Imported Upstream version 2.5.2p1

[debian/amanda] / amplot / amplot.awk

diff --git a/amplot/amplot.awk b/amplot/amplot.awk
index 962c080b29d237b211ac71add22d25971e089568..fa34c4bdc4d4a0a2b0d54be5c9001ec3171beee5 100644 (file)
--- a/amplot/amplot.awk
+++ b/amplot/amplot.awk
@@ -92,7 +92,7 @@ BEGIN{
                else if( $2=="flush" && $3=="size" ) {
                        flush_size = $4;
                }
-               else if( $2=="start")       do_start();
+               else if( $2=="start" && $3=="time")       do_start();
                else if( $2=="send-cmd") { 
                        if( $7=="FILE-DUMP"){
                          file_dump++;
@@ -107,6 +107,9 @@ BEGIN{
                else if( $2=="finished-cmd") cmd_fin++;
                else if( $2=="started")      forked++;
                else if( $2=="QUITTING")     do_quit();
+               else if( $2=="find_diskspace:") ; #eat this line
+               else if( $2=="assign_holdingdisk:") ; #eat this line
+               else if( $2=="adjust_diskspace:") ; #eat this line
                else if( $2=="tape" && $3=="size") ; #eat this line
                else if( $2=="dump" && $3=="failed") ; #eat this line
                else if( $2=="taper" && $3=="failed") ; #eat this line
@@ -129,7 +132,7 @@ BEGIN{
                    print fil, "INFO#", $0;
        }
        else if( $1 == "taper:") {
-               if($3 != "label" && $3 != "end" && $2 != "DONE" && $2 != "pid" && $2 != "slot" && $2 != "reader-side:" && $2 != "page" && $2 != "buffer" && $3 != "at")
+               if($3 != "label" && $3 != "end" && $2 != "DONE" && $2 != "pid" && $2 != "slot" && $2 != "reader-side:" && $2 != "page" && $2 != "buffer" && $3 != "at" && $3 != "switching" && $2 != "slot:")
                    print fil, "INFO#", $0;
        }
        else if( $1 == "FLUSH") {
@@ -151,11 +154,16 @@ function do_state(){              # state line is printed out after driver
 # $11 = "writing"/"idle"# $12 = "idle-dumpers:"
 # $13 = #idle          # $14 = "qlen"          # $15 = "tapeq:"
 # $16 = #waiting       # $17 = "runq:"         # $18 = #not started 
-# $19 = "stoppedq:"    # $20 = #stopped
+# $19 = "roomq"                # $20 = #roomq          # $21 = "wakeup:"
+# $22 = #wakeup                # $23 = "driver-idle:"  # $23 = status
 
        cnt++;                                  # number of event
        time = $4/time_scale;
-       unused = (bandw - $7)*bandw_scale+bandw_raise;
+       #Check overflow in driver ouput (big value instead of negative)
+       if($7>0 && $7 < 0x7fffffff)
+               unused = (bandw - $7)*bandw_scale+bandw_raise;
+       else
+               unused = bandw_raise;
        if( unused != unused_old) 
                printf plot_fmt, time, unused_old, time,unused >>"bandw_free";
        unused_old = unused;
@@ -360,6 +368,7 @@ function do_result(){               # process lines driver: result
        else {                                  # something bad from dumper 
                if ($7=="FAILED") { failed++;}
                else if ($7=="TRY-AGAIN"){ try++;}
+               else if ($7=="PORT") ;  # ignore from chunker
                else if ($7=="RQ-MORE-DISK") ;  # FIXME: ignore for now
                else if ($7=="NO-ROOM")  
                  print fil, pr_time($4),"#"  ++no_room, $0;