altos: Remove cc1111 products We're not testing these anyways; building new firmware for them is not helpful. Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Make CDC ACM 'line coding' public This allows other systems to see what baud rate the host has requested. Signed-off-by: Keith Packard <keithp@keithp.com>
Switch from GPLv2 to GPLv2+ Signed-off-by: Keith Packard <keithp@keithp.com>
altos/cc1111: Add support for CPU-driven USB pullup Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Expose ao_usb_running globally This lets other bits of the code know when USB has been connected. Signed-off-by: Keith Packard <keithp@keithp.com>
Initial TeleMini bits Signed-off-by: Keith Packard <keithp@keithp.com>
altos/cc1111: Hack on USB driver to make Windows happy The Windows modem driver is quite chatty at startup time, getting and setting the comm parameters each time the device is opened. Sometimes, when setting the parameters, the cc1111 would STALL EP0. Most of the time, Windows would happily pass this as an error back to AltosUI which would then re-try the open (and succeed, most of the time). Sometimes, Windows would stall for 30 seconds before passing the error back. This made the whole UI freeze, and I suspect most people assumed our app had died. A bit of analysis with the beagle USB sniffer and I discovered the STALL settings, but there wasn't any correlation between the data on the wire and when the STALL would be generated. So, I found a couple of other cc1111 USB stacks on the net and just looked to see how our driver differed. There wasn't anything clearly related, but there were a list of small differences: 1) Other drivers didn't bother waiting for the hardware to ack the USBADDR setting; doing it this way means we can set the address *before* acking the setup packet. It'll get set eventually, at which point the device will start responding to packets again. Easy to fix, and saves a bit of code space too. 2) The other drivers set the STALL bit for setup packets which aren't understood. This shouldn't have any effect on 'good' systems as those shouldn't ever be generating bogus setup packets anyways. The driver already handled the STALL state in the interrupt handler, the only requirement was to figure out when to explicitly set the STALL bit. That required moving the state updating code from the start of the ep0 setup handling to the end, after the setup packet had been examined and data queued in or out as appropriate. 3) Our driver explicitly queued an IN packet for any setup request that wasn't waiting for an OUT pack. This appears to tie in with the USBADDR change above as before I made that change, this change caused the driver to fail to respond to most setup packets. This was simple once the above change was made, just move the generation of the IN packet inside the code that switched to the IN state. Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Do not release interrupts from any pollchar function getchar relies on interrupts being blocked across the pollchar calls and into the sleep call or it may go to sleep with data pending. This prefixes all pollchar functions with _ to indicate that they are to be called with interrupts blocked and eliminates all interrupt manipulation calls from within the pollchar functions. Signed-off-by: Keith Packard <keithp@keithp.com>
altos: fix functions calling pollchar to use 'int' to hold the value AO_READ_AGAIN doesn't fit in a char anymore now that stdio is 8-bit clean, everyone using pollchar must use an 'int' variable to capture the whole value from pollchar. Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Make stdio 8-bit clean by making pollchar return int We were stealing one value (0xff) in the return value from pollchar to indicate 'not ready yet'. Instead of doing that, use the integer value -1 and have pollchar return an int instead of a char. That necessitated cleaning a few other bits to make sure that 0xff wouldn't get promoted to -1 on accident. Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Massive product config cleanup Support multiple serial ports more cleanly Split out parts of ao.h into separate feature header files Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Add button driver and sample user Hook up the teleterra buttons and have them beep Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Restructure altos build to prepare for multi-arch support Split out sources into separate directories: core: architecture and product independent bits cc1111: cc1111-specific code drivers: architecture independent drivers product: product-specific sources and Makefile fragments util: scripts for building stuff This should have no effect on the built products, but testing is encouraged Signed-off-by: Keith Packard <keithp@keithp.com>