</para>
</legalnotice>
<revhistory>
+ <revision>
+ <revnumber>1.3.1</revnumber>
+ <date>21 January 2014</date>
+ <revremark>
+ Bug fixes for TeleMega and TeleMetrum v2.0 along with a few
+ small UI improvements.
+ </revremark>
+ </revision>
<revision>
<revnumber>1.3</revnumber>
<date>12 November 2013</date>
rocket as it heads towards apogee.
</para>
<para>
- The height, speed and acceleration are shown along with the
- maximum values for each of them. This allows you to quickly
- answer the most commonly asked questions you'll hear during
- flight.
+ The height, speed, acceleration and tilt are shown along
+ with the maximum values for each of them. This allows you to
+ quickly answer the most commonly asked questions you'll hear
+ during flight.
</para>
<para>
The current latitude and longitude reported by the GPS are
<para>
Selecting the 'Fire Igniter' button brings up the usual device
selection dialog. Pick the desired device. This brings up another
- window which shows the current continuity test status for both
- apogee and main charges.
+ window which shows the current continuity test status for all
+ of the pyro channels.
</para>
<para>
Next, select the desired igniter to fire. This will enable the
Then, divide 434.550 MHz by the
measured frequency and multiply by the current radio cal value show
in the 'c s' command. For an unprogrammed board, the default value
- is 1186611. Take the resulting integer and program it using the 'c f'
+ is 1186611 for cc1111 based products and 7119667 for cc1120
+ based products. Take the resulting integer and program it using the 'c f'
command. Testing with the 'C' command again should show a carrier
within a few tens of Hertz of the intended frequency.
As with all 'c' sub-commands, follow this with a 'c w' to write the
- change to the parameter block in the on-board DataFlash chip.
+ change to the configuration memory.
</para>
<para>
Note that the 'reboot' command, which is very useful on the altimeters,
</appendix>
<appendix>
<title>Release Notes</title>
+ <simplesect>
+ <title>Version 1.3.1</title>
+ <xi:include
+ xmlns:xi="http://www.w3.org/2001/XInclude"
+ href="release-notes-1.3.1.xsl"
+ xpointer="xpointer(/article/*)"/>
+ </simplesect>
<simplesect>
<title>Version 1.3</title>
<xi:include
--- /dev/null
+<?xml version="1.0" encoding="utf-8" ?>
+<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook XML V4.5//EN"
+"/usr/share/xml/docbook/schema/dtd/4.5/docbookx.dtd">
+
+<article>
+ <para>
+ Version 1.3.1 is a minor release. It improves support for TeleMega,
+ TeleMetrum v2.0, TeleMini v2.0 and EasyMini.
+ </para>
+ <para>
+ AltOS Firmware Changes
+ <itemizedlist>
+ <listitem>
+ <para>
+ Improve sensor boot code. If sensors fail to self-test, the
+ device will still boot up and check for pad/idle modes. If
+ in idle mode, the device will warn the user with a distinct
+ beep, if in Pad mode, the unit will operate as best it
+ can. Also, the Z-axis accelerometer now uses the factory
+ calibration values instead of re-calibrating on the pad each
+ time. This avoids accidental boost detect when moving the
+ device around while in Pad mode.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Fix antenna-down mode accelerometer configuration. Antenna
+ down mode wasn't working because the accelerometer
+ calibration values were getting re-computed incorrectly in
+ inverted mode.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Improved APRS mode. Now uses compressed position format for
+ smaller data size, improved precision and to include
+ altitude data as well as latitude and longitude. Also added
+ battery and pyro voltage reports in the APRS comment field
+ so you can confirm that the unit is ready for launch.
+ </para>
+ </listitem>
+ </itemizedlist>
+ </para>
+ <para>
+ AltosUI changes
+ <itemizedlist>
+ <listitem>
+ <para>
+ Display additional TeleMega sensor values in real
+ units. Make all of these values available for
+ plotting. Display TeleMega orientation value in the Ascent
+ and Table tabs.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Support additional TeleMega pyro channels in the Fire
+ Igniter dialog. This lets you do remote testing of all of
+ the channels, rather than just Apogee and Main.
+ </para>
+ </listitem>
+ <listitem>
+ <para>
+ Limit data rate when downloading satellite images from
+ Google to make sure we stay within their limits so that all
+ of the map tiles download successfully.
+ </para>
+ </listitem>
+ </itemizedlist>
+ </para>
+</article>