altimeter and TeleDongle must be configured to the same
frequency to successfully communicate with each other.
</para>
- <para>
- To set the radio frequency, use the 'c R' command to specify the
- radio transceiver configuration parameter. This parameter is computed
- using the desired frequency, 'F', the radio calibration parameter, 'C' (showed by the 'c s' command) and
- the standard calibration reference frequency, 'S', (normally 434.550MHz):
- <programlisting>
- R = F / S * C
- </programlisting>
- Round the result to the nearest integer value.
- As with all 'c' sub-commands, follow this with a 'c w' to write the
- change to the parameter block in the on-board flash on
- your altimeter board if you want the change to stay in place across reboots.
- </para>
</section>
<section>
<title>Apogee Delay</title>
primary and backup pyrotechnic charges do not fire simultaneously.
</para>
<para>
- To set the apogee delay, use the 'c d' command.
- As with all 'c' sub-commands, follow this with a 'c w' to write the
- change to the parameter block in the on-board DataFlash chip.
- </para>
- <para>
- Please note that the Altus Metrum apogee detection algorithm
- fires exactly at apogee. If you are also flying an
- altimeter like the PerfectFlite MAWD, which only supports
- selecting 0 or 1 seconds of apogee delay, you may wish to
- set the MAWD to 0 seconds delay and set the TeleMetrum to
- fire your backup 2 or 3 seconds later to avoid any chance of
- both charges firing simultaneously. We've flown several
- air-frames this way quite happily, including Keith's
- successful L3 cert.
+ The Altus Metrum apogee detection algorithm fires exactly at
+ apogee. If you are also flying an altimeter like the
+ PerfectFlite MAWD, which only supports selecting 0 or 1
+ seconds of apogee delay, you may wish to set the MAWD to 0
+ seconds delay and set the TeleMetrum to fire your backup 2
+ or 3 seconds later to avoid any chance of both charges
+ firing simultaneously. We've flown several air-frames this
+ way quite happily, including Keith's successful L3 cert.
</para>
</section>
<section>
than the primary so that both pyrotechnic charges don't fire
simultaneously.
</para>
- <para>
- To set the main deployment altitude, use the 'c m' command.
- As with all 'c' sub-commands, follow this with a 'c w' to write the
- change to the parameter block in the on-board DataFlash chip.
- </para>
</section>
</section>
<section>
temperature changes is small enough that re-calibration by customers
should generally not be required.
</para>
- <para>
- To calibrate the radio frequency, connect the UHF antenna port to a
- frequency counter, set the board to 434.550MHz, and use the 'C'
- command to generate a CW carrier. Wait for the transmitter temperature
- to stabilize and the frequency to settle down.
- Then, divide 434.550 MHz by the
- measured frequency and multiply by the current radio cal value show
- in the 'c s' command. For an unprogrammed board, the default value
- is 1186611. Take the resulting integer and program it using the 'c f'
- command. Testing with the 'C' command again should show a carrier
- within a few tens of Hertz of the intended frequency.
- As with all 'c' sub-commands, follow this with a 'c w' to write the
- change to the parameter block in the on-board DataFlash chip.
- </para>
<para>
- when the radio calibration value is changed, the radio
+ When the radio calibration value is changed, the radio
frequency value is reset to the same value, so you'll need
to recompute and reset the radio frequency value using the
new radio calibration value.
</para>
</section>
</section>
- <section>
- <title>Updating Device Firmware</title>
- <para>
- The big conceptual thing to realize is that you have to use a
- TeleDongle as a programmer to update a TeleMetrum or TeleMini,
- and a TeleMetrum or other TeleDongle to program the TeleDongle
- Due to limited memory resources in the cc1111, we don't support
- programming directly over USB.
- </para>
- <para>
- You may wish to begin by ensuring you have current firmware images.
- These are distributed as part of the AltOS software bundle that
- also includes the AltosUI ground station program. Newer ground
- station versions typically work fine with older firmware versions,
- so you don't need to update your devices just to try out new
- software features. You can always download the most recent
- version from <ulink url="http://www.altusmetrum.org/AltOS/"/>.
- </para>
- <para>
- We recommend updating the altimeter first, before updating TeleDongle.
- </para>
- <section>
- <title>Updating TeleMetrum Firmware</title>
- <orderedlist inheritnum='inherit' numeration='arabic'>
- <listitem>
- Find the 'programming cable' that you got as part of the starter
- kit, that has a red 8-pin MicroMaTch connector on one end and a
- red 4-pin MicroMaTch connector on the other end.
- </listitem>
- <listitem>
- Take the 2 screws out of the TeleDongle case to get access
- to the circuit board.
- </listitem>
- <listitem>
- Plug the 8-pin end of the programming cable to the
- matching connector on the TeleDongle, and the 4-pin end to the
- matching connector on the TeleMetrum.
- Note that each MicroMaTch connector has an alignment pin that
- goes through a hole in the PC board when you have the cable
- oriented correctly.
- </listitem>
- <listitem>
- Attach a battery to the TeleMetrum board.
- </listitem>
- <listitem>
- Plug the TeleDongle into your computer's USB port, and power
- up the TeleMetrum.
- </listitem>
- <listitem>
- Run AltosUI, and select 'Flash Image' from the File menu.
- </listitem>
- <listitem>
- Pick the TeleDongle device from the list, identifying it as the
- programming device.
- </listitem>
- <listitem>
- Select the image you want put on the TeleMetrum, which should have a
- name in the form telemetrum-v1.1-1.0.0.ihx. It should be visible
- in the default directory, if not you may have to poke around
- your system to find it.
- </listitem>
- <listitem>
- Make sure the configuration parameters are reasonable
- looking. If the serial number and/or RF configuration
- values aren't right, you'll need to change them.
- </listitem>
- <listitem>
- Hit the 'OK' button and the software should proceed to flash
- the TeleMetrum with new firmware, showing a progress bar.
- </listitem>
- <listitem>
- Confirm that the TeleMetrum board seems to have updated OK, which you
- can do by plugging in to it over USB and using a terminal program
- to connect to the board and issue the 'v' command to check
- the version, etc.
- </listitem>
- <listitem>
- If something goes wrong, give it another try.
- </listitem>
- </orderedlist>
- </section>
- <section>
- <title>Updating TeleMini Firmware</title>
- <orderedlist inheritnum='inherit' numeration='arabic'>
- <listitem>
- You'll need a special 'programming cable' to reprogram the
- TeleMini. It's available on the Altus Metrum web store, or
- you can make your own using an 8-pin MicroMaTch connector on
- one end and a set of four pins on the other.
- </listitem>
- <listitem>
- Take the 2 screws out of the TeleDongle case to get access
- to the circuit board.
- </listitem>
- <listitem>
- Plug the 8-pin end of the programming cable to the matching
- connector on the TeleDongle, and the 4-pins into the holes
- in the TeleMini circuit board. Note that the MicroMaTch
- connector has an alignment pin that goes through a hole in
- the PC board when you have the cable oriented correctly, and
- that pin 1 on the TeleMini board is marked with a square pad
- while the other pins have round pads.
- </listitem>
- <listitem>
- Attach a battery to the TeleMini board.
- </listitem>
- <listitem>
- Plug the TeleDongle into your computer's USB port, and power
- up the TeleMini
- </listitem>
- <listitem>
- Run AltosUI, and select 'Flash Image' from the File menu.
- </listitem>
- <listitem>
- Pick the TeleDongle device from the list, identifying it as the
- programming device.
- </listitem>
- <listitem>
- Select the image you want put on the TeleMini, which should have a
- name in the form telemini-v1.0-1.0.0.ihx. It should be visible
- in the default directory, if not you may have to poke around
- your system to find it.
- </listitem>
- <listitem>
- Make sure the configuration parameters are reasonable
- looking. If the serial number and/or RF configuration
- values aren't right, you'll need to change them.
- </listitem>
- <listitem>
- Hit the 'OK' button and the software should proceed to flash
- the TeleMini with new firmware, showing a progress bar.
- </listitem>
- <listitem>
- Confirm that the TeleMini board seems to have updated OK, which you
- can do by configuring it over the radio link through the TeleDongle, or
- letting it come up in "flight" mode and listening for telemetry.
- </listitem>
- <listitem>
- If something goes wrong, give it another try.
- </listitem>
- </orderedlist>
- </section>
- <section>
- <title>Updating TeleDongle Firmware</title>
- <para>
- Updating TeleDongle's firmware is just like updating TeleMetrum or TeleMini
- firmware, but you use either a TeleMetrum or another TeleDongle as the programmer.
- </para>
- <orderedlist inheritnum='inherit' numeration='arabic'>
- <listitem>
- Find the 'programming cable' that you got as part of the starter
- kit, that has a red 8-pin MicroMaTch connector on one end and a
- red 4-pin MicroMaTch connector on the other end.
- </listitem>
- <listitem>
- Find the USB cable that you got as part of the starter kit, and
- plug the "mini" end in to the mating connector on TeleMetrum or TeleDongle.
- </listitem>
- <listitem>
- Take the 2 screws out of the TeleDongle case to get access
- to the circuit board.
- </listitem>
- <listitem>
- Plug the 8-pin end of the programming cable to the
- matching connector on the programmer, and the 4-pin end to the
- matching connector on the TeleDongle.
- Note that each MicroMaTch connector has an alignment pin that
- goes through a hole in the PC board when you have the cable
- oriented correctly.
- </listitem>
- <listitem>
- Attach a battery to the TeleMetrum board if you're using one.
- </listitem>
- <listitem>
- Plug both the programmer and the TeleDongle into your computer's USB
- ports, and power up the programmer.
- </listitem>
- <listitem>
- Run AltosUI, and select 'Flash Image' from the File menu.
- </listitem>
- <listitem>
- Pick the programmer device from the list, identifying it as the
- programming device.
- </listitem>
- <listitem>
- Select the image you want put on the TeleDongle, which should have a
- name in the form teledongle-v0.2-1.0.0.ihx. It should be visible
- in the default directory, if not you may have to poke around
- your system to find it.
- </listitem>
- <listitem>
- Make sure the configuration parameters are reasonable
- looking. If the serial number and/or RF configuration
- values aren't right, you'll need to change them. The TeleDongle
- serial number is on the "bottom" of the circuit board, and can
- usually be read through the translucent blue plastic case without
- needing to remove the board from the case.
- </listitem>
- <listitem>
- Hit the 'OK' button and the software should proceed to flash
- the TeleDongle with new firmware, showing a progress bar.
- </listitem>
- <listitem>
- Confirm that the TeleDongle board seems to have updated OK, which you
- can do by plugging in to it over USB and using a terminal program
- to connect to the board and issue the 'v' command to check
- the version, etc. Once you're happy, remove the programming cable
- and put the cover back on the TeleDongle.
- </listitem>
- <listitem>
- If something goes wrong, give it another try.
- </listitem>
- </orderedlist>
- <para>
- Be careful removing the programming cable from the locking 8-pin
- connector on TeleMetrum. You'll need a fingernail or perhaps a thin
- screwdriver or knife blade to gently pry the locking ears out
- slightly to extract the connector. We used a locking connector on
- TeleMetrum to help ensure that the cabling to companion boards
- used in a rocket don't ever come loose accidentally in flight.
- </para>
- </section>
- </section>
</chapter>
<chapter>
This reprograms any Altus Metrum device by using a TeleMetrum
or TeleDongle as a programming dongle. Please read the
directions for flashing devices in the Updating Device
- Firmware section above
+ Firmware chapter below.
</para>
<para>
Once you have the programmer and target devices connected,
</itemizedlist>
</section>
<section>
- <title>The Barometric Sensor</title>
- <para>
- Altusmetrum altimeters measure altitude with a barometric
- sensor, essentially measuring the amount of air above the
- rocket to figure out how high it is. A large number of
- measurements are taken as the altimeter initializes itself to
- figure out the pad altitude. Subsequent measurements are then
- used to compute the height above the pad.
- </para>
- <para>
- To accurately measure atmospheric pressure, the ebay
- containing the altimeter must be vented outside the
- air-frame. The vent must be placed in a region of linear
- airflow, smooth and not in an area of increasing or decreasing
- pressure.
- </para>
- <para>
- The barometric sensor in the altimeter is quite sensitive to
- chemical damage from the products of APCP or BP combustion, so
- make sure the ebay is carefully sealed from any compartment
- which contains ejection charges or motors.
- </para>
+ <title>The Barometric Sensor</title>
+ <para>
+ Altusmetrum altimeters measure altitude with a barometric
+ sensor, essentially measuring the amount of air above the
+ rocket to figure out how high it is. A large number of
+ measurements are taken as the altimeter initializes itself to
+ figure out the pad altitude. Subsequent measurements are then
+ used to compute the height above the pad.
+ </para>
+ <para>
+ To accurately measure atmospheric pressure, the ebay
+ containing the altimeter must be vented outside the
+ air-frame. The vent must be placed in a region of linear
+ airflow, smooth and not in an area of increasing or decreasing
+ pressure.
+ </para>
+ <para>
+ The barometric sensor in the altimeter is quite sensitive to
+ chemical damage from the products of APCP or BP combustion, so
+ make sure the ebay is carefully sealed from any compartment
+ which contains ejection charges or motors.
+ </para>
+ </section>
+ <section>
+ <title>Ground Testing</title>
+ <para>
+ The most important aspect of any installation is careful
+ ground testing. Bringing an air-frame up to the LCO table which
+ hasn't been ground tested can lead to delays or ejection
+ charges firing on the pad, or, even worse, a recovery system
+ failure.
+ </para>
+ <para>
+ Do a 'full systems' test that includes wiring up all igniters
+ without any BP and turning on all of the electronics in flight
+ mode. This will catch any mistakes in wiring and any residual
+ RFI issues that might accidentally fire igniters at the wrong
+ time. Let the air-frame sit for several minutes, checking for
+ adequate telemetry signal strength and GPS lock.
+ </para>
+ <para>
+ Ground test the ejection charges. Prepare the rocket for
+ flight, loading ejection charges and igniters. Completely
+ assemble the air-frame and then use the 'Fire Igniters'
+ interface through a TeleDongle to command each charge to
+ fire. Make sure the charge is sufficient to robustly separate
+ the air-frame and deploy the recovery system.
+ </para>
+ </section>
+ </chapter>
+ <chapter>
+ <title>Updating Device Firmware</title>
+ <para>
+ The big conceptual thing to realize is that you have to use a
+ TeleDongle as a programmer to update a TeleMetrum or TeleMini,
+ and a TeleMetrum or other TeleDongle to program the TeleDongle
+ Due to limited memory resources in the cc1111, we don't support
+ programming directly over USB.
+ </para>
+ <para>
+ You may wish to begin by ensuring you have current firmware images.
+ These are distributed as part of the AltOS software bundle that
+ also includes the AltosUI ground station program. Newer ground
+ station versions typically work fine with older firmware versions,
+ so you don't need to update your devices just to try out new
+ software features. You can always download the most recent
+ version from <ulink url="http://www.altusmetrum.org/AltOS/"/>.
+ </para>
+ <para>
+ We recommend updating the altimeter first, before updating TeleDongle.
+ </para>
+ <section>
+ <title>Updating TeleMetrum Firmware</title>
+ <orderedlist inheritnum='inherit' numeration='arabic'>
+ <listitem>
+ Find the 'programming cable' that you got as part of the starter
+ kit, that has a red 8-pin MicroMaTch connector on one end and a
+ red 4-pin MicroMaTch connector on the other end.
+ </listitem>
+ <listitem>
+ Take the 2 screws out of the TeleDongle case to get access
+ to the circuit board.
+ </listitem>
+ <listitem>
+ Plug the 8-pin end of the programming cable to the
+ matching connector on the TeleDongle, and the 4-pin end to the
+ matching connector on the TeleMetrum.
+ Note that each MicroMaTch connector has an alignment pin that
+ goes through a hole in the PC board when you have the cable
+ oriented correctly.
+ </listitem>
+ <listitem>
+ Attach a battery to the TeleMetrum board.
+ </listitem>
+ <listitem>
+ Plug the TeleDongle into your computer's USB port, and power
+ up the TeleMetrum.
+ </listitem>
+ <listitem>
+ Run AltosUI, and select 'Flash Image' from the File menu.
+ </listitem>
+ <listitem>
+ Pick the TeleDongle device from the list, identifying it as the
+ programming device.
+ </listitem>
+ <listitem>
+ Select the image you want put on the TeleMetrum, which should have a
+ name in the form telemetrum-v1.1-1.0.0.ihx. It should be visible
+ in the default directory, if not you may have to poke around
+ your system to find it.
+ </listitem>
+ <listitem>
+ Make sure the configuration parameters are reasonable
+ looking. If the serial number and/or RF configuration
+ values aren't right, you'll need to change them.
+ </listitem>
+ <listitem>
+ Hit the 'OK' button and the software should proceed to flash
+ the TeleMetrum with new firmware, showing a progress bar.
+ </listitem>
+ <listitem>
+ Confirm that the TeleMetrum board seems to have updated OK, which you
+ can do by plugging in to it over USB and using a terminal program
+ to connect to the board and issue the 'v' command to check
+ the version, etc.
+ </listitem>
+ <listitem>
+ If something goes wrong, give it another try.
+ </listitem>
+ </orderedlist>
+ </section>
+ <section>
+ <title>Updating TeleMini Firmware</title>
+ <orderedlist inheritnum='inherit' numeration='arabic'>
+ <listitem>
+ You'll need a special 'programming cable' to reprogram the
+ TeleMini. It's available on the Altus Metrum web store, or
+ you can make your own using an 8-pin MicroMaTch connector on
+ one end and a set of four pins on the other.
+ </listitem>
+ <listitem>
+ Take the 2 screws out of the TeleDongle case to get access
+ to the circuit board.
+ </listitem>
+ <listitem>
+ Plug the 8-pin end of the programming cable to the matching
+ connector on the TeleDongle, and the 4-pins into the holes
+ in the TeleMini circuit board. Note that the MicroMaTch
+ connector has an alignment pin that goes through a hole in
+ the PC board when you have the cable oriented correctly, and
+ that pin 1 on the TeleMini board is marked with a square pad
+ while the other pins have round pads.
+ </listitem>
+ <listitem>
+ Attach a battery to the TeleMini board.
+ </listitem>
+ <listitem>
+ Plug the TeleDongle into your computer's USB port, and power
+ up the TeleMini
+ </listitem>
+ <listitem>
+ Run AltosUI, and select 'Flash Image' from the File menu.
+ </listitem>
+ <listitem>
+ Pick the TeleDongle device from the list, identifying it as the
+ programming device.
+ </listitem>
+ <listitem>
+ Select the image you want put on the TeleMini, which should have a
+ name in the form telemini-v1.0-1.0.0.ihx. It should be visible
+ in the default directory, if not you may have to poke around
+ your system to find it.
+ </listitem>
+ <listitem>
+ Make sure the configuration parameters are reasonable
+ looking. If the serial number and/or RF configuration
+ values aren't right, you'll need to change them.
+ </listitem>
+ <listitem>
+ Hit the 'OK' button and the software should proceed to flash
+ the TeleMini with new firmware, showing a progress bar.
+ </listitem>
+ <listitem>
+ Confirm that the TeleMini board seems to have updated OK, which you
+ can do by configuring it over the radio link through the TeleDongle, or
+ letting it come up in "flight" mode and listening for telemetry.
+ </listitem>
+ <listitem>
+ If something goes wrong, give it another try.
+ </listitem>
+ </orderedlist>
</section>
<section>
- <title>Ground Testing</title>
- <para>
- The most important aspect of any installation is careful
- ground testing. Bringing an air-frame up to the LCO table which
- hasn't been ground tested can lead to delays or ejection
- charges firing on the pad, or, even worse, a recovery system
- failure.
- </para>
+ <title>Updating TeleDongle Firmware</title>
<para>
- Do a 'full systems' test that includes wiring up all igniters
- without any BP and turning on all of the electronics in flight
- mode. This will catch any mistakes in wiring and any residual
- RFI issues that might accidentally fire igniters at the wrong
- time. Let the air-frame sit for several minutes, checking for
- adequate telemetry signal strength and GPS lock.
- </para>
+ Updating TeleDongle's firmware is just like updating TeleMetrum or TeleMini
+ firmware, but you use either a TeleMetrum or another TeleDongle as the programmer.
+ </para>
+ <orderedlist inheritnum='inherit' numeration='arabic'>
+ <listitem>
+ Find the 'programming cable' that you got as part of the starter
+ kit, that has a red 8-pin MicroMaTch connector on one end and a
+ red 4-pin MicroMaTch connector on the other end.
+ </listitem>
+ <listitem>
+ Find the USB cable that you got as part of the starter kit, and
+ plug the "mini" end in to the mating connector on TeleMetrum or TeleDongle.
+ </listitem>
+ <listitem>
+ Take the 2 screws out of the TeleDongle case to get access
+ to the circuit board.
+ </listitem>
+ <listitem>
+ Plug the 8-pin end of the programming cable to the
+ matching connector on the programmer, and the 4-pin end to the
+ matching connector on the TeleDongle.
+ Note that each MicroMaTch connector has an alignment pin that
+ goes through a hole in the PC board when you have the cable
+ oriented correctly.
+ </listitem>
+ <listitem>
+ Attach a battery to the TeleMetrum board if you're using one.
+ </listitem>
+ <listitem>
+ Plug both the programmer and the TeleDongle into your computer's USB
+ ports, and power up the programmer.
+ </listitem>
+ <listitem>
+ Run AltosUI, and select 'Flash Image' from the File menu.
+ </listitem>
+ <listitem>
+ Pick the programmer device from the list, identifying it as the
+ programming device.
+ </listitem>
+ <listitem>
+ Select the image you want put on the TeleDongle, which should have a
+ name in the form teledongle-v0.2-1.0.0.ihx. It should be visible
+ in the default directory, if not you may have to poke around
+ your system to find it.
+ </listitem>
+ <listitem>
+ Make sure the configuration parameters are reasonable
+ looking. If the serial number and/or RF configuration
+ values aren't right, you'll need to change them. The TeleDongle
+ serial number is on the "bottom" of the circuit board, and can
+ usually be read through the translucent blue plastic case without
+ needing to remove the board from the case.
+ </listitem>
+ <listitem>
+ Hit the 'OK' button and the software should proceed to flash
+ the TeleDongle with new firmware, showing a progress bar.
+ </listitem>
+ <listitem>
+ Confirm that the TeleDongle board seems to have updated OK, which you
+ can do by plugging in to it over USB and using a terminal program
+ to connect to the board and issue the 'v' command to check
+ the version, etc. Once you're happy, remove the programming cable
+ and put the cover back on the TeleDongle.
+ </listitem>
+ <listitem>
+ If something goes wrong, give it another try.
+ </listitem>
+ </orderedlist>
<para>
- Ground test the ejection charges. Prepare the rocket for
- flight, loading ejection charges and igniters. Completely
- assemble the air-frame and then use the 'Fire Igniters'
- interface through a TeleDongle to command each charge to
- fire. Make sure the charge is sufficient to robustly separate
- the air-frame and deploy the recovery system.
+ Be careful removing the programming cable from the locking 8-pin
+ connector on TeleMetrum. You'll need a fingernail or perhaps a thin
+ screwdriver or knife blade to gently pry the locking ears out
+ slightly to extract the connector. We used a locking connector on
+ TeleMetrum to help ensure that the cabling to companion boards
+ used in a rocket don't ever come loose accidentally in flight.
</para>
</section>
</chapter>
Verify you can connect and disconnect from the units while in your
terminal program by sending the escape-disconnect mentioned above.
</para>
+ <para>
+ To set the radio frequency, use the 'c R' command to specify the
+ radio transceiver configuration parameter. This parameter is computed
+ using the desired frequency, 'F', the radio calibration parameter, 'C' (showed by the 'c s' command) and
+ the standard calibration reference frequency, 'S', (normally 434.550MHz):
+ <programlisting>
+ R = F / S * C
+ </programlisting>
+ Round the result to the nearest integer value.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board flash on
+ your altimeter board if you want the change to stay in place across reboots.
+ </para>
+ <para>
+ To set the apogee delay, use the 'c d' command.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board DataFlash chip.
+ </para>
+ <para>
+ To set the main deployment altitude, use the 'c m' command.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board DataFlash chip.
+ </para>
+ <para>
+ To calibrate the radio frequency, connect the UHF antenna port to a
+ frequency counter, set the board to 434.550MHz, and use the 'C'
+ command to generate a CW carrier. Wait for the transmitter temperature
+ to stabilize and the frequency to settle down.
+ Then, divide 434.550 MHz by the
+ measured frequency and multiply by the current radio cal value show
+ in the 'c s' command. For an unprogrammed board, the default value
+ is 1186611. Take the resulting integer and program it using the 'c f'
+ command. Testing with the 'C' command again should show a carrier
+ within a few tens of Hertz of the intended frequency.
+ As with all 'c' sub-commands, follow this with a 'c w' to write the
+ change to the parameter block in the on-board DataFlash chip.
+ </para>
<para>
Note that the 'reboot' command, which is very useful on the altimeters,
will likely just cause problems with the dongle. The *correct* way
strength providing an indication of the direction from receiver to rocket.
</para>
<para>
- TeleMetrum also provides GPS trekking data, which can further simplify
+ TeleMetrum also provides GPS tracking data, which can further simplify
locating the rocket once it has landed. (The last good GPS data
received before touch-down will be on the data screen of 'ao-view'.)
</para>
projects / fw / altos / blobdiff