# apt-get install flex bison libgmp3-dev libmpfr-dev libncurses5-dev \
# libmpc-dev autoconf texinfo build-essential
#
+# Or on Ubuntu Maverick give `apt-get build-dep gcc-4.5` a try.
+#
+
+# Stop if any command fails
+set -e
+##############################################################################
+# Settings section
+# You probably want to customize those
+##############################################################################
TARGET=arm-none-eabi # Or: TARGET=arm-elf
PREFIX=${HOME}/arm-none-eabi # Install location of your final toolchain
-PARALLEL="" # Or: PARALLEL="-j 5" for 4 CPUs
+PARALLEL= # Or: PARALLEL="-j 5" for 4 CPUs
DARWIN_OPT_PATH=/opt/local # Path in which MacPorts or Fink is installed
+# Set to 'sudo' if you need superuser privileges while installing
+SUDO=
+# Set to 1 to be quieter while running
+QUIET=0
+# Set to 1 to use linaro gcc instead of the FSF gcc
+USE_LINARO=0
+# Set to 1 to build libstm32 provided by ST
+LIBSTM32_EN=0
+# Set to 1 to build libopenstm32 an open source library for stm32
+LIBOPENSTM32_EN=0
+# Make the gcc default to Cortex-M3
+DEFAULT_TO_CORTEX_M3=0
+
+##############################################################################
+# Version and download url settings section
+##############################################################################
+if [ ${USE_LINARO} == 0 ] ; then
+ # For FSF GCC:
+ GCCVERSION=4.5.1
+ GCC=gcc-${GCCVERSION}
+ GCCURL=http://ftp.gnu.org/gnu/gcc/${GCC}/${GCC}.tar.gz
+else
+ # For the Linaro GCC:
+ GCCVERSION=4.5-2010.08-1
+ GCC=gcc-linaro-${GCCVERSION}
+ GCCURL=http://launchpad.net/gcc-linaro/4.5/${GCCVERSION}/+download/${GCC}.tar.gz
+fi
BINUTILS=binutils-2.20
-GCC=gcc-4.5.1
NEWLIB=newlib-1.18.0
GDB=gdb-7.2
LIBCMSIS=v1.10-2
LIBSTM32=v3.0.0-1
LIBSTM32USB=v3.0.1-1
LIBOPENSTM32=master
-LIBSTM32_EN=0
-LIBOPENSTM32_EN=0
+
+##############################################################################
+# Flags section
+##############################################################################
+
+GDBFLAGS=
+BINUTILFLAGS=
+
+if [ ${DEFAULT_TO_CORTEX_M3} == 0 ] ; then
+ GCCFLAGS=
+else
+ # To default to the Cortex-M3:
+ GCCFLAGS="--with-arch=armv7-m --with-mode=thumb"
+fi
+
+# Pull in the local configuration, if any
+if [ -f local.sh ]; then
+ . ./local.sh
+fi
+
+MAKEFLAGS=${PARALLEL}
+TARFLAGS=v
+
+if [ ${QUIET} != 0 ]; then
+ TARFLAGS=
+ MAKEFLAGS="${MAKEFLAGS} -s"
+fi
+
+export PATH="${PREFIX}/bin:${PATH}"
SUMMON_DIR=$(pwd)
SOURCES=${SUMMON_DIR}/sources
+STAMPS=${SUMMON_DIR}/stamps
-export PATH="${PREFIX}/bin:${PATH}"
+##############################################################################
+# Building section
+# You probably don't have to touch anything after this
+##############################################################################
-GCCFLAGS=
-GDBFLAGS=
-BINUTILFLAGS=
+# Fetch a versioned file from a URL
+function fetch {
+ if [ ! -e ${STAMPS}/$1.fetch ]; then
+ log "Downloading $1 sources..."
+ wget -c --no-passive-ftp $2
+ touch ${STAMPS}/$1.fetch
+ fi
+}
+
+# Log a message out to the console
+function log {
+ echo "******************************************************************"
+ echo "* $*"
+ echo "******************************************************************"
+}
+
+# Unpack an archive
+function unpack {
+ log Unpacking $*
+ # Use 'auto' mode decompression. Replace with a switch if tar doesn't support -a
+ tar xaf${TARFLAGS} ${SOURCES}/$1.tar.*
+}
+
+# Install a build
+function install {
+ log $1
+ ${SUDO} make ${MAKEFLAGS} $2 $3 $4 $5 $6 $7 $8
+}
case "$(uname)" in
Linux)
;;
Darwin)
echo "Found Darwin OS."
- GCCFLAGS="--with-gmp=${DARWIN_OPT_PATH} \
+ GCCFLAGS="${GCCFLAGS} \
+ --with-gmp=${DARWIN_OPT_PATH} \
--with-mpfr=${DARWIN_OPT_PATH} \
--with-mpc=${DARWIN_OPT_PATH} \
-with-libiconv-prefix=${DARWIN_OPT_PATH}"
;;
esac
-if [ ! -e ${SOURCES} ]; then
- mkdir ${SOURCES}
-fi
+mkdir -p ${STAMPS} ${SOURCES}
cd ${SOURCES}
-echo "Downloading binutils sources..."
-wget -c http://ftp.gnu.org/gnu/binutils/${BINUTILS}.tar.bz2
-
-echo "Downloading gcc sources..."
-wget -c http://ftp.gnu.org/gnu/gcc/${GCC}/${GCC}.tar.bz2
-
-echo "Downloading newlib sources..."
-wget -c --no-passive-ftp ftp://sources.redhat.com/pub/newlib/${NEWLIB}.tar.gz
-
-echo "Downloading gdb sources..."
-wget -c http://ftp.gnu.org/gnu/gdb/${GDB}.tar.bz2
+fetch ${BINUTILS} http://ftp.gnu.org/gnu/binutils/${BINUTILS}.tar.bz2
+fetch ${GCC} ${GCCURL}
+fetch ${NEWLIB} ftp://sources.redhat.com/pub/newlib/${NEWLIB}.tar.gz
+fetch ${GDB} http://ftp.gnu.org/gnu/gdb/${GDB}.tar.bz2
if [ ${LIBSTM32_EN} != 0 ]; then
if [ ! -e libcmsis-${LIBCMSIS}.tar.bz2 ]; then
- echo "Cloning libcmsis sources..."
+ log "Cloning libcmsis sources..."
git clone git://git.open-bldc.org/libcmsis.git
cd libcmsis
git archive --format=tar --prefix=libcmsis-${LIBCMSIS}/ ${LIBCMSIS} | \
fi
if [ ! -e libstm32-${LIBSTM32}.tar.bz2 ]; then
- echo "Cloning libstm32 sources..."
+ log "Cloning libstm32 sources..."
git clone git://git.open-bldc.org/libstm32.git
cd libstm32
git archive --format=tar --prefix=libstm32-${LIBSTM32}/ ${LIBSTM32} | \
fi
if [ ! -e libstm32usb-${LIBSTM32USB}.tar.bz2 ]; then
- echo "Cloning libstm32usb sources..."
+ log "Cloning libstm32usb sources..."
git clone git://git.open-bldc.org/libstm32usb.git
cd libstm32usb
git archive --format=tar --prefix=libstm32usb-${LIBSTM32USB}/ ${LIBSTM32USB} | \
if [ ${LIBOPENSTM32_EN} != 0 ]; then
if [ ! -e libopenstm32-${LIBOPENSTM32}.tar.bz2 ]; then
- echo "Cloning libopenstm32 sources..."
+ log "Cloning libopenstm32 sources..."
git clone git://libopenstm32.git.sourceforge.net/gitroot/libopenstm32/libopenstm32
cd libopenstm32
git archive --format=tar --prefix=libopenstm32-${LIBOPENSTM32}/ ${LIBOPENSTM32} | \
mkdir build
fi
-if [ ! -e .${BINUTILS}.build ]; then
- echo "******************************************************************"
- echo "* Unpacking ${BINUTILS}"
- echo "******************************************************************"
- tar xfvj ${SOURCES}/${BINUTILS}.tar.bz2
+if [ ! -e ${STAMPS}/${BINUTILS}.build ]; then
+ unpack ${BINUTILS}
cd build
- echo "******************************************************************"
- echo "* Configuring ${BINUTILS}"
- echo "******************************************************************"
+ log "Configuring ${BINUTILS}"
../${BINUTILS}/configure --target=${TARGET} \
--prefix=${PREFIX} \
--enable-interwork \
--with-gnu-ld \
--disable-nls \
--disable-werror \
- ${BINUTILFLAGS} || exit
- echo "******************************************************************"
- echo "* Building ${BINUTILS}"
- echo "******************************************************************"
- make ${PARALLEL} || exit
- echo "******************************************************************"
- echo "* Installing ${BINUTILS}"
- echo "******************************************************************"
- make install || exit
+ ${BINUTILFLAGS}
+ log "Building ${BINUTILS}"
+ make ${MAKEFLAGS}
+ install ${BINUTILS} install
cd ..
- echo "******************************************************************"
- echo "* Cleaning up ${BINUTILS}"
- echo "******************************************************************"
- touch .${BINUTILS}.build
+ log "Cleaning up ${BINUTILS}"
+ touch ${STAMPS}/${BINUTILS}.build
rm -rf build/* ${BINUTILS}
fi
-if [ ! -e .${GCC}-boot.build ]; then
- echo "******************************************************************"
- echo "* Unpacking ${GCC}-boot"
- echo "******************************************************************"
- tar xfvj ${SOURCES}/${GCC}.tar.bz2
+if [ ! -e ${STAMPS}/${GCC}-boot.build ]; then
+ unpack ${GCC} boot
cd build
- echo "******************************************************************"
- echo "* Configuring ${GCC}-boot"
- echo "******************************************************************"
+ log "Configuring ${GCC}-boot"
../${GCC}/configure --target=${TARGET} \
--prefix=${PREFIX} \
--enable-interwork \
--with-gnu-ld \
--disable-nls \
--disable-werror \
- ${GCCFLAGS} || exit
- echo "******************************************************************"
- echo "* Building ${GCC}-boot"
- echo "******************************************************************"
- make ${PARALLEL} all-gcc || exit
- echo "******************************************************************"
- echo "* Installing ${GCC}-boot"
- echo "******************************************************************"
- make install-gcc || exit
+ ${GCCFLAGS}
+ log "Building ${GCC}-boot"
+ make ${MAKEFLAGS} all-gcc
+ install ${GCC}-boot install-gcc
cd ..
- echo "******************************************************************"
- echo "* Cleaning up ${GCC}-boot"
- echo "******************************************************************"
- touch .${GCC}-boot.build
+ log "Cleaning up ${GCC}-boot"
+ touch ${STAMPS}/${GCC}-boot.build
rm -rf build/* ${GCC}
fi
-if [ ! -e .${NEWLIB}.build ]; then
- echo "******************************************************************"
- echo "* Unpacking ${NEWLIB}"
- echo "******************************************************************"
- tar xfvz ${SOURCES}/${NEWLIB}.tar.gz
+if [ ! -e ${STAMPS}/${NEWLIB}.build ]; then
+ unpack ${NEWLIB}
cd build
- echo "******************************************************************"
- echo "* Configuring ${NEWLIB}"
- echo "******************************************************************"
+ log "Configuring ${NEWLIB}"
../${NEWLIB}/configure --target=${TARGET} \
--prefix=${PREFIX} \
--enable-interwork \
--with-gnu-ld \
--disable-nls \
--disable-werror \
- --disable-newlib-supplied-syscalls || exit
- echo "******************************************************************"
- echo "* Building ${NEWLIB}"
- echo "******************************************************************"
- make ${PARALLEL} || exit
- echo "******************************************************************"
- echo "* Installing ${NEWLIB}"
- echo "******************************************************************"
- make install || exit
+ --disable-newlib-supplied-syscalls
+ log "Building ${NEWLIB}"
+ make ${MAKEFLAGS}
+ install ${NEWLIB} install
cd ..
- echo "******************************************************************"
- echo "* Cleaning up ${NEWLIB}"
- echo "******************************************************************"
- touch .${NEWLIB}.build
+ log "Cleaning up ${NEWLIB}"
+ touch ${STAMPS}/${NEWLIB}.build
rm -rf build/* ${NEWLIB}
fi
# Yes, you need to build gcc again!
-if [ ! -e .${GCC}.build ]; then
- echo "******************************************************************"
- echo "* Unpacking ${GCC}"
- echo "******************************************************************"
- tar xfvj ${SOURCES}/${GCC}.tar.bz2
+if [ ! -e ${STAMPS}/${GCC}.build ]; then
+ unpack ${GCC}
cd build
- echo "******************************************************************"
- echo "* Configuring ${GCC}"
- echo "******************************************************************"
+ log "Configuring ${GCC}"
../${GCC}/configure --target=${TARGET} \
--prefix=${PREFIX} \
--enable-interwork \
--with-gnu-ld \
--disable-nls \
--disable-werror \
- ${GCCFLAGS} || exit
- echo "******************************************************************"
- echo "* Building ${GCC}"
- echo "******************************************************************"
- make ${PARALLEL} || exit
- echo "******************************************************************"
- echo "* Installing ${GCC}"
- echo "******************************************************************"
- make install || exit
+ ${GCCFLAGS}
+ log "Building ${GCC}"
+ make ${MAKEFLAGS}
+ install ${GCC} install
cd ..
- echo "******************************************************************"
- echo "* Cleaning up ${GCC}"
- echo "******************************************************************"
- touch .${GCC}.build
+ log "Cleaning up ${GCC}"
+ touch ${STAMPS}/${GCC}.build
rm -rf build/* ${GCC}
fi
-if [ ! -e .${GDB}.build ]; then
- echo "******************************************************************"
- echo "* Unpacking ${GDB}"
- echo "******************************************************************"
- tar xfvj ${SOURCES}/${GDB}.tar.bz2
+if [ ! -e ${STAMPS}/${GDB}.build ]; then
+ unpack ${GDB}
cd build
- echo "******************************************************************"
- echo "* Configuring ${GDB}"
- echo "******************************************************************"
+ log "Configuring ${GDB}"
../${GDB}/configure --target=${TARGET} \
--prefix=${PREFIX} \
--enable-interwork \
--enable-multilib \
--disable-werror \
- ${GDBFLAGS} || exit
- echo "******************************************************************"
- echo "* Building ${GDB}"
- echo "******************************************************************"
- make ${PARALLEL} || exit
- echo "******************************************************************"
- echo "* Installing ${GDB}"
- echo "******************************************************************"
- make install || exit
+ ${GDBFLAGS}
+ log "Building ${GDB}"
+ make ${MAKEFLAGS}
+ install ${GDB} install
cd ..
- echo "******************************************************************"
- echo "* Cleaning up ${GDB}"
- echo "******************************************************************"
- touch .${GDB}.build
+ log "Cleaning up ${GDB}"
+ touch ${STAMPS}/${GDB}.build
rm -rf build/* ${GDB}
fi
if [ ${LIBSTM32_EN} != 0 ]; then
if [ ! -e .libcmsis-${LIBCMSIS}.build ]; then
- echo "******************************************************************"
- echo "* Unpacking libcmsis-${LIBCMSIS}"
- echo "******************************************************************"
- tar xfvj ${SOURCES}/libcmsis-${LIBCMSIS}.tar.bz2
+ unpack libcmsis-${LIBCMSIS}
cd libcmsis-${LIBCMSIS}
- echo "******************************************************************"
- echo "* Building libcmsis-${LIBCMSIS}"
- echo "******************************************************************"
- make arch_prefix=${TARGET} prefix=${PREFIX} || exit
- echo "******************************************************************"
- echo "* Installing libcmsis-${LIBCMSIS}"
- echo "******************************************************************"
- make arch_prefix=${TARGET} prefix=${PREFIX} install || exit
+ log "Building libcmsis-${LIBCMSIS}"
+ make arch_prefix=${TARGET} prefix=${PREFIX}
+ install libcmsis-${LIBCMSIS} arch_prefix=${TARGET} prefix=${PREFIX} install
cd ..
- echo "******************************************************************"
- echo "* Cleaning up libcmsis-${LIBCMSIS}"
- echo "******************************************************************"
+ log "Cleaning up libcmsis-${LIBCMSIS}"
touch .libcmsis-${LIBCMSIS}.build
rm -rf libcmsis-${LIBCMSIS}
fi
if [ ! -e .libstm32-${LIBSTM32}.build ]; then
- echo "******************************************************************"
- echo "* Unpacking libstm32-${LIBSTM32}"
- echo "******************************************************************"
- tar xfvj ${SOURCES}/libstm32-${LIBSTM32}.tar.bz2
+ unpack libstm32-${LIBSTM32}
cd libstm32-${LIBSTM32}
- echo "******************************************************************"
- echo "* Building libstm32-${LIBSTM32}"
- echo "******************************************************************"
- make arch_prefix=${TARGET} prefix=${PREFIX} || exit
- echo "******************************************************************"
- echo "* Installing libstm32-${LIBSTM32}"
- echo "******************************************************************"
- make arch_prefix=${TARGET} prefix=${PREFIX} install || exit
+ log "Building libstm32-${LIBSTM32}"
+ make arch_prefix=${TARGET} prefix=${PREFIX}
+ install libstm32-${LIBSTM32} arch_prefix=${TARGET} prefix=${PREFIX} install
cd ..
- echo "******************************************************************"
- echo "* Cleaning up libstm32-${LIBSTM32}"
- echo "******************************************************************"
+ log "Cleaning up libstm32-${LIBSTM32}"
touch .libstm32-${LIBSTM32}.build
rm -rf libstm32-${LIBSTM32}
fi
if [ ! -e .libstm32usb-${LIBSTM32USB}.build ]; then
- echo "******************************************************************"
- echo "* Unpacking libstm32usb-${LIBSTM32USB}"
- echo "******************************************************************"
- tar xfvj ${SOURCES}/libstm32usb-${LIBSTM32USB}.tar.bz2
+ unpack libstm32usb-${LIBSTM32USB}
cd libstm32usb-${LIBSTM32USB}
- echo "******************************************************************"
- echo "* Building libstm32usb-${LIBSTM32USB}"
- echo "******************************************************************"
- make arch_prefix=${TARGET} prefix=${PREFIX} || exit
- echo "******************************************************************"
- echo "* Installing libstm32usb-${LIBSTM32USB}"
- echo "******************************************************************"
- make arch_prefix=${TARGET} prefix=${PREFIX} install || exit
+ log "Building libstm32usb-${LIBSTM32USB}"
+ make arch_prefix=${TARGET} prefix=${PREFIX}
+ install libstm32usb-${LIBSTM32USB} arch_prefix=${TARGET} prefix=${PREFIX} install
cd ..
- echo "******************************************************************"
- echo "* Cleaning up libstm32usb-${LIBSTM32USB}"
- echo "******************************************************************"
+ log "Cleaning up libstm32usb-${LIBSTM32USB}"
touch .libstm32usb-${LIBSTM32USB}.build
rm -rf libstm32usb-${LIBSTM32USB}
fi
fi
if [ $LIBOPENSTM32_EN != 0 ]; then
- echo "******************************************************************"
- echo "* Unpacking libopenstm32-${LIBOPENSTM32}"
- echo "******************************************************************"
- tar xfvj ${SOURCES}/libopenstm32-${LIBOPENSTM32}.tar.bz2
+ unpack libopenstm32-${LIBOPENSTM32}
cd libopenstm32-${LIBOPENSTM32}
- echo "******************************************************************"
- echo "* Building libopenstm32-${LIBOPENSTM32}"
- echo "******************************************************************"
- make PREFIX=${TARGET} DESTDIR=${PREFIX} || exit
- echo "******************************************************************"
- echo "* Installing libopenstm32-${LIBOPENSTM32}"
- echo "******************************************************************"
- make PREFIX=${TARGET} DESTDIR=${PREFIX} install || exit
+ log "Building libopenstm32-${LIBOPENSTM32}"
+ make PREFIX=${TARGET} DESTDIR=${PREFIX}
+ install libopenstm32-${LIBOPENSTM32} PREFIX=${TARGET} DESTDIR=${PREFIX} install
cd ..
- echo "******************************************************************"
- echo "* Cleaning up libopenstm32-${LIBOPENSTM32}"
- echo "******************************************************************"
+ log "Cleaning up libopenstm32-${LIBOPENSTM32}"
touch .libopenstm32-${LIBOPENSTM32}.build
rm -rf libopenstm32-${LIBOPENSTM32}
fi
projects / fw / cortex-toolchain / blobdiff