X-Git-Url: https://git.gag.com/?p=fw%2Faltos;a=blobdiff_plain;f=doc%2Faltusmetrum.xsl;h=3022b8e3ff708b2c467942e4d81e91732c7fead7;hp=0430bc9410ab3104ae2ea574a67c9f5dd7db03a4;hb=7acd0cf17c5ca7a00893f35c7fe9c657389070e0;hpb=8bb6dd75a602792936d623713fb009fea25ef491;ds=inline
diff --git a/doc/altusmetrum.xsl b/doc/altusmetrum.xsl
index 0430bc94..3022b8e3 100644
--- a/doc/altusmetrum.xsl
+++ b/doc/altusmetrum.xsl
@@ -1793,35 +1793,47 @@ NAR #88757, TRA #12200
At the bottom of the dialog, there are four buttons:
-
-
-
- Save. This writes any changes to the
- configuration parameter block in flash memory. If you don't
- press this button, any changes you make will be lost.
-
-
-
-
- Reset. This resets the dialog to the most recently saved values,
- erasing any changes you have made.
-
-
-
-
- Reboot. This reboots the device. Use this to
- switch from idle to pad mode by rebooting once the rocket is
- oriented for flight, or to confirm changes you think you saved
- are really saved.
-
-
-
-
- Close. This closes the dialog. Any unsaved changes will be
- lost.
-
-
-
+
+
+ Save
+
+
+ This writes any changes to the
+ configuration parameter block in flash memory. If you don't
+ press this button, any changes you make will be lost.
+
+
+
+
+ Reset
+
+
+ This resets the dialog to the most recently saved values,
+ erasing any changes you have made.
+
+
+
+
+ Reboot
+
+
+ This reboots the device. Use this to
+ switch from idle to pad mode by rebooting once the rocket is
+ oriented for flight, or to confirm changes you think you saved
+ are really saved.
+
+
+
+
+ Close
+
+
+ This closes the dialog. Any unsaved changes will be
+ lost.
+
+
+
+
The rest of the dialog contains the parameters to be configured.
@@ -1913,32 +1925,41 @@ NAR #88757, TRA #12200
computers. This configuration parameter allows the two
channels to be used in different configurations.
-
-
-
- Dual Deploy. This is the usual mode of operation; the
- 'apogee' channel is fired at apogee and the 'main'
- channel at the height above ground specified by the
- 'Main Deploy Altitude' during descent.
-
-
-
-
- Redundant Apogee. This fires both channels at
- apogee, the 'apogee' channel first followed after a two second
- delay by the 'main' channel.
-
-
-
-
- Redundant Main. This fires both channels at the
- height above ground specified by the Main Deploy
- Altitude setting during descent. The 'apogee'
- channel is fired first, followed after a two second
- delay by the 'main' channel.
-
-
-
+
+
+ Dual Deploy
+
+
+ This is the usual mode of operation; the
+ 'apogee' channel is fired at apogee and the 'main'
+ channel at the height above ground specified by the
+ 'Main Deploy Altitude' during descent.
+
+
+
+
+ Redundant Apogee
+
+
+ This fires both channels at
+ apogee, the 'apogee' channel first followed after a two second
+ delay by the 'main' channel.
+
+
+
+
+ Redundant Main
+
+
+ This fires both channels at the
+ height above ground specified by the Main Deploy
+ Altitude setting during descent. The 'apogee'
+ channel is fired first, followed after a two second
+ delay by the 'main' channel.
+
+
+
+
Pad Orientation
@@ -1949,22 +1970,28 @@ NAR #88757, TRA #12200
parameter allows that default to be changed, permitting the
board to be mounted with the antenna pointing aft instead.
-
-
-
- Antenna Up. In this mode, the antenna end of the
- TeleMetrum board must point forward, in line with the
- expected flight path.
-
-
-
-
- Antenna Down. In this mode, the antenna end of the
- TeleMetrum board must point aft, in line with the
- expected flight path.
-
-
-
+
+
+ Antenna Up
+
+
+ In this mode, the antenna end of the
+ TeleMetrum board must point forward, in line with the
+ expected flight path.
+
+
+
+
+ Antenna Down
+
+
+ In this mode, the antenna end of the
+ TeleMetrum board must point aft, in line with the
+ expected flight path.
+
+
+
+
Configure Pyro Channels
@@ -2111,27 +2138,36 @@ NAR #88757, TRA #12200
At the bottom of the dialog, there are three buttons:
-
-
-
- Save. This writes any changes to the
- local Java preferences file. If you don't
- press this button, any changes you make will be lost.
-
-
-
-
- Reset. This resets the dialog to the most recently saved values,
- erasing any changes you have made.
-
-
-
-
- Close. This closes the dialog. Any unsaved changes will be
- lost.
-
-
-
+
+
+ Save
+
+
+ This writes any changes to the
+ local Java preferences file. If you don't
+ press this button, any changes you make will be lost.
+
+
+
+
+ Reset
+
+
+ This resets the dialog to the most recently saved values,
+ erasing any changes you have made.
+
+
+
+
+ Close
+
+
+ This closes the dialog. Any unsaved changes will be
+ lost.
+
+
+
+
The rest of the dialog contains the parameters to be configured.