hw/altusmetrum
3 years agoExport all schematics, not just $*.sch
Keith Packard [Wed, 11 Nov 2020 19:49:34 +0000 (11:49 -0800)]
Export all schematics, not just $*.sch

Signed-off-by: Keith Packard <keithp@keithp.com>
3 years agoMake ssop-16 package match ft230 datasheet
Keith Packard [Wed, 23 Sep 2020 16:26:19 +0000 (09:26 -0700)]
Make ssop-16 package match ft230 datasheet

This required adding optional package width/height fields to ssop.5c
and then setting all of the parameters for ssop-16 in the makefile

Signed-off-by: Keith Packard <keithp@keithp.com>
3 years agoadd a coupe more .gitignore entires in the packages subtree to reduce noise
Bdale Garbee [Sun, 8 Nov 2020 17:03:12 +0000 (10:03 -0700)]
add a coupe more .gitignore entires in the packages subtree to reduce noise

3 years agocheck in my packages/.gitignore
Bdale Garbee [Sun, 8 Nov 2020 17:01:09 +0000 (10:01 -0700)]
check in my packages/.gitignore

3 years agodatasheet for CUI 5mm screw terminal strips
Bdale Garbee [Sun, 8 Nov 2020 16:58:12 +0000 (09:58 -0700)]
datasheet for CUI 5mm screw terminal strips

3 years agodatasheet for thermocouple connectors
Bdale Garbee [Sun, 8 Nov 2020 16:54:01 +0000 (09:54 -0700)]
datasheet for thermocouple connectors

3 years agodata sheet for high side switch on TeleStatic strand burner daughter card
Bdale Garbee [Sun, 8 Nov 2020 16:53:12 +0000 (09:53 -0700)]
data sheet for high side switch on TeleStatic strand burner daughter card

3 years agodatasheet for representative sample pressure sensor for TeleStatic
Bdale Garbee [Sun, 8 Nov 2020 16:51:39 +0000 (09:51 -0700)]
datasheet for representative sample pressure sensor for TeleStatic

3 years agoadd footprint for chosen thermocouple connector
Bdale Garbee [Tue, 3 Nov 2020 07:31:26 +0000 (00:31 -0700)]
add footprint for chosen thermocouple connector

3 years agodata sheet for MCP9808 temperature sensor
Bdale Garbee [Mon, 2 Nov 2020 08:16:17 +0000 (01:16 -0700)]
data sheet for MCP9808 temperature sensor

3 years agosymbol for MCP9808 temperature sensor
Bdale Garbee [Mon, 2 Nov 2020 08:15:13 +0000 (01:15 -0700)]
symbol for MCP9808 temperature sensor

3 years agopackage for MCP9808 temperature sensor
Bdale Garbee [Mon, 2 Nov 2020 08:04:19 +0000 (01:04 -0700)]
package for MCP9808 temperature sensor

3 years agoadd 14 pin connector symbol
Bdale Garbee [Sun, 1 Nov 2020 20:43:04 +0000 (13:43 -0700)]
add 14 pin connector symbol

3 years agoadd an un-branded C size title block to schematic symbols
Bdale Garbee [Sun, 1 Nov 2020 20:31:55 +0000 (13:31 -0700)]
add an un-branded C size title block to schematic symbols

3 years agoadd sot23-6 scad model
Bdale Garbee [Thu, 29 Oct 2020 16:44:25 +0000 (10:44 -0600)]
add sot23-6 scad model

3 years agoopenscad-compatible 3d part models, and Attribute entries to reference them
Bdale Garbee [Thu, 29 Oct 2020 16:24:58 +0000 (10:24 -0600)]
openscad-compatible 3d part models, and Attribute entries to reference them

3 years agoadd high side switch used on staticstrand to pref parts
Bdale Garbee [Sun, 25 Oct 2020 20:30:45 +0000 (14:30 -0600)]
add high side switch used on staticstrand to pref parts

3 years agosymbol for high-side power switch chosen for strand burner
Bdale Garbee [Thu, 22 Oct 2020 04:41:36 +0000 (22:41 -0600)]
symbol for high-side power switch chosen for strand burner

3 years agoadd 5mm pitch 6-screw strip for TeleStatic strand burner daughter
Bdale Garbee [Thu, 22 Oct 2020 00:12:06 +0000 (18:12 -0600)]
add 5mm pitch 6-screw strip for TeleStatic strand burner daughter

3 years agoadd footprints for CUI tb003-500 5mm pitch screw terminal strips
Bdale Garbee [Wed, 21 Oct 2020 23:42:32 +0000 (17:42 -0600)]
add footprints for CUI tb003-500 5mm pitch screw terminal strips

3 years agodata on male and female headers for TeleStatic
Bdale Garbee [Wed, 21 Oct 2020 22:44:24 +0000 (16:44 -0600)]
data on male and female headers for TeleStatic

3 years agocatalog with pick-n-place nuts for screw switches from Mouser
Bdale Garbee [Wed, 21 Oct 2020 22:43:16 +0000 (16:43 -0600)]
catalog with pick-n-place nuts for screw switches from Mouser

3 years agoMerge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum into master
Bdale Garbee [Wed, 21 Oct 2020 17:52:53 +0000 (11:52 -0600)]
Merge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum into master

3 years agoadd 40 pin male and female headers for TeleStatic system
Bdale Garbee [Wed, 21 Oct 2020 17:52:29 +0000 (11:52 -0600)]
add 40 pin male and female headers for TeleStatic system

3 years agooops, typo in beeper footprint name
Bdale Garbee [Thu, 1 Oct 2020 04:31:34 +0000 (22:31 -0600)]
oops, typo in beeper footprint name

3 years agonew beeper wanted by the AMSAT-NA guys for their LIHU board
Bdale Garbee [Thu, 1 Oct 2020 04:20:44 +0000 (22:20 -0600)]
new beeper wanted by the AMSAT-NA guys for their LIHU board

3 years agoMake ssop-16 package match ft230 datasheet
Keith Packard [Wed, 23 Sep 2020 16:26:19 +0000 (09:26 -0700)]
Make ssop-16 package match ft230 datasheet

This required adding optional package width/height fields to ssop.5c
and then setting all of the parameters for ssop-16 in the makefile

Signed-off-by: Keith Packard <keithp@keithp.com>
3 years agoGet pcb.mk working with lepton
Keith Packard [Wed, 23 Sep 2020 18:28:57 +0000 (11:28 -0700)]
Get pcb.mk working with lepton

Use bomAM for partslist.csv generation
use lepton-cli for generating pdf files

Signed-off-by: Keith Packard <keithp@keithp.com>
3 years agothe 22uF bulk LDO cap we're using on EasyMini/EasyTimer is actually 1206
Bdale Garbee [Sat, 19 Sep 2020 20:17:11 +0000 (14:17 -0600)]
the 22uF bulk LDO cap we're using on EasyMini/EasyTimer is actually 1206

3 years agoremove unused 22uF_35V cap from pref parts
Bdale Garbee [Sat, 19 Sep 2020 20:04:51 +0000 (14:04 -0600)]
remove unused 22uF_35V cap from pref parts

3 years agocheaper 1206 47uF cap with the same specs
Bdale Garbee [Sat, 19 Sep 2020 19:52:27 +0000 (13:52 -0600)]
cheaper 1206 47uF cap with the same specs

3 years agocreate a ToDo file to document work needed on Altus Metrum products
Bdale Garbee [Sat, 19 Sep 2020 04:55:29 +0000 (22:55 -0600)]
create a ToDo file to document work needed on Altus Metrum products

3 years agolost a bunch of connectors from preferred-parts that we don't actually use
Bdale Garbee [Fri, 18 Sep 2020 23:49:51 +0000 (17:49 -0600)]
lost a bunch of connectors from preferred-parts that we don't actually use

3 years agocleaning up preferred-parts, particularly rationalizing screw strip names
Bdale Garbee [Fri, 18 Sep 2020 23:16:29 +0000 (17:16 -0600)]
cleaning up preferred-parts, particularly rationalizing screw strip names

3 years agoremove loacl copy of tEDAx plugin for lepton-eda, use upstream version instead
Bdale Garbee [Fri, 18 Sep 2020 23:16:04 +0000 (17:16 -0600)]
remove loacl copy of tEDAx plugin for lepton-eda, use upstream version instead

3 years agorationalize EasyMini's memory part value nomenclature to match other products
Bdale Garbee [Fri, 18 Sep 2020 18:53:45 +0000 (12:53 -0600)]
rationalize EasyMini's memory part value nomenclature to match other products

3 years agomake imported scad models actually work as expected
Bdale Garbee [Wed, 9 Sep 2020 21:14:12 +0000 (15:14 -0600)]
make imported scad models actually work as expected

3 years agoimport initial set of scad 3d models from pcb-rnd distribution
Bdale Garbee [Wed, 9 Sep 2020 21:05:29 +0000 (15:05 -0600)]
import initial set of scad 3d models from pcb-rnd distribution

3 years agoadd slide switch, update metadata for TeleBT v4.0b build
Bdale Garbee [Wed, 19 Aug 2020 22:21:07 +0000 (16:21 -0600)]
add slide switch, update metadata for TeleBT v4.0b build

3 years agoupdate TeleBT box g-code for v4.0b and later with slide switch
Bdale Garbee [Wed, 19 Aug 2020 22:20:34 +0000 (16:20 -0600)]
update TeleBT box g-code for v4.0b and later with slide switch

3 years ago16x4 IR sensor array for on-track wheel temperature sensors
Bdale Garbee [Wed, 1 Jul 2020 04:58:02 +0000 (22:58 -0600)]
16x4 IR sensor array for on-track wheel temperature sensors

4 years ago0.1% resistors for EasyMotor pressure voltage divider
Bdale Garbee [Wed, 27 May 2020 04:06:22 +0000 (22:06 -0600)]
0.1% resistors for EasyMotor pressure voltage divider

4 years agoupdate ZOE footprint generator based on jlcpcb specs
Bdale Garbee [Tue, 19 May 2020 21:42:58 +0000 (15:42 -0600)]
update ZOE footprint generator based on jlcpcb specs

4 years agoremove attribs in clean target, so it stays fresh
Bdale Garbee [Mon, 18 May 2020 19:55:38 +0000 (13:55 -0600)]
remove attribs in clean target, so it stays fresh

4 years agoAdd parts for STM32l based µP
Keith Packard [Mon, 18 May 2020 00:41:44 +0000 (17:41 -0700)]
Add parts for STM32l based µP

Signed-off-by: Keith Packard <keithp@keithp.com>
4 years agopackages: add ufqfpn20 (stm32l tiny part)
Keith Packard [Mon, 18 May 2020 00:40:38 +0000 (17:40 -0700)]
packages: add ufqfpn20 (stm32l tiny part)

Signed-off-by: Keith Packard <keithp@keithp.com>
4 years agoadd a footprint for the u-blox ZOE
Bdale Garbee [Fri, 15 May 2020 03:28:04 +0000 (21:28 -0600)]
add a footprint for the u-blox ZOE

4 years agogive ZOE symbol a more useful footprint attribute
Bdale Garbee [Thu, 14 May 2020 14:52:47 +0000 (08:52 -0600)]
give ZOE symbol a more useful footprint attribute

4 years agofirst cut at a schematic symbol for the u-blox ZOE-M8Q chip
Bdale Garbee [Tue, 12 May 2020 08:59:41 +0000 (02:59 -0600)]
first cut at a schematic symbol for the u-blox ZOE-M8Q chip

4 years agoadd ZOE gps part and two potential regulator inductor choices
Bdale Garbee [Mon, 11 May 2020 15:43:39 +0000 (09:43 -0600)]
add ZOE gps part and two potential regulator inductor choices

4 years agoswitch 4.7uF 0402 pref part to a much cheaper 6.3V part (don't need 10V)
Bdale Garbee [Mon, 11 May 2020 15:33:31 +0000 (09:33 -0600)]
switch 4.7uF 0402 pref part to a much cheaper 6.3V part (don't need 10V)

4 years agodon't plan to provide resistors to AC for EasyTimer
Bdale Garbee [Mon, 4 May 2020 22:38:26 +0000 (16:38 -0600)]
don't plan to provide resistors to AC for EasyTimer

4 years agoresolve part out of stock at DK for EasyTimer build
Bdale Garbee [Mon, 4 May 2020 22:36:27 +0000 (16:36 -0600)]
resolve part out of stock at DK for EasyTimer build

4 years agogive LED tower base on TeleFireEight a bit more room to handle box tolerances
Bdale Garbee [Wed, 22 Apr 2020 23:40:02 +0000 (17:40 -0600)]
give LED tower base on TeleFireEight a bit more room to handle box tolerances

4 years agoremove u-blox EVA data, as we never used that part
Bdale Garbee [Sun, 19 Apr 2020 16:43:25 +0000 (10:43 -0600)]
remove u-blox EVA data, as we never used that part

4 years agoupdated u-blox antenna design notes
Bdale Garbee [Sun, 19 Apr 2020 16:37:54 +0000 (10:37 -0600)]
updated u-blox antenna design notes

4 years agoget fresh u-blox ZOE documents before designing with one
Bdale Garbee [Sun, 19 Apr 2020 16:27:42 +0000 (10:27 -0600)]
get fresh u-blox ZOE documents before designing with one

4 years agomore work on lht footprint generator - still not done
Bdale Garbee [Sun, 19 Apr 2020 16:26:39 +0000 (10:26 -0600)]
more work on lht footprint generator - still not done

4 years agosymbol for slide switch on revised TeleBT
Bdale Garbee [Sat, 14 Mar 2020 03:53:13 +0000 (21:53 -0600)]
symbol for slide switch on revised TeleBT

4 years agomake the mounting tabs on the switch body "pin 4" so I can ground them easily
Bdale Garbee [Sat, 14 Mar 2020 03:52:07 +0000 (21:52 -0600)]
make the mounting tabs on the switch body "pin 4" so I can ground them easily

4 years agoMerge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum
Bdale Garbee [Sun, 1 Mar 2020 04:23:48 +0000 (21:23 -0700)]
Merge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum

4 years agoAdd lc8812 (sk6812 with pins moved)
Keith Packard [Sun, 1 Mar 2020 01:56:57 +0000 (17:56 -0800)]
Add lc8812 (sk6812 with pins moved)

Signed-off-by: Keith Packard <keithp@keithp.com>
4 years agoAdd 'pads' around USB SMT connector tangs
Keith Packard [Wed, 8 Jan 2020 18:10:58 +0000 (10:10 -0800)]
Add 'pads' around USB SMT connector tangs

This makes sure there's bare copper around the tangs so that we get
enough solder stuck down there.

Signed-off-by: Keith Packard <keithp@keithp.com>
4 years agoint != float in python... sigh
Bdale Garbee [Sat, 29 Feb 2020 23:49:20 +0000 (16:49 -0700)]
int != float in python... sigh

4 years agoadd an SPDT switch symbol for TeleBT v4.0b
Bdale Garbee [Sat, 29 Feb 2020 19:38:47 +0000 (12:38 -0700)]
add an SPDT switch symbol for TeleBT v4.0b

4 years agomove push button switch to switches subdirectory for consistency
Bdale Garbee [Sat, 29 Feb 2020 19:29:55 +0000 (12:29 -0700)]
move push button switch to switches subdirectory for consistency

4 years agoslide switch for TeleBT version 4.0b
Bdale Garbee [Sat, 29 Feb 2020 19:26:43 +0000 (12:26 -0700)]
slide switch for TeleBT version 4.0b

4 years agouse lepton-cli to generate schematic pdf pages directly
Bdale Garbee [Tue, 25 Feb 2020 16:49:02 +0000 (09:49 -0700)]
use lepton-cli to generate schematic pdf pages directly

4 years agodata sheets for the voltage regulators on EasyMini and TeleMini
Bdale Garbee [Sun, 23 Feb 2020 07:46:32 +0000 (00:46 -0700)]
data sheets for the voltage regulators on EasyMini and TeleMini

4 years agofootprint for a new, smaller 16.384 Mhz crystal
Bdale Garbee [Sat, 15 Feb 2020 23:10:06 +0000 (16:10 -0700)]
footprint for a new, smaller 16.384 Mhz crystal

4 years agoadd 8-pin 50mil header footprint
Bdale Garbee [Sat, 15 Feb 2020 22:39:29 +0000 (15:39 -0700)]
add 8-pin 50mil header footprint

4 years agoadd BMX160 to pref parts for TeleMega v4.0 build
Bdale Garbee [Fri, 10 Jan 2020 15:58:36 +0000 (08:58 -0700)]
add BMX160 to pref parts for TeleMega v4.0 build

4 years agodon't default author and copyright assertion
Bdale Garbee [Fri, 10 Jan 2020 15:58:20 +0000 (08:58 -0700)]
don't default author and copyright assertion

4 years agoMerge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum
Bdale Garbee [Fri, 10 Jan 2020 15:48:45 +0000 (08:48 -0700)]
Merge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum

4 years agoupdated 47uF 1206 cap for availability prior to TeleMega v4 build
Bdale Garbee [Fri, 10 Jan 2020 15:47:11 +0000 (08:47 -0700)]
updated 47uF 1206 cap for availability prior to TeleMega v4 build

4 years agoitem per line in footprint script, better copyright handling
Bdale Garbee [Mon, 6 Jan 2020 06:49:05 +0000 (23:49 -0700)]
item per line in footprint script, better copyright handling

4 years agomove to python3 explicitly, per Debian policy
Bdale Garbee [Mon, 6 Jan 2020 05:19:41 +0000 (22:19 -0700)]
move to python3 explicitly, per Debian policy

4 years agoUse better pattern for generating all-drill.cnc
Keith Packard [Mon, 6 Jan 2020 01:21:49 +0000 (17:21 -0800)]
Use better pattern for generating all-drill.cnc

This matches whatever drill files are present, rather than generating
errors when one or the other is missing

Signed-off-by: Keith Packard <keithp@keithp.com>
4 years agoAdd TSX-3225 xtal footprint
Keith Packard [Mon, 6 Jan 2020 01:21:24 +0000 (17:21 -0800)]
Add TSX-3225 xtal footprint

Used on snekboard

Signed-off-by: Keith Packard <keithp@keithp.com>
4 years agoAdd ublox8 data sheets, along with a couple of xtals
Keith Packard [Mon, 6 Jan 2020 01:20:17 +0000 (17:20 -0800)]
Add ublox8 data sheets, along with a couple of xtals

Signed-off-by: Keith Packard <keithp@keithp.com>
4 years agoupdate Makefile to generate lht targets too
Bdale Garbee [Thu, 26 Dec 2019 14:42:49 +0000 (11:42 -0300)]
update Makefile to generate lht targets too

4 years agostart work on 11071 lihata footprint generator, improve license banners
Bdale Garbee [Thu, 26 Dec 2019 14:33:31 +0000 (11:33 -0300)]
start work on 11071 lihata footprint generator, improve license banners

4 years agocapture schematic symbols created by Bdale but not in git yet
Bdale Garbee [Thu, 26 Dec 2019 14:22:26 +0000 (11:22 -0300)]
capture schematic symbols created by Bdale but not in git yet

4 years agoadd a 2.75mm hole
Bdale Garbee [Thu, 26 Dec 2019 14:17:31 +0000 (11:17 -0300)]
add a 2.75mm hole

4 years agocreating stencils now uses a specialized cam job
Bdale Garbee [Thu, 26 Dec 2019 14:15:56 +0000 (11:15 -0300)]
creating stencils now uses a specialized cam job

4 years agoassume stdout which simplifies things significantly
Bdale Garbee [Thu, 26 Dec 2019 11:39:51 +0000 (08:39 -0300)]
assume stdout which simplifies things significantly

4 years agoworking on Python library to emit lht footprints
Bdale Garbee [Thu, 26 Dec 2019 11:28:54 +0000 (08:28 -0300)]
working on Python library to emit lht footprints

4 years agoupdate pref parts list to use 4ucon for all screw terminals
Bdale Garbee [Tue, 12 Nov 2019 23:14:06 +0000 (16:14 -0700)]
update pref parts list to use 4ucon for all screw terminals

4 years agobe more precise about mfg part number for MAX-8Q
Bdale Garbee [Wed, 9 Oct 2019 03:32:36 +0000 (21:32 -0600)]
be more precise about mfg part number for MAX-8Q

4 years agoupdate bomAM to reflect changes in lepton-eda 1.9.8 and later
Bdale Garbee [Fri, 4 Oct 2019 22:11:20 +0000 (16:11 -0600)]
update bomAM to reflect changes in lepton-eda 1.9.8 and later

4 years agoadd MAX-8Q to pref parts list since MAX-7Q is in short supply
Bdale Garbee [Fri, 4 Oct 2019 22:10:56 +0000 (16:10 -0600)]
add MAX-8Q to pref parts list since MAX-7Q is in short supply

4 years agomove wire hole to correct side, adjust cut-out dimensions per Terry's notes
Bdale Garbee [Tue, 1 Oct 2019 17:09:08 +0000 (11:09 -0600)]
move wire hole to correct side, adjust cut-out dimensions per Terry's notes

4 years agothin out side walls a bit per Terry's recommendation
Bdale Garbee [Tue, 24 Sep 2019 04:46:14 +0000 (22:46 -0600)]
thin out side walls a bit per Terry's recommendation

4 years agosymbol for Bosch BMX160 IMU
Bdale Garbee [Tue, 24 Sep 2019 04:45:26 +0000 (22:45 -0600)]
symbol for Bosch BMX160 IMU

4 years agoadd footprint for Bosch LGA14 used by BMX160
Bdale Garbee [Tue, 24 Sep 2019 04:27:25 +0000 (22:27 -0600)]
add footprint for Bosch LGA14 used by BMX160

4 years agoIPC reference doc on fiducial markers .. 1mm spot in 2mm mask opening works
Bdale Garbee [Tue, 17 Sep 2019 15:21:41 +0000 (09:21 -0600)]
IPC reference doc on fiducial markers .. 1mm spot in 2mm mask opening works

4 years agofix weird lip in pad number LCD opening
Bdale Garbee [Tue, 10 Sep 2019 17:56:52 +0000 (11:56 -0600)]
fix weird lip in pad number LCD opening

4 years agouse cut tape DK part number for resistors in pref parts
Bdale Garbee [Mon, 5 Aug 2019 04:43:15 +0000 (22:43 -0600)]
use cut tape DK part number for resistors in pref parts

4 years agomassive rework of fab targets in pcb-rnd.mk to use 'cam' output approach
Bdale Garbee [Mon, 5 Aug 2019 04:42:43 +0000 (22:42 -0600)]
massive rework of fab targets in pcb-rnd.mk to use 'cam' output approach

4 years ago9-axis part we might use for Mega products
Bdale Garbee [Thu, 1 Aug 2019 16:27:54 +0000 (10:27 -0600)]
9-axis part we might use for Mega products