#!/usr/bin/nickle -f
/*
 * Pressure Sensor Model, version 1.1
 *
 * written by Holly Grimes
 *
 * Uses the International Standard Atmosphere as described in
 *   "A Quick Derivation relating altitude to air pressure" (version 1.03)
 *    from the Portland State Aerospace Society, except that the atmosphere
 *    is divided into layers with each layer having a different lapse rate.
 *
 * Lapse rate data for each layer was obtained from Wikipedia on Sept. 1, 2007
 *    at site <http://en.wikipedia.org/wiki/International_Standard_Atmosphere
 *
 * Height measurements use the local tangent plane.  The postive z-direction is up.
 *
 * All measurements are given in SI units (Kelvin, Pascal, meter, meters/second^2).
 *   The lapse rate is given in Kelvin/meter, the gas constant for air is given
 *   in Joules/(kilogram-Kelvin).
 */

const real GRAVITATIONAL_ACCELERATION = -9.80665;
const real AIR_GAS_CONSTANT = 287.053;
const int NUMBER_OF_LAYERS = 7;
const real MAXIMUM_ALTITUDE = 84852;
const real MINIMUM_PRESSURE = 0.3734;
const real LAYER0_BASE_TEMPERATURE = 288.15;
const real LAYER0_BASE_PRESSURE = 101325;

/* lapse rate and base altitude for each layer in the atmosphere */
const real[NUMBER_OF_LAYERS] lapse_rate = {
	-0.0065, 0.0, 0.001, 0.0028, 0.0, -0.0028, -0.002
};
const int[NUMBER_OF_LAYERS] base_altitude = {
	0, 11000, 20000, 32000, 47000, 51000, 71000
};


/* outputs atmospheric pressure associated with the given altitude. altitudes
   are measured with respect to the mean sea level */
real altitude_to_pressure(real altitude) {

   real base_temperature = LAYER0_BASE_TEMPERATURE;
   real base_pressure = LAYER0_BASE_PRESSURE;

   real pressure;
   real base; /* base for function to determine pressure */
   real exponent; /* exponent for function to determine pressure */
   int layer_number; /* identifies layer in the atmosphere */
   int delta_z; /* difference between two altitudes */

   if (altitude > MAXIMUM_ALTITUDE) /* FIX ME: use sensor data to improve model */
      return 0;

   /* calculate the base temperature and pressure for the atmospheric layer
      associated with the inputted altitude */
   for(layer_number = 0; layer_number < NUMBER_OF_LAYERS - 1 && altitude > base_altitude[layer_number + 1]; layer_number++) {
      delta_z = base_altitude[layer_number + 1] - base_altitude[layer_number];
      if (lapse_rate[layer_number] == 0.0) {
         exponent = GRAVITATIONAL_ACCELERATION * delta_z
              / AIR_GAS_CONSTANT / base_temperature;
         base_pressure *= exp(exponent);
      }
      else {
         base = (lapse_rate[layer_number] * delta_z / base_temperature) + 1.0;
         exponent = GRAVITATIONAL_ACCELERATION /
              (AIR_GAS_CONSTANT * lapse_rate[layer_number]);
         base_pressure *= pow(base, exponent);
      }
      base_temperature += delta_z * lapse_rate[layer_number];
   }

   /* calculate the pressure at the inputted altitude */
   delta_z = altitude - base_altitude[layer_number];
   if (lapse_rate[layer_number] == 0.0) {
      exponent = GRAVITATIONAL_ACCELERATION * delta_z
           / AIR_GAS_CONSTANT / base_temperature;
      pressure = base_pressure * exp(exponent);
   }
   else {
      base = (lapse_rate[layer_number] * delta_z / base_temperature) + 1.0;
      exponent = GRAVITATIONAL_ACCELERATION /
           (AIR_GAS_CONSTANT * lapse_rate[layer_number]);
      pressure = base_pressure * pow(base, exponent);
   }

   return pressure;
}


/* outputs the altitude associated with the given pressure. the altitude
   returned is measured with respect to the mean sea level */
real pressure_to_altitude(real pressure) {

   real next_base_temperature = LAYER0_BASE_TEMPERATURE;
   real next_base_pressure = LAYER0_BASE_PRESSURE;

   real altitude;
   real base_pressure;
   real base_temperature;
   real base; /* base for function to determine base pressure of next layer */
   real exponent; /* exponent for function to determine base pressure
                             of next layer */
   real coefficient;
   int layer_number; /* identifies layer in the atmosphere */
   int delta_z; /* difference between two altitudes */

   if (pressure < 0)  /* illegal pressure */
      return -1;
   if (pressure < MINIMUM_PRESSURE) /* FIX ME: use sensor data to improve model */
      return MAXIMUM_ALTITUDE;

   /* calculate the base temperature and pressure for the atmospheric layer
      associated with the inputted pressure. */
   layer_number = -1;
   do {
      layer_number++;
      base_pressure = next_base_pressure;
      base_temperature = next_base_temperature;
      delta_z = base_altitude[layer_number + 1] - base_altitude[layer_number];
      if (lapse_rate[layer_number] == 0.0) {
         exponent = GRAVITATIONAL_ACCELERATION * delta_z
              / AIR_GAS_CONSTANT / base_temperature;
         next_base_pressure *= exp(exponent);
      }
      else {
         base = (lapse_rate[layer_number] * delta_z / base_temperature) + 1.0;
         exponent = GRAVITATIONAL_ACCELERATION /
              (AIR_GAS_CONSTANT * lapse_rate[layer_number]);
         next_base_pressure *= pow(base, exponent);
      }
      next_base_temperature += delta_z * lapse_rate[layer_number];
   }
   while(layer_number < NUMBER_OF_LAYERS - 1 && pressure < next_base_pressure);

   /* calculate the altitude associated with the inputted pressure */
   if (lapse_rate[layer_number] == 0.0) {
      coefficient = (AIR_GAS_CONSTANT / GRAVITATIONAL_ACCELERATION)
                                                    * base_temperature;
      altitude = base_altitude[layer_number]
                    + coefficient * log(pressure / base_pressure);
   }
   else {
      base = pressure / base_pressure;
      exponent = AIR_GAS_CONSTANT * lapse_rate[layer_number]
                                       / GRAVITATIONAL_ACCELERATION;
      coefficient = base_temperature / lapse_rate[layer_number];
      altitude = base_altitude[layer_number]
                      + coefficient * (pow(base, exponent) - 1);
   }

   return altitude;
}

real feet_to_meters(real feet)
{
    return feet * (12 * 2.54 / 100);
}

real meters_to_feet(real meters)
{
    return meters / (12 * 2.54 / 100);
}

/*
 * Values for our MS5607
 *
 * From the data sheet:
 *
 * Pressure range: 10-1200 mbar (1000 - 120000 Pa)
 *
 * Pressure data is reported in units of Pa
 */

typedef struct {
	real m, b;
	int m_i, b_i;
} line_t;

line_t best_fit(real[] values, int first, int last) {
       real sum_x = 0, sum_x2 = 0, sum_y = 0, sum_xy = 0;
       int n = last - first + 1;
       real m, b;
       int m_i, b_i;

       for (int i = first; i <= last; i++) {
	       sum_x += i;
	       sum_x2 += i**2;
	       sum_y += values[i];
	       sum_xy += values[i] * i;
       }
       m = (n*sum_xy - sum_y*sum_x) / (n*sum_x2 - sum_x**2);
       b = sum_y/n - m*(sum_x/n);
       return (line_t) { m = m, b = b };
}

real	min_Pa = 0;
real	max_Pa = 120000;

/* Target is an array of < 2000 entries */
int pa_sample_shift = 3;
int pa_part_shift = 3;

int num_part = ceil(max_Pa / (2 ** (pa_part_shift + pa_sample_shift)));

int num_samples = num_part << pa_part_shift;

real sample_to_Pa(int sample) = sample << pa_sample_shift;

real sample_to_altitude(int sample) = pressure_to_altitude(sample_to_Pa(sample));

int part_to_sample(int part) = part << pa_part_shift;

real[num_samples] alt = { [n] = sample_to_altitude(n) };

int seg_len = 1 << pa_part_shift;

line_t [num_part] fit = {
	[n] = best_fit(alt, n * seg_len, n * seg_len + seg_len - 1)
};

int[num_samples/seg_len + 1]	alt_part;

alt_part[0] = floor (fit[0].b + 0.5);
alt_part[dim(fit)] = floor(fit[dim(fit)-1].m * dim(fit) * seg_len + fit[dim(fit)-1].b + 0.5);

for (int i = 0; i < dim(fit) - 1; i++) {
	real	here, there;
	here = fit[i].m * (i+1) * seg_len + fit[i].b;
	there = fit[i+1].m * (i+1) * seg_len + fit[i+1].b;
	alt_part[i+1] = floor ((here + there) / 2 + 0.5);
}

real sample_to_fit_altitude(int sample) {
	int	sub = sample // seg_len;
	int	off = sample % seg_len;
	line_t	l = fit[sub];
	real r_v;
	real i_v;

	r_v = sample * l.m + l.b;
	i_v = (alt_part[sub] * (seg_len - off) + alt_part[sub+1] * off) / seg_len;
	return i_v;
}

real max_error = 0;
int max_error_sample = 0;
real total_error = 0;

for (int sample = 0; sample < num_samples; sample++) {
	real	Pa = sample_to_Pa(sample);
	real	meters = pressure_to_altitude(Pa);

	real	meters_approx = sample_to_fit_altitude(sample);
	real	error = abs(meters - meters_approx);

	total_error += error;
	if (error > max_error) {
		max_error = error;
		max_error_sample = sample;
	}
#	printf ("	%7d,	/* %6.2f kPa %5d sample approx %d */\n",
#		floor (meters + 0.5), Pa / 1000, sample, floor(sample_to_fit_altitude(sample) + 0.5));
}

printf ("/*max error %f at %7.3f%%. Average error %f*/\n", max_error, max_error_sample / (num_samples - 1) * 100, total_error / num_samples);

printf ("#define NALT %d\n", dim(alt_part));
printf ("#define ALT_SHIFT %d\n", pa_part_shift + pa_sample_shift);

for (int part = 0; part < dim(alt_part); part++) {
	real kPa = sample_to_Pa(part_to_sample(part)) / 1000;
	printf ("%9d, /* %6.2f kPa */\n",
		alt_part[part], kPa);
}