2022-05-24 |
Bdale Garbee | add zener to protect ADC load cell input |
blob | commitdiff | raw |
2022-05-21 |
Bdale Garbee | improve metadata, note about painting strands |
blob | commitdiff | raw | diff to current |
2020-11-12 |
Bdale Garbee | update schematic metadata to use larger flash chip |
blob | commitdiff | raw | diff to current |
2020-10-25 |
Bdale Garbee | update schematic to properly reflect unconnected SOC... |
blob | commitdiff | raw | diff to current |
2020-10-21 |
Bdale Garbee | modify header pinout to support strand burner daughter... |
blob | commitdiff | raw | diff to current |
2020-10-21 |
Bdale Garbee | rationalize screw strip values in pref parts |
blob | commitdiff | raw | diff to current |
2020-10-21 |
Bdale Garbee | getting there |
blob | commitdiff | raw | diff to current |
2020-10-21 |
Bdale Garbee | 40 pin header fully wired up |
blob | commitdiff | raw | diff to current |
2020-10-21 |
Bdale Garbee | PC* all routed to header, drc clean |
blob | commitdiff | raw | diff to current |
2020-10-21 |
Bdale Garbee | work in progress, two color errors I need to fix in... |
blob | commitdiff | raw | diff to current |
2020-10-21 |
Bdale Garbee | update layer colors, lots of work done on routing |
blob | commitdiff | raw | diff to current |
2020-10-21 |
Bdale Garbee | work in progress |
blob | commitdiff | raw | diff to current |
2020-10-21 |
Bdale Garbee | move to smaller 16 MHz CPU crystal, start assigning... |
blob | commitdiff | raw | diff to current |
2020-10-21 |
Bdale Garbee | lots of work on placement for revised and simplified... |
blob | commitdiff | raw | diff to current |
2020-10-21 |
Bdale Garbee | change board to 3x3 inches, add 40-pin header for expan... |
blob | commitdiff | raw | diff to current |
2020-10-21 |
Bdale Garbee | add header for ADC spi channel to aid debugging |
blob | commitdiff | raw | diff to current |
2019-07-29 |
Bdale Garbee | change FET input series resistors to 1k |
blob | commitdiff | raw | diff to current |
2019-03-27 |
Bdale Garbee | add p-fet battery polarity protection fab-old-v3 |
blob | commitdiff | raw | diff to current |
2019-03-27 |
Bdale Garbee | add another resistor so we can detect a FET that fails... |
blob | commitdiff | raw | diff to current |
2019-03-27 |
Bdale Garbee | move to MicroMatch for thermistor cabling, reduce board... |
blob | commitdiff | raw | diff to current |
2019-03-25 |
Bdale Garbee | swap armed and continuity LEDs to ease routing |
blob | commitdiff | raw | diff to current |
2019-03-10 |
Bdale Garbee | switch to ADS131A04 for the sensor ADC |
blob | commitdiff | raw | diff to current |
2019-03-10 |
Bdale Garbee | change thermistor connector to 2x5 header for easy... |
blob | commitdiff | raw | diff to current |
2019-02-09 |
Bdale Garbee | update copyright assertion to 2019 |
blob | commitdiff | raw | diff to current |
2018-12-05 |
Bdale Garbee | route complete, drc clean, could use copper massaging... |
blob | commitdiff | raw | diff to current |
2018-12-05 |
Bdale Garbee | a pile more work on the layout |
blob | commitdiff | raw | diff to current |
2018-11-24 |
Bdale Garbee | initial cut at schematic for test stand v3, still needs... |
blob | commitdiff | raw | diff to current |
|