tcl: Adapt config files to new ftdi command syntax

The patch was created automatically using the following
script:

%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---
(cat << EOF
ftdi_device_desc ftdi device_desc
ftdi_serial ftdi serial
ftdi_channel ftdi channel
ftdi_layout_init ftdi layout_init
ftdi_layout_signal ftdi layout_signal
ftdi_set_signal ftdi set_signal
ftdi_get_signal ftdi get_signal
ftdi_vid_pid ftdi vid_pid
ftdi_tdo_sample_edge ftdi tdo_sample_edge
EOF
) | while read a b; do
sed -i "s/$a/$b/g" $(find tcl -type f -name "*.cfg" )
done
%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---%<---

Change-Id: Iff781f37bb5511b7e15cbe6dcdf6d28e89fb174f
Signed-off-by: Marc Schink <dev@zapb.de>
Reviewed-on: http://openocd.zylin.com/6333
Tested-by: jenkins
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>

diff --git a/tcl/board/digilent_analog_discovery.cfg b/tcl/board/digilent_analog_discovery.cfg
index 954e5400835bda3081b8c8ac7bc9fbe9c6b91ea6..64cdacfa89f8aacf3878ec4f0c18929eb0dce0fa 100644 (file)
--- a/tcl/board/digilent_analog_discovery.cfg
+++ b/tcl/board/digilent_analog_discovery.cfg
@@ -8,10 +8,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Digilent USB Device"
-ftdi_vid_pid 0x0403 0x6014
+ftdi device_desc "Digilent USB Device"
+ftdi vid_pid 0x0403 0x6014
 
-ftdi_layout_init 0x8008 0x800b
+ftdi layout_init 0x8008 0x800b
 
 adapter speed 25000
 

diff --git a/tcl/board/digilent_nexys_video.cfg b/tcl/board/digilent_nexys_video.cfg
index f171e240322dca5dc6bffb3a873d6e93212167d8..b60ec912fc73764e49d8856be9aee36efd20e3fb 100644 (file)
--- a/tcl/board/digilent_nexys_video.cfg
+++ b/tcl/board/digilent_nexys_video.cfg
@@ -6,19 +6,19 @@
 adapter driver ftdi
 adapter speed 30000
 
-ftdi_device_desc "Digilent USB Device"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Digilent USB Device"
+ftdi vid_pid 0x0403 0x6010
 
 # channel 0 is dedicated for Digilent's DPTI Interface
 # channel 1 is used for JTAG
-ftdi_channel 1
+ftdi channel 1
 
 # just TCK TDI TDO TMS, no reset
-ftdi_layout_init 0x0088 0x008b
+ftdi layout_init 0x0088 0x008b
 reset_config none
 
 # Enable sampling on falling edge for high JTAG speeds.
-ftdi_tdo_sample_edge falling
+ftdi tdo_sample_edge falling
 
 transport select jtag
 

diff --git a/tcl/board/dp_busblaster_v3.cfg b/tcl/board/dp_busblaster_v3.cfg
index a9974d9bcb3f22efa3d476d8b7222b1143ee956c..b94b43a0b94461446e3ff423f2f73e148ca8719f 100644 (file)
--- a/tcl/board/dp_busblaster_v3.cfg
+++ b/tcl/board/dp_busblaster_v3.cfg
@@ -8,6 +8,6 @@
 #
 
 source [find interface/ftdi/dp_busblaster.cfg]
-ftdi_channel 1
+ftdi channel 1
 
 jtag newtap xc2c32a tap -expected-id 0x06e1c093 -irlen 8

diff --git a/tcl/board/dp_busblaster_v4.cfg b/tcl/board/dp_busblaster_v4.cfg
index 7b3bee8fcfbf7cc309f06655f9ff4a3863743f8b..2c2f0e9d1a80831cf20f53ef0d954ec2837ffaf0 100644 (file)
--- a/tcl/board/dp_busblaster_v4.cfg
+++ b/tcl/board/dp_busblaster_v4.cfg
@@ -14,6 +14,6 @@
 #
 
 source [find interface/ftdi/dp_busblaster.cfg]
-ftdi_channel 1
+ftdi channel 1
 
 jtag newtap xc2c64a tap -expected-id 0x06e5c093 -irlen 8

diff --git a/tcl/board/gumstix-aerocore.cfg b/tcl/board/gumstix-aerocore.cfg
index f0103ed451eb6a7a2a066273148864daf523619c..565df4cf88bf322259036d128d4027204dd6c79b 100644 (file)
--- a/tcl/board/gumstix-aerocore.cfg
+++ b/tcl/board/gumstix-aerocore.cfg
@@ -1,10 +1,10 @@
 # JTAG for the STM32F4x chip used on the Gumstix AeroCore is available on
 # the first interface of a Quad FTDI chip.  nTRST is bit 4.
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6011
+ftdi vid_pid 0x0403 0x6011
 
-ftdi_layout_init 0x0000 0x001b
-ftdi_layout_signal nTRST -data 0x0010
+ftdi layout_init 0x0000 0x001b
+ftdi layout_signal nTRST -data 0x0010
 
 source [find target/stm32f4x.cfg]
 reset_config trst_only

diff --git a/tcl/board/kasli.cfg b/tcl/board/kasli.cfg
index d492249ba3c3444cb66f1649fc17e7ffe5dc0559..7cfdcf20e98607f84ff36d62818b7b4c0e084eb1 100644 (file)
--- a/tcl/board/kasli.cfg
+++ b/tcl/board/kasli.cfg
@@ -1,8 +1,8 @@
 adapter driver ftdi
-ftdi_device_desc "Quad RS232-HS"
-ftdi_vid_pid 0x0403 0x6011
-ftdi_channel 0
-ftdi_layout_init 0x0008 0x000b
+ftdi device_desc "Quad RS232-HS"
+ftdi vid_pid 0x0403 0x6011
+ftdi channel 0
+ftdi layout_init 0x0008 0x000b
 # adapter usb location 1:8
 
 reset_config none

diff --git a/tcl/board/kindle2.cfg b/tcl/board/kindle2.cfg
index a39f15c672567627b0883569952ed65d7bc9f363..71dca741c9633c29765533e3caf62b04e7922e23 100644 (file)
--- a/tcl/board/kindle2.cfg
+++ b/tcl/board/kindle2.cfg
@@ -37,7 +37,7 @@ jtag_ntrst_delay 30
 arm11 memwrite burst disable
 
 adapter speed 1000
-ftdi_tdo_sample_edge falling
+ftdi tdo_sample_edge falling
 
 proc kindle2_init {} {
        imx3x_reset

diff --git a/tcl/board/nds32_corvettef1.cfg b/tcl/board/nds32_corvettef1.cfg
index cec172342307a42ef9331ad1778c7d8b90a21a7b..7300ce04a2a96bdc112cabace4ac757ac6181717 100644 (file)
--- a/tcl/board/nds32_corvettef1.cfg
+++ b/tcl/board/nds32_corvettef1.cfg
@@ -7,12 +7,12 @@
 adapter speed     10000
 
 adapter driver ftdi
-ftdi_device_desc "Dual RS232-HS"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Dual RS232-HS"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0c08 0x0f1b
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_init 0x0c08 0x0f1b
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800
 reset_config srst_only
 
 source [find target/nds32v5.cfg]

diff --git a/tcl/board/numato_mimas_a7.cfg b/tcl/board/numato_mimas_a7.cfg
index d4012bada735ccb1190d4be8b5537cbe9e380e27..12df8913dce6afd59b207cd3bf841ed9a11d29c9 100644 (file)
--- a/tcl/board/numato_mimas_a7.cfg
+++ b/tcl/board/numato_mimas_a7.cfg
@@ -8,13 +8,13 @@
 #       Therefore, prefer external power supply.
 
 adapter driver ftdi
-ftdi_device_desc "Mimas Artix 7 FPGA Module"
-ftdi_vid_pid 0x2a19 0x1009
+ftdi device_desc "Mimas Artix 7 FPGA Module"
+ftdi vid_pid 0x2a19 0x1009
 
 # channel 0 is for custom purpose by users (like uart, fifo etc)
 # channel 1 is reserved for JTAG (by-default) or SPI (possible via changing solder jumpers)
-ftdi_channel 1
-ftdi_tdo_sample_edge falling
+ftdi channel 1
+ftdi tdo_sample_edge falling
 
 
 # FTDI Pin Layout
@@ -28,7 +28,7 @@ ftdi_tdo_sample_edge falling
 # OE_N is JTAG buffer output enable signal (active-low)
 # PROG_B is not used, so left as input to FTDI.
 #
-ftdi_layout_init 0x0008 0x004b
+ftdi layout_init 0x0008 0x004b
 reset_config none
 adapter speed 30000
 

diff --git a/tcl/board/quark_d2000_refboard.cfg b/tcl/board/quark_d2000_refboard.cfg
index 8b8314a0ea815f02ad58715a776917fb60c1c4bc..a89895d89b0ca30812b837a2453fb810b2ce5749 100644 (file)
--- a/tcl/board/quark_d2000_refboard.cfg
+++ b/tcl/board/quark_d2000_refboard.cfg
@@ -2,11 +2,11 @@
 
 # the board has an onboard FTDI FT232H chip
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6014
-ftdi_channel 0
+ftdi vid_pid 0x0403 0x6014
+ftdi channel 0
 
-ftdi_layout_init 0x0000 0x030b
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0100
+ftdi layout_init 0x0000 0x030b
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0100
 
 source [find target/quark_d20xx.cfg]
 

diff --git a/tcl/board/sayma_amc.cfg b/tcl/board/sayma_amc.cfg
index 64c0854285e155b329dff11743f7c8e716f70580..0bd76ba01ebae1049002b383317964cd2519079e 100644 (file)
--- a/tcl/board/sayma_amc.cfg
+++ b/tcl/board/sayma_amc.cfg
@@ -11,19 +11,19 @@
 # which features an Artix 7 FPGA.
 
 adapter driver ftdi
-ftdi_device_desc "Quad RS232-HS"
-ftdi_vid_pid 0x0403 0x6011
-ftdi_channel 0
+ftdi device_desc "Quad RS232-HS"
+ftdi vid_pid 0x0403 0x6011
+ftdi channel 0
 # Use this to distinguish multiple boards by topology
 #adapter usb location 5:1
 # sampling on falling edge generally seems to work and accelerates things but
 # is not fully tested
-#ftdi_tdo_sample_edge falling
+#ftdi tdo_sample_edge falling
 # EN_USB_JTAG on ADBUS7: out, high
 # USB_nTRST on ADBUS4: out, high, but R46 is DNP
-ftdi_layout_init 0x0098 0x008b
-#ftdi_layout_signal EN_USB -data 0x0080
-#ftdi_layout_signal nTRST -data 0x0010
+ftdi layout_init 0x0098 0x008b
+#ftdi layout_signal EN_USB -data 0x0080
+#ftdi layout_signal nTRST -data 0x0010
 reset_config none
 
 adapter speed 5000

diff --git a/tcl/board/sifive-e31arty.cfg b/tcl/board/sifive-e31arty.cfg
index b7a255ea252892ca0f3285420b24f63121f5e9b2..8e701f15639c90ac36552b24574bfc297c81e32f 100644 (file)
--- a/tcl/board/sifive-e31arty.cfg
+++ b/tcl/board/sifive-e31arty.cfg
@@ -14,8 +14,8 @@ $_TARGETNAME.0 configure -work-area-phys 0x80000000 -work-area-size 10000 -work-
 flash bank spi0 fespi 0x40000000 0 0 0 $_TARGETNAME.0 0x20004000
 init
 if {[ info exists pulse_srst]} {
-  ftdi_set_signal nSRST 0
-  ftdi_set_signal nSRST z
+  ftdi set_signal nSRST 0
+  ftdi set_signal nSRST z
 }
 halt
 flash protect 0 64 last off

diff --git a/tcl/board/sifive-e51arty.cfg b/tcl/board/sifive-e51arty.cfg
index 20ad575517155b3ea875f244da1f747ffec813bf..a543987bb47ea06708a5d57e3dbe59990502c08d 100644 (file)
--- a/tcl/board/sifive-e51arty.cfg
+++ b/tcl/board/sifive-e51arty.cfg
@@ -14,8 +14,8 @@ $_TARGETNAME.0 configure -work-area-phys 0x80000000 -work-area-size 10000 -work-
 flash bank spi0 fespi 0x40000000 0 0 0 $_TARGETNAME.0 0x20004000
 init
 if {[ info exists pulse_srst]} {
-  ftdi_set_signal nSRST 0
-  ftdi_set_signal nSRST z
+  ftdi set_signal nSRST 0
+  ftdi set_signal nSRST z
 }
 halt
 flash protect 0 64 last off

diff --git a/tcl/board/sifive-hifive1.cfg b/tcl/board/sifive-hifive1.cfg
index 196f540bbaa04fe799914a595d27b444b8f5aa15..c47485bf238c5cd7f3b255d2b87835942a254660 100644 (file)
--- a/tcl/board/sifive-hifive1.cfg
+++ b/tcl/board/sifive-hifive1.cfg
@@ -1,15 +1,15 @@
 adapter speed     10000
 
 adapter driver ftdi
-ftdi_device_desc "Dual RS232-HS"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Dual RS232-HS"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0008 0x001b
-ftdi_layout_signal nSRST -oe 0x0020 -data 0x0020
+ftdi layout_init 0x0008 0x001b
+ftdi layout_signal nSRST -oe 0x0020 -data 0x0020
 
 #Reset Stretcher logic on FE310 is ~1 second long
 #This doesn't apply if you use
-# ftdi_set_signal, but still good to document
+# ftdi set_signal, but still good to document
 #adapter srst delay 1500
 
 set _CHIPNAME riscv
@@ -23,8 +23,8 @@ flash bank onboard_spi_flash fespi 0x20000000 0 0 0 $_TARGETNAME
 init
 #reset -- This type of reset is not implemented yet
 if {[ info exists pulse_srst]} {
-  ftdi_set_signal nSRST 0
-  ftdi_set_signal nSRST z
+  ftdi set_signal nSRST 0
+  ftdi set_signal nSRST z
   #Wait for the reset stretcher
   #It will work without this, but
   #will incur lots of delays for later commands.

diff --git a/tcl/board/ti_tmdx570ls20susb.cfg b/tcl/board/ti_tmdx570ls20susb.cfg
index 87cab2690747e3a64e282b6feb9810ddffc05789..e71136cfeab2602df14b6d1c18578874f3eff10c 100644 (file)
--- a/tcl/board/ti_tmdx570ls20susb.cfg
+++ b/tcl/board/ti_tmdx570ls20susb.cfg
@@ -12,5 +12,5 @@ reset_config trst_only
 
 # xds100v2 config says add this to the end
 init
-ftdi_set_signal PWR_RST 1
+ftdi set_signal PWR_RST 1
 jtag arp_init

diff --git a/tcl/interface/ftdi/100ask-openjtag.cfg b/tcl/interface/ftdi/100ask-openjtag.cfg
index 3cbd37e06d8664b775c9be6eb95459cc3103a580..a12df97af2d6689534cfff7aad8464752494d562 100644 (file)
--- a/tcl/interface/ftdi/100ask-openjtag.cfg
+++ b/tcl/interface/ftdi/100ask-openjtag.cfg
@@ -8,9 +8,9 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "USB<=>JTAG&RS232"
-ftdi_vid_pid 0x1457 0x5118
+ftdi device_desc "USB<=>JTAG&RS232"
+ftdi vid_pid 0x1457 0x5118
 
-ftdi_layout_init 0x0f08 0x0f1b
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_init 0x0f08 0x0f1b
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400

diff --git a/tcl/interface/ftdi/axm0432.cfg b/tcl/interface/ftdi/axm0432.cfg
index 6cc1752e242c38e0371295e97eab76de44ab2452..84b77a69abc0e3bf0b6c477466a33a30d920f07c 100644 (file)
--- a/tcl/interface/ftdi/axm0432.cfg
+++ b/tcl/interface/ftdi/axm0432.cfg
@@ -10,9 +10,9 @@ echo "Please report your experience with this file to openocd-devel mailing list
 echo "so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "Symphony SoundBite"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Symphony SoundBite"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0c08 0x0c2b
-ftdi_layout_signal nTRST -data 0x0800
-ftdi_layout_signal nSRST -data 0x0400
+ftdi layout_init 0x0c08 0x0c2b
+ftdi layout_signal nTRST -data 0x0800
+ftdi layout_signal nSRST -data 0x0400

diff --git a/tcl/interface/ftdi/c232hm.cfg b/tcl/interface/ftdi/c232hm.cfg
index 27cf7667457ea9a8f229b44bc768f3da1dc4b2bc..25fcae1b0bc8aac1b12055072cc5224bd8fd12c5 100644 (file)
--- a/tcl/interface/ftdi/c232hm.cfg
+++ b/tcl/interface/ftdi/c232hm.cfg
@@ -14,18 +14,18 @@
 # http://www.ftdichip.com/Support/Documents/AppNotes/AN_129_FTDI_Hi_Speed_USB_To_JTAG_Example.pdf
 
 adapter driver ftdi
-#ftdi_device_desc "C232HM-DDHSL-0"
-#ftdi_device_desc "C232HM-EDHSL-0"
+#ftdi device_desc "C232HM-DDHSL-0"
+#ftdi device_desc "C232HM-EDHSL-0"
 
 # Common PID for FT232H
-ftdi_vid_pid 0x0403 0x6014
+ftdi vid_pid 0x0403 0x6014
 
 # Layout
 # High data byte 0x40 configures red LED on ACBUS6 initially high (unlit, since active-low)
 # Low data byte 0x08 configures TMS on ACBUS3 initially high (asserted); TCK, TDI low
 # High direction byte 0x40 configures red LED on ACBUS6 as high (output)
 # Low direction byte 0x0b configures TDO on ACBUS2 as low (input)
-ftdi_layout_init 0x4008 0x400b
+ftdi layout_init 0x4008 0x400b
 
 # ---A*BUS-------CCCCCCCC|DDDDDDDD
 # --------\______76543210|76543210
@@ -35,12 +35,12 @@ ftdi_layout_init 0x4008 0x400b
 #GPIOL2        0x0040 = 00000000|01000000 = ADBUS6
 #GPIOL3        0x0080 = 00000000|10000000 = ADBUS7
 # -ndata treats the LED as active-low for expected behavior (toggle when transferring)
-ftdi_layout_signal LED -ndata 0x4000
+ftdi layout_signal LED -ndata 0x4000
 # Available for aliasing as desired
-ftdi_layout_signal GPIOL0 -data 0x0010 -oe 0x0010
-ftdi_layout_signal GPIOL1 -data 0x0020 -oe 0x0020
-ftdi_layout_signal GPIOL2 -data 0x0040 -oe 0x0040
-ftdi_layout_signal GPIOL3 -data 0x0080 -oe 0x0080
+ftdi layout_signal GPIOL0 -data 0x0010 -oe 0x0010
+ftdi layout_signal GPIOL1 -data 0x0020 -oe 0x0020
+ftdi layout_signal GPIOL2 -data 0x0040 -oe 0x0040
+ftdi layout_signal GPIOL3 -data 0x0080 -oe 0x0080
 
 # C232HM               FT232H  JTAG/Other
 # Num  Color   Name    Func

diff --git a/tcl/interface/ftdi/calao-usb-a9260-c01.cfg b/tcl/interface/ftdi/calao-usb-a9260-c01.cfg
index a23ddbfb5e268876667ee1edd89f66d44c798e04..41e5973914601f5aec4e459d5c8825f27e99a5d9 100644 (file)
--- a/tcl/interface/ftdi/calao-usb-a9260-c01.cfg
+++ b/tcl/interface/ftdi/calao-usb-a9260-c01.cfg
@@ -11,12 +11,12 @@ echo "experience with this file to openocd-devel mailing list, so it could be ma
 echo "as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "USB-A9260"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "USB-A9260"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0c08 0x0f1b
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_init 0x0c08 0x0f1b
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800
 
 script interface/calao-usb-a9260.cfg
 script target/at91sam9260minimal.cfg

diff --git a/tcl/interface/ftdi/calao-usb-a9260-c02.cfg b/tcl/interface/ftdi/calao-usb-a9260-c02.cfg
index 67427c5c0a7379fea13967c967d76b620122eb3a..001aef59cb2cfb7c4010c83daeeee0dedc2889f4 100644 (file)
--- a/tcl/interface/ftdi/calao-usb-a9260-c02.cfg
+++ b/tcl/interface/ftdi/calao-usb-a9260-c02.cfg
@@ -11,12 +11,12 @@ echo "experience with this file to openocd-devel mailing list, so it could be ma
 echo "as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "USB-A9260"
-ftdi_vid_pid 0x0403 0x6001
+ftdi device_desc "USB-A9260"
+ftdi vid_pid 0x0403 0x6001
 
-ftdi_layout_init 0x0c08 0x0f1b
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_init 0x0c08 0x0f1b
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800
 
 script interface/calao-usb-a9260.cfg
 script target/at91sam9260minimal.cfg

diff --git a/tcl/interface/ftdi/cortino.cfg b/tcl/interface/ftdi/cortino.cfg
index 2bc516cc60d3454e4698a292209745ed7b131298..c0eae310524f5aef757471a5440f8b9922d107a1 100644 (file)
--- a/tcl/interface/ftdi/cortino.cfg
+++ b/tcl/interface/ftdi/cortino.cfg
@@ -5,9 +5,9 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Cortino"
-ftdi_vid_pid 0x0640 0x0032
+ftdi device_desc "Cortino"
+ftdi vid_pid 0x0640 0x0032
 
-ftdi_layout_init 0x0108 0x010b
-ftdi_layout_signal nTRST -data 0x0100
-ftdi_layout_signal nSRST -data 0x0200 -oe 0x0200
+ftdi layout_init 0x0108 0x010b
+ftdi layout_signal nTRST -data 0x0100
+ftdi layout_signal nSRST -data 0x0200 -oe 0x0200

diff --git a/tcl/interface/ftdi/digilent-hs1.cfg b/tcl/interface/ftdi/digilent-hs1.cfg
index dfba3393ad26d1aaede5be2c61ef2a862d1d8f0e..55391b9d314c826300decad65d1fd7bd638c78b8 100644 (file)
--- a/tcl/interface/ftdi/digilent-hs1.cfg
+++ b/tcl/interface/ftdi/digilent-hs1.cfg
@@ -2,10 +2,10 @@
 # (the later being the OEM on-board version)
 
 adapter driver ftdi
-ftdi_device_desc "Digilent Adept USB Device"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Digilent Adept USB Device"
+ftdi vid_pid 0x0403 0x6010
 # channel 1 does not have any functionality
-ftdi_channel 0
+ftdi channel 0
 # just TCK TDI TDO TMS, no reset
-ftdi_layout_init 0x0088 0x008b
+ftdi layout_init 0x0088 0x008b
 reset_config none

diff --git a/tcl/interface/ftdi/digilent-hs2.cfg b/tcl/interface/ftdi/digilent-hs2.cfg
index ae6ba01bb34448b3ca25735b72f94ad00dbdaad7..269eca0f38f3e37cb9f063578e63a9f73af6716d 100644 (file)
--- a/tcl/interface/ftdi/digilent-hs2.cfg
+++ b/tcl/interface/ftdi/digilent-hs2.cfg
@@ -1,10 +1,10 @@
 # this supports JTAG-HS2 (and apparently Nexys4 as well)
 
 adapter driver ftdi
-ftdi_device_desc "Digilent Adept USB Device"
-ftdi_vid_pid 0x0403 0x6014
+ftdi device_desc "Digilent Adept USB Device"
+ftdi vid_pid 0x0403 0x6014
 
-ftdi_channel 0
-ftdi_layout_init 0x00e8 0x60eb
+ftdi channel 0
+ftdi layout_init 0x00e8 0x60eb
 
 reset_config none

diff --git a/tcl/interface/ftdi/digilent_jtag_hs3.cfg b/tcl/interface/ftdi/digilent_jtag_hs3.cfg
index 7160bed8e7cdb5a1ae301ba35b5cbd904b6d9f18..ca2807f80c7b97671453a3115eced602971ee4d2 100644 (file)
--- a/tcl/interface/ftdi/digilent_jtag_hs3.cfg
+++ b/tcl/interface/ftdi/digilent_jtag_hs3.cfg
@@ -3,11 +3,11 @@
 #
 
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6014
-ftdi_device_desc "Digilent USB Device"
+ftdi vid_pid 0x0403 0x6014
+ftdi device_desc "Digilent USB Device"
 
 # From Digilent support:
 # The SRST pin is [...] 0x20 and 0x10 is the /OE (active low output enable)
 
-ftdi_layout_init 0x2088 0x308b
-ftdi_layout_signal nSRST -data 0x2000 -noe 0x1000
+ftdi layout_init 0x2088 0x308b
+ftdi layout_signal nSRST -data 0x2000 -noe 0x1000

diff --git a/tcl/interface/ftdi/digilent_jtag_smt2.cfg b/tcl/interface/ftdi/digilent_jtag_smt2.cfg
index 55f278bdc60c3117d7ddd736cb8bf3099382065b..f4ba27befe0c53011d86e1ee0a214cd0b09a4b4c 100644 (file)
--- a/tcl/interface/ftdi/digilent_jtag_smt2.cfg
+++ b/tcl/interface/ftdi/digilent_jtag_smt2.cfg
@@ -8,10 +8,10 @@
 #
 
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6014
+ftdi vid_pid 0x0403 0x6014
 
-ftdi_layout_init 0x20e8 0x3feb
-ftdi_layout_signal nSRST -data 0x2000
-ftdi_layout_signal GPIO2 -data 0x2000
-ftdi_layout_signal GPIO1 -data 0x0200
-ftdi_layout_signal GPIO0 -data 0x0100
+ftdi layout_init 0x20e8 0x3feb
+ftdi layout_signal nSRST -data 0x2000
+ftdi layout_signal GPIO2 -data 0x2000
+ftdi layout_signal GPIO1 -data 0x0200
+ftdi layout_signal GPIO0 -data 0x0100

diff --git a/tcl/interface/ftdi/digilent_jtag_smt2_nc.cfg b/tcl/interface/ftdi/digilent_jtag_smt2_nc.cfg
index bc783a46cbac636ef4f39586b50bc041a0c3828f..a143cd7720c3b78a5115e93a2768f4adb45bf55b 100644 (file)
--- a/tcl/interface/ftdi/digilent_jtag_smt2_nc.cfg
+++ b/tcl/interface/ftdi/digilent_jtag_smt2_nc.cfg
@@ -8,11 +8,11 @@
 # https://www.xilinx.com/products/boards-and-kits/kcu105.html#documentation
 #
 # Note that the digilent_jtag_smt2 layout does not work and hangs while
-# the ftdi_device_desc from digilent_hs2 is wrong.
+# the ftdi device_desc from digilent_hs2 is wrong.
 
 adapter driver ftdi
-ftdi_device_desc "Digilent USB Device"
-ftdi_vid_pid 0x0403 0x6014
-ftdi_channel 0
-ftdi_layout_init 0x00e8 0x60eb
+ftdi device_desc "Digilent USB Device"
+ftdi vid_pid 0x0403 0x6014
+ftdi channel 0
+ftdi layout_init 0x00e8 0x60eb
 reset_config none

diff --git a/tcl/interface/ftdi/dlp-usb1232h.cfg b/tcl/interface/ftdi/dlp-usb1232h.cfg
index 9ddc2c80a856e79801d276a356232ccfb3f5774f..e9651dd9943a686b54f00ba0105b9bfa32bdcfaf 100644 (file)
--- a/tcl/interface/ftdi/dlp-usb1232h.cfg
+++ b/tcl/interface/ftdi/dlp-usb1232h.cfg
@@ -13,9 +13,9 @@ echo "in ft2232.c. Please report your experience with this file to openocd-devel
 echo "mailing list, so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "Dual RS232-HS"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Dual RS232-HS"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0008 0x000b
-ftdi_layout_signal nTRST -data 0x0010 -oe 0x0010
-ftdi_layout_signal nSRST -data 0x0040 -oe 0x0040
+ftdi layout_init 0x0008 0x000b
+ftdi layout_signal nTRST -data 0x0010 -oe 0x0010
+ftdi layout_signal nSRST -data 0x0040 -oe 0x0040

diff --git a/tcl/interface/ftdi/dp_busblaster.cfg b/tcl/interface/ftdi/dp_busblaster.cfg
index 86ab4d8408588a7a9b6fd50c787ea3fc997bcbb7..420f788d2f3d8a4e0f7ce616c3e8fee467213002 100644 (file)
--- a/tcl/interface/ftdi/dp_busblaster.cfg
+++ b/tcl/interface/ftdi/dp_busblaster.cfg
@@ -12,9 +12,9 @@ echo "Info : If you need SWD support, flash KT-Link buffer from https://github.c
 and use dp_busblaster_kt-link.cfg instead"
 
 adapter driver ftdi
-ftdi_device_desc "Dual RS232-HS"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Dual RS232-HS"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0c08 0x0f1b
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_init 0x0c08 0x0f1b
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800

diff --git a/tcl/interface/ftdi/dp_busblaster_kt-link.cfg b/tcl/interface/ftdi/dp_busblaster_kt-link.cfg
index d49a4c98f401cd33e61986cce2a981416a249bca..4924d261928f03ec88f89f0fd8ff922578ecf2ae 100644 (file)
--- a/tcl/interface/ftdi/dp_busblaster_kt-link.cfg
+++ b/tcl/interface/ftdi/dp_busblaster_kt-link.cfg
@@ -10,12 +10,12 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Dual RS232-HS"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Dual RS232-HS"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x8c28 0xff3b
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
-ftdi_layout_signal LED -ndata 0x8000
-ftdi_layout_signal SWD_EN -ndata 0x0020 -oe 0x2000
-ftdi_layout_signal SWDIO_OE -ndata 0x1000
+ftdi layout_init 0x8c28 0xff3b
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_signal LED -ndata 0x8000
+ftdi layout_signal SWD_EN -ndata 0x0020 -oe 0x2000
+ftdi layout_signal SWDIO_OE -ndata 0x1000

diff --git a/tcl/interface/ftdi/flossjtag-noeeprom.cfg b/tcl/interface/ftdi/flossjtag-noeeprom.cfg
index 42ed18ec3c1b8d355f4781b51b63135ea08dc4e0..7083e638814c25a96065791d59fcaed2944f2034 100644 (file)
--- a/tcl/interface/ftdi/flossjtag-noeeprom.cfg
+++ b/tcl/interface/ftdi/flossjtag-noeeprom.cfg
@@ -18,9 +18,9 @@ echo "Please report your experience with this file to openocd-devel mailing list
 echo "so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "Dual RS232-HS"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Dual RS232-HS"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0008 0x000b
-ftdi_layout_signal nTRST -data 0x0010 -oe 0x0010
-ftdi_layout_signal nSRST -data 0x0040 -oe 0x0040
+ftdi layout_init 0x0008 0x000b
+ftdi layout_signal nTRST -data 0x0010 -oe 0x0010
+ftdi layout_signal nSRST -data 0x0040 -oe 0x0040

diff --git a/tcl/interface/ftdi/flossjtag.cfg b/tcl/interface/ftdi/flossjtag.cfg
index c4ad81dccb6cafc29fd2af92fa9364daded176af..2e3cfca4895706f9a47621a00026ae4df8758f61 100644 (file)
--- a/tcl/interface/ftdi/flossjtag.cfg
+++ b/tcl/interface/ftdi/flossjtag.cfg
@@ -18,12 +18,12 @@ echo "Please report your experience with this file to openocd-devel mailing list
 echo "so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6010
-ftdi_device_desc "FLOSS-JTAG"
-#ftdi_serial "FJ000001"
+ftdi vid_pid 0x0403 0x6010
+ftdi device_desc "FLOSS-JTAG"
+#ftdi serial "FJ000001"
 
-ftdi_layout_init 0x0008 0x180b
-ftdi_layout_signal nTRST -data 0x0010 -oe 0x0010
-ftdi_layout_signal nSRST -data 0x0040 -oe 0x0040
-ftdi_layout_signal LED -data 0x0800
-ftdi_layout_signal LED2 -data 0x1000
+ftdi layout_init 0x0008 0x180b
+ftdi layout_signal nTRST -data 0x0010 -oe 0x0010
+ftdi layout_signal nSRST -data 0x0040 -oe 0x0040
+ftdi layout_signal LED -data 0x0800
+ftdi layout_signal LED2 -data 0x1000

diff --git a/tcl/interface/ftdi/flyswatter.cfg b/tcl/interface/ftdi/flyswatter.cfg
index 0b849ad53d454b62568f6f2ba345c1d38dbad02f..bfa015b2cc7c174cbc085685f310bd924897ed48 100644 (file)
--- a/tcl/interface/ftdi/flyswatter.cfg
+++ b/tcl/interface/ftdi/flyswatter.cfg
@@ -5,10 +5,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Flyswatter"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Flyswatter"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0818 0x0cfb
-ftdi_layout_signal nTRST -data 0x0010
-ftdi_layout_signal nSRST -oe 0x0020
-ftdi_layout_signal LED -data 0x0c00
+ftdi layout_init 0x0818 0x0cfb
+ftdi layout_signal nTRST -data 0x0010
+ftdi layout_signal nSRST -oe 0x0020
+ftdi layout_signal LED -data 0x0c00

diff --git a/tcl/interface/ftdi/flyswatter2.cfg b/tcl/interface/ftdi/flyswatter2.cfg
index 4f4a1f819b6c960013ff5881fa4ec6ad7fc52357..0b4a8ef9f243ac7ca08c71fe73ef78a33ef74287 100644 (file)
--- a/tcl/interface/ftdi/flyswatter2.cfg
+++ b/tcl/interface/ftdi/flyswatter2.cfg
@@ -5,10 +5,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Flyswatter2"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Flyswatter2"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0538 0x057b
-ftdi_layout_signal LED -ndata 0x0400
-ftdi_layout_signal nTRST -data 0x0010
-ftdi_layout_signal nSRST -data 0x0020 -noe 0x0100
+ftdi layout_init 0x0538 0x057b
+ftdi layout_signal LED -ndata 0x0400
+ftdi layout_signal nTRST -data 0x0010
+ftdi layout_signal nSRST -data 0x0020 -noe 0x0100

diff --git a/tcl/interface/ftdi/ft232h-module-swd.cfg b/tcl/interface/ftdi/ft232h-module-swd.cfg
index 98a8c844fd2b98d259ea409977e0263f28c83858..7fa4283596f6e2ee6d81ddd5fe6056ff77854230 100644 (file)
--- a/tcl/interface/ftdi/ft232h-module-swd.cfg
+++ b/tcl/interface/ftdi/ft232h-module-swd.cfg
@@ -8,27 +8,27 @@
 
 adapter driver ftdi
 
-ftdi_vid_pid 0x0403 0x6014
+ftdi vid_pid 0x0403 0x6014
 
 # data MSB..LSB       direction (1:out) MSB..LSB
 # 0000'0000'0011'0000 0000'0000'0011'1011
-ftdi_layout_init 0x0030 0x003b
+ftdi layout_init 0x0030 0x003b
 # 0xfff8 0xfffb
 # Those signal are only required on some platforms or may required to be
 # enabled explicitly (e.g. nrf5x chips).
-ftdi_layout_signal nSRST -data 0x0010 -oe 0x0010
-ftdi_layout_signal nTRST -data 0x0020 -oe 0x0020
+ftdi layout_signal nSRST -data 0x0010 -oe 0x0010
+ftdi layout_signal nTRST -data 0x0020 -oe 0x0020
 
 # swd enable
-ftdi_layout_signal SWD_EN -data 0
+ftdi layout_signal SWD_EN -data 0
 # tri-state (configure as input) TDO/TIO when reading
-ftdi_layout_signal SWDIO_OE -data 0
+ftdi layout_signal SWDIO_OE -data 0
 
 transport select swd
 
 # re-configure TDO as tri-state
-#ftdi_layout_signal TDO -data 0x0002 -oe 0x0002
-#ftdi_layout_signal TDI -data 0x0004
+#ftdi layout_signal TDO -data 0x0002 -oe 0x0002
+#ftdi layout_signal TDI -data 0x0004
 
 # Adafruit      FT232H    JTAG       SWD
 # Name  Pin     Name      Func       Func

diff --git a/tcl/interface/ftdi/gw16042.cfg b/tcl/interface/ftdi/gw16042.cfg
index 1288f77b18a70f27ba70dd1aadbc032db417ceea..ef318293858bb7d318f245e3857ae880d0570e58 100644 (file)
--- a/tcl/interface/ftdi/gw16042.cfg
+++ b/tcl/interface/ftdi/gw16042.cfg
@@ -18,9 +18,9 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "USB-JTAG"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "USB-JTAG"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0058 0x007b
-ftdi_layout_signal nTRST -data 0x0010
-ftdi_layout_signal nSRST -oe 0x0020
+ftdi layout_init 0x0058 0x007b
+ftdi layout_signal nTRST -data 0x0010
+ftdi layout_signal nSRST -oe 0x0020

diff --git a/tcl/interface/ftdi/hie-jtag.cfg b/tcl/interface/ftdi/hie-jtag.cfg
index 39af87d8924fcb81c676ea67211096424daf601a..6694df0484bb95344df514b0c6062645797c6444 100644 (file)
--- a/tcl/interface/ftdi/hie-jtag.cfg
+++ b/tcl/interface/ftdi/hie-jtag.cfg
@@ -6,15 +6,15 @@
 #
 
 adapter driver ftdi
-ftdi_channel 0
-ftdi_vid_pid 0x0403 0x6014
-ftdi_device_desc "HIE JTAG Debugger"
+ftdi channel 0
+ftdi vid_pid 0x0403 0x6014
+ftdi device_desc "HIE JTAG Debugger"
 
-ftdi_layout_init 0x0c08 0x4f1b
+ftdi layout_init 0x0c08 0x4f1b
 
 # define both Reset signals
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800
 
 # Toggle USB LED
-ftdi_layout_signal LED -ndata 0x4000
+ftdi layout_signal LED -ndata 0x4000

diff --git a/tcl/interface/ftdi/hilscher_nxhx10_etm.cfg b/tcl/interface/ftdi/hilscher_nxhx10_etm.cfg
index 3802f6d2cdefce50155c67ea054339f55252d152..d55f636deba3f481a37d12e11c812405775334cc 100644 (file)
--- a/tcl/interface/ftdi/hilscher_nxhx10_etm.cfg
+++ b/tcl/interface/ftdi/hilscher_nxhx10_etm.cfg
@@ -10,9 +10,9 @@ echo "Please report your experience with this file to openocd-devel mailing list
 echo "so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "NXHX 10-ETM"
-ftdi_vid_pid 0x0640 0x0028
+ftdi device_desc "NXHX 10-ETM"
+ftdi vid_pid 0x0640 0x0028
 
-ftdi_layout_init 0x0308 0x030b
-ftdi_layout_signal nTRST -data 0x0100
-ftdi_layout_signal nSRST -data 0x0200
+ftdi layout_init 0x0308 0x030b
+ftdi layout_signal nTRST -data 0x0100
+ftdi layout_signal nSRST -data 0x0200

diff --git a/tcl/interface/ftdi/hilscher_nxhx500_etm.cfg b/tcl/interface/ftdi/hilscher_nxhx500_etm.cfg
index f2e64b4f5ebc2e48f59e089c0372d5c0218d12c3..8c7981561709b76d5ca6e0ff5c90a279f895e449 100644 (file)
--- a/tcl/interface/ftdi/hilscher_nxhx500_etm.cfg
+++ b/tcl/interface/ftdi/hilscher_nxhx500_etm.cfg
@@ -10,9 +10,9 @@ echo "Please report your experience with this file to openocd-devel mailing list
 echo "so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "NXHX 500-ETM"
-ftdi_vid_pid 0x0640 0x0028
+ftdi device_desc "NXHX 500-ETM"
+ftdi vid_pid 0x0640 0x0028
 
-ftdi_layout_init 0x0308 0x030b
-ftdi_layout_signal nTRST -data 0x0100
-ftdi_layout_signal nSRST -data 0x0200
+ftdi layout_init 0x0308 0x030b
+ftdi layout_signal nTRST -data 0x0100
+ftdi layout_signal nSRST -data 0x0200

diff --git a/tcl/interface/ftdi/hilscher_nxhx500_re.cfg b/tcl/interface/ftdi/hilscher_nxhx500_re.cfg
index 38f3c690e4ee68748e433114ef36cbf493c50956..9aa2cd5167d6d94978031eb843dfa316754003cc 100644 (file)
--- a/tcl/interface/ftdi/hilscher_nxhx500_re.cfg
+++ b/tcl/interface/ftdi/hilscher_nxhx500_re.cfg
@@ -10,9 +10,9 @@ echo "Please report your experience with this file to openocd-devel mailing list
 echo "so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "NXHX 500-RE"
-ftdi_vid_pid 0x0640 0x0028
+ftdi device_desc "NXHX 500-RE"
+ftdi vid_pid 0x0640 0x0028
 
-ftdi_layout_init 0x0308 0x030b
-ftdi_layout_signal nTRST -data 0x0100
-ftdi_layout_signal nSRST -data 0x0200
+ftdi layout_init 0x0308 0x030b
+ftdi layout_signal nTRST -data 0x0100
+ftdi layout_signal nSRST -data 0x0200

diff --git a/tcl/interface/ftdi/hilscher_nxhx50_etm.cfg b/tcl/interface/ftdi/hilscher_nxhx50_etm.cfg
index bff081f184b165c922da86c106bf61ff51396dd6..a64d0e8a480546ca03abcf5f4c99a82186d65604 100644 (file)
--- a/tcl/interface/ftdi/hilscher_nxhx50_etm.cfg
+++ b/tcl/interface/ftdi/hilscher_nxhx50_etm.cfg
@@ -10,9 +10,9 @@ echo "Please report your experience with this file to openocd-devel mailing list
 echo "so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "NXHX 50-ETM"
-ftdi_vid_pid 0x0640 0x0028
+ftdi device_desc "NXHX 50-ETM"
+ftdi vid_pid 0x0640 0x0028
 
-ftdi_layout_init 0x0308 0x030b
-ftdi_layout_signal nTRST -data 0x0100
-ftdi_layout_signal nSRST -data 0x0200
+ftdi layout_init 0x0308 0x030b
+ftdi layout_signal nTRST -data 0x0100
+ftdi layout_signal nSRST -data 0x0200

diff --git a/tcl/interface/ftdi/hilscher_nxhx50_re.cfg b/tcl/interface/ftdi/hilscher_nxhx50_re.cfg
index f9fbd015a50420f014b426e2503206d6951e92ef..277883675aac12818cb30a12ecd4ea9b7438dd5f 100644 (file)
--- a/tcl/interface/ftdi/hilscher_nxhx50_re.cfg
+++ b/tcl/interface/ftdi/hilscher_nxhx50_re.cfg
@@ -10,9 +10,9 @@ echo "Please report your experience with this file to openocd-devel mailing list
 echo "so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "NXHX50-RE"
-ftdi_vid_pid 0x0640 0x0028
+ftdi device_desc "NXHX50-RE"
+ftdi vid_pid 0x0640 0x0028
 
-ftdi_layout_init 0x0308 0x030b
-ftdi_layout_signal nTRST -data 0x0100
-ftdi_layout_signal nSRST -data 0x0200
+ftdi layout_init 0x0308 0x030b
+ftdi layout_signal nTRST -data 0x0100
+ftdi layout_signal nSRST -data 0x0200

diff --git a/tcl/interface/ftdi/hitex_lpc1768stick.cfg b/tcl/interface/ftdi/hitex_lpc1768stick.cfg
index 9fe80f126b438165fec922eefd0f7997d74216b9..87affe84ad953771a09d8162f311609715248072 100644 (file)
--- a/tcl/interface/ftdi/hitex_lpc1768stick.cfg
+++ b/tcl/interface/ftdi/hitex_lpc1768stick.cfg
@@ -6,9 +6,9 @@
 
 
 adapter driver ftdi
-ftdi_device_desc "LPC1768-Stick"
-ftdi_vid_pid 0x0640 0x0026
+ftdi device_desc "LPC1768-Stick"
+ftdi vid_pid 0x0640 0x0026
 
-ftdi_layout_init 0x0388 0x038b
-ftdi_layout_signal nTRST -data 0x0100
-ftdi_layout_signal nSRST -data 0x0080 -noe 0x200
+ftdi layout_init 0x0388 0x038b
+ftdi layout_signal nTRST -data 0x0100
+ftdi layout_signal nSRST -data 0x0080 -noe 0x200

diff --git a/tcl/interface/ftdi/hitex_str9-comstick.cfg b/tcl/interface/ftdi/hitex_str9-comstick.cfg
index 2b3dc3690e1431fca20cab0c5b99ff0a2abd4d35..6490d65f480d970e69b7789fd0cd5ea6d7256de3 100644 (file)
--- a/tcl/interface/ftdi/hitex_str9-comstick.cfg
+++ b/tcl/interface/ftdi/hitex_str9-comstick.cfg
@@ -5,9 +5,9 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "STR9-comStick"
-ftdi_vid_pid 0x0640 0x002c
+ftdi device_desc "STR9-comStick"
+ftdi vid_pid 0x0640 0x002c
 
-ftdi_layout_init 0x0108 0x010b
-ftdi_layout_signal nTRST -data 0x0100
-ftdi_layout_signal nSRST -data 0x0200 -oe 0x0200
+ftdi layout_init 0x0108 0x010b
+ftdi layout_signal nTRST -data 0x0100
+ftdi layout_signal nSRST -data 0x0200 -oe 0x0200

diff --git a/tcl/interface/ftdi/icebear.cfg b/tcl/interface/ftdi/icebear.cfg
index 04c27319ed4a3193e1271ac14985daf2f5f7d8af..76b2102a570f13a8744579a218fe6eec95847615 100644 (file)
--- a/tcl/interface/ftdi/icebear.cfg
+++ b/tcl/interface/ftdi/icebear.cfg
@@ -10,9 +10,9 @@ echo "Please report your experience with this file to openocd-devel mailing list
 echo "so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "ICEbear JTAG adapter"
-ftdi_vid_pid 0x0403 0xc140
+ftdi device_desc "ICEbear JTAG adapter"
+ftdi vid_pid 0x0403 0xc140
 
-ftdi_layout_init 0x0028 0x002b
-ftdi_layout_signal nTRST -data 0x0010 -oe 0x0010
-ftdi_layout_signal nSRST -data 0x0020
+ftdi layout_init 0x0028 0x002b
+ftdi layout_signal nTRST -data 0x0010 -oe 0x0010
+ftdi layout_signal nSRST -data 0x0020

diff --git a/tcl/interface/ftdi/imx8mp-evk.cfg b/tcl/interface/ftdi/imx8mp-evk.cfg
index 4e04e8cd7f5e9831149b6f900dc47f534ddcf410..64f3f3db0ca55ffe9c03303d81d6a6e35115f5a4 100644 (file)
--- a/tcl/interface/ftdi/imx8mp-evk.cfg
+++ b/tcl/interface/ftdi/imx8mp-evk.cfg
@@ -11,18 +11,18 @@
 #
 
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6011
-ftdi_channel 0
+ftdi vid_pid 0x0403 0x6011
+ftdi channel 0
 
-ftdi_layout_init 0x00f8 0x000b
+ftdi layout_init 0x00f8 0x000b
 
-ftdi_layout_signal RESET_B     -data 0x0010 -oe 0x0010
+ftdi layout_signal RESET_B     -data 0x0010 -oe 0x0010
 # Called SYS_nRST in schematics
-ftdi_layout_signal nSRST       -data 0x0020 -oe 0x0020
-ftdi_layout_signal IO_nRST     -data 0x0040 -oe 0x0040
-ftdi_layout_signal ONOFF_B     -data 0x0080 -oe 0x0080
+ftdi layout_signal nSRST       -data 0x0020 -oe 0x0020
+ftdi layout_signal IO_nRST     -data 0x0040 -oe 0x0040
+ftdi layout_signal ONOFF_B     -data 0x0080 -oe 0x0080
 
-ftdi_layout_signal GPIO1       -data 0x0100 -oe 0x0100
-ftdi_layout_signal GPIO2       -data 0x0200 -oe 0x0200
-ftdi_layout_signal GPIO3       -data 0x0400 -oe 0x0400
-ftdi_layout_signal GPIO4       -data 0x0800 -oe 0x0800
+ftdi layout_signal GPIO1       -data 0x0100 -oe 0x0100
+ftdi layout_signal GPIO2       -data 0x0200 -oe 0x0200
+ftdi layout_signal GPIO3       -data 0x0400 -oe 0x0400
+ftdi layout_signal GPIO4       -data 0x0800 -oe 0x0800

diff --git a/tcl/interface/ftdi/incircuit-icprog.cfg b/tcl/interface/ftdi/incircuit-icprog.cfg
index e0bd5ef5914711fe46c065bbbd6480aeba29a2a3..a200954469a7aa06164f50af9ce66fb31b753580 100644 (file)
--- a/tcl/interface/ftdi/incircuit-icprog.cfg
+++ b/tcl/interface/ftdi/incircuit-icprog.cfg
@@ -7,8 +7,8 @@
 #
 
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6010
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0508 0x0f1b
-ftdi_layout_signal nSRST -noe 0x0400 -data 0x0800
-ftdi_layout_signal nTRST -noe 0x0100 -data 0x0200
+ftdi layout_init 0x0508 0x0f1b
+ftdi layout_signal nSRST -noe 0x0400 -data 0x0800
+ftdi layout_signal nTRST -noe 0x0100 -data 0x0200

diff --git a/tcl/interface/ftdi/iotlab-usb.cfg b/tcl/interface/ftdi/iotlab-usb.cfg
index caa0596fd9637c73dd37165c9285168e5a1e2b83..92ffa840bdba47fbd97ec49958267349695e670a 100644 (file)
--- a/tcl/interface/ftdi/iotlab-usb.cfg
+++ b/tcl/interface/ftdi/iotlab-usb.cfg
@@ -4,8 +4,8 @@
 #
 
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6010
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0008 0x000b
-ftdi_layout_signal nTRST -data 0x0010 -oe 0x0010
-ftdi_layout_signal nSRST -data 0x0040 -oe 0x0040
+ftdi layout_init 0x0008 0x000b
+ftdi layout_signal nTRST -data 0x0010 -oe 0x0010
+ftdi layout_signal nSRST -data 0x0040 -oe 0x0040

diff --git a/tcl/interface/ftdi/isodebug.cfg b/tcl/interface/ftdi/isodebug.cfg
index ead28644ceec97a51f104e2a02775f5fef32721d..018998963e3d3258bd302e7143f06f65f969ccb9 100644 (file)
--- a/tcl/interface/ftdi/isodebug.cfg
+++ b/tcl/interface/ftdi/isodebug.cfg
@@ -2,26 +2,26 @@
 # 5 kV isolated JTAG/SWD + UART adapter by Unjo AB
 
 adapter driver ftdi
-ftdi_vid_pid 0x22b7 0x150d
+ftdi vid_pid 0x22b7 0x150d
 
-ftdi_layout_init 0x0ff8 0xfffb
+ftdi layout_init 0x0ff8 0xfffb
 
-ftdi_layout_signal LED -ndata 0x0100
-ftdi_layout_signal nTRST -data 0x0200
-ftdi_layout_signal nSRST -noe 0x0400
-ftdi_layout_signal SWDIO_OE -data 0x0008
+ftdi layout_signal LED -ndata 0x0100
+ftdi layout_signal nTRST -data 0x0200
+ftdi layout_signal nSRST -noe 0x0400
+ftdi layout_signal SWDIO_OE -data 0x0008
 
 # Mode signals, either of these needs to be high to drive the JTAG/SWD pins.
 # The power-on state is low for both signals but the init setting above sets
 # JTAG_EN high.
-ftdi_layout_signal SWD_EN -data 0x1000
-ftdi_layout_signal JTAG_EN -data 0x0800
+ftdi layout_signal SWD_EN -data 0x1000
+ftdi layout_signal JTAG_EN -data 0x0800
 
 # In SWD mode, the JTAG_EN signal doubles as SWO_EN_N which switches the
 # second FTDI channel UART RxD to the SWO pin instead of the separate RxD
 # pin. Note that the default init state has this pin high so when OpenOCD
 # starts in SWD mode, SWO is by default disabled. To enable SWO tracing,
-# issue the command 'ftdi_set_signal SWO_EN 1' where tracing is configured.
+# issue the command 'ftdi set_signal SWO_EN 1' where tracing is configured.
 # To switch back to using the separate UART, SWO_EN needs to be disabled
 # before exiting OpenOCD, or the adapter replugged.
-ftdi_layout_signal SWO_EN -nalias JTAG_EN
+ftdi layout_signal SWO_EN -nalias JTAG_EN

diff --git a/tcl/interface/ftdi/jtag-lock-pick_tiny_2.cfg b/tcl/interface/ftdi/jtag-lock-pick_tiny_2.cfg
index 82eeaa7b564301704f358335356634f6dd3aff57..3eefecf8384c7c9552ffa54f1a87fcbe760bbb2b 100644 (file)
--- a/tcl/interface/ftdi/jtag-lock-pick_tiny_2.cfg
+++ b/tcl/interface/ftdi/jtag-lock-pick_tiny_2.cfg
@@ -5,12 +5,12 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "JTAG-lock-pick Tiny 2"
-ftdi_vid_pid 0x0403 0x8220
+ftdi device_desc "JTAG-lock-pick Tiny 2"
+ftdi vid_pid 0x0403 0x8220
 
-ftdi_layout_init 0x8c28 0xff3b
-ftdi_layout_signal SWD_EN -ndata 0x0020 -oe 0x2000
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
-ftdi_layout_signal SWDIO_OE -ndata 0x1000
-ftdi_layout_signal LED -ndata 0x8000
+ftdi layout_init 0x8c28 0xff3b
+ftdi layout_signal SWD_EN -ndata 0x0020 -oe 0x2000
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_signal SWDIO_OE -ndata 0x1000
+ftdi layout_signal LED -ndata 0x8000

diff --git a/tcl/interface/ftdi/jtagkey.cfg b/tcl/interface/ftdi/jtagkey.cfg
index 06463ab91d37ab3368ab78e5156f4582157af02e..511244b3f2124aeed2a98d22fb8c966b33201d1d 100644 (file)
--- a/tcl/interface/ftdi/jtagkey.cfg
+++ b/tcl/interface/ftdi/jtagkey.cfg
@@ -5,9 +5,9 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Amontec JTAGkey"
-ftdi_vid_pid 0x0403 0xcff8
+ftdi device_desc "Amontec JTAGkey"
+ftdi vid_pid 0x0403 0xcff8
 
-ftdi_layout_init 0x0c08 0x0f1b
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_init 0x0c08 0x0f1b
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800

diff --git a/tcl/interface/ftdi/jtagkey2.cfg b/tcl/interface/ftdi/jtagkey2.cfg
index ba151d3b5e7e24b8ae4d1cdf90e85d5e03bf6022..aa33a75289ed21383003246f8df0b4cfddd5c04b 100644 (file)
--- a/tcl/interface/ftdi/jtagkey2.cfg
+++ b/tcl/interface/ftdi/jtagkey2.cfg
@@ -5,9 +5,9 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Amontec JTAGkey-2"
-ftdi_vid_pid 0x0403 0xcff8
+ftdi device_desc "Amontec JTAGkey-2"
+ftdi vid_pid 0x0403 0xcff8
 
-ftdi_layout_init 0x0c08 0x0f1b
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_init 0x0c08 0x0f1b
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800

diff --git a/tcl/interface/ftdi/jtagkey2p.cfg b/tcl/interface/ftdi/jtagkey2p.cfg
index acb5047e9ad7c46c2aff821a7e957d46f31ad7cf..dbfca66c49ab9e3d29fe9e24134074927782818f 100644 (file)
--- a/tcl/interface/ftdi/jtagkey2p.cfg
+++ b/tcl/interface/ftdi/jtagkey2p.cfg
@@ -5,9 +5,9 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Amontec JTAGkey-2P"
-ftdi_vid_pid 0x0403 0xcff8
+ftdi device_desc "Amontec JTAGkey-2P"
+ftdi vid_pid 0x0403 0xcff8
 
-ftdi_layout_init 0x0c08 0x0f1b
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_init 0x0c08 0x0f1b
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800

diff --git a/tcl/interface/ftdi/kt-link.cfg b/tcl/interface/ftdi/kt-link.cfg
index 5fc5db9d0ed959f771839d9a5a258cb51d90baa5..112ecf15494895090dbd666f92b63190a2779634 100644 (file)
--- a/tcl/interface/ftdi/kt-link.cfg
+++ b/tcl/interface/ftdi/kt-link.cfg
@@ -5,12 +5,12 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "KT-LINK"
-ftdi_vid_pid 0x0403 0xbbe2
+ftdi device_desc "KT-LINK"
+ftdi vid_pid 0x0403 0xbbe2
 
-ftdi_layout_init 0x8c28 0xff3b
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
-ftdi_layout_signal LED -data 0x8000
-ftdi_layout_signal SWD_EN -ndata 0x0020 -oe 0x2000
-ftdi_layout_signal SWDIO_OE -ndata 0x1000
+ftdi layout_init 0x8c28 0xff3b
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_signal LED -data 0x8000
+ftdi layout_signal SWD_EN -ndata 0x0020 -oe 0x2000
+ftdi layout_signal SWDIO_OE -ndata 0x1000

diff --git a/tcl/interface/ftdi/lisa-l.cfg b/tcl/interface/ftdi/lisa-l.cfg
index 4e52f7b7eff0f32864daaef58358a52e5b1429f9..3da64a00ed1949fc2b2f83922a61fca551e84474 100644 (file)
--- a/tcl/interface/ftdi/lisa-l.cfg
+++ b/tcl/interface/ftdi/lisa-l.cfg
@@ -10,11 +10,11 @@ echo "in ft2232.c. Please report your experience with this file to openocd-devel
 echo "mailing list, so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "Lisa/L"
-ftdi_vid_pid 0x0403 0x6010
-ftdi_channel 1
+ftdi device_desc "Lisa/L"
+ftdi vid_pid 0x0403 0x6010
+ftdi channel 1
 
-ftdi_layout_init 0x0008 0x180b
-ftdi_layout_signal nTRST -data 0x0010 -oe 0x0010
-ftdi_layout_signal nSRST -data 0x0040 -oe 0x0040
-ftdi_layout_signal LED -data 0x1800
+ftdi layout_init 0x0008 0x180b
+ftdi layout_signal nTRST -data 0x0010 -oe 0x0010
+ftdi layout_signal nSRST -data 0x0040 -oe 0x0040
+ftdi layout_signal LED -data 0x1800

diff --git a/tcl/interface/ftdi/luminary-icdi.cfg b/tcl/interface/ftdi/luminary-icdi.cfg
index 8bc783e92b1e06825281cee89e04068490b437af..08676a3487cf0f3865ab9836b41f761de676099a 100644 (file)
--- a/tcl/interface/ftdi/luminary-icdi.cfg
+++ b/tcl/interface/ftdi/luminary-icdi.cfg
@@ -16,10 +16,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Luminary Micro ICDI Board"
-ftdi_vid_pid 0x0403 0xbcda
+ftdi device_desc "Luminary Micro ICDI Board"
+ftdi vid_pid 0x0403 0xbcda
 
-ftdi_layout_init 0x00a8 0x00eb
-ftdi_layout_signal nSRST -noe 0x0020
-ftdi_layout_signal SWD_EN -ndata 0x0080
-ftdi_layout_signal SWDIO_OE -data 0x0008
+ftdi layout_init 0x00a8 0x00eb
+ftdi layout_signal nSRST -noe 0x0020
+ftdi layout_signal SWD_EN -ndata 0x0080
+ftdi layout_signal SWDIO_OE -data 0x0008

diff --git a/tcl/interface/ftdi/luminary-lm3s811.cfg b/tcl/interface/ftdi/luminary-lm3s811.cfg
index aac915e343c6e36ddcc9e26bb9f4ab424de29cf8..90f454ef08f0bcf20544a3ef0a2c8934bcc9e290 100644 (file)
--- a/tcl/interface/ftdi/luminary-lm3s811.cfg
+++ b/tcl/interface/ftdi/luminary-lm3s811.cfg
@@ -12,10 +12,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "LM3S811 Evaluation Board"
-ftdi_vid_pid 0x0403 0xbcd9
+ftdi device_desc "LM3S811 Evaluation Board"
+ftdi vid_pid 0x0403 0xbcd9
 
-ftdi_layout_init 0x0088 0x008b
-ftdi_layout_signal nSRST -data 0x0020 -oe 0x0020
-ftdi_layout_signal SWD_EN -ndata 0x0080
-ftdi_layout_signal SWDIO_OE -data 0x0008
+ftdi layout_init 0x0088 0x008b
+ftdi layout_signal nSRST -data 0x0020 -oe 0x0020
+ftdi layout_signal SWD_EN -ndata 0x0080
+ftdi layout_signal SWDIO_OE -data 0x0008

diff --git a/tcl/interface/ftdi/luminary.cfg b/tcl/interface/ftdi/luminary.cfg
index 5e34f8cea15ed612f01a5a4f9a9c030a126788d8..3258b214c52a5089c8f24e7d6ab6ade4b27d8206 100644 (file)
--- a/tcl/interface/ftdi/luminary.cfg
+++ b/tcl/interface/ftdi/luminary.cfg
@@ -25,10 +25,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Stellaris Evaluation Board"
-ftdi_vid_pid 0x0403 0xbcd9
+ftdi device_desc "Stellaris Evaluation Board"
+ftdi vid_pid 0x0403 0xbcd9
 
-ftdi_layout_init 0x00a8 0x00eb
-ftdi_layout_signal nSRST -noe 0x0020
-ftdi_layout_signal SWD_EN -ndata 0x0080
-ftdi_layout_signal SWDIO_OE -data 0x0008
+ftdi layout_init 0x00a8 0x00eb
+ftdi layout_signal nSRST -noe 0x0020
+ftdi layout_signal SWD_EN -ndata 0x0080
+ftdi layout_signal SWDIO_OE -data 0x0008

diff --git a/tcl/interface/ftdi/m53evk.cfg b/tcl/interface/ftdi/m53evk.cfg
index 6597f2d3053173137a8845e31fd7c14cd245bc41..2b7c43445a4dd3b03746e6f80d1cdea515555855 100644 (file)
--- a/tcl/interface/ftdi/m53evk.cfg
+++ b/tcl/interface/ftdi/m53evk.cfg
@@ -5,10 +5,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Dual RS232-HS"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Dual RS232-HS"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_channel 0
-ftdi_layout_init 0x0008 0x000b
-ftdi_layout_signal nTRST -data 0x0010 -oe 0x0010
-ftdi_layout_signal nSRST -data 0x0020 -oe 0x0020
+ftdi channel 0
+ftdi layout_init 0x0008 0x000b
+ftdi layout_signal nTRST -data 0x0010 -oe 0x0010
+ftdi layout_signal nSRST -data 0x0020 -oe 0x0020

diff --git a/tcl/interface/ftdi/mbftdi.cfg b/tcl/interface/ftdi/mbftdi.cfg
index c0ff865745f1fe4a7e70d2fd1b6c145b97179b26..a34390ba7cbdf1dfcd47f8bb9edc87e380b7a3eb 100644 (file)
--- a/tcl/interface/ftdi/mbftdi.cfg
+++ b/tcl/interface/ftdi/mbftdi.cfg
@@ -10,7 +10,7 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Dual RS232-HS"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Dual RS232-HS"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0008 0x000b
+ftdi layout_init 0x0008 0x000b

diff --git a/tcl/interface/ftdi/minimodule-swd.cfg b/tcl/interface/ftdi/minimodule-swd.cfg
index 4bc331edb96e40bf723e5b151771f65fc7be6195..15b007afbd2a8c1eb75fcb4e3c3a3e5638a36bd2 100644 (file)
--- a/tcl/interface/ftdi/minimodule-swd.cfg
+++ b/tcl/interface/ftdi/minimodule-swd.cfg
@@ -38,17 +38,17 @@ adapter driver ftdi
 
 #Select your module type and channel
 
-#ftdi_device_desc "FT2232H MiniModule"
-ftdi_vid_pid 0x0403 0x6010
-#ftdi_channel 1
+#ftdi device_desc "FT2232H MiniModule"
+ftdi vid_pid 0x0403 0x6010
+#ftdi channel 1
 
-#ftdi_device_desc "FT4232H MiniModule"
-#ftdi_vid_pid 0x0403 0x6011
-#ftdi_channel 1
+#ftdi device_desc "FT4232H MiniModule"
+#ftdi vid_pid 0x0403 0x6011
+#ftdi channel 1
 
-ftdi_layout_init 0x0000 0x000b
-ftdi_layout_signal nSRST -data 0x0010 -oe 0x0010
-ftdi_layout_signal SWD_EN -data 0
-ftdi_layout_signal SWDIO_OE -data 0
+ftdi layout_init 0x0000 0x000b
+ftdi layout_signal nSRST -data 0x0010 -oe 0x0010
+ftdi layout_signal SWD_EN -data 0
+ftdi layout_signal SWDIO_OE -data 0
 
 transport select swd

diff --git a/tcl/interface/ftdi/minimodule.cfg b/tcl/interface/ftdi/minimodule.cfg
index 5dcce1fcf96302e61977cc42472df11784dbf46a..6b2d60c07c1b29e1114f9e4d11a2fb3f6447230f 100644 (file)
--- a/tcl/interface/ftdi/minimodule.cfg
+++ b/tcl/interface/ftdi/minimodule.cfg
@@ -5,12 +5,12 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "FT2232H MiniModule"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "FT2232H MiniModule"
+ftdi vid_pid 0x0403 0x6010
 
 # Every pin set as high impedance except TCK, TDI, TDO and TMS
-ftdi_layout_init 0x0008 0x000b
+ftdi layout_init 0x0008 0x000b
 
 # nSRST defined on pin CN2-13 of the MiniModule (pin ADBUS5 [AD5] on the FT2232H chip)
 # This choice is arbitrary. Use other GPIO pin if desired.
-ftdi_layout_signal nSRST -data 0x0020 -oe 0x0020
+ftdi layout_signal nSRST -data 0x0020 -oe 0x0020

diff --git a/tcl/interface/ftdi/minispartan6.cfg b/tcl/interface/ftdi/minispartan6.cfg
index 97a6abe04aa3697d0a61e2369554ac697815ebd9..faf820d7af54ff88416ca9dc96b5d8aa68efdd00 100644 (file)
--- a/tcl/interface/ftdi/minispartan6.cfg
+++ b/tcl/interface/ftdi/minispartan6.cfg
@@ -3,12 +3,12 @@
 adapter driver ftdi
 # The miniSpartan6+ sadly doesn't have a custom device description, so we just
 # have to hope you got it right.
-#ftdi_device_desc "Dual RS232-HS"
-ftdi_vid_pid 0x0403 0x6010
+#ftdi device_desc "Dual RS232-HS"
+ftdi vid_pid 0x0403 0x6010
 # interface 1 is the uart
-ftdi_channel 0
+ftdi channel 0
 # just TCK TDI TDO TMS, no reset
-ftdi_layout_init 0x0008 0x000b
+ftdi layout_init 0x0008 0x000b
 reset_config none
 # this generally works fast: the fpga can handle 30MHz, the spi flash can handle
 # 54MHz with simple read, no dummy cycles, and wait-for-write-completion

diff --git a/tcl/interface/ftdi/miniwiggler.cfg b/tcl/interface/ftdi/miniwiggler.cfg
index 6e53daede8bcfcc85fa3719bb1c70606bc86a495..ebaa97920b11ab817041785fd35b2841d11ca511 100644 (file)
--- a/tcl/interface/ftdi/miniwiggler.cfg
+++ b/tcl/interface/ftdi/miniwiggler.cfg
@@ -25,10 +25,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "DAS JDS miniWiggler V3.1"
-ftdi_vid_pid 0x058b 0x0043
+ftdi device_desc "DAS JDS miniWiggler V3.1"
+ftdi vid_pid 0x058b 0x0043
 
-ftdi_channel 0
-ftdi_layout_init 0x0008 0x001b
-ftdi_layout_signal nTRST -data 0x0100 -oe 0x0100
-ftdi_layout_signal nSRST -data 0x0200 -oe 0x0200
+ftdi channel 0
+ftdi layout_init 0x0008 0x001b
+ftdi layout_signal nTRST -data 0x0100 -oe 0x0100
+ftdi layout_signal nSRST -data 0x0200 -oe 0x0200

diff --git a/tcl/interface/ftdi/neodb.cfg b/tcl/interface/ftdi/neodb.cfg
index 1cfb3526ca6730e2148dd4885cabac1aefe56bde..426f5c4c7ee18b9e0927b098c871543544d28190 100644 (file)
--- a/tcl/interface/ftdi/neodb.cfg
+++ b/tcl/interface/ftdi/neodb.cfg
@@ -5,10 +5,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Debug Board for Neo1973"
-ftdi_vid_pid 0x1457 0x5118
+ftdi device_desc "Debug Board for Neo1973"
+ftdi vid_pid 0x1457 0x5118
 
-ftdi_layout_init 0x0508 0x0f1b
-ftdi_layout_signal nTRST -data 0x0200 -noe 0x0100
-ftdi_layout_signal nSRST -data 0x0800 -noe 0x0400
-ftdi_layout_signal nNOR_WP -data 0x0010 -oe 0x0010
+ftdi layout_init 0x0508 0x0f1b
+ftdi layout_signal nTRST -data 0x0200 -noe 0x0100
+ftdi layout_signal nSRST -data 0x0800 -noe 0x0400
+ftdi layout_signal nNOR_WP -data 0x0010 -oe 0x0010

diff --git a/tcl/interface/ftdi/ngxtech.cfg b/tcl/interface/ftdi/ngxtech.cfg
index 3aa79ab310729ab235be692c966a53e9f4d09bf0..962f25baae7bc61319f4d3472a74936408ad4ab3 100644 (file)
--- a/tcl/interface/ftdi/ngxtech.cfg
+++ b/tcl/interface/ftdi/ngxtech.cfg
@@ -11,9 +11,9 @@ echo "experience with this file to openocd-devel mailing list, so it could be ma
 echo "as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "NGX JTAG"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "NGX JTAG"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0508 0x0f1b
-ftdi_layout_signal nTRST -data 0x0200 -noe 0x0100
-ftdi_layout_signal nSRST -data 0x0800 -noe 0x0400
+ftdi layout_init 0x0508 0x0f1b
+ftdi layout_signal nTRST -data 0x0200 -noe 0x0100
+ftdi layout_signal nSRST -data 0x0800 -noe 0x0400

diff --git a/tcl/interface/ftdi/olimex-arm-jtag-swd.cfg b/tcl/interface/ftdi/olimex-arm-jtag-swd.cfg
index 2153fd65f59c83f84bdfc7d23191819f0e0f3864..ace0df98d8316c6e890fe5070faa9b4c89f51048 100644 (file)
--- a/tcl/interface/ftdi/olimex-arm-jtag-swd.cfg
+++ b/tcl/interface/ftdi/olimex-arm-jtag-swd.cfg
@@ -5,5 +5,5 @@
 
 transport select swd
 
-ftdi_layout_signal SWD_EN -nalias nTRST
-ftdi_layout_signal SWDIO_OE -alias TMS
+ftdi layout_signal SWD_EN -nalias nTRST
+ftdi layout_signal SWDIO_OE -alias TMS

diff --git a/tcl/interface/ftdi/olimex-arm-usb-ocd-h.cfg b/tcl/interface/ftdi/olimex-arm-usb-ocd-h.cfg
index c8e3befb7d40a582671cc5444fc6c28edabb43dd..ca014a4d47e8992e63b89911d48fa3c87131501d 100644 (file)
--- a/tcl/interface/ftdi/olimex-arm-usb-ocd-h.cfg
+++ b/tcl/interface/ftdi/olimex-arm-usb-ocd-h.cfg
@@ -5,10 +5,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Olimex OpenOCD JTAG ARM-USB-OCD-H"
-ftdi_vid_pid 0x15ba 0x002b
+ftdi device_desc "Olimex OpenOCD JTAG ARM-USB-OCD-H"
+ftdi vid_pid 0x15ba 0x002b
 
-ftdi_layout_init 0x0908 0x0b1b
-ftdi_layout_signal nSRST -oe 0x0200
-ftdi_layout_signal nTRST -data 0x0100
-ftdi_layout_signal LED -data 0x0800
+ftdi layout_init 0x0908 0x0b1b
+ftdi layout_signal nSRST -oe 0x0200
+ftdi layout_signal nTRST -data 0x0100
+ftdi layout_signal LED -data 0x0800

diff --git a/tcl/interface/ftdi/olimex-arm-usb-ocd.cfg b/tcl/interface/ftdi/olimex-arm-usb-ocd.cfg
index f9126d40d22e3e4c43521ce63382dc5358e27b06..6b925758313663bbe9de4b2ddeb6b14b6a115760 100644 (file)
--- a/tcl/interface/ftdi/olimex-arm-usb-ocd.cfg
+++ b/tcl/interface/ftdi/olimex-arm-usb-ocd.cfg
@@ -5,10 +5,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Olimex OpenOCD JTAG"
-ftdi_vid_pid 0x15ba 0x0003
+ftdi device_desc "Olimex OpenOCD JTAG"
+ftdi vid_pid 0x15ba 0x0003
 
-ftdi_layout_init 0x0c08 0x0f1b
-ftdi_layout_signal nSRST -oe 0x0200
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal LED -data 0x0800
+ftdi layout_init 0x0c08 0x0f1b
+ftdi layout_signal nSRST -oe 0x0200
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal LED -data 0x0800

diff --git a/tcl/interface/ftdi/olimex-arm-usb-tiny-h.cfg b/tcl/interface/ftdi/olimex-arm-usb-tiny-h.cfg
index eac25b6da795c811ed07ccc759d0fa40b7251ce1..98fe367847dd991ced05b4c03863977b283f4a2e 100644 (file)
--- a/tcl/interface/ftdi/olimex-arm-usb-tiny-h.cfg
+++ b/tcl/interface/ftdi/olimex-arm-usb-tiny-h.cfg
@@ -5,10 +5,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Olimex OpenOCD JTAG ARM-USB-TINY-H"
-ftdi_vid_pid 0x15ba 0x002a
+ftdi device_desc "Olimex OpenOCD JTAG ARM-USB-TINY-H"
+ftdi vid_pid 0x15ba 0x002a
 
-ftdi_layout_init 0x0808 0x0a1b
-ftdi_layout_signal nSRST -oe 0x0200
-ftdi_layout_signal nTRST -data 0x0100 -oe 0x0100
-ftdi_layout_signal LED -data 0x0800
+ftdi layout_init 0x0808 0x0a1b
+ftdi layout_signal nSRST -oe 0x0200
+ftdi layout_signal nTRST -data 0x0100 -oe 0x0100
+ftdi layout_signal LED -data 0x0800

diff --git a/tcl/interface/ftdi/olimex-jtag-tiny.cfg b/tcl/interface/ftdi/olimex-jtag-tiny.cfg
index 4811f4dda0eae8daa5651f2bad9921f8d3ec8afa..ebca496d2fe7fad9e87db27fc7acfb6546f61221 100644 (file)
--- a/tcl/interface/ftdi/olimex-jtag-tiny.cfg
+++ b/tcl/interface/ftdi/olimex-jtag-tiny.cfg
@@ -5,10 +5,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Olimex OpenOCD JTAG TINY"
-ftdi_vid_pid 0x15ba 0x0004
+ftdi device_desc "Olimex OpenOCD JTAG TINY"
+ftdi vid_pid 0x15ba 0x0004
 
-ftdi_layout_init 0x0808 0x0a1b
-ftdi_layout_signal nSRST -oe 0x0200
-ftdi_layout_signal nTRST -data 0x0100 -oe 0x0100
-ftdi_layout_signal LED -data 0x0800
+ftdi layout_init 0x0808 0x0a1b
+ftdi layout_signal nSRST -oe 0x0200
+ftdi layout_signal nTRST -data 0x0100 -oe 0x0100
+ftdi layout_signal LED -data 0x0800

diff --git a/tcl/interface/ftdi/oocdlink.cfg b/tcl/interface/ftdi/oocdlink.cfg
index deba4a504e8595b14390f9590c0db83bddc34484..367112a6cb01fa670c0a68da1abc068b90b14f12 100644 (file)
--- a/tcl/interface/ftdi/oocdlink.cfg
+++ b/tcl/interface/ftdi/oocdlink.cfg
@@ -11,9 +11,9 @@ echo "experience with this file to openocd-devel mailing list, so it could be ma
 echo "as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "OOCDLink"
-ftdi_vid_pid 0x0403 0xbaf8
+ftdi device_desc "OOCDLink"
+ftdi vid_pid 0x0403 0xbaf8
 
-ftdi_layout_init 0x0508 0x0f1b
-ftdi_layout_signal nTRST -data 0x0200 -noe 0x0100
-ftdi_layout_signal nSRST -data 0x0800 -noe 0x0400
+ftdi layout_init 0x0508 0x0f1b
+ftdi layout_signal nTRST -data 0x0200 -noe 0x0100
+ftdi layout_signal nSRST -data 0x0800 -noe 0x0400

diff --git a/tcl/interface/ftdi/opendous_ftdi.cfg b/tcl/interface/ftdi/opendous_ftdi.cfg
index 50f32fb3a2cf3adea47879fe5dee1825e39b9919..f212bf561b36af30850c69f5cedb4d78814fe715 100644 (file)
--- a/tcl/interface/ftdi/opendous_ftdi.cfg
+++ b/tcl/interface/ftdi/opendous_ftdi.cfg
@@ -8,10 +8,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Dual RS232-HS"
-ftdi_vid_pid 0x0403 0x6010
-ftdi_channel 1
+ftdi device_desc "Dual RS232-HS"
+ftdi vid_pid 0x0403 0x6010
+ftdi channel 1
 
-ftdi_layout_init 0x0c08 0x0f1b
-ftdi_layout_signal nTRST -data 0x0100 -noe 0x0400
-ftdi_layout_signal nSRST -data 0x0200 -noe 0x0800
+ftdi layout_init 0x0c08 0x0f1b
+ftdi layout_signal nTRST -data 0x0100 -noe 0x0400
+ftdi layout_signal nSRST -data 0x0200 -noe 0x0800

diff --git a/tcl/interface/ftdi/openocd-usb-hs.cfg b/tcl/interface/ftdi/openocd-usb-hs.cfg
index 6f67689f61c6c573b80d1821449c5d1331e51aa3..d1a3ff0a28991119d0a7f9f823cc22621cacb33c 100644 (file)
--- a/tcl/interface/ftdi/openocd-usb-hs.cfg
+++ b/tcl/interface/ftdi/openocd-usb-hs.cfg
@@ -5,9 +5,9 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Dual RS232-HS"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Dual RS232-HS"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0508 0x0f1b
-ftdi_layout_signal nTRST -data 0x0200 -noe 0x0100
-ftdi_layout_signal nSRST -data 0x0800 -noe 0x0400
+ftdi layout_init 0x0508 0x0f1b
+ftdi layout_signal nTRST -data 0x0200 -noe 0x0100
+ftdi layout_signal nSRST -data 0x0800 -noe 0x0400

diff --git a/tcl/interface/ftdi/openocd-usb.cfg b/tcl/interface/ftdi/openocd-usb.cfg
index ed80a05d90149fb4f617b2bdbf981ddb26b8accf..620d2043694351ef01903c9c4388502c2905cf6a 100644 (file)
--- a/tcl/interface/ftdi/openocd-usb.cfg
+++ b/tcl/interface/ftdi/openocd-usb.cfg
@@ -5,9 +5,9 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Dual RS232"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Dual RS232"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0508 0x0f1b
-ftdi_layout_signal nTRST -data 0x0200 -noe 0x0100
-ftdi_layout_signal nSRST -data 0x0800 -noe 0x0400
+ftdi layout_init 0x0508 0x0f1b
+ftdi layout_signal nTRST -data 0x0200 -noe 0x0100
+ftdi layout_signal nSRST -data 0x0800 -noe 0x0400

diff --git a/tcl/interface/ftdi/openrd.cfg b/tcl/interface/ftdi/openrd.cfg
index 535c5e896f42c968e7f4773fbf8d9de5664d1a4e..88b2a6e511885936326935abee8b186ddd595a46 100644 (file)
--- a/tcl/interface/ftdi/openrd.cfg
+++ b/tcl/interface/ftdi/openrd.cfg
@@ -5,10 +5,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "OpenRD JTAGKey FT2232D B"
-ftdi_vid_pid 0x0403 0x9e90
-ftdi_channel 0
+ftdi device_desc "OpenRD JTAGKey FT2232D B"
+ftdi vid_pid 0x0403 0x9e90
+ftdi channel 0
 
-ftdi_layout_init 0x0608 0x0f1b
-ftdi_layout_signal nTRST -data 0x0200
-ftdi_layout_signal nSRST -noe 0x0400
+ftdi layout_init 0x0608 0x0f1b
+ftdi layout_signal nTRST -data 0x0200
+ftdi layout_signal nSRST -noe 0x0400

diff --git a/tcl/interface/ftdi/pipistrello.cfg b/tcl/interface/ftdi/pipistrello.cfg
index 2074924a3f9298302d06cf80d53c5cc750567849..11fcf077cfd35288accd5b55db9f756b19d67619 100644 (file)
--- a/tcl/interface/ftdi/pipistrello.cfg
+++ b/tcl/interface/ftdi/pipistrello.cfg
@@ -1,12 +1,12 @@
 # http://pipistrello.saanlima.com/
 # http://www.saanlima.com/download/pipistrello-v2.0/pipistrello_v2_schematic.pdf
 adapter driver ftdi
-ftdi_device_desc "Pipistrello LX45"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "Pipistrello LX45"
+ftdi vid_pid 0x0403 0x6010
 # interface 1 is the uart
-ftdi_channel 0
+ftdi channel 0
 # just TCK TDI TDO TMS, no reset
-ftdi_layout_init 0x0008 0x000b
+ftdi layout_init 0x0008 0x000b
 reset_config none
 # this generally works fast: the fpga can handle 30MHz, the spi flash can handle
 # 54MHz with simple read, no dummy cycles, and wait-for-write-completion

diff --git a/tcl/interface/ftdi/pls_spc5.cfg b/tcl/interface/ftdi/pls_spc5.cfg
index 806f920fe5982b5f85233f9d783cbbf421cd4cad..3b3c2d6475b3a9173ee82601460f74cf8ad91f1b 100644 (file)
--- a/tcl/interface/ftdi/pls_spc5.cfg
+++ b/tcl/interface/ftdi/pls_spc5.cfg
@@ -27,10 +27,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "PLS USB/JTAG Adapter for SPC5xxx"
-ftdi_vid_pid 0x263d 0x4001
+ftdi device_desc "PLS USB/JTAG Adapter for SPC5xxx"
+ftdi vid_pid 0x263d 0x4001
 
-ftdi_channel 0
-ftdi_layout_init 0x0008 0x000b
-ftdi_layout_signal nTRST -data 0x0100 -oe 0x0100
-ftdi_layout_signal nSRST -ndata 0x2000 -oe 0x2000
+ftdi channel 0
+ftdi layout_init 0x0008 0x000b
+ftdi layout_signal nTRST -data 0x0100 -oe 0x0100
+ftdi layout_signal nSRST -ndata 0x2000 -oe 0x2000

diff --git a/tcl/interface/ftdi/redbee-econotag.cfg b/tcl/interface/ftdi/redbee-econotag.cfg
index b6f6d23bad5116321adc0d6ba69f82a029f1716b..35bedfa7e680b0c5b94ed6dfa4a65f9e068d1da0 100644 (file)
--- a/tcl/interface/ftdi/redbee-econotag.cfg
+++ b/tcl/interface/ftdi/redbee-econotag.cfg
@@ -14,8 +14,8 @@ echo "Please report your experience with this file to openocd-devel mailing list
 echo "so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6010
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0c08 0x0c2b
-ftdi_layout_signal nTRST -data 0x0800
-ftdi_layout_signal nSRST -data 0x0400
+ftdi layout_init 0x0c08 0x0c2b
+ftdi layout_signal nTRST -data 0x0800
+ftdi layout_signal nSRST -data 0x0400

diff --git a/tcl/interface/ftdi/redbee-usb.cfg b/tcl/interface/ftdi/redbee-usb.cfg
index 52ab93e025e98a9861f28d3e423368dc4b873ebd..a57176610961185e0395aecd273bec864373ae8a 100644 (file)
--- a/tcl/interface/ftdi/redbee-usb.cfg
+++ b/tcl/interface/ftdi/redbee-usb.cfg
@@ -14,9 +14,9 @@ echo "Please report your experience with this file to openocd-devel mailing list
 echo "so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6010
-ftdi_channel 1
+ftdi vid_pid 0x0403 0x6010
+ftdi channel 1
 
-ftdi_layout_init 0x0c08 0x0c2b
-ftdi_layout_signal nTRST -data 0x0800
-ftdi_layout_signal nSRST -data 0x0400
+ftdi layout_init 0x0c08 0x0c2b
+ftdi layout_signal nTRST -data 0x0800
+ftdi layout_signal nSRST -data 0x0400

diff --git a/tcl/interface/ftdi/rowley-cc-arm-swd.cfg b/tcl/interface/ftdi/rowley-cc-arm-swd.cfg
index 9a96dbd9250e2b1551c1a1b8f0e15e32b042c33b..fb416db566d8213dcc2b538f3978556f00f262e0 100644 (file)
--- a/tcl/interface/ftdi/rowley-cc-arm-swd.cfg
+++ b/tcl/interface/ftdi/rowley-cc-arm-swd.cfg
@@ -6,5 +6,5 @@
 
 transport select swd
 
-ftdi_layout_signal SWD_EN -nalias nTRST
-ftdi_layout_signal SWDIO_OE -alias TMS
+ftdi layout_signal SWD_EN -nalias nTRST
+ftdi layout_signal SWDIO_OE -alias TMS

diff --git a/tcl/interface/ftdi/sheevaplug.cfg b/tcl/interface/ftdi/sheevaplug.cfg
index e582350326831c43c73c8f7f8a06d48716a74286..5929453c17406915f90461e47c0d60686382a222 100644 (file)
--- a/tcl/interface/ftdi/sheevaplug.cfg
+++ b/tcl/interface/ftdi/sheevaplug.cfg
@@ -5,10 +5,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "SheevaPlug JTAGKey FT2232D B"
-ftdi_vid_pid 0x9e88 0x9e8f
-ftdi_channel 0
+ftdi device_desc "SheevaPlug JTAGKey FT2232D B"
+ftdi vid_pid 0x9e88 0x9e8f
+ftdi channel 0
 
-ftdi_layout_init 0x0608 0x0f1b
-ftdi_layout_signal nTRST -data 0x0200 -noe 0x0100
-ftdi_layout_signal nSRST -data 0x0800 -noe 0x0400
+ftdi layout_init 0x0608 0x0f1b
+ftdi layout_signal nTRST -data 0x0200 -noe 0x0100
+ftdi layout_signal nSRST -data 0x0800 -noe 0x0400

diff --git a/tcl/interface/ftdi/signalyzer-lite.cfg b/tcl/interface/ftdi/signalyzer-lite.cfg
index 4778420058f156531c7d94f56749ce2862b41249..9e010d3944eb24ec816553ed5cce14401141f458 100644 (file)
--- a/tcl/interface/ftdi/signalyzer-lite.cfg
+++ b/tcl/interface/ftdi/signalyzer-lite.cfg
@@ -10,9 +10,9 @@ echo "Please report your experience with this file to openocd-devel mailing list
 echo "so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "Signalyzer LITE"
-ftdi_vid_pid 0x0403 0xbca1
+ftdi device_desc "Signalyzer LITE"
+ftdi vid_pid 0x0403 0xbca1
 
-ftdi_layout_init 0x0008 0x000b
-ftdi_layout_signal nTRST -data 0x0010 -oe 0x0010
-ftdi_layout_signal nSRST -data 0x0020 -oe 0x0020
+ftdi layout_init 0x0008 0x000b
+ftdi layout_signal nTRST -data 0x0010 -oe 0x0010
+ftdi layout_signal nSRST -data 0x0020 -oe 0x0020

diff --git a/tcl/interface/ftdi/signalyzer.cfg b/tcl/interface/ftdi/signalyzer.cfg
index 2439298352e2158e215f067d652dd0be5dbdc2c5..d94c6bc7fa7a65875a5118735e492f5d36d03b12 100644 (file)
--- a/tcl/interface/ftdi/signalyzer.cfg
+++ b/tcl/interface/ftdi/signalyzer.cfg
@@ -10,9 +10,9 @@ echo "Please report your experience with this file to openocd-devel mailing list
 echo "so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "Signalyzer"
-ftdi_vid_pid 0x0403 0xbca0
+ftdi device_desc "Signalyzer"
+ftdi vid_pid 0x0403 0xbca0
 
-ftdi_layout_init 0x0008 0x000b
-ftdi_layout_signal nTRST -data 0x0010 -oe 0x0010
-ftdi_layout_signal nSRST -data 0x0020 -oe 0x0020
+ftdi layout_init 0x0008 0x000b
+ftdi layout_signal nTRST -data 0x0010 -oe 0x0010
+ftdi layout_signal nSRST -data 0x0020 -oe 0x0020

diff --git a/tcl/interface/ftdi/snps_sdp.cfg b/tcl/interface/ftdi/snps_sdp.cfg
index 3aed2ae20a32995995a53c706cece01344d38a70..7bd8387b7b2a1b937a1597748f2b0faa83e6b85d 100644 (file)
--- a/tcl/interface/ftdi/snps_sdp.cfg
+++ b/tcl/interface/ftdi/snps_sdp.cfg
@@ -11,8 +11,8 @@
 #
 
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6010
-ftdi_layout_init 0x0088 0x008b
-ftdi_channel 1
+ftdi vid_pid 0x0403 0x6010
+ftdi layout_init 0x0088 0x008b
+ftdi channel 1
 
 

diff --git a/tcl/interface/ftdi/steppenprobe.cfg b/tcl/interface/ftdi/steppenprobe.cfg
index 7b5b9a0347db33c02d5d2ede440436e6ad10eecd..f84efe61edf4ed3c9c1d06e0de5d77c821eb4cc8 100644 (file)
--- a/tcl/interface/ftdi/steppenprobe.cfg
+++ b/tcl/interface/ftdi/steppenprobe.cfg
@@ -6,10 +6,10 @@
 #
 
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x6010
+ftdi vid_pid 0x0403 0x6010
 
 # Initial Layout
-ftdi_layout_init 0x0058 0x99fb
+ftdi layout_init 0x0058 0x99fb
 # Signal        Data    Direction       Notes
 # TCK           0       1 (out)
 # TDI           0       1 (out)
@@ -30,12 +30,12 @@ ftdi_layout_init 0x0058 0x99fb
 # Unused        0       1 (out)
 
 # Signals definition
-ftdi_layout_signal LED -ndata 0x0010
-ftdi_layout_signal SWD_EN -data 0x0020
-ftdi_layout_signal SWDIO_OE -ndata 0x0040
-ftdi_layout_signal nSRST -oe 0x0080
+ftdi layout_signal LED -ndata 0x0010
+ftdi layout_signal SWD_EN -data 0x0020
+ftdi layout_signal SWDIO_OE -ndata 0x0040
+ftdi layout_signal nSRST -oe 0x0080
 
-ftdi_layout_signal GPIO_A -data 0x0200 -oe 0x0200 -input 0x0200
-ftdi_layout_signal GPIO_B -data 0x0400 -oe 0x0400 -input 0x0400
-ftdi_layout_signal GPIO_C -data 0x2000 -oe 0x2000 -input 0x2000
-ftdi_layout_signal GPIO_D -data 0x4000 -oe 0x4000 -input 0x4000
+ftdi layout_signal GPIO_A -data 0x0200 -oe 0x0200 -input 0x0200
+ftdi layout_signal GPIO_B -data 0x0400 -oe 0x0400 -input 0x0400
+ftdi layout_signal GPIO_C -data 0x2000 -oe 0x2000 -input 0x2000
+ftdi layout_signal GPIO_D -data 0x4000 -oe 0x4000 -input 0x4000

diff --git a/tcl/interface/ftdi/stm32-stick.cfg b/tcl/interface/ftdi/stm32-stick.cfg
index 7ae02bd8009df8f4f945e131633db6d73d5f806d..fd877ec77cfd0ae038d0f95f88a4294bf07f3707 100644 (file)
--- a/tcl/interface/ftdi/stm32-stick.cfg
+++ b/tcl/interface/ftdi/stm32-stick.cfg
@@ -5,9 +5,9 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "STM32-PerformanceStick"
-ftdi_vid_pid 0x0640 0x002d
+ftdi device_desc "STM32-PerformanceStick"
+ftdi vid_pid 0x0640 0x002d
 
-ftdi_layout_init 0x0388 0x038b
-ftdi_layout_signal nTRST -data 0x0100
-ftdi_layout_signal nSRST -data 0x0080 -noe 0x200
+ftdi layout_init 0x0388 0x038b
+ftdi layout_signal nTRST -data 0x0100
+ftdi layout_signal nSRST -data 0x0080 -noe 0x200

diff --git a/tcl/interface/ftdi/swd-resistor-hack.cfg b/tcl/interface/ftdi/swd-resistor-hack.cfg
index 26eb44c5f659c9feb40d8cb423e2c5d27735272d..5bdb87c18cb83ac383dfc7ffc16c4dabd64e6263 100644 (file)
--- a/tcl/interface/ftdi/swd-resistor-hack.cfg
+++ b/tcl/interface/ftdi/swd-resistor-hack.cfg
@@ -23,4 +23,4 @@
 
 transport select swd
 
-ftdi_layout_signal SWD_EN -data 0
+ftdi layout_signal SWD_EN -data 0

diff --git a/tcl/interface/ftdi/ti-icdi.cfg b/tcl/interface/ftdi/ti-icdi.cfg
index 55085eaee04f0f0ecfbc4891a7248873a42b4173..f6e16be846be6c238144ca3d52efb6f9522d49ff 100644 (file)
--- a/tcl/interface/ftdi/ti-icdi.cfg
+++ b/tcl/interface/ftdi/ti-icdi.cfg
@@ -7,9 +7,9 @@
 #
 
 adapter driver ftdi
-ftdi_vid_pid 0x0451 0xc32a
+ftdi vid_pid 0x0451 0xc32a
 
-ftdi_layout_init 0x00a8 0x00eb
-ftdi_layout_signal nSRST -noe 0x0020
-ftdi_layout_signal SWD_EN -ndata 0x0080
-ftdi_layout_signal SWDIO_OE -data 0x0008
+ftdi layout_init 0x00a8 0x00eb
+ftdi layout_signal nSRST -noe 0x0020
+ftdi layout_signal SWD_EN -ndata 0x0080
+ftdi layout_signal SWDIO_OE -data 0x0008

diff --git a/tcl/interface/ftdi/tumpa-lite.cfg b/tcl/interface/ftdi/tumpa-lite.cfg
index 7f576e91d2f17f22591749a2085d8f965eceda0d..625db16b120acf1448f45a6013df919007411cb1 100644 (file)
--- a/tcl/interface/ftdi/tumpa-lite.cfg
+++ b/tcl/interface/ftdi/tumpa-lite.cfg
@@ -5,8 +5,8 @@
 #
 
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x8a99
+ftdi vid_pid 0x0403 0x8a99
 
-ftdi_layout_init 0x0038 0x087b
-ftdi_layout_signal nTRST -data 0x0020 -oe 0x0020
-ftdi_layout_signal nSRST -data 0x0010 -oe 0x0010
+ftdi layout_init 0x0038 0x087b
+ftdi layout_signal nTRST -data 0x0020 -oe 0x0020
+ftdi layout_signal nSRST -data 0x0010 -oe 0x0010

diff --git a/tcl/interface/ftdi/tumpa.cfg b/tcl/interface/ftdi/tumpa.cfg
index 1a4e3cdfa33a66eab9a6b8579a81815893e09014..4491c40b73a6b1f079901b8899c4916c8204d8df 100644 (file)
--- a/tcl/interface/ftdi/tumpa.cfg
+++ b/tcl/interface/ftdi/tumpa.cfg
@@ -5,10 +5,10 @@
 #
 
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0x8a98 0x0403 0x6010
+ftdi vid_pid 0x0403 0x8a98 0x0403 0x6010
 
-ftdi_layout_init 0x0038 0x087b
-ftdi_layout_signal nTRST -data 0x0020
-ftdi_layout_signal nSRST -data 0x0010
+ftdi layout_init 0x0038 0x087b
+ftdi layout_signal nTRST -data 0x0020
+ftdi layout_signal nSRST -data 0x0010
 
 reset_config srst_push_pull

diff --git a/tcl/interface/ftdi/turtelizer2-revB.cfg b/tcl/interface/ftdi/turtelizer2-revB.cfg
index 34ae8612986c089a83e9a8b332b86ce59174c109..593a545a8c82029da2daddae5223c502475528f3 100644 (file)
--- a/tcl/interface/ftdi/turtelizer2-revB.cfg
+++ b/tcl/interface/ftdi/turtelizer2-revB.cfg
@@ -10,9 +10,9 @@ echo "in ft2232.c. Please report your experience with this file to openocd-devel
 echo "mailing list, so it could be marked as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "Turtelizer JTAG/RS232 Adapter"
-ftdi_vid_pid 0x0403 0xbdc8
+ftdi device_desc "Turtelizer JTAG/RS232 Adapter"
+ftdi vid_pid 0x0403 0xbdc8
 
-ftdi_layout_init 0x0008 0x0c5b
-ftdi_layout_signal nSRST -oe 0x0040
-ftdi_layout_signal LED -data 0x0c00
+ftdi layout_init 0x0008 0x0c5b
+ftdi layout_signal nSRST -oe 0x0040
+ftdi layout_signal LED -data 0x0c00

diff --git a/tcl/interface/ftdi/turtelizer2-revC.cfg b/tcl/interface/ftdi/turtelizer2-revC.cfg
index f5192fb31059c48d244c1fef7b2528932db3a7f5..6e19259b99ba0b42ffee57e3f1cfc71a7ec05102 100644 (file)
--- a/tcl/interface/ftdi/turtelizer2-revC.cfg
+++ b/tcl/interface/ftdi/turtelizer2-revC.cfg
@@ -5,10 +5,10 @@
 #
 
 adapter driver ftdi
-ftdi_device_desc "Turtelizer JTAG/RS232 Adapter"
-ftdi_vid_pid 0x0403 0xbdc8
+ftdi device_desc "Turtelizer JTAG/RS232 Adapter"
+ftdi vid_pid 0x0403 0xbdc8
 
-ftdi_layout_init 0x0008 0x0c7b
-ftdi_layout_signal nTRST -oe 0x0020
-ftdi_layout_signal nSRST -oe 0x0040
-ftdi_layout_signal LED -ndata 0x0c00
+ftdi layout_init 0x0008 0x0c7b
+ftdi layout_signal nTRST -oe 0x0020
+ftdi layout_signal nSRST -oe 0x0040
+ftdi layout_signal LED -ndata 0x0c00

diff --git a/tcl/interface/ftdi/um232h.cfg b/tcl/interface/ftdi/um232h.cfg
index 2dabbec4a6b7ebd0dd8d91ac5deadd8e4d50d80d..10f267dd0cfb8f70dae4b068a8ea9876c18f1aed 100644 (file)
--- a/tcl/interface/ftdi/um232h.cfg
+++ b/tcl/interface/ftdi/um232h.cfg
@@ -8,12 +8,12 @@
 #
 
 adapter driver ftdi
-#ftdi_device_desc "UM232H"
-ftdi_vid_pid 0x0403 0x6014
+#ftdi device_desc "UM232H"
+ftdi vid_pid 0x0403 0x6014
 
-ftdi_layout_init 0xfff8 0xfffb
-ftdi_layout_signal nTRST -data 0x0100 -oe 0x0100
-ftdi_layout_signal nSRST -data 0x0200 -oe 0x0200
+ftdi layout_init 0xfff8 0xfffb
+ftdi layout_signal nTRST -data 0x0100 -oe 0x0100
+ftdi layout_signal nSRST -data 0x0200 -oe 0x0200
 
 # UM232H        FT232H    JTAG
 # Name  Pin     Name      Func

diff --git a/tcl/interface/ftdi/vpaclink.cfg b/tcl/interface/ftdi/vpaclink.cfg
index ed4895a6bd7075380a54d072517d75f62b04df61..7e7f25702cf5d64768df6dd82158fc6bac42329c 100644 (file)
--- a/tcl/interface/ftdi/vpaclink.cfg
+++ b/tcl/interface/ftdi/vpaclink.cfg
@@ -11,9 +11,9 @@ echo "experience with this file to openocd-devel mailing list, so it could be ma
 echo "as working or fixed."
 
 adapter driver ftdi
-ftdi_device_desc "VPACLink"
-ftdi_vid_pid 0x0403 0x6010
+ftdi device_desc "VPACLink"
+ftdi vid_pid 0x0403 0x6010
 
-ftdi_layout_init 0x0508 0x0f1b
-ftdi_layout_signal nTRST -data 0x0200 -noe 0x0100
-ftdi_layout_signal nSRST -data 0x0800 -noe 0x0400
+ftdi layout_init 0x0508 0x0f1b
+ftdi layout_signal nTRST -data 0x0200 -noe 0x0100
+ftdi layout_signal nSRST -data 0x0800 -noe 0x0400

diff --git a/tcl/interface/ftdi/xds100v2.cfg b/tcl/interface/ftdi/xds100v2.cfg
index 860a7585d9845a31a3ed741d078b5719b26fa3da..bda87811bb434bc52e2d2660ea8a033421030ce9 100644 (file)
--- a/tcl/interface/ftdi/xds100v2.cfg
+++ b/tcl/interface/ftdi/xds100v2.cfg
@@ -8,9 +8,9 @@
 #
 
 adapter driver ftdi
-ftdi_vid_pid 0x0403 0xa6d0 0x0403 0x6010
+ftdi vid_pid 0x0403 0xa6d0 0x0403 0x6010
 
-ftdi_layout_init 0x0038 0x597b
+ftdi layout_init 0x0038 0x597b
 
 #  8000 z - unused
 #  4000 0 > CPLD loopback          (all target side pins high-Z)
@@ -45,14 +45,14 @@ ftdi_layout_init 0x0038 0x597b
 # changing the USB configuration to zero.)
 #
 
-ftdi_layout_signal nTRST -data 0x0010
-ftdi_layout_signal nSRST -oe 0x0100
-ftdi_layout_signal EMU_EN -data 0x0020
-ftdi_layout_signal EMU0 -oe 0x0040
-ftdi_layout_signal EMU1 -oe 0x1000
-ftdi_layout_signal PWR_RST -data 0x0800
-ftdi_layout_signal LOOPBACK -data 0x4000
+ftdi layout_signal nTRST -data 0x0010
+ftdi layout_signal nSRST -oe 0x0100
+ftdi layout_signal EMU_EN -data 0x0020
+ftdi layout_signal EMU0 -oe 0x0040
+ftdi layout_signal EMU1 -oe 0x1000
+ftdi layout_signal PWR_RST -data 0x0800
+ftdi layout_signal LOOPBACK -data 0x4000
 
-echo "\nInfo : to use this adapter you MUST add ``init; ftdi_set_signal PWR_RST 1; jtag arp_init'' to the end of your config file!\n"
+echo "\nInfo : to use this adapter you MUST add ``init; ftdi set_signal PWR_RST 1; jtag arp_init'' to the end of your config file!\n"
 # note: rising edge on PWR_RST is also needed after power-cycling the
 # target

diff --git a/tcl/interface/ftdi/xds100v3.cfg b/tcl/interface/ftdi/xds100v3.cfg
index 6c705823ad4c524fd7dd64c840800460da7052c7..43a11bd354f01fd8bdc9b0a820275efceaa2137d 100644 (file)
--- a/tcl/interface/ftdi/xds100v3.cfg
+++ b/tcl/interface/ftdi/xds100v3.cfg
@@ -8,4 +8,4 @@
 source [find interface/ftdi/xds100v2.cfg]
 
 # The USB ids are different.
-ftdi_vid_pid 0x0403 0xa6d1
+ftdi vid_pid 0x0403 0xa6d1