Keith Packard [Sat, 2 Nov 2013 10:05:58 +0000 (03:05 -0700)]
Add CR32 footprint for sumida inductors. Customize QFN32 for FTDI
CR32 is the sumida series of large SMT wound inductors.
The FTDI footprint has square pads instead of rounded ones; that makes
cutting stencils at PSU a lot easier (it wrecks round pads somehow).
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 30 Sep 2013 16:49:28 +0000 (09:49 -0700)]
Add Murara piezo beeper pklcs1212 package and datasheet
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 28 Sep 2013 06:29:11 +0000 (23:29 -0700)]
Use existing geda SO20W footprint for holtek ht12d
Looks like this will work
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 28 Sep 2013 06:18:50 +0000 (23:18 -0700)]
Add footprint for statek cx1vsm crystal
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 28 Sep 2013 06:18:12 +0000 (23:18 -0700)]
Fix packages/Makefile -- missing backslash
Oops. Merging Makefile was done wrong.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 28 Sep 2013 06:09:47 +0000 (23:09 -0700)]
Merge remote-tracking branch 'origin/master'
Conflicts:
packages/Makefile
Keith Packard [Sat, 28 Sep 2013 06:05:23 +0000 (23:05 -0700)]
Fix FTDI ft232r-qfn symbol
Shuffle symbol pin locations around. Add ground pad.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 28 Sep 2013 06:04:26 +0000 (23:04 -0700)]
Add package for PJ-037A barrel connector
The usual Arduino power supply connector
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 28 Sep 2013 06:02:42 +0000 (23:02 -0700)]
Add symbol for holtek ht12d in 20sop package
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Sat, 28 Sep 2013 06:02:41 +0000 (00:02 -0600)]
data sheet for the crytal Tony wants for the Fox-1 command decoder
Bdale Garbee [Sat, 28 Sep 2013 05:52:38 +0000 (23:52 -0600)]
Merge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum
Conflicts:
packages/Makefile
Keith Packard [Sat, 28 Sep 2013 05:49:45 +0000 (22:49 -0700)]
Add holtek ht12d/ht12f 2¹² decoder data sheet
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Thu, 19 Sep 2013 22:14:14 +0000 (17:14 -0500)]
add new footprint for LT1963 on Fox IHU, have Makefile build recent footprints
Bdale Garbee [Mon, 16 Sep 2013 01:35:10 +0000 (19:35 -0600)]
first stab at designing an RF shield footprint for Fox-1 IHU
note that I don't know how to do "diagonal" pads, so the corners don't
connect right yet. also note that this design has not been reviewed or
approved by Tony or Bob and so should be considered subject to change...
Keith Packard [Sun, 8 Sep 2013 08:11:29 +0000 (01:11 -0700)]
Add FT232RQ symbol
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 8 Sep 2013 06:25:05 +0000 (23:25 -0700)]
Add bc4aa battery holder footprint
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 8 Sep 2013 06:01:52 +0000 (23:01 -0700)]
Add TFSOJ-8 footprint for AAT4901 H-bridge
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Fri, 6 Sep 2013 15:51:03 +0000 (09:51 -0600)]
data sheet for the LT1963A Tony wants me to use on the fox IHU v2
Keith Packard [Mon, 12 Aug 2013 09:12:33 +0000 (11:12 +0200)]
Add a tool to round BOM amounts to reasonable quantities
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 11 Aug 2013 21:10:06 +0000 (23:10 +0200)]
Change pin/pad clearance to 6mils on ufqfpn48
Make it work with both oshpark and 66each
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 11 Aug 2013 21:04:10 +0000 (23:04 +0200)]
Trim whitespace in partslist generation scheme
This makes the output cut&paste compatible with DK's text import
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 11 Aug 2013 21:02:57 +0000 (23:02 +0200)]
Fix ufqfpn48.5c to generate matching footprint
The .5c file was generating a different footprint, presumably due to
changes in the footprint.5c file
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Sun, 4 Aug 2013 19:57:38 +0000 (13:57 -0600)]
fix Taoglas passive patch footprint
Bdale Garbee [Sun, 28 Jul 2013 16:52:52 +0000 (10:52 -0600)]
`Merge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum
Bdale Garbee [Sun, 28 Jul 2013 16:52:33 +0000 (10:52 -0600)]
app note that was buried in the telebt tree
Keith Packard [Fri, 19 Jul 2013 17:52:01 +0000 (10:52 -0700)]
Add side-firing 0603 LED footprint
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Fri, 19 Jul 2013 15:21:01 +0000 (09:21 -0600)]
merge more data sheets
Keith Packard [Mon, 15 Jul 2013 22:25:20 +0000 (15:25 -0700)]
Change LPH footprint to use just pins 1 and 2
No reason to label all four pins when they're internally connected
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 15 Jul 2013 22:08:05 +0000 (15:08 -0700)]
Add LPH series switch footprint
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sat, 13 Jul 2013 10:31:55 +0000 (03:31 -0700)]
Add 2mm pitch pin header package
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 11 Jul 2013 06:00:38 +0000 (23:00 -0700)]
Add ublox-7 hardware integration manual
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 7 Jul 2013 19:42:27 +0000 (12:42 -0700)]
Flip MLP 4x3 package around
Was drawn looking at the bottom rather than the top. Not so useful
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 7 Jul 2013 19:25:55 +0000 (12:25 -0700)]
Add SAW filter symbol
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 7 Jul 2013 19:09:50 +0000 (12:09 -0700)]
Add 1.4mm x 1.0mm SAW filter package
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 13 Jun 2013 02:49:50 +0000 (19:49 -0700)]
Create footprint for Taoglas 1575.18.4.A.02 GPS patch antenna
A bit of clever hacking -- a pad is defined around the hole on the
bottom side to which the antenna will be soldered. No metal occurs on
the top side around the pin
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 7 Jun 2013 23:29:04 +0000 (16:29 -0700)]
Don't include 'no-load' parts in vendor partslist
Make sure the partslist includes only components actually to be loaded
on the board.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Fri, 7 Jun 2013 18:02:30 +0000 (11:02 -0700)]
Add 4mmx3mm MLP8 package (for smaller flash parts)
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Thu, 16 May 2013 00:42:41 +0000 (18:42 -0600)]
capture FDS9926A data sheet for posterity
Bdale Garbee [Tue, 7 May 2013 03:16:52 +0000 (21:16 -0600)]
data sheet for AXSEM ax5051, can do BPSK on 70cm but RX sensitivity poor?
Bdale Garbee [Sun, 5 May 2013 14:09:27 +0000 (08:09 -0600)]
footprint for GPS patched used on TeleMetrum v0.2
Bdale Garbee [Sat, 4 May 2013 05:17:55 +0000 (23:17 -0600)]
add cc110l transceiver data sheet and errata
Bdale Garbee [Thu, 2 May 2013 17:06:24 +0000 (11:06 -0600)]
merge footprints needed for TeleMetrum v1.2b
Bdale Garbee [Thu, 2 May 2013 17:03:22 +0000 (11:03 -0600)]
merge symbols needed for TeleMetrum v1.2b
Bdale Garbee [Fri, 26 Apr 2013 03:13:30 +0000 (21:13 -0600)]
datasheet for 4050
Bdale Garbee [Fri, 26 Apr 2013 00:23:25 +0000 (18:23 -0600)]
Merge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum
Bdale Garbee [Fri, 26 Apr 2013 00:23:12 +0000 (18:23 -0600)]
merge symbols and footprints needed for TeleTerra
Keith Packard [Wed, 24 Apr 2013 00:38:41 +0000 (17:38 -0700)]
Merge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum
Bdale Garbee [Tue, 23 Apr 2013 23:43:12 +0000 (17:43 -0600)]
symbol and footprint for Rayson BTM-182 Bluetooth(tm) module
Keith Packard [Sat, 13 Apr 2013 05:03:54 +0000 (22:03 -0700)]
Add stm32l discovery schematic
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Fri, 12 Apr 2013 17:51:00 +0000 (11:51 -0600)]
add data sheet for power switch on telebt, teleterra, etc
Bdale Garbee [Mon, 8 Apr 2013 20:18:35 +0000 (14:18 -0600)]
Merge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum
Bdale Garbee [Mon, 8 Apr 2013 20:18:07 +0000 (14:18 -0600)]
fix up dual led to have centered XYRS, and to include a cathode end dot
Keith Packard [Tue, 2 Apr 2013 04:50:43 +0000 (21:50 -0700)]
Add clearance around the 1007 footprint pads
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Tue, 2 Apr 2013 03:55:56 +0000 (20:55 -0700)]
Add 1007 footprint
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 1 Apr 2013 23:11:27 +0000 (16:11 -0700)]
CC1120 has a new footprint. Add datasheet and footprint generator
The only change from the 1120 footprint is to make the center pad a
bit smaller. The docs have a much more elaborate change, but that
involves putting vias in the middle of the solder paste area, which
seems like a bad plan unless we used a via-in-pad process.
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 31 Mar 2013 09:39:50 +0000 (02:39 -0700)]
Make footprint files depend on footprint.5c
Can't tell which are nickle and which are python, so just recompile
them all when footprint.5c changes
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 31 Mar 2013 09:36:27 +0000 (02:36 -0700)]
Compute solder mask from process clearance in pad_mm_clear
Instead of using the user specified clearance (which is often zero),
use the process clearance to make sure there is sufficient solder mask
clearance around the pad. If the user really wants zero mask, they can
use pad_mm_clear_mask
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Tue, 26 Mar 2013 03:37:40 +0000 (21:37 -0600)]
Merge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum
Bdale Garbee [Tue, 26 Mar 2013 03:37:29 +0000 (21:37 -0600)]
data sheets from telegps merged
Keith Packard [Tue, 26 Mar 2013 03:13:24 +0000 (20:13 -0700)]
Add RFPA0133 data sheet
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 25 Mar 2013 03:59:16 +0000 (20:59 -0700)]
Add cc115l data sheet
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Sun, 24 Mar 2013 18:32:53 +0000 (11:32 -0700)]
Add ARMv7-M architecture reference manual
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 21 Mar 2013 18:51:10 +0000 (11:51 -0700)]
Add ground pad to STML151-48 symbol
The pad under this chip is tied to ground and needs to be connected
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 21 Mar 2013 18:27:58 +0000 (11:27 -0700)]
Add footprints from telegps
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Thu, 21 Mar 2013 18:19:27 +0000 (11:19 -0700)]
Add symbols from telegps
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 20 Mar 2013 21:13:58 +0000 (14:13 -0700)]
Actually add the ABM8.py footprint file
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 20 Mar 2013 20:27:58 +0000 (13:27 -0700)]
Build ABM8 package
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 20 Mar 2013 06:04:38 +0000 (23:04 -0700)]
Add LPCXpresso docs (devel board for LPC11U14)
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Wed, 20 Mar 2013 20:26:32 +0000 (14:26 -0600)]
fix errors in 8ufson2x2 footprint generator
Bdale Garbee [Wed, 20 Mar 2013 05:35:22 +0000 (23:35 -0600)]
use a less generic name for the comparator footprint
Bdale Garbee [Wed, 20 Mar 2013 05:30:37 +0000 (23:30 -0600)]
joint title block for EasyMetrum
Keith Packard [Wed, 20 Mar 2013 04:41:41 +0000 (21:41 -0700)]
Add DFN8 footprint (for lm293 comparators)
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Wed, 20 Mar 2013 04:29:15 +0000 (21:29 -0700)]
Rename lm293 data sheet to lm293.pdf
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Wed, 20 Mar 2013 04:26:55 +0000 (22:26 -0600)]
Merge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum
Bdale Garbee [Wed, 20 Mar 2013 04:26:36 +0000 (22:26 -0600)]
fix lpc11u1x symbol, add new comparator data sheet
Keith Packard [Mon, 18 Mar 2013 23:17:53 +0000 (16:17 -0700)]
Add packages and symbols from µPusb
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 18 Mar 2013 23:07:44 +0000 (16:07 -0700)]
Move packages for micropeak over
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 18 Mar 2013 22:46:20 +0000 (15:46 -0700)]
Add pico-ezmate footprints
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Mon, 18 Mar 2013 22:12:42 +0000 (16:12 -0600)]
footprints needed for megadongle
Bdale Garbee [Mon, 18 Mar 2013 22:08:41 +0000 (16:08 -0600)]
mini USB symbol
Bdale Garbee [Mon, 18 Mar 2013 22:03:26 +0000 (16:03 -0600)]
move dual LED into the new diodes/ subdir
Bdale Garbee [Mon, 18 Mar 2013 22:00:54 +0000 (16:00 -0600)]
actually build diodes footprint(s)
Keith Packard [Mon, 18 Mar 2013 21:52:59 +0000 (14:52 -0700)]
avoid parallel make when rebuilding packages
Maybe this will make things happier?
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 18 Mar 2013 21:52:15 +0000 (14:52 -0700)]
Add powerdi123 footprint
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Mon, 18 Mar 2013 21:55:50 +0000 (15:55 -0600)]
remainder of footprint generators needed for megametrum
Bdale Garbee [Mon, 18 Mar 2013 21:53:18 +0000 (15:53 -0600)]
add molex footprint builders
Bdale Garbee [Mon, 18 Mar 2013 21:50:26 +0000 (15:50 -0600)]
add footprint generators for JST connectors
Bdale Garbee [Mon, 18 Mar 2013 21:45:24 +0000 (15:45 -0600)]
dual op-amp symbol useful for LMV393, LM6142, et al
Bdale Garbee [Mon, 18 Mar 2013 21:41:25 +0000 (15:41 -0600)]
more symbols needed for MegaMetrum, et al
Bdale Garbee [Mon, 18 Mar 2013 21:32:04 +0000 (15:32 -0600)]
two more package generators
Bdale Garbee [Mon, 18 Mar 2013 21:23:17 +0000 (15:23 -0600)]
add .gitignore hack back to packages/ top level Makefile
Keith Packard [Mon, 18 Mar 2013 21:18:52 +0000 (14:18 -0700)]
Ignore built footprints
Signed-off-by: Keith Packard <keithp@keithp.com>
Bdale Garbee [Mon, 18 Mar 2013 21:14:42 +0000 (15:14 -0600)]
add LPCC16 footprint for HMC5883L
Bdale Garbee [Mon, 18 Mar 2013 21:13:41 +0000 (15:13 -0600)]
add lqfp footprint generators for STM parts
Bdale Garbee [Mon, 18 Mar 2013 21:09:14 +0000 (15:09 -0600)]
Merge branch 'master' of ssh://git.gag.com/scm/git/hw/altusmetrum
Conflicts:
packages/Makefile
Bdale Garbee [Mon, 18 Mar 2013 21:07:15 +0000 (15:07 -0600)]
add Diodes, Inc datasheet directory and the part I want to use for ldo input
Bdale Garbee [Mon, 18 Mar 2013 21:06:53 +0000 (15:06 -0600)]
add a bunch of packages
Bdale Garbee [Mon, 18 Mar 2013 21:05:41 +0000 (15:05 -0600)]
update Makefile to process subdirs and have a clean target
Keith Packard [Mon, 18 Mar 2013 20:59:30 +0000 (13:59 -0700)]
Automatically generate suitable .gitignore in packages directory
Ignore built packages
Signed-off-by: Keith Packard <keithp@keithp.com>
Keith Packard [Mon, 18 Mar 2013 20:57:12 +0000 (13:57 -0700)]
Add symbols for MicroPeak
Signed-off-by: Keith Packard <keithp@keithp.com>
projects / hw / altusmetrum / log