doc: Switch to asciidoctor to format docs

[fw/altos] / doc / telemini.inc

diff --git a/doc/telemini.inc b/doc/telemini.inc
index b40582a2093638c72321bd5cb84cf9b253f33eb9..b7b26a8a261999726fa8c976bd9f4a1b05fc2a87 100644 (file)
--- a/doc/telemini.inc
+++ b/doc/telemini.inc
@@ -1,8 +1,8 @@
 == TeleMini
 
        .TeleMini v3 Board
-       image::telemini-v3.0-top.jpg[width="5.5in"]
-       image::telemini-v3.0-bottom.jpg[width="5.5in"]
+       image::telemini-v3.0-top.jpg[width=400]
+       image::telemini-v3.0-bottom.jpg[width=400]
 
        TeleMini v3 is 0.5 inches by 1.67 inches.  It was
        designed to fit inside an 18mm air-frame tube, but using it in
@@ -94,6 +94,56 @@
                the left power switch wire. Hook a lead to either of the
                mounting holes for a ground connection.
 
+       === Using Packet Link Mode with TeleMini
+
+               After TeleMini powers up, it will check to see if some
+               device is attempting to communicate with it using
+               Packet Link Mode. If so, it will switch to idle mode
+               and start communicating. To switch to flight mode,
+               reboot the device either over the radio link or by
+               powering it off and back on.
+
+               If no ground station is attempting to communicate
+               using Packet Link Mode, TeleMini will enter pad mode
+               and prepare for flight.
+
+               The sequence of operations to use Packet Link Mode
+               with TeleMini is:
+
+               1. Configure the ground station data rate, frequency
+               and callsign to match the TeleMini settings.
+
+               2. Start Packet Link Mode in the ground station by
+               selecting the desired operation (Safe Flight Data,
+               Configure Altimeter, Fire Igniter or Monitor
+               Idle). Select the TeleBT or TeleDongle device. The
+               red LED should begin flashing rapidly.
+
+               3. Turn on TeleMini. You should see the red LED flash
+               very rapidly during the initial communication burst,
+               but it should then slow down when the link is idle.
+
+               Once TeleMini is in Idle mode, it will stay in that
+               mode until rebooted. That means you can stop one
+               Packet Link operation, wait a while and start another
+               Packet Link operation.
+
+       === Forcing TeleMini radio parameters to known defaults
+
+               If you don't know what the TeleMini frequency and
+               callsign settings are, you can temporarily force it
+               back to the original default values (frequency
+               434.550MHz, callsign N0CALL) by connecting a wire
+               between hole 3 and hole 7 on the debug connector. Hole
+               3 has the square pad around it, hole 7 is the one
+               nearest the MS5607 baro sensor, which is a rectangular
+               component with a metal cap that has two holes in it.
+
+               Once TeleMini has been powered up with this wire
+               connected, the wire may be removed. The radio
+               parameters will stay set to these default values until
+               changed by the user or when the device is rebooted.
+
        === TeleMini v1
 
                TeleMini v1 is the earlier version of this product. It
@@ -102,5 +152,5 @@
                power switch.
 
                .TeleMini v1 Board
-               image::telemini-v1-top.jpg[width="5.5in"]
+               image::telemini-v1-top.jpg[width=400]