All changes in the OpenOCD Git repository go through the web-based Gerrit
Code Review System:
-@uref{http://openocd.zylin.com/}
+@uref{https://review.openocd.org/}
After a one-time registration and repository setup, anyone can push commits
from their local Git repository directly into Gerrit.
Engine) mode built into many FTDI chips, such as the FT2232, FT4232 and FT232H.
The driver is using libusb-1.0 in asynchronous mode to talk to the FTDI device,
-bypassing intermediate libraries like libftdi or D2XX.
+bypassing intermediate libraries like libftdi.
Support for new FTDI based adapters can be added completely through
configuration files, without the need to patch and rebuild OpenOCD.
for FTDI chips. These interfaces have several commands, used to
configure the driver before initializing the JTAG scan chain:
-@deffn {Config Command} {usb_blaster device_desc} description
-Provides the USB device description (the @emph{iProduct string})
-of the FTDI FT245 device. If not
-specified, the FTDI default value is used. This setting is only valid
-if compiled with FTD2XX support.
-@end deffn
-
@deffn {Config Command} {usb_blaster vid_pid} vid pid
The vendor ID and product ID of the FTDI FT245 device. If not specified,
default values are used.
@deffn {Config Command} {st-link vid_pid} [vid pid]+
Pairs of vendor IDs and product IDs of the device.
@end deffn
+
+@deffn {Command} {st-link cmd} rx_n (tx_byte)+
+Sends an arbitrary command composed by the sequence of bytes @var{tx_byte}
+and receives @var{rx_n} bytes.
+
+For example, the command to read the target's supply voltage is one byte 0xf7 followed
+by 15 bytes zero. It returns 8 bytes, where the first 4 bytes represent the ADC sampling
+of the reference voltage 1.2V and the last 4 bytes represent the ADC sampling of half
+the target's supply voltage.
+@example
+> st-link cmd 8 0xf7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+0xf1 0x05 0x00 0x00 0x0b 0x08 0x00 0x00
+@end example
+The result can be converted to Volts (ignoring the most significant bytes, always zero)
+@example
+> set a [st-link cmd 8 0xf7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0]
+> echo [expr 2*1.2*([lindex $a 4]+256*[lindex $a 5])/([lindex $a 0]+256*[lindex $a 1])]
+3.24891518738
+@end example
+@end deffn
@end deffn
@deffn {Interface Driver} {opendous}
peripherals' kernel drivers. The driver restores the previous
configuration on exit.
+GPIO numbers >= 32 can't be used for performance reasons.
+
See @file{interface/raspberrypi-native.cfg} for a sample config and
pinout.
functionality is available through the @command{flash write_bank},
@command{flash read_bank}, and @command{flash verify_bank} commands.
+According to device size, 1- to 4-byte addresses are sent. However, some
+flash chips additionally have to be switched to 4-byte addresses by an extra
+command, see below.
+
@itemize
@item @var{ir} ... is loaded into the JTAG IR to map the flash as the JTAG DR.
For the bitstreams generated from @file{xilinx_bscan_spi.py} this is the
flash bank $_FLASHNAME spi 0x0 0 0 0 \
$_TARGETNAME $_XILINX_USER1
@end example
+
+@deffn Command {jtagspi set} bank_id name total_size page_size read_cmd unused pprg_cmd mass_erase_cmd sector_size sector_erase_cmd
+Sets flash parameters: @var{name} human readable string, @var{total_size}
+size in bytes, @var{page_size} is write page size. @var{read_cmd} and @var{pprg_cmd}
+are commands for read and page program, respectively. @var{mass_erase_cmd},
+@var{sector_size} and @var{sector_erase_cmd} are optional.
+@example
+jtagspi set 0 w25q128 0x1000000 0x100 0x03 0 0x02 0xC7 0x10000 0xD8
+@end example
+@end deffn
+
+@deffn Command {jtagspi cmd} bank_id resp_num cmd_byte ...
+Sends command @var{cmd_byte} and at most 20 following bytes and reads
+@var{resp_num} bytes afterwards. E.g. for 'Enter 4-byte address mode'
+@example
+jtagspi cmd 0 0 0xB7
+@end example
+@end deffn
+
+@deffn Command {jtagspi always_4byte} bank_id [ on | off ]
+Some devices use 4-byte addresses for all commands except the legacy 0x03 read
+regardless of device size. This command controls the corresponding hack.
+@end deffn
@end deffn
@deffn {Flash Driver} {xcf}
@end deffn
+@deffn {Flash Driver} {npcx}
+All versions of the NPCX microcontroller families from Nuvoton include internal
+flash. The NPCX flash driver supports the NPCX family of devices. The driver
+automatically recognizes the specific version's flash parameters and
+autoconfigures itself. The flash bank starts at address 0x64000000.
+
+@example
+flash bank $_FLASHNAME npcx 0x64000000 0 0 0 $_TARGETNAME
+@end example
+@end deffn
+
@deffn {Flash Driver} {nrf5}
All members of the nRF51 microcontroller families from Nordic Semiconductor
include internal flash and use ARM Cortex-M0 core.
@deffn {Flash Driver} {stm32f1x}
All members of the STM32F0, STM32F1 and STM32F3 microcontroller families
-from STMicroelectronics and all members of the GD32F1x0 and GD32F3x0 microcontroller
-families from GigaDevice include internal flash and use ARM Cortex-M0/M3/M4 cores.
+from STMicroelectronics and all members of the GD32F1x0, GD32F3x0 and GD32E23x microcontroller
+families from GigaDevice include internal flash and use ARM Cortex-M0/M3/M4/M23 cores.
The driver automatically recognizes a number of these chips using
the chip identification register, and autoconfigures itself.
@end deffn
@deffn {Flash Driver} {stm32l4x}
-All members of the STM32 G0, G4, L4, L4+, L5, WB and WL
+All members of the STM32 G0, G4, L4, L4+, L5, U5, WB and WL
microcontroller families from STMicroelectronics include internal flash
and use ARM Cortex-M0+, M4 and M33 cores.
The driver automatically recognizes a number of these chips using
@deffn {Command} {stm32l4x lock} num
Locks the entire stm32 device.
The @var{num} parameter is a value shown by @command{flash banks}.
+
+@emph{Note:} To apply the protection change immediately, use @command{stm32l4x option_load}.
@end deffn
@deffn {Command} {stm32l4x unlock} num
Unlocks the entire stm32 device.
The @var{num} parameter is a value shown by @command{flash banks}.
+
+@emph{Note:} To apply the protection change immediately, use @command{stm32l4x option_load}.
@end deffn
@deffn {Command} {stm32l4x mass_erase} num
is the register offset of the Option byte to write, and @var{reg_mask} is the mask
to apply when writing the register (only bits with a '1' will be touched).
+@emph{Note:} To apply the option bytes change immediately, use @command{stm32l4x option_load}.
+
For example to write the WRP1AR option bytes:
@example
stm32l4x option_write 0 0x28 0x00FF0000 0x00FF00FF
Forces a re-load of the option byte registers. Will cause a system reset of the device.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
+
+@deffn Command {stm32l4x trustzone} num [@option{enable} | @option{disable}]
+Enables or disables Global TrustZone Security, using the TZEN option bit.
+If neither @option{enabled} nor @option{disable} are specified, the command will display
+the TrustZone status.
+@emph{Note:} This command works only with devices with TrustZone, eg. STM32L5.
+@emph{Note:} This command will perform an OBL_Launch after modifying the TZEN.
+@end deffn
@end deffn
@deffn {Flash Driver} {str7x}
projects / fw / openocd / blobdiff