return ERROR_OK;
-}
-
-COMMAND_HANDLER(bcm2835gpio_handle_jtag_gpionum_trst)
-{
- if (CMD_ARGC == 1)
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[0], trst_gpio);
-
- command_print(CMD, "BCM2835 GPIO config: trst = %d", trst_gpio);
- return ERROR_OK;
-}
-
-COMMAND_HANDLER(bcm2835gpio_handle_swd_gpionums)
-{
- if (CMD_ARGC == 2) {
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[0], swclk_gpio);
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[1], swdio_gpio);
- } else if (CMD_ARGC != 0) {
- return ERROR_COMMAND_SYNTAX_ERROR;
- }
-
- command_print(CMD,
- "BCM2835 GPIO nums: swclk = %d, swdio = %d",
- swclk_gpio, swdio_gpio);
-
- return ERROR_OK;
-}
-
-COMMAND_HANDLER(bcm2835gpio_handle_swd_gpionum_swclk)
-{
- if (CMD_ARGC == 1)
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[0], swclk_gpio);
-
- command_print(CMD, "BCM2835 num: swclk = %d", swclk_gpio);
- return ERROR_OK;
-}
-
-COMMAND_HANDLER(bcm2835gpio_handle_swd_gpionum_swdio)
-{
- if (CMD_ARGC == 1)
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[0], swdio_gpio);
-
- command_print(CMD, "BCM2835 num: swdio = %d", swdio_gpio);
- return ERROR_OK;
-}
-
-COMMAND_HANDLER(bcm2835gpio_handle_swd_dir_gpionum_swdio)
-{
- if (CMD_ARGC == 1)
- COMMAND_PARSE_NUMBER(int, CMD_ARGV[0], swdio_dir_gpio);
-
- command_print(CMD, "BCM2835 num: swdio_dir = %d", swdio_dir_gpio);
- return ERROR_OK;
-}
-
COMMAND_HANDLER(bcm2835gpio_handle_speed_coeffs)
{
if (CMD_ARGC == 2) {
}
static const struct command_registration bcm2835gpio_subcommand_handlers[] = {
- {
- .name = "jtag_nums",
- .handler = &bcm2835gpio_handle_jtag_gpionums,
- .mode = COMMAND_CONFIG,
- .help = "gpio numbers for tck, tms, tdi, tdo. (in that order)",
- .usage = "[tck tms tdi tdo]",
- },
- {
- .name = "tck_num",
- .handler = &bcm2835gpio_handle_jtag_gpionum_tck,
- .mode = COMMAND_CONFIG,
- .help = "gpio number for tck.",
- .usage = "[tck]",
- },
- {
- .name = "tms_num",
- .handler = &bcm2835gpio_handle_jtag_gpionum_tms,
- .mode = COMMAND_CONFIG,
- .help = "gpio number for tms.",
- .usage = "[tms]",
- },
- {
- .name = "tdo_num",
- .handler = &bcm2835gpio_handle_jtag_gpionum_tdo,
- .mode = COMMAND_CONFIG,
- .help = "gpio number for tdo.",
- .usage = "[tdo]",
- },
- {
- .name = "tdi_num",
- .handler = &bcm2835gpio_handle_jtag_gpionum_tdi,
- .mode = COMMAND_CONFIG,
- .help = "gpio number for tdi.",
- .usage = "[tdi]",
- },
- {
- .name = "swd_nums",
- .handler = &bcm2835gpio_handle_swd_gpionums,
- .mode = COMMAND_CONFIG,
- .help = "gpio numbers for swclk, swdio. (in that order)",
- .usage = "[swclk swdio]",
- },
- {
- .name = "swclk_num",
- .handler = &bcm2835gpio_handle_swd_gpionum_swclk,
- .mode = COMMAND_CONFIG,
- .help = "gpio number for swclk.",
- .usage = "[swclk]",
- },
- {
- .name = "swdio_num",
- .handler = &bcm2835gpio_handle_swd_gpionum_swdio,
- .mode = COMMAND_CONFIG,
- .help = "gpio number for swdio.",
- .usage = "[swdio]",
- },
- {
- .name = "swdio_dir_num",
- .handler = &bcm2835gpio_handle_swd_dir_gpionum_swdio,
- .mode = COMMAND_CONFIG,
- .help = "gpio number for swdio direction control pin (set=output mode, clear=input mode)",
- .usage = "[swdio_dir]",
- },
- {
- .name = "srst_num",
- .handler = &bcm2835gpio_handle_jtag_gpionum_srst,
- .mode = COMMAND_CONFIG,
- .help = "gpio number for srst.",
- .usage = "[srst]",
- },
- {
- .name = "trst_num",
- .handler = &bcm2835gpio_handle_jtag_gpionum_trst,
- .mode = COMMAND_CONFIG,
- .help = "gpio number for trst.",
- .usage = "[trst]",
- },
{
.name = "speed_coeffs",
.handler = &bcm2835gpio_handle_speed_coeffs,
COMMAND_REGISTRATION_DONE
};
-static const char * const bcm2835_transports[] = { "jtag", "swd", NULL };
-
-static struct jtag_interface bcm2835gpio_interface = {
- .supported = DEBUG_CAP_TMS_SEQ,
- .execute_queue = bitbang_execute_queue,
-};
-
-struct adapter_driver bcm2835gpio_adapter_driver = {
- .name = "bcm2835gpio",
- .transports = bcm2835_transports,
- .commands = bcm2835gpio_command_handlers,
-
- .init = bcm2835gpio_init,
- .quit = bcm2835gpio_quit,
- .reset = bcm2835gpio_reset,
- .speed = bcm2835gpio_speed,
- .khz = bcm2835gpio_khz,
- .speed_div = bcm2835gpio_speed_div,
-
- .jtag_ops = &bcm2835gpio_interface,
- .swd_ops = &bitbang_swd,
-};
-
static bool bcm2835gpio_jtag_mode_possible(void)
{
- if (!is_gpio_valid(tck_gpio))
- return 0;
- if (!is_gpio_valid(tms_gpio))
- return 0;
- if (!is_gpio_valid(tdi_gpio))
- return 0;
- if (!is_gpio_valid(tdo_gpio))
- return 0;
- return 1;
+ if (!is_gpio_config_valid(ADAPTER_GPIO_IDX_TCK))
+ return false;
+ if (!is_gpio_config_valid(ADAPTER_GPIO_IDX_TMS))
+ return false;
+ if (!is_gpio_config_valid(ADAPTER_GPIO_IDX_TDI))
+ return false;
+ if (!is_gpio_config_valid(ADAPTER_GPIO_IDX_TDO))
+ return false;
+ return true;
}
static bool bcm2835gpio_swd_mode_possible(void)
{
- if (!is_gpio_valid(swclk_gpio))
- return 0;
- if (!is_gpio_valid(swdio_gpio))
- return 0;
- return 1;
+ if (!is_gpio_config_valid(ADAPTER_GPIO_IDX_SWCLK))
+ return false;
+ if (!is_gpio_config_valid(ADAPTER_GPIO_IDX_SWDIO))
+ return false;
+ return true;
}
static void bcm2835gpio_munmap(void)
}
}
+static struct bitbang_interface bcm2835gpio_bitbang = {
+ .read = bcm2835gpio_read,
+ .write = bcm2835gpio_write,
+ .swdio_read = bcm2835_swdio_read,
+ .swdio_drive = bcm2835_swdio_drive,
+ .swd_write = bcm2835gpio_swd_write_generic,
+ .blink = NULL
+};
+
static int bcm2835gpio_init(void)
{
- bitbang_interface = &bcm2835gpio_bitbang;
-
LOG_INFO("BCM2835 GPIO JTAG/SWD bitbang driver");
+ bitbang_interface = &bcm2835gpio_bitbang;
+ adapter_gpio_config = adapter_gpio_get_config();
+
if (transport_is_jtag() && !bcm2835gpio_jtag_mode_possible()) {
LOG_ERROR("Require tck, tms, tdi and tdo gpios for JTAG mode");
return ERROR_JTAG_INIT_FAILED;
/* set 4mA drive strength, slew rate limited, hysteresis on */
pads_base[BCM2835_PADS_GPIO_0_27_OFFSET] = 0x5a000008 + 1;
- /*
- * Configure TDO as an input, and TDI, TCK, TMS, TRST, SRST
- * as outputs. Drive TDI and TCK low, and TMS/TRST/SRST high.
+ /* Configure JTAG/SWD signals. Default directions and initial states are handled
+ * by adapter.c and "adapter gpio" command.
*/
if (transport_is_jtag()) {
- tdo_gpio_mode = MODE_GPIO(tdo_gpio);
- tdi_gpio_mode = MODE_GPIO(tdi_gpio);
- tck_gpio_mode = MODE_GPIO(tck_gpio);
- tms_gpio_mode = MODE_GPIO(tms_gpio);
-
- INP_GPIO(tdo_gpio);
-
- GPIO_CLR = 1<<tdi_gpio | 1<<tck_gpio;
- GPIO_SET = 1<<tms_gpio;
-
- OUT_GPIO(tdi_gpio);
- OUT_GPIO(tck_gpio);
- OUT_GPIO(tms_gpio);
-
- if (is_gpio_valid(trst_gpio)) {
- trst_gpio_mode = MODE_GPIO(trst_gpio);
- GPIO_SET = 1 << trst_gpio;
- OUT_GPIO(trst_gpio);
- }
+ initialize_gpio(ADAPTER_GPIO_IDX_TDO);
+ initialize_gpio(ADAPTER_GPIO_IDX_TDI);
+ initialize_gpio(ADAPTER_GPIO_IDX_TMS);
+ initialize_gpio(ADAPTER_GPIO_IDX_TCK);
+ initialize_gpio(ADAPTER_GPIO_IDX_TRST);
}
if (transport_is_swd()) {
- /* Make buffer an output before the GPIO connected to it */
- if (is_gpio_valid(swdio_dir_gpio)) {
- swdio_dir_gpio_mode = MODE_GPIO(swdio_dir_gpio);
- GPIO_SET = 1 << swdio_dir_gpio;
- OUT_GPIO(swdio_dir_gpio);
+ /* swdio and its buffer should be initialized in the order that prevents
+ * two outputs from being connected together. This will occur if the
+ * swdio GPIO of the AM335x is configured as an output while its
+ * external buffer is configured to send the swdio signal from the
+ * target to the AM335x.
+ */
+ if (adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].init_state == ADAPTER_GPIO_INIT_STATE_INPUT) {
+ initialize_gpio(ADAPTER_GPIO_IDX_SWDIO);
+ initialize_gpio(ADAPTER_GPIO_IDX_SWDIO_DIR);
+ } else {
+ initialize_gpio(ADAPTER_GPIO_IDX_SWDIO_DIR);
+ initialize_gpio(ADAPTER_GPIO_IDX_SWDIO);
}
- swclk_gpio_mode = MODE_GPIO(swclk_gpio);
- swdio_gpio_mode = MODE_GPIO(swdio_gpio);
-
- GPIO_CLR = 1<<swdio_gpio | 1<<swclk_gpio;
+ initialize_gpio(ADAPTER_GPIO_IDX_SWCLK);
- OUT_GPIO(swclk_gpio);
- OUT_GPIO(swdio_gpio);
- }
-
- if (is_gpio_valid(srst_gpio)) {
- srst_gpio_mode = MODE_GPIO(srst_gpio);
- GPIO_SET = 1 << srst_gpio;
- OUT_GPIO(srst_gpio);
+ if (adapter_gpio_config[ADAPTER_GPIO_IDX_SWCLK].drive == ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL &&
+ adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].drive == ADAPTER_GPIO_DRIVE_MODE_PUSH_PULL) {
+ LOG_DEBUG("BCM2835 GPIO using fast mode for SWD write");
+ bcm2835gpio_bitbang.swd_write = bcm2835gpio_swd_write_fast;
+ } else {
+ LOG_DEBUG("BCM2835 GPIO using generic mode for SWD write");
+ bcm2835gpio_bitbang.swd_write = bcm2835gpio_swd_write_generic;
+ }
}
- LOG_DEBUG("saved pinmux settings: tck %d tms %d tdi %d "
- "tdo %d trst %d srst %d", tck_gpio_mode, tms_gpio_mode,
- tdi_gpio_mode, tdo_gpio_mode, trst_gpio_mode, srst_gpio_mode);
+ initialize_gpio(ADAPTER_GPIO_IDX_SRST);
return ERROR_OK;
}
static int bcm2835gpio_quit(void)
{
if (transport_is_jtag()) {
- SET_MODE_GPIO(tdo_gpio, tdo_gpio_mode);
- SET_MODE_GPIO(tdi_gpio, tdi_gpio_mode);
- SET_MODE_GPIO(tck_gpio, tck_gpio_mode);
- SET_MODE_GPIO(tms_gpio, tms_gpio_mode);
- if (is_gpio_valid(trst_gpio))
- SET_MODE_GPIO(trst_gpio, trst_gpio_mode);
+ restore_gpio(ADAPTER_GPIO_IDX_TDO);
+ restore_gpio(ADAPTER_GPIO_IDX_TDI);
+ restore_gpio(ADAPTER_GPIO_IDX_TCK);
+ restore_gpio(ADAPTER_GPIO_IDX_TMS);
+ restore_gpio(ADAPTER_GPIO_IDX_TRST);
}
if (transport_is_swd()) {
- SET_MODE_GPIO(swclk_gpio, swclk_gpio_mode);
- SET_MODE_GPIO(swdio_gpio, swdio_gpio_mode);
+ /* Restore swdio/swdio_dir to their initial modes, even if that means
+ * connecting two outputs. Begin by making swdio an input so that the
+ * current and final states of swdio and swdio_dir do not have to be
+ * considered to calculate the safe restoration order.
+ */
+ INP_GPIO(adapter_gpio_config[ADAPTER_GPIO_IDX_SWDIO].gpio_num);
+ restore_gpio(ADAPTER_GPIO_IDX_SWDIO_DIR);
+ restore_gpio(ADAPTER_GPIO_IDX_SWDIO);
+ restore_gpio(ADAPTER_GPIO_IDX_SWCLK);
}
- if (is_gpio_valid(srst_gpio))
- SET_MODE_GPIO(srst_gpio, srst_gpio_mode);
-
- if (is_gpio_valid(swdio_dir_gpio))
- SET_MODE_GPIO(swdio_dir_gpio, swdio_dir_gpio_mode);
+ restore_gpio(ADAPTER_GPIO_IDX_SRST);
bcm2835gpio_munmap();
return ERROR_OK;
}
+
+
+static const char * const bcm2835_transports[] = { "jtag", "swd", NULL };
+
+static struct jtag_interface bcm2835gpio_interface = {
+ .supported = DEBUG_CAP_TMS_SEQ,
+ .execute_queue = bitbang_execute_queue,
+};
+struct adapter_driver bcm2835gpio_adapter_driver = {
+ .name = "bcm2835gpio",
+ .transports = bcm2835_transports,
+ .commands = bcm2835gpio_command_handlers,
+
+ .init = bcm2835gpio_init,
+ .quit = bcm2835gpio_quit,
+ .reset = bcm2835gpio_reset,
+ .speed = bcm2835gpio_speed,
+ .khz = bcm2835gpio_khz,
+ .speed_div = bcm2835gpio_speed_div,
+
+ .jtag_ops = &bcm2835gpio_interface,
+ .swd_ops = &bitbang_swd,
+};
projects / fw / openocd / blobdiff